Tender For Improvement Of Water Supply With Cleaning, Washing And Replacing Of Existing Pipes And Valves By Cut & Flush Work Including Installation Of Valves, Others Allied Works To Removed Contamination From 59, Sailo Kumar Mukherjee Lane To 13, Wat
Tender Value
1.65 Lakhs
Estimated cost
Bid Submission
31 Oct 2026
8 days left
EMD
3303
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Howrah → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Improvement Of Water Supply With Cleaning, Washing And Replacing Of Existing Pipes And Valves By Cut & Flush Work Including Installation Of Valves, Others Allied Works To Removed Contamination From 59, Sailo Kumar Mukherjee Lane To 13, Watkings Lane Via 34, Sailo Kumar Mukherjee Lane, 24/1, Rose Mery Lane And 15, Sailo Kumar Mukherjee Lane Under Ward No-13, Of Hmc.
BOQ
| Sl. No. | Item Description |
| 1 | Excavation of trial pit (3.0 m x 1.0 m x (upto) 3.0 m) for fixing of pumping main, washout line raking every detection against damage of S.W. pipe line electrical cable etc. as underground obstruction including 37.5 mm timber shuttering, earth cutting, dewatering, barricading and back filling etc. as per direction of E-I-C.Ref:- UD & MAD (Schedule) 2018, P-2, it. No. - 1.4 |
| 2 | Dismantling all types of plain cement concrete works, stacking serviceable materials at site and removing rubbish as directed within a lead of 75 m.In ground floor including roof.a) upto 150 mm. ThickRef: P.W.D (Bldg) Sch. -2017, page -10 It- 2(a) |
| 3 | Earth work in excavation of foundation trenches or drains, in all sorts of soil (including mixed soil but excluding laterite or sandstone) including removing, spreading or stacking the spoils within a lead of 75 m. as directed. The item includes necessary trimming the sides of trenches, levelling, dressing and ramming the bottom, bailing out water as required complete.(a) Depth of excavation not exceeding 1,500 mm.[Ref : P.W.D.(Bldg) 2017, Page - 1, Item-2(a)] |
| 4 | Hire and labour charges for 75 mm dia bamboo railing on Jhau/Eucalyptus or other approved timber\bamboo posts 1.4 m above G.L and 0.60 m below G.L including tying strongly with coir ropes and boring holes for posts in any soil/ concrete surface/Bituminious surface packing the sides etc including cost of carriage of all materials and labour complete including cost of restoration to the damages of the ground to its original condition as per direction of Engineer in charge after removing the barricade.(Cost of restoration would be paid seperately.)(a)75mm. dia bamboo railing & 125mm. Dia Jhau/Eucalyptus/otherapproved timber posts @ 1.60m apart(ii) Railing with 3 rows.Ref:- UD & MAD (Schedule) 2018, P-3, it - 1.8(a)(ii) |
| 5 | Filling in foundation or plinth by silver sand in layers not exceeding 150 mm as directed and consolidating the same by thorough saturation with water, ramming complete including the cost of supply of sand. (Payment to be made on measurement of finished quantity)Ref:-[Page:2; Item No:4(A) of PWD-SOR(Bld) 2017] |
| 6 | Flange joint to C.l./D.l/MS. pipes and specials including supply of rubber gasket. nuts. bolts. washers etc. of best quality to make the joint watertight at required hydraulic pressure all complete as per specification & direction of the Engineer-in-Charge. (b) 100 mm dia.Ref:- UD & MAD (Schedule) 2018, P-8, IT-2.1.6 |
| 7 | Cutting of C.l/D.I pipes for fitting with pipes and-or specials of similar or dissimilar materials at the time of laying without damaging any part of the required length including taking out of the broken pieces from the trench and restacking the same at the specified location as per direction of the Engineer-in-charge.(b) 100 mm diaRef:-UD & MAD (Schedule) 2018, P-09, IT-2.1.7 |
| 8 | Lowering, fitting and fixing of all types of valves in proper position andalignment using chain pully block or crane (for diameter above 250 mm) by providing temporary support, as required, gaskets, nuts & bolts etc. all cornplete as per specification and direction of the Engineer-in-charge. [The rate Includes cost of flange joints](a) 100 mm Dia.Ref:-UD & MAD (Schedule) 2018, P-17, IT-2.4.1 |
| 9 | (a) 150 mm Dia.Ref:-UD & MAD (Schedule) 2018, P-17, IT-2.4.1 |
| 10 | Cast iron double flanged manually operated sluice valves generally conforming to IS 14846 : 2000, having four faces and spindle nut inside screw non- rising spindle type gunmetal/AISI 410 suitable for PN 1.0 rating complete with ball thrust bearing and enclosed gearbox (EN-8 with hardened by nitriding pinions of EN-19), flanges flat facedand drilled to IS.: 1538 : 1993. Valves tested by closed end method.NB Diameter in mm(a) 100 mm Dia.Ref:-UD & MAD (Schedule) 2018, P-46 , IT-8.6. |
| 11 | (a) 150 mm Dia.Ref:-UD & MAD (Schedule) 2018, P-17, IT-2.4.1 |
| 12 | Dewatering by pumps including all leads, lifts and making all arrangements of disposal, where continuous flow of water from a source other than natural or ground water is encountered in case of emergency maintenance works related to leakage, breakage and making wet connections. [Note : - In case of any other situation demanding such emergency dewatering. use of this item is to be approved by the Superintending Engineer/Tender Accepting Authority. This item shall be executed on the specific direction duly supported by proper clarification of the E.I.C. who will be satisfied in absolute discretion that such work has not been necessitated due to any natural source of water or any fault of the ContractorRef:-UD & MAD (Schedule) 2018, P-24, it - 7.2 |
| 13 | Hire & labour charges for diesel generating set for lighting including fuel, 300M wire, 11 points with 200 Watt bulb with post for hanging & maintaining the same for day & night for the period.Ref:-UD & MAD (Schedule) 2018, P-4, it - 1.13 |
| 14 | Drilling and tapping C.I. main.(ii) Above 15 mm upto 25 mmRef:-PWD(S&P) w.e.f.- 01.11.17, P-27, It-18 (ii) |
| 15 | Detachable joints to AC pipes including supply of rubber gasket, nuts, bolts etc. of best quality to make the joint water tight at required hydraulic pressure all complete as per specification and direction o the Engineerin- charge.(b) 100 mm dia.Ref:-UD & MAD (Schedule) 2018, P-11, it - 2.2.3 |
| 16 | Labour for detachable joints to AC pipes to make the joint water tight at required hydraulic pressure all complete as per specification and direction of the Engineer-in-charge(b) 100 mm dia.Ref:-UD & MAD (Schedule) 2018, P-12, it - 2.2.4 |
| 17 | Supplying, fitting and fixing of C.I. Mechanical Compression flexible Collar Couplings suitable for C.I. Spun Pipes (as per IS: 1536) and D. I. Pipes (as per IS: 8329) complete with Sealing Rubber Gasket of EPDM quality (IS:5382/1985 Type - 4), Cast Iron Follower Glands and Mild Steel Nut Bolts (Zinc Coated). The whole assembly should be mechanically and hydraulically tested to the provisions as laid down in IS: 1538. Fitting and fixing should be in proper position with proper care of main pipe line for leak proof condition.(b) 100 mm dia.Ref:-UD & MAD (Schedule) 2018, P-27, it - 7.16 |
| 18 | Earth work in filling in foundation trenches or plinth with good earth, in layers not exceeding 150 mm. including watering and ramming etc. layer by layer complete.(Payment to be made based on the basis of measurement of finished quantity of work.(a) With earth obtained from excavation of foundationRef:-UD & MAD (Schedule) 2018, P-01, it - 1.2(a) |
| 19 | Removal of rubbish, earth etc. from the working site and disposal of the same beyond the compound, in conformity with the Municipal / Corporation Rules for such disposal, loading into truck and cleaning the site in all respect as per direction of Engineer in charge.Ref:-UD & MAD (Schedule) 2018, P-5, it - 1.18 |
| 20 | Hire charges for engaging Air Compressor machine with minimum pressure capacity of 5.0 Kg/sq.cm arrangement including all necessary equipment and operating staff, carriage, fuel, Tools and plants all complete for cutting Road / hard crust cutting with pneumatic hammer at desired point in water supply works as per direction of EIC.b) Without Pneumatic hammersFor minimum engagement of 8 hrs. in a dayRef:-UD & MAD (Schedule) 2018, P-53, It. No - 8.29 |
| 21 | Supplying, fitting and fixing in position G.I. pipes of TATA make for underground works with all necessary accessories,specials viz.socket, bend, tee, union, cross, elbow, nipple, short piece etc.including cost of all materials,jointing materials ,cutting pipes,making threads,cutting trenches upto 1.5 metre below surface in all sorts of soil and refilling the same as directed with two coats of painting on G.I. pipes and specials with bituminous paint complete in all respect. (Payment will be made on the centre line measurement of the total pipe line including all specials No separate payment will be made for accessories, specials.Payment for painting will be made seperately)(i) 15 mm dia. medium quality.Ref:-PWD(S&P) 2017, P-3, It-2(i) & (ii). |
| 22 | Add GST |
| 23 | Add 1 % Cess Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 8 daysNov 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender