Tender For Repair/Replacement Of Water Supply Pipe Line System At Various Loc Of Dipatoli Mil Stn Under Ge Dipatoli
Tender Value
49 Lakhs
Estimated cost
Bid Submission
31 Oct 2026
15 days left
EMD
98000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ranchi → Jharkhand
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair/Replacement Of Water Supply Pipe Line System At Various Loc Of Dipatoli Mil Stn Under Ge Dipatoli
BOQ
| Sl. No. | Item Description |
| 1 | Excavation in trenches, not exceeding 1.5 metre wide and not exceeding 1.5 metre in depth for laying/ taking out of pipe in soft/loose soil, complete all as directed |
| 2 | Returning/ refilling in trenches including spreading levelling, watering and well ramming in layer not exceeding 25 cm thick, complete all as directed. |
| 3 | Removal of excavated surplus soil not exceeding 50 meter and depositing where directed at level not exceeding 1.5 metre above the starting point, complete all as directed |
| 4 | Cutting existing CI/DI/MS water mains in position for insertion of Tee, branch line etc to new water connection of size 350 mm bore complete all as directed |
| 5 | All as per item No 4 here-in-before but in size 250 mm bore complete. |
| 6 | All as per item No 4 here-in-before but in size 200 mm bore complete. |
| 7 | All as per item No 4 here-in-before but of size 150 mm bore complete. |
| 8 | All as per item No 4 here-in-before but of size 100 mm bore complete. |
| 9 | Taking up CI/DI/MS water mains including all fittings with spigot and socket ends and lead joint including burning out lead joint and recovering lead of CI pipe of size 350 mm bore complete all as directed. |
| 10 | All as per item No 9 here-in-before but in size 250 mm bore complete. |
| 11 | All as per item No 9 here-in-before but in size 200 mm bore complete. |
| 12 | All as per item No 9 here-in-before but of size 150 mm bore complete. |
| 13 | All as per item No 9 here-in-before but of size 100 mm bore complete. |
| 14 | Refixing of CI/DI/MS pipes with socket and spigot end in trenches with necessary fittings in any length including cleaning of size 350 mm dia bore complete all as directed (Excavation and earth work will be measured & paid separately) |
| 15 | All as per item No 14 here-in-before but in size 250 mm bore complete. |
| 16 | All as per item No 14 here-in-before but in size 200 mm bore complete. |
| 17 | All as per item No 14 here-in-before but of size 150 mm bore complete |
| 18 | All as per item No 14 here-in-before but of size 100 mm bore complete. |
| 19 | Supply, laying and jointing of DI pressure pipes with spigot and socket lining in inner side as per IS:8329/2000 (latest revision) and other relevant standards and mettalic zinc/epoxy coating on outer side, suitable for push on joint (rubber gasket joint) including rubber gasket, in any length laid in trenches/ over masonry pillar and connection to old or new position of Class \\"K-7\\" of size 350 mm bore complete all as specified and as directed |
| 20 | All as per item No 19 here-in-before but in size 250 mm bore complete all as specified and directed. |
| 21 | All as per item No 19 here-in-before but in size 200 mm bore complete all as specified and directed. |
| 22 | All as per item No 19 here-in-before but of size 150 mm bore complete all as specified and directed. |
| 23 | All as per item No 19 here-in-before but of size 100 mm bore complete all as specified and directed. |
| 24 | Material and labour for run lead joints of CI pipes of size 350 mm bore complete all as specified and directed. (Excavation and earth work will be measured & paid separately) |
| 25 | All as per item No 24 here-in-before but in size 250 mm bore complete all as specified and directed. |
| 26 | All as per item No 24 here-in-before but in size 200 mm bore complete all as specified and directed. |
| 27 | All as per item No 24 here-in-before but of size 150 mm bore complete all as specified and directed. |
| 28 | All as per item No 24 here-in-before but of size 100 mm bore complete all as specified and directed. |
| 29 | Materail and labour in repair for Rubber gasket (Tyton) joint of size 350 mm bore complete all as specified and directed. (Excavation and earth work will be measured & paid separately) |
| 30 | All as per item No 29 here-in-before but in size 250 mm bore complete all as specified and directed. |
| 31 | All as per item No 29 here-in-before but in size 200 mm bore complete all as specified and directed. |
| 32 | All as per item No 29 here-in-before but of size 150 mm bore complete all as specified and directed. |
| 33 | All as per item No 29 here-in-before but of size 100 mm bore complete all as specified and directed. |
| 34 | Supply and fixing cast iron sluice valve with stainless steel spindle and cast iron hand wheel complying with IS 14846-2000, class PN 1.0 both ends flanged with 2 Nos rubber insertion gasket joints, nuts, bolts and washers of required size & Nos, of size 350 mm dia including taking down old unserviceable CI sluice valve complete all as specified and as directed |
| 35 | All as per item No 34 here-in-before but in size 250 mm bore complete all as specified and directed. |
| 36 | All as per item No 34 here-in-before but in size 200 mm bore complete all as specified and directed. |
| 37 | All as per item No 34 here-in-before but of size 150 mm bore complete all as specified and directed. |
| 38 | All as per item No 34 here-in-before but of size 100 mm bore complete all as specified and directed. |
| 39 | Material and labour for repair/replacement/construction of brick masonry valve pit of size 1200X1200X1200 mm (internal dimensions) one brick thick wall in cement mortar 1:4 on 100 mm thick PCC 1:4:8 (40 mm graded stone aggregate) in foundation, rendering 15 mm thick internally an extrernally upto 150 mm below GL and two coat white wash as plastered surfaces, providing 3.0 mm thick MS sheet valve pit cover cover, welded with 40X5 mm flat iron frame alround incl provn of hinges, handle and locking arrangements and 40X40X6 mm angle iron frame fixed on top of vavle pit by means of holdfast 150 mm ling embedded in PCC 1:2:4 (20 mm graded stone aggregate) block of size 230X200X100 mm, applying two coats of anti-corrosive paint over a coat of red oxide zinc chrome primer after prep of all exposed to steel surfaces incl necy excavation & earth work in soft/loose soil complete all as specified and directed. |
| 40 | Material and labour for repair/replacement/construction of brick masonry valve pit of size 900X900X900 mm (internal dimensions), one brick thick wall in cement mortar 1:4 on 100 mm thick PCC 1:4:8 (40 mm graded stone aggregate) in foundation, rendering 15 mm thick internally an extrernally upto 150 mm below GL and two coat white wash as plastered surfaces, providing 3.0 mm thick MS sheet valve pit cover cover, welded with 40X5 mm flat iron frame alround incl provn of hinges, handle and locking arrangements and 40X40X6 mm angle iron frame fixed on top of vavle pit by means of holdfast 150 mm ling embedded in PCC 1:2:4 (20 mm graded stone aggregate) block of size 230X200X100 mm, applying two coats of anti-corrosive paint over a coat of red oxide zinc chrome primer after prep of all exposed to steel surfaces incl necy excavation & earth work in soft/loose soil complete all as specified and directed. |
| 41 | Material and labour for DI fittings as per IS-9525 for spigot socket pipe such as bends (any type, radius and angle) tappers any type (straight, bend increasing , decreasing or double socket etc) Tee pieces single branch, \\"Y\\" junction, double branch, cross (all socket or socket and plugs) or in form of mechanical joints in any size incl cutting and jointing old/new positions for bends, tees, all types of flanges, socket and spigot, collars caps etc complete all as specified and directed. |
| 42 | Drilling and tapping cast iron water mains in position for branch connections of 15 mm to 20 mm internal dia size complete all as specified and directed. |
| 43 | Supply & Fixing GI tubes medium grade galvanized with necessary fittings and clamps as per SSR Part -1 laid in trenches /wall/floors concealed or open execution including taking down existing old unsv GI pipe of size 15 mm dia bore complete all as specified and directed. |
| 44 | All as per item No 43 here-in-before but of size 20 mm dia bore complete all as specified and directed. |
| 45 | All as per item No 43 here-in-before but of size 25 mm dia bore complete all as specified and directed. |
| 46 | All as per item No 43 here-in-before but of size 40 mm dia bore complete all as specified and directed. |
| 47 | All as per item No 43 here-in-before but of size 50 mm dia bore complete all as specified and directed. |
| 48 | Supply and fixing gun metal globe or gate valve with iron wheel head, screwed both ends with union, long screw with check nut for iron pipe including taking down existing old unsv gate valve of size 15 mm dia bore complete all as specified and directed. |
| 49 | All as per item No 48 here-in-before but of size 20 mm dia bore complete all as specified and directed. |
| 50 | All as per item No 48 here-in-before but of size 25 mm dia bore complete all as specified and directed. |
| 51 | All as per item No 48 here-in-before but of size 40 mm dia bore complete all as specified and directed. |
| 52 | All as per item No 48 here-in-before but of size 50 mm dia bore complete all as specified and directed. |
| 53 | Supply and fixing bib taps cast copper alloy with clutch or butterfly handle screwed down, screwed for iron pipe as per SSR Part-I of size 15 mm bore including taking down existing old unserviceable bib taps complete all as specified and directed. |
| 54 | Supply and fixing in repair ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe or brass ferrule and fixed as specified in SSR Part-I of size 15 mm dia bore including taking down existing old unserceable ball valves complete all as specified and directed. |
| 55 | All as per item No 54 here-in-before but of size 20 mm dia bore complete all as specified and directed. |
| 56 | All as per item No 54 here-in-before but of size 25 mm dia bore complete all as specified and directed. |
| 57 | Material and Labour for PCC 1:2:4 type B1 using 20 mm graded stone aggregate for construction for thrust blocks to the pipe at corners and bends etc complete all as specified and directed. |
| 58 | Supply Only Calcium Hypo Chloride minimum 65 % chlorine packed in standard air sealed plastic containers of size 45 kg each or nearest packing size complete all specified and directed. |
| 59 | Supply only TCCA-90 of Grade-I quality packaging in air sealed plastic containers of 50 kg or nearest packing size complete all as specified and as directed. |
| 60 | Supply only Copper Sulphate of Grade-I quality in proper packaging of 50 kg or nearest packing size complete all as specified and as directed. |
| 61 | Supply only Ferric Alum of Grade-I quality in crystal white colour, in the shape of crystals or lumps for use in swimming pool water filteration complete all as specified and as directed. |
| 62 | Supply only lead wool complete all as specified and as directed. |
| 63 | Supply only lead pig complete all as specified and as directed. |
| 64 | Supply only spun yarn complete all as specified and as directed. |
| 65 | Supply Only GP Epoxy Resin (M-Seal) in 60 GM size pack complete all as specified and as directed. |
| 66 | Supply only teflon tape small size ISI make complete all as specified and directed. |
| 67 | Supply only rubber gasket for water supply works complete all as specified and directed. |
| 68 | Supply only grease complete all as specified and as directed. |
| 69 | Taking up and down and carry to workshop centrifugal pump of capacity 100/75 HP by opening and dismantling from the position for repair/replacement components like bearing roller type, shaft welding and machining work, body asssemble and machining with opening and fitting, chabi machining and fitting, coupling bushing and boring, neck ring policing, nut bolt washers and greasing work and refixing the same in position for smooth functioning of pumping set and testing at full load complete all as specified and as directed. Note :- Any additional item required to complete the job is deemed to be included in the quantity rate. |
| 70 | All as per Item No 69 here-in-before but of capacity 30 HP complete all as specified and as directed. |
| 71 | All as per Item No 69 here-in-before but of capacity 10/7.5 HP complete all as specified and as directed. |
| 72 | Taking up and down & carry to workshop and opening the burnt motor 100/75 HP, 415 Volts and rewinding the same by super enamel copper wire as per existing size/gauge including provision of new insulating material, varnishing and fixing of new ISI make bearing both side and refixing the same in position and testing at full load and commissioning complete all as specified and directed. Note :- Any additional item required to complete the job is deemed to be included in the quantity rate. |
| 73 | All as per Item No 72 here-in-before but of capacity 30 HP complete all as specified and as directed. |
| 74 | All as per Item No 72 here-in-before but of capacity 10/7.5 HP complete all as specified and as directed. |
| 75 | Taking up and down & carry to workshop and opening the booster pump of capcity of .5 to 2 HP, rewinding the same by super enamel copper wire as per existing size/gauge including provision of new insulating material, varnishing and fixing of new ISI make bearing, repair/replacement of impellers, shaft seals, pressure switch, check valve and pressure tank and refixing the same in position and testing at full load and commissioning complete all as specified and directed. Note :- Any additional item like electronic relays, fuses and switches etc required to complete the job is deemed to be included in the quantity rate. |
| 76 | Material and labour for opening and proper closing the existing filtration tank of swimming pool of 8000 gallons per hour capacity for repair/ servicing and cleaning by taking out filter media sand/aggregate/carbon filter media etc and refilling of the same . The job includes for resetting the filtration plant in functional condition as before complete all as specified and directed. |
| 77 | Material and labour for repair/servicing to high pressure single head adjustable gear motor dosing pump by repair/servicing of spare parts like pump tube, suction/discharge tubing, inject check valve, foot ball, adaptor with connecting nut, duck bill, connecting nut, valve o ring, rotor assembly, coil, roller assembly and terminal lugs, nut, bolts, cleaning/repairing of settling tank as required at site including testing of dosing pump sets to check the smooth functioning complete all as specified directed. (Note:- spares/parts like pump tube, suction/discharge tubing, inject check valve, foot ball , adaptor with connecting nut, duck bill, connecting nut, valve o ring, rotor assembly, coil, roller assembly will be measured and paid separetaly.) |
| 78 | Supply and replacement of pump tube suitable for item No 77 complete all as specified and directed. |
| 79 | Supply and replacement of ceramic ball suitable for item No 77 complete all as specified and directed. |
| 80 | Supply and replacement of suction/discharge tubing suitable for item No 77 complete all as specified and directed. |
| 81 | Supply and replacement of inject check valve suitable for item No 77 complete all as specified and directed. |
| 82 | Supply and replacement of teflon washer (ring seal) suitable for item No 77 complete all as specified and directed. |
| 83 | Supply and replacement of weighted suction line strainer suitable for item No 77 complete all as specified and directed. |
| 84 | Supply and replacement of Foot Valve assembly suitable for item No 77 complete all as specified and directed. |
| 85 | Supply and replacement of air release valve suitable for item No 77 complete all as specified and directed. |
| 86 | Supply and replacement of adaptor with connecting nut suitable for item No 77 complete all as specified and directed. |
| 87 | Supply and replacement of duck bill suitable for item No 77 complete all as specified and directed. |
| 88 | Supply and replacement of connecting nut suitable for item No 77 complete all as specified and directed. |
| 89 | Supply and replacement of connecting valve \\"O\\" ring suitable for item No 77 complete all as specified and directed. |
| 90 | Supply and replacement of rottor assembly with bearing bracket suitable for item No 77 complete all as specified and directed. |
| 91 | Supply and replacement of coil suitable for item No 77 complete all as specified and directed. |
| 92 | Supply and replacement of roller assembly suitable for item No 77 complete all as specified and directed. |
| 93 | Supply and replacement of diagphram assembly suitable for item No 77 complete all as specified and directed. |
| 94 | Supply and replacement of PP Head suitable for item No 77 complete all as specified and directed. |
| 95 | Supply and fixing in repair CI body and brass gate heavy duty non return valve (NRV) with by-pass arrangement, IS-5312, ISI marked both ends flanged with 2 Nos rubber insertion gasket joints, nuts, bolts & washers of required size & nos complete of size 250 mm dia complete all as specified and directed |
| 96 | All as per item no 95 here-in-before but of size 150 mm dia complete all as specified and directed. |
| 97 | All as per item no 95 here-in-before but of size 100 mm dia complete all as specified and directed. |
| 98 | Material and labour for mild steel iron frame/sheet work with suitable angle iron/ flat iron and sheet matching with existing insfrastructure on site providing required size of frame/sheet including welding work, provn of hinges, handle, holdfast and locking arrangements etc as required at site, applying two coats of anti-corrosive paint in any prescribed colour matching with existing insfrastructure over a coat of red oxide zinc chrome primer complete all as specified and directed. (Note: No of welding joints will be made all as directed by Engr-in-Charge) |
| 99 | Supply and fixing in replacement Easypact TVS contactor of existing make and model (LC1E160) or equivalent suitable for panel of 75/100 HP Centrifugal Motor Pump complete all as specified and directed. |
| 100 | Supply and fixing in replacement of Easypact TVS contactor of existing make and model (LC1E120) or equivalent suitable for panel of 75/100 HP Centrifugal Motor Pump complete all as specified and directed. |
| 101 | Supply and fixing in replacement of Easypact TVS contactor of existing make and model (LC1E18) or equivalent suitable for panel of Centrifugal Motor Pump complete all as specified and directed. |
| 102 | Supply and fixing in replacement of Easypact TVS contactor of existing make and model (LC1E25) or equivalent suitable for panel of Centrifugal Motor Pump complete all as specified and directed. |
| 103 | Supply and fixing in replacement of Relay Tesys giga circuit breaker of existing make and model (LRE08A) or equivalent suitable for panel of 75/100 HP Centrifugal Motor Pump complete all as specified and directed. |
| 104 | Supply and fixing in replacement of Relay Tesys giga circuit breaker of existing make and size (07 to 10 Amps) suitable for panel of Centrifugal Motor Pump complete all as specified and directed. |
| 105 | Supply and fixing in replacement of Relay Tesys giga circuit breaker of existing make and size (09 to 13 Amps) suitable for panel of Centrifugal Motor Pump complete all as specified and directed. |
| 106 | Supply and fixing in replacement of timer switch of existing make and model (S1ETS1) or equivalent suitable for panel of 75/100 HP Centrifugal Motor Pump complete all as specified and directed. |
| 107 | Supply and fixing in replacement of digital ameter of existing make and model (upto 200 amps range) suitable for panel of Centrifugal Motor Pump complete all as specified and directed. |
| 108 | Supply and fixing in replacement of digital voltmeter of existing make and model (upto 500 volts range) suitable for panel of Centrifugal Motor Pump complete all as specified and directed. |
| 109 | Supply and fix in replacement MCCB 415 volts 3 Pole 250 Amps 50 Hz with thermal adjustable and magnetic adjustable breaking capacity 36 KA complete all as specified and directed at site. |
| 110 | Supply and fix in replacement MCCB 415 volts 4 Pole 200 Amps 50 Hz with thermal adjustable and magnetic adjustable breaking capacity 36 KA complete all as specified and directed at site. |
| 111 | Supply and fix in replacement MCCB 4 Pole 415 volts 160 Amps 50 Hz with thermal adjustable and magnetic adjustable breaking capacity 36 KA complete all as specified and directed at site. |
| 112 | Supply and fix in replacement MCCB 4 Pole 415 volts 100 Amps 50 Hz with thermal adjustable and magnetic adjustable breaking capacity 25 KA complete all as specified and directed at site. |
| 113 | Supply and fixing in replacement single core 70 sqmm copper conductor for 75 to 100 HP centrifugal pumps including copper lugs in required quantity complete all as specified and directed at site. |
| 114 | Supply and fixing in replacement single core 16 sqmm copper conductor for 10 to 30 HP centrifugal pumps including copper lugs 70 sqmm in required quantity complete all as specified and directed at site. S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes confirming to I.S. 1161-1998 Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 15 daysNov 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 22 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender