Tender For Supplying And Erecting 8 Mtr Decorative Street Light Pole With Led At Railway Station Gate To D Mart , Malegoan Road, Dhule.
Tender Value
24.99 Lakhs
Estimated cost
Bid Submission
16 Oct 2026
6 days left
EMD
24996
Bank guarantee accepted
Document Fee
1475
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dhule → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Supplying And Erecting 8 Mtr Decorative Street Light Pole With Led At Railway Station Gate To D Mart , Malegoan Road, Dhule.
BOQ
| Sl. No. | Item Description |
| 1 | Providing pipe type earthing with 40mm. dia. G.l. pipe or 20 mm dia. G.l. Rod complete with all materials as per specification No. EA-EP (9-1-4) |
| 2 | Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. EA-EP |
| 3 | Supplying and erecting mains with 3x2.5 sq.mm FRLSH copper PVC insulated wire laid in provided conduit /trunking /inside pole/Bus bars or any other places as per specification No: WG-MA/BW |
| 4 | Supplying, erecting & marking SPMCB 6A to 32A, B-series with rated short - circuit breaking capacity (Icn) 10kA in provided distribution board as per specification no. SW-SWR/MCB |
| 5 | Making M- 20 grade reinforced cement concrete foundation by consideringthe safe soil bearing capacity at site as 10 T/sq.m at 1.5 m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help oftemplate, duly plastered as per design complete (for 9m & 10m high octagonal /conical GI pole). |
| 6 | Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete. |
| 7 | Supplying, erecting & terminating FR XLPE insulated, galvanised steel formedwire armoured (strip) cable 1100 V, 4 core 16 sq. mm. aluminium conductorcomplete erected with glands & lugs, on wall/ trusses/pole or laid in providedtrench/ pipe as per specification no. CB-LT/AL |
| 8 | Supplying & erecting G.I. pipe ‘A’ class 40 mm dia. erected for enclosing XLPE armoured cable on wall/pole as per specification no. CB-CE |
| 9 | Supplying and erecting iron work, sheet metal work consisting of CRCAsheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drillingand welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match theswitchgears or as per directions by the authority. |
| 10 | Providing, designing, fabricating, casting, supplying, transporting, erecting, aligning, testing and commissioning one complete 8.0 m overall-height decorative street-light pole assembly, comprising a 6.35 m main shaft, 1.65 m upper decorative assembly and 1.50 m overall double-arm bracket. The pole shall consist of sound, defect-free cast-iron ornamental components reinforced with suitably designed structural M.S. members and shall include 48 mm outside-diameter M.S. bracket arms, 60 mm outside-diameter central support pipe, 125 mm and 140 mm pole-shaft outside diameters at the locations shown in the approved drawing, and an approximately 410 mm diameter decorative base. All load-bearing members, wall thicknesses, welds, base plate, access opening and connections shall be designed for the applicable wind load and complete luminaire and logo load, supported by approved structural calculations and shop drawings. The pole shall include a weather-protected lockable service door, terminal plate, cable entry, earthing stud, minimum 3-core x 2.5 sq. mm FRLS copper internal wiring, IP65 terminal enclosure, 6 A double-pole MCB, surge-protection device, earthing conductor, cable glands, lugs and ferrules. The item shall include excavation and an approximately 1,000 mm x 1,000 mm x 2,000 mm deep RCC foundation, subject to soil conditions and approved design, with minimum M25 concrete, reinforcement as detailed, four Nos. 20 mm diameter x 900 mm long foundation bolts with template, base plate, levelling, non-shrink grouting, erection, plumbing, curing, backfilling and disposal of surplus material. All surfaces shall be cleaned and mechanically prepared and finished with epoxy primer, epoxy top coat, approved antique-finish coat and exterior-grade polyurethane protective lacquer coat in the approved colour. The complete pole shall be free from casting and fabrication defects and shall include weather-resistant fasteners, anti-corrosion treatment, structural stability and wind-load certificate and all labour, materials and accessories necessary for complete installation, as per the approved drawing, sample and final structural design. |
| 11 | Supply and Installation of Aluminum Die-cast LED Fixture Model RGL-01-L (Decorative Hanging Type)ParameterSpecificationWattage120 Watt Light Type White LED with C.T-2 LensLuminous Efficacy≥ 130 lm/WInput Voltage 230V AC ±10%, 50 HzPower Factor ≥ 0.95Driver Constant Current, Isolated, IP-65 RatedBody Material Pressure Die-Cast Aluminum with powder coated finishIngress Protection IP-65 (Weatherproof)Mounting600 mm MS Bracket Arm with nut boltsColor Temperature5700K ± 10%Operating Temp.-10°C to +50°CWarrantyMinimum 2 Years |
| 12 | Supply and Fixing of LED Decorative Lantern Type Fixtures mounted on both sides of top portion. ParameterSpecification Quantity 1 Nos. per poleWattage15-17 Watt eachBody MaterialCast Aluminum with Clear Acrylic CoverLED TypeWarm WhiteProtectionIP-65 (Outdoor Use)MountingDirectly fixed to MS decorative bracket with clampVoltage230V AC, 50 HzDriverBuilt-in constant currentFinishPowder coated black/golden antiqueWarranty 2 Years Focus Light For mudra,diva,vina |
| 13 | Providing, manufacturing and securely fixing one exterior-grade cast aluminium logo, maximum 750 mm x 750 mm, in the approved design - Type A (Veena and lotus), Type B (ceremonial lamp/diya) or Type C (Maharana Pratap message plaque) - with minimum 5 mm average finished thickness, concealed structural support, SS-304 fasteners, anti-corrosive primer, approved colour coating, UV-resistant PU protective coat and all accessories, complete as per approved sample and shop drawing |
| 14 | Add GST Charges 18% |
| 15 | Add 1% Insurance Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysOct 19, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender