Tender For Resurfacing Of Runway Alongwith Connected Works At Af Station Ambala.
Tender Value
456 Crore
Estimated cost
Bid Submission
03 Nov 2026
23 days left
EMD
15 Lakhs
Bank guarantee accepted
Document Fee
3000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ambala → Haryana
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Resurfacing Of Runway Alongwith Connected Works At Af Station Ambala.
BOQ
| Sl. No. | Item Description |
| 1 | FLEXIBLE, RIGID PAVEMENT AND FOD TRAP (PART-I) |
| 2 | Demolition of cement concrete (un-reinforced) PQC of any description and in any position not otherwise specifically provided for using pneumatic tools (PQC/DLC/Bituminious material), complete all as specified and directed by Engr-in-Charge. |
| 3 | M&L for crushing the demolished PQC/PCC (obtained from demolition of rigid pavements), screening, segregating, stacking aggregate and like serviceable material found, by mechanical means using stone crusher to required grading (Grading-V of Table 400-9 of MoRTH), removing the wastage and depositing where directed complete all as specified. |
| 4 | Milling /Chiselling of flexible pavement of any description and in any position not otherwise specifically provided for using mechanical milling machine to achieve the level for laying minimum required thickness of DBM layer or to match the slope with adjoining surface (ramping), complete all as specified and directed. |
| 5 | Excavation over area by mechanical means (Hydraulic excavator) in hard/dense soil, including getting out and disposal of excavated earth upto 50m lead and lift upto 1.5m, as directed by Engineer-in Charge complete all as specified. |
| 6 | Removing demolished material retrieved from PQC, DLC, WBM/WMM & GSB Layers and/or miling/chiseling to outside of MoD land of any lead, including disposal in civil area at contractor's own arrangement, including loading, unloading and tacking at the destination complete all as specified and directed. |
| 7 | Excavation by mechanical means (Hydraulic excavator) over areas in any kind of soils, including getting out and disposal of excavated earth lead upto 50m and lift upto 1.5m, as directed by Engineer-in Charge complete all as specified and directed. |
| 8 | Removing excavated material (excavated earth) within MoD land upto 7km and depositing where directed at a level not exceeding 1.5 metre above the starting point complete all as specified and directed. |
| 9 | Excavation over areas by mechanical means (Hydraulic excavator) in soft / loose soil, n exc 1.5m in depth, including getting out and disposal of excavated earth lead upto 50m and lift upto 1.5m, complete all as specified and as directed by Engineer-in-Charge. |
| 10 | Removing demolished material etc. (retrieved from PQC) to a distance 2.5km to 3km beyond lead included in the rates to the crusher plant, including loading, unloading and stacking at the destination complete all as specified and directed.Note:- Material retrieved from this item shall be used as GSB after crushing, under NLB surface or any other similar location where specifically mentioned. |
| 11 | Removing excavated materials for distance exc 1.5km but n exc 5km and deposited where directed at a level not exceeding 1.5 metre above the starting point all as directed. |
| 12 | Removing excavated material exc 500m but n exc 1 km and deposited where directed at a level not exceeding 1.5 metre above the starting point all as directed. |
| 13 | M&L for forming embankment including raising (or lowering) earth, spreading in layers n exc 30cm thick, watering , ramming / rolling and finishing to required size, shape , etc n exc 1.5m from base complete all as specified and directed. (Earth obtained from excavation under item No. 1.08 above) |
| 14 | Removing excavated material (excavated earth) within MoD land upto 7km and deposited where directed at a level not exceeding 1.5 metre above the starting point all as directed. |
| 15 | Soil stabilization of 450 mm sub grade soil by uniform mixing of cement (OPC 43 grade@ 5% cement by weight of soil as additive (percentage required for blending will be as per mix design) to achieve CBR value 6.0, including pulverziation of soil spreading of additive, blending mix by tractor compaction using suitable vibratory roller to achieve density of 98% Maximum Dry Density complete as specified and directed.Note: The actual quantity of cement to be mixed shall be decided as per the design mix parameter and supply only cement shall be measured and paid separately. |
| 16 | Soil stabilization of 450 mm sub grade soil by uniform mixing of cement OPC 43 grade@ 5% cement by weight of soil as additive (percentage required for blending will be as per mix design) to achieve K-value 4 Kg/Sqcm/cm. including pulverziation of soil spreading of additive, blending mix by tractor compaction using suitable vibratory roller to achieve density of 98% Maximum Dry Density complete as specified and directed.Note: The actual quantity of cement to be mixed shall be decided as per the design mix parameter and supply only cement shall be measured and paid separately. |
| 17 | Soil stabilization of 450 mm sub grade soil by uniform mixing of cement OPC 43 grade@ 5% cement by weight of soil as additive (percentage required for blending will be as per mix design) to achieve K- value 3.0Kg/Sqcm/cm, including pulverziation of soil spreading of additive, blending mix by tractor compaction using suitable vibratory roller to achieve density of 98% Maximum Dry Density complete as specified and directed.Note: The actual quantity of cement to be mixed shall be decided as per the design mix parameter and supply only cement shall be measured and paid separately. |
| 18 | Soil stabilization of 300 mm sub grade soil by uniform mixing of cement OPC 43 grade@ 5% cement by weight of soil as additive (percentage required for blending will be as per mix design) to achieve K- value 5.0Kg/Sqcm/cm, including pulverziation of soil spreading of additive, blending mix by tractor compaction using suitable vibratory roller to achieve density of 98% Maximum Dry Density complete as specified and directed.Note: The actual quantity of cement to be mixed shall be decided as per the design mix parameter and supply only cement shall be measured and paid separately. |
| 19 | Supply only cement Ordinary Portland (OPC 43 Grade) |
| 20 | M&L for laying and compacting 200 mm thick (compacted thickness) in two layers of 100 mm thick each Wet Mix Macadam (WMM) grading as per table 400-13 of MoRTH specifications for Road and Bridge works 2013 manufactured in WMM plant, material comprising of clean, crushed, graded aggregate and granular material premixed with water to a dense mass, spreading with sensor paver and rolling with vibratory roller of capacity 80-100KN static weight and consolidating to required gradient and camber the finished surface tolerances to be as per Table 900-1 of MoRTH specifications for Road and Bridge works 2013 complete all as specified and directed. |
| 21 | M&L for laying and compacting 150mm thick (compacted thickness) Wet Mix Macadam (WMM) laid in two layers of 75mm each, grading as per table 400-13 of MoRTH specifications for Road and Bridge works 2013 manufactured in WMM plant material comprising of clean, crushed, graded aggregate and granular material premixed with water to a dense mass, spreading with sensor paver and rolling with vibratory roller of capacity 80-100kN static weight and consolidating to required gradient and camber . The finished surface tolerances to be as per Table 900-1 of MoRTH specifications for Road and Bridge work 2013. complete all as specified and directed by Engineer-in Charge |
| 22 | M&L for preparing black top surfaces by using mechanical wire brush brooms for removing caked mud, rubber deposits, any type of paints on runway surface etc. sweeping with brooms and finally fanning the cleaned surface by applying air pressure to remove all loose dirt etc. complete all as specified and directed. |
| 23 | M&L for applying evenly a prime coat of cationic bitumen emulsion SS1 confirming to IS: 8887 at a rate of application of 0.7-1kg/Sq.m on surface of WMM/WBM as specified in table 500-3 of MoRTH specification for road and bridge works 2013, using mechanical sprayer complete all as complete all as specified and directed |
| 24 | M&L for applying evenly a Tack coat of Bitumen VG-10 grade conforming to IS: 73 at a rate of application of 0.3-0.4kg/sqm (3kg/10Sqm) on bituminous surface as specified in Table 500-5 of MoRTH specification for road and bridge works 2013, using mechanical sprayer complete all as complete all as specified and directed |
| 25 | M&L for providing and consolidating premixed Dense Bituminous Macadam (DBM Grading-II) using min 4.5% VG-40 grade binder by weight of total mix, consolidated thickness 100mm or less but not less than 60mm, gradation as per Grading 2 of Table 500-10 of MoRTH specification for road and bridge works 2013, rolled and compacted to required camber and gradient complete all as specified and directed.Note- (i) No price adjustment shall be applicable if excess quantity of binder content is used / approved subsequent to approval of job mix formula in the execution of work under this item. (ii) No adjustment in quantity of cement (Filler) as per approved design mix / job mix formula shall be made.(iii) Trial bay as specified here in after shall be prepared but no payment shall be made for the same. Unit rate quoted shall be inclusive of this provision. (iv) Work shall be done by using hot mix plant and sensor paver. |
| 26 | M&L for providing and consolidating 50 mm thick premix Dense Asphaltic Concrete (DAC-I) using min 5.4% Elastomeric PMB 76-10 (Marshall stability 1400 Kg) binder by weight of total mix. aggregate gradation as per Bituminous Concrete Grading 1 of Table 500-17 of MoRTH specification for road and bridge works 2013, rolled and compacted to required camber and gradient complete all as specified and directed. |
| 27 | M&L for providing and consolidating 50 mm thick premix Dense Asphaltic Concrete (DAC-II) using min 5.6% Elastomeric PMB 76-10 (Marshall stability 1400 Kg) binder by weight of total mix. aggregate gradation as per Bituminous Concrete Grading 2 of Table 500-17 of MoRTH specification for road and bridge works 2013, rolled and compacted to required camber and gradient complete all as specified and directed.Note or Srl No. 1.25 & 1.26 above- (i) No price adjustment shall be applicable if excess quantity of binder content (polymer modified bitumen) is used / approved subsequent to approval of job mix formula in the execution of work under this item. (ii) No adjustment in quantity of cement (Filler) as per approved design mix / job mix formula shall be made.(iii) Trial bay as specified here in after shall be prepared but no payment shall be made for the same. Unit rate quoted shall be inclusive of this provision. (iv) Work shall be done by using hot mix plant and sensor paver. |
| 28 | M&L for self adhesive glass grid (1.5m wide with 100kN/m longitudinal and transverse strength) laying mechanically complete all as specified and directed. |
| 29 | M&L for SAMI layer using PMB @ 9kg/10Sq.m and chips of size 8-10mm @ 7kg/Sq.m over mechanically laid glass grid complete all as specified and directed by Engr-in-Charge. |
| 30 | M&L for preparing new concrete surface/ bituminious surfaces and painting lines, dashes continuous/ uninterrupted arrows, letters etc and the like exc. 10 cm width with three coats of water based runway marking paint (reflective type) ISI Mark in white, golden, yellow, orange or red colour over a coat of priming paint using mechanised runway marking and painting equipment complete all as specified and as directed. |
| 31 | M&L for preparing new concrete surface/ bituminious surfaces and painting lines, dashes continuous/uninterrupted arrows, letters,etc not exceeding 10cm width with three coats of oil based runway marking paint (reflective type) ISI Mark in white, golden, yellow, orange or red colour over a coat of primer complete all using mechanised runway marking and painting equipment complete all as specified and as directed. |
| 32 | M&L for cutting existing crack in bitumen surface not exceeding 40mm wide at top and 50mm to 75mm in depth 'V' groove with a cutter/router machine; cleaning with compresssed air using compressor, brushing hard and filling crack with rubberised bitumen (CRMB) as per manufacturer's instruction complete all as specified and directed. |
| 33 | Rolling and consolidating formation surfaces in cutting with exc 8tonne and n exc 12tonne complete all as specified and directed. |
| 34 | M&L for laying and compacting Granular Sub Base Course (GSB) 200mm thick (compacted thickness), grading as per Grade V as specified in Table 400-1 of MoRTH specifications for Road and Bridge works 2013, in a single layer over compacted subgrade with natural sand, crushed gravel, crushed stone, crushed slag or combination thereof as per the grading required. The materials are mechanically mixed, spread and leveling on the subgrade by using motor grader of adequate capacity, and rolling with vibratory roller of capacity 80-100kN static weight for achieving required compaction density of atleast 98% of the Maximum Dry Density, consolidating to required gradient and camber with finished surface tolerances as per Table 900-1 of MoRTH specifications for Road and Bridge works 2013. complete all as specified and directed. |
| 35 | M&L for laying and compacting Granular Sub Base Course (GSB) 300mm thick (compacted thickness), grading as per Grade V as specified in Table 400-1 of MoRTH specifications for Road and Bridge works 2013, in a single layer over compacted subgrade with natural sand, crushed gravel, crushed stone, crushed slag or combination thereof as per the grading required. The materials are mechanically mixed, spread and leveling on the subgrade by using motor grader of adequate capacity, and rolling with vibratory roller of capacity 80-100kN static weight for achieving required compaction density of atleast 98% of the Maximum Dry Density, consolidating to required gradient and camber with finished surface tolerances as per Table 900-1 of MoRTH specifications for Road and Bridge works 2013. |
| 36 | M&L for Laying and compacting Granular Sub Base Course (GSB) 150mm thick (compacted thickness), grading as per Grade V as specified in Table 400-1 of MoRTH specifications for Road and Bridge works 2013 by using material produced by crushing plant after crushing of PQC/PCC obtained from demolishing of rigid pavements and adding any deficient material obtained at his own cost to obtain grading in a single layer over compacted subgrade The materials are mechanically mixed, spread and leveling on the subgrade by using motor grader of adequate capacity, and rolling with vibratory roller of capacity 80-100kN static weight for achieving required compaction density of atleast 98% of the Maximum Dry Density, consolidating to required gradient and camber with finished surface tolerances as per Table 900-1 of MoRTH specifications for Road and Bridge works 2013 complete all as specified and directed. complete all as specified and directed. |
| 37 | M&L for Laying and compacting Granular Sub Base Course (GSB) 150mm thick (compacted thickness), grading as per Grade V as specified in Table 900-1 of MORTH specifications for Road and Bridge works, 2013, in a single layer over compacted subgrade with natural sand, crushed gravel, crushed stone, crushed slag or combination thereof as per the grading required. The materials are mechanically mixed, spread and leveling on the subgrade by using motor grader of adequate capacity, and rolling with vibratory roller of capacity 80-100 kN static weight for achieving required compaction density of atleast 98% of the Maximum Dry Density. Consolidating to required gradient and camber complete all as specified and directed with finished surface tolerances as per Table 900-1 of MORTH specifications for Road and Bridge works, 2013. |
| 38 | M&L for Laying and compacting Granular Sub Base Course (GSB) 200mm thick (compacted thickness), grading as per Grade V as specified in Table 400-1 of MoRTH specifications for Road and Bridge works 2013 by using material produced by crushing plant after crushing of PQC/PCC obtained from demolishing of rigid pavements in a single layer over compacted subgrade The materials are mechanically mixed, spread and leveling on the subgrade by using motor grader of adequate capacity, and rolling with vibratory roller of capacity 80-100kN static weight for achieving required compaction density of atleast 98% of the Maximum Dry Density, consolidating to required gradient and camber with finished surface tolerances as per Table 900-1 of MoRTH specifications for Road and Bridge works 2013 complete all as specified and directed. complete all as specified and directed. Please Enable Macros to View BoQ information |
| 39 | M&L for Laying and compacting Granular Sub Base Course (GSB) 200mm thick (compacted thickness), grading as per Grade V as specified in Table 400-1 of MoRTH specifications for Road and Bridge works 2013 by using material produced by crushing plant after crushing of PQC/PCC obtained from demolishing of rigid pavements in a single layer over compacted subgrade The materials are mechanically mixed, spread and leveling on the subgrade by using motor grader of adequate capacity, and rolling with vibratory roller of capacity 80-100kN static weight for achieving required compaction density of atleast 98% of the Maximum Dry Density, consolidating to required gradient and camber with finished surface tolerances as per Table 900-1 of MoRTH specifications for Road and Bridge works 2013 complete all as specified and directed. complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 23 daysNov 05, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender