Tender For 8580/E8 special Repair To Bldg No T-41 At Depot Area For Replacement Of Asbestos Sheet Roofing And Connected Wks Of 6 Mtn Dou Under Ge (East) Bareilly
Tender Value
43.95 Lakhs
Estimated cost
Bid Submission
31 Oct 2026
17 days left
EMD
87900
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bareilly → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for 8580/E8 special Repair To Bldg No T-41 At Depot Area For Replacement Of Asbestos Sheet Roofing And Connected Wks Of 6 Mtn Dou Under Ge (East) Bareilly
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling boarding of any description fixed in any position with nails, complete all as specified and as directed. |
| 2 | Dismanteling of wooden truss/ scanteling purlin rafter etc. complete all as specified and as directed. |
| 3 | Dismantling Asbestos cement (Corrugated, Semicorrugated etc) sheets in roof covering complete all as specified and as directed. |
| 4 | S&F steel work in rolled section as approved, purlins, truss, rafter, posts, gusset plates cleats, wind ties,irorn gate etc including special shape washers etc complete using ERW or induction butt welded tubes confirming to IS 116-1979 grade (medium grade)complete all as specified and as directed. |
| 5 | M&L for prepainted, 0.50mm thick galvalume aluminium zinc AZ-150 coating, GI based corrugated steel (plain or curved) any coloured sheet having tensile strength of 550Mpa as in roof covering & on chajjas fixed with self tapping screws at alternate corrugation etc complete all as specified and as directed. |
| 6 | Demolition of reinforced cement concrete in any position like roofs, floors other than ground floors , beam , staircases , landings , tanks, chajjas,projections, facias and similar suspended work or reinforcement cut as required to facilate demolition for portions ordered to be dismanttled up to 15 m height including forwork and necessary saftey measuresor as directed by Engr in charge complete all as specified and as directed. |
| 7 | M&L for reinforced cement concrete (Design Mix) using 20 mm graded broken stone aggregate as in slabs supported on walls, beams and columns in floors, roofs slab, landings, shelves and the like complete all as specified and as directed. |
| 8 | M&L for Formwork to sides and soffits of floor or roof beams, slab,beam haunchings,girders, bressummers,lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and as directed by Engineer-In-Charge. |
| 9 | S&F mild steel TMT bar of 5 to 10 mm dia and over cut to length bent to shape required including cranking and binding with mild steel annealed wire not less than 0.9 mm dia complete all as specified and as directed. |
| 10 | M & L two coats of synthetic enamel paint on steel surfaces over one coat of red oxide or zinc chrome primer, of any description over 10cm width or girth including preparation of new or previously untreated surfaces of steel. compete all as specified as directed by Engineer -in -charge |
| 11 | Demolition of Brickwork or stone/boulder masonry, built in cement mortar includin gall quoins, arches, pillars,etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and as directed. |
| 12 | M&L Brick work with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM1 : 6 all as specified and directed by Engr-in-Charge |
| 13 | Taking down cement plaster, any description, on brick or stone walls etc, including raking out joints, hacking for key, scrubbing down with water etc and disposal of debris complete all as specified and as directed |
| 14 | M&L rendering 15 mm thick in ready mix internal sand faced cement plaster on brick or concrete surfaces including providing as per manufacturers specifications, surfaced finished even and fair complete all as specified and directed. |
| 15 | M& L for 15mm thick ready mix external sand faced cement plaster on brick or concrete surfaces including providing & mixing water proofing compound as per manufacturers specifications, surfaced finished even and fair complete all as specified and directed. |
| 16 | Preparation of new surface of walls and applying two coat of Oil bound distemper using roller, brushes including in patches over a coat of alkali resistant primer and including 1.50 mm thick cement based wall care putty in two layers with making the surface complete smooth by rubbing etc with minimum 6 hr interval between any two coats complete all as specified and as directed by Engineer in charge |
| 17 | Preparation of new surface of walls by vacuume based sanding machine; scrapping down smoke soot, moulds, moss and efflorescent salts and greasy spots , removing nails etc, and applying 1.50 mm thick cement based wall care putty Two coats of exterior Acrylic emulsion (Apex)/Equivalent of any colour over one coat of exterior water based wall priming on walls with and including provision of scaffolding required for the treatment to external surfaces of building with required safety measures etc complete all as specified and as directed by Engineer in charge. |
| 18 | Complete Removal of existing treatment from old brick/concrete surface on walls and applying two coat of Oil bound distemper using roller, brushes including in patches over a coat of alkali resistant primer and including 1.50 mm thick cement based wall care putty in two layers with making the surface complete smooth by rubbing etc with minimum 6 hr interval between any two coats complete all as specified and as directed by Engineer in charge |
| 19 | Complete removal of existing treatment on old surfaces by vacuume based sanding machine; scrapping down smoke soot, moulds, moss and efflorescent salts and greasy spots , removing nails etc, and applying Two coats of exterior Acrylic emulsion (Apex)/Equivalent of any colour over one coat of exterior water based wall priming on walls with and including provision of scaffolding required for the treatment to external surfaces of building with required safety measures etc complete all as specified and as directed by Engineer in charge. |
| 20 | S&F Horizental level suspended Ceiling comprising of Armstrong GI Clip-in Micro perforated 600x600mm (nominal size) tiles of 120mm galvanised steel as per IS 277 (2003) suitable for architectural finishes in 0.5mm thickness as per in IS:513 (1994) in Global white colour with concealed suspension syayetm having a bevelled edge of 3x3mm and height of 33mm on one side and 18mm on other side. Tile shall have perforated of hole diameter 2.5mm and open area 16% with linear and diagonal pitch of 5.5mm and 7.7mm respectively along with a border of 10mm. The tile shall be electrostaticalkly polyster powder coated using RoHS compliant powder having coating thickness ranging from 60-80microns. Back side of the tile shall have Soundtex fleece hot pressed mechanically for uniform bonding to achieve NRC up to 0.7 all as per manufactures instructions , complete all as specified and as directed by Engineer-In-Charge.Note : If electrical cables are running at site aand required to be relocated electric fittings on walls are required to be shifted including refixing of fan/ light fittings and other light acessarry including making good the wall surface.shall be deemed to be included to the rates. |
| 21 | S&F in repair PVC hollow interlocking wall paneling of 5mm thick prelam PVC sheet. The panel & strips shall be of 600 kg / cbm density manufactured by an ISO-9000 certified company. The strips should two PVC strips. The PVC strip shall be fixed to the wall using 65mm long M.S screws through the groove in the strip by using PVC fasteners. The distance between two screws shall not be more than 200mm. The exact size of the panel and correspondingly of the grid may vary depending on the size of the wall. Optionally a strips of 5mm thick PVC sheet of width 75mm feathered at the edges shall be stuck at the places where two panels are joined, using solvent cement complete all as specified and as directed. |
| 22 | Demolition of cement concrete (unreinforced) in ground floor not exceeding 15cm thickness below or above ground level including floor finishes and removing debris from the site all as specified and as directed. |
| 23 | Dismantling glazed tiles/ kota stone/ terrazzo tiles any type as in dado/ skirting etc; including cement mortar bedding ( but not backing ) complete all as specifide. |
| 24 | M&L 25 mm thick plain cement concrete 1:2:4 type B-1, (20mm graded aggregate) as levelling course/undulation of floor etc, complete all as specified and as directed. |
| 25 | M&L for 16 -18mm thick granite (colour as approved) work (table rubbed and polished) in steps, shelves, jambs, pillars, window-cills, cooking platforms (vertical/ horizontal) and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 10mm thick screed bed or bedding layer in CM 1:4 complete all as specified and as directed. |
| 26 | M&L for machine cut kota stone slab flooring 18-20 mm (+ 2mm) thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing over and including 15mm thick screed bed or bedding layer in CM 1:6 complete all as specified and as directed. |
| 27 | M&L for mirror polished machine cut kota stone slab 15-16 mm thick in riser of steps, skirting, dado and pillar laid over and including 10mm thick rendering in CM 1:4 and jointed complete all as specified and as directed. |
| 28 | M&L for glazed ceramic (coloured) tiles of approved shade and pattern of size 350x 250x7mm/ 450X350X7mm/ 300X450X7 to 8mm thick or any other nearer size as approved by Engineer incharge in vertical surface set and jointed in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:4 as in backing coat of tiles complete all as specified and as directed. |
| 29 | Cement concrete (1:2:4) type B-1 using 20 mm graded stone aggregate as in plinth protection, 50 mm thick, surfaces finished even and fair without using extra cement including provision of construction joints complete all as specified. |
| 30 | M&L for 75mm thick PCC 1:4:8 type D-2, (40mm graded stone aggregate) as in sub floor, sub bases, floor and paving etc; complete all as specified. |
| 31 | Providing and laying 60mm thick factory made table vibratory, PU mould, chamfered edge cement concrete coloured paver block of M-25 grade with approved design & pattern as in footpath, drive ways or parking etc; over and including 50mm thick compacted bed of fine sand and proper embedding/ laying of inter locking paver blocks into the sand bedding layer, filling the joints with sand and cutting of paver blocks as required, complete all as specified and as directed. |
| 32 | M&L for factory made precast cement concrete solid blocks M-30 Grade, using 20 mm graded crushed stone aggregate as in kerb stones of any size (with plain or interlocking joints as directed) set in cement mortar 1:4 for path edgings etc; embedded in position including all necessary excavation, tamping ground arround blocks and removal of rubbish/ surplus soil etc., complete all as specified and directed by Engineer-in-Charge. |
| 33 | Taking down Chowkats or frames with shutters (without taking off shutters from the frames) n.exc. 1.5 sqm each Complete all as specified and as directed by Engineer-In-Charge.. |
| 34 | Taking down Chowkats or frames with shutters (without taking off shutters from the frames) exc. 1.50sqm and n exc 4sqm each Complete all as specified and as directed by Engineer-In-Charge.. |
| 35 | S&F providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S. S. screws, all as per direction of Engineer-in-Charge.Note: stainless steel butt hinges and necessary S. S screws shall not be paid separately. |
| 36 | M & L for powder coated aluminium sliding window with anodized aluminium frame of 3 Track of size 92mmx32mmx 1.5mm thick, with sliding shutters(02 glass and 01 Wirecloth) with necessary channels (top rail, bottom rail and style of size 40mmx 18mm x1.10 mm thick) including glazing with tinted sheet glass panel 4.00mm thick and Aluminum alloy wirecloth 4mm nominal dia and avg width of aperture 1.4mm, fitted with necessary jointing cleats, glazing clips,locking device one for each shutter , rubber packing, aluminium beading, screws, rawl plugs including all necessary holes / drilling etc, complete all as specified as directed by Engineer -in -charge. Note : If mentioned section are not available in market, then immediate next higher section shall be provided by Contractor without any extra cost. |
| 37 | S & F 150 mm aluminium anodised barrel tower bolts of extruded section, ISI marked compete all as specified as directed by Engineer -in -charge |
| 38 | S & F 150 mm extruded aluminium alloy handles , fabricated type, anodised, ISI marked compete all as specified as directed by Engineer -in -charge |
| 39 | S & F 100 mm MS butt hinges medium weight cold rolled mild steel compete all as specified as directed by Engineer -in -charge |
| 40 | S & F 300 mm long and Mild steel Chromium plated sliding door bolts, plate type, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed compete all as specified as directed by Engineer -in -charge |
| 41 | S & F mild steel spring 250mm for door, ordinary rat tail rod pattern springs, including roller and roller plate including welding as required for steel frame compete all as specified as directed by Engineer -in -charge |
| 42 | M & L two coats of synthetic enamel paint over one coat of pink primer on wood or wooden based surface exc. 10cm width or girth including preparation of new or previously untreated surfaces.compete all as specified as directed by Engineer -in -charge |
| 43 | S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65 x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), Calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with milter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/ SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: M. S. hold fast/ lugs or SS dash fasteners shall not be paid for separately. Please Enable Macros to View BoQ information |
| 44 | S&F for factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65 x125 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), Calcium carbonate and natural fibres (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with milter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/ SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. Note: M. S. hold fast/ lugs or SS dash fasteners shall not be paid for separately. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 10, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysNov 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 24 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender