Tender For Renovation And Designing Of Anm Chamber And Office Room At Haddo Under Sd-Ii, Svpnd, Apwd, Sri Vijaya Puram.
Tender Value
24.83 Lakhs
Estimated cost
Bid Submission
09 Nov 2026
8 days left
EMD
49662
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
South Andamans → Andaman And Nicobar Islands
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation And Designing Of Anm Chamber And Office Room At Haddo Under Sd-Ii, Svpnd, Apwd, Sri Vijaya Puram.
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 30-Oct-2026 | Corrigendum-I | Date | 09-Nov-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Providing wood work in frames of partitions etc sawn and fixed in position with necesary stainless steel screws etc. as per direction of Engineer-in-charge. |
| 2 | Superior Hardwood Cat-II(A) |
| 3 | Providing and fixing marine plywood partition/panelling of approved quality (Green ply, SIR or equivalent) confirming to IS:710 with necessary nails and screws etc. complete (frame work to be paid separately). |
| 4 | 6mm thick marine plywood |
| 5 | 12mm thick marine plywood |
| 6 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : |
| 7 | For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron) |
| 8 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. |
| 9 | Pre-laminated particle board with decorative lamination on both sides |
| 10 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): |
| 11 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 12 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. |
| 13 | 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 14 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : |
| 15 | Of area 3 sq. metres and below |
| 16 | Providing and fixing 35mm thick panelled, glazed or panelled shutters for door including Stainless steel Butt hinges with necessary screws with Superior hardwood Cat-II (A) including panelling with 12mm thick superior hardwood cat-II (A) planks etc. complete with wooden cleats & blocks as directed by the Engineer-in-charge. |
| 17 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). |
| 18 | Superior hardwood Cart-II (A) |
| 19 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 20 | 125 mm |
| 21 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 22 | 300x16 mm |
| 23 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 24 | 150x10 mm |
| 25 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 26 | Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge |
| 27 | 50 mm average thickness |
| 28 | Replacement of reinforcement a additional bars i/c bending cutting, welding and fixings excluding the cost of steel all labour charges, minor tools etc complete (Steel steel be issued by Department free of cost) |
| 29 | Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge. |
| 30 | Bars upto 12 mm diameter |
| 31 | Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer- In-charge complete in all respect. |
| 32 | Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make |
| 33 | Shotcreting R.C.C. columns, beams and slabs etc. in layers with approved design mix concrete having the specified minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stone aggregate of 10 mm maximum size in proportion as per design criteria] including the cost of centering and shuttering at edges and corners etc. as directed by Engineer- in-Charge Note: Rates shall include the providing necessary ground wires etc. The levelling gauges, if used, shall be paid for separately. Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/tapping with a blunt metal instrument. |
| 34 | 75 mm thick in Grade M25 with cement content not less than 330 kg per cum |
| 35 | Providing and fixing single scaffolding system on the exterior side with 100mm dia bamboo 2.0 mtrs centre to centre horizontal and vertical jointing with coir rope with provided staircase system in the scaffolding for working platform etc and removing it thereafter. The scaffolding system shall be stiffened with bracing, runners connectin with the building etc with essential safety features for the workman etc complee as per the direction and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. |
| 36 | Cleaning of existing old terrazzo floor to remove dirt, dust and old wax or coatings after cleaning grinding of clean surface with finer-grit diamond grinder to smooth act the surface. Then apply a terrazzo polish to the floor using a lambs wool applicator or a polishing machine. Finally buffing the floor and achieve a high gloss finish as per the direction of Engineer-in-charge. |
| 37 | Repair to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sqm and under, including cutting the patch in proper shape, raking out joints and preparing plastering the wall surface with white cement based polymer modified self curing mortar, including disposal of rubbish, all complete as per the direction of Engineer-In-Charge. |
| 38 | Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade. |
| 39 | One or more coats on old work. |
| 40 | Providing and fixing File Storage having one unit maximum side of block 6.00m (L) x 0.45m (W) x 0.75m (H) alongwith one centre shelves and open shutters made of superior quality marine plywood of 19mm thick (Greenply or equivalent) confirming to IS 710 in three sides and 6mm thick marine plywood (Greenply or equivalent) confirming to IS 710 at backside and all outer visible surface pasted with sunmica as per the colour and design approved by the Engineer-in-charge. The cabinet fixed on wall inside surface painted with enamel paint and smoothening the surface with chalk putty. |
| 41 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 42 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 43 | In stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete |
| 44 | Providing and fixing hand rail of approved size by welding etc. to steel ladder railing, balcony railing, staircase railing and similar works, including applying priming coat of approved steel primer. |
| 45 | M.S. tube |
| 46 | Applying priming coat: |
| 47 | With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron/ steel works |
| 48 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: |
| 49 | Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture |
| 50 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 51 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 52 | 1:2:4 (1 Cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 53 | Providing and fixing pre-painted galvalume (PPGL) steel profile sheets AZ-150 of brand of Tata blue scope Steel/Everest Industries Limited, JSW Steel Limited, Jindal India Limited or or equivalent (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.50%), total coated thickness with aluminium zinc coating 150 gsm as per IS: 277 in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws (Xylan) of size (5.5x 55mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 54 | Providing and fixing Pre-Painted galvalume (PPGL) steel profile sheets AZ-150 of brand Tata Blue Scope stee, Everest industries Ltd, JSW Steel Ltd, Jindal Steel Ltd or equivalent make roofing accessories 0.50 mm (+0.50%) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete |
| 55 | Ridges Plain (500-600mm) |
| 56 | Extra for providing and fixing wind ties of 40x6mm flat aluminium section Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 30, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Nov 09, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 8 daysNov 09, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysNov 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender