Tender For Various Civil Repair & Maintenance Work I/C Construction Of Septic Tank For 4 No. E & F-Type Quarters At 400 Kv S/S Katni And 8 E-Type Quarters At 132 Kv S/S Katni
Tender Value
89.38 Lakhs
Estimated cost
Bid Submission
02 Nov 2026
16 days left
EMD
1.78 Lakhs
Bank guarantee accepted
Document Fee
2360
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Katni → Madhya Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Various Civil Repair & Maintenance Work I/C Construction Of Septic Tank For 4 No. E & F-Type Quarters At 400 Kv S/S Katni And 8 E-Type Quarters At 132 Kv S/S Katni
BOQ
| Sl. No. | Item Description |
| 1 | Various Civil Repair & Maintenance work i/c construction of septic tank for 4 no |
| 2 | 22.23,\\"Providing water proofing treatment over Roof, Wall, Chhajjas, Balcony with Rubberized elastomeric cold applied liquid waterproofing membrane blend of special resin and rubber with more than 1300% elongation (confirming ASTM-D2370-98), at leakage/seepage area consisting of the following operation. (i) Removal of damaged waterproofing treatment if any like bituminous membrane / plaster/ brick bat koba/screeding etc. .(ii) Surface preparation: Roughening of surface by scrubbing with steel wire/ Nylon brush/ Removing all dust particles and washing with adequate water to clean completely, opening of cracks in 'V' groove in size of 5mm x 10m (WxD), filling of cracks with elastomeric creak filler/PU sealent repair of potholes and holor making on roof surface by polymer mortar with adding SBR bonding agent. (iii) Providing and applying 1st coating of rubberized elastomeric liquid membrane as primer (ratio 1:2 1 part liquid membrane and 2 part water) by brush/ Roller/ Spray having minimum thickness of 70-80 micron. Allow the coating to set in natural air for minimum 2 hrs, then put reinforcement by laying 45gsm fibre glass mesh and applying 2nd coat of rubberized elastomeric liquid membrane .(Ratio: 1 part membrane and 20% water) with minimum thickness 100-120 micron. Allow the coating to set in natural air for minimum 12 hrs. (iv) Providing and applying 3rd coat of rubberized elastomeric liquid membrane .(Ratio: 1 part membrane and 10% water). Total DFT (Dry film thickness) thickness after 3rd coat must be 280-300 micron and consumption in three coats @ 6.5kg for 10sqm. (v) Providing and applying 4th and 5th coat .of High quality waterproof membrane in white colour, single component special synthetic resin based flexible thixotropic white color coating with excellent UV resistance (SRI - 144) with more than 300% elongation .(confirming ASTM D 412-98) in ratio: 1 part membrane and 10% water thickness of 200 micron DFT in two coats, with average consumption @ 5kg per 10 sqm. After application of fourth coat let it air dry for minimum 3 hrs before application of fifth coat. (vi) The treated area must be tested for water leakage/seepage by flooding with water for 48 .hrs (vi) Application of membrane coating shall be got done by authorized applicator of manufacturer. .(vii) 5 years of service guarantee to be provided. All above operations to be done in order as per direction on Engineer-in-Charge.\\" |
| 3 | 22.14.1 ,\\"Grading roof for receiving water proofing treatment with.Cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size)\\" |
| 4 | 14.64,Chipping, Removing, Carefully loose plaster and Concrete work by low impact Hammer, Breaker without damaging the structure as Instructed by Engineer-in-Charge. |
| 5 | 11.78.1.1,\\"Providing and laying vitrified floor tiles Multi/Double charged (Minimum top layer thickness 2.0mm) Neno Polished self design, in different size with water absorption less than0.05% and conforming to IS:15622 of approved make in all colours& shades, quality/ premium quality in flooring laid on 12mm thick cement mortar 1:4(1cement :4sand) including grouting the joints with white cement and matching pigments etc. complete..In light shade glossy/ rustic /stain finished..Size 600X600 mm thickness 9-10 mm.\\" |
| 6 | 11.79.1.1 ,\\"Providing and laying vitrified floor tiles Multi/Double charged (Minimum top layer thickness 2.0mm) Neno Polished self design, in different size with water absorption less than 0.05% and conforming to IS:15622 of approved make in all colours & shades, 1st quality/ premium quality in skirting, dado and wall lining laid on 12mm thick cement mortar 1:4(1cement :4sand) including grouting thejoints with white cement and matching pigments etc. complete..In light shade glossy/ rustic /stain finished..(a) Size 600X600 mm thickness 9-10 mm\\" |
| 7 | 11.49,Providing and laying Ceramic glazed floor tiles 300x300 mm or more (having thickness 6 to 7mm) of 1st quality conforming to IS : 15622 of approved make in any colours and shade laid on20 mm thick Cement Mortar 1:4 (1 Cement : 4 sand) including pointing the joints with white cement and matching pigment etc., complete. |
| 8 | 11.50, Providing and fixing Ceramic glazed wall tiles 300x450 mm or more (having thickness 6 to 7 mm) of 1st quality conforming to IS: 15622 of approved make in all Colours& shades, except burgundy, bottle green, black laid on 12mm thick bed of Cement Mortar 1:3 (1 Cement: 3 sand)preprad same day when mortar is still green jointed with grey cement slurry @3.3 kg per sqm including pointing the joints with white cement and matching pigments etc., complete. |
| 9 | 11.22.5, \\"Providing and fixing 18mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut for kitchen platforms, vanitycounters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to givehigh gloss finish wherever required etc. complete at all levels. Samples approved by Engineer-in- Charge...Cuddpah stone \\" |
| 10 | 11.22.1 ,\\"Providing and fixing 18mm thick gang saw cut mirror polished (premoulded and prepolished) machine cut for kitchen platforms, vanitycounters, window sills , facias and similar locations of required size of approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 sand) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing moulding and polishing to edge to givehigh gloss finish wherever required etc. complete at all levels. Samples approved by Engineer-in- Charge...Raj Nagar plain/White Marble/Udaipur Green Marble /Zebra black\\" |
| 11 | 9.170.3 ,\\"Providing and fixing factory made 30 mm thick PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for styles and 15x15mm for top and bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5mm thick heat moulded PVC 'C' channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45degree angle on both side forming styles; and 5mm thick, 95mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mmshall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10mm (5mmx2) thick, 20mm wide cross PVC sheet be provided as gap insert for top rail and bottom rail. paneling of 5mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles and rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' channel using PVC solven adhesive etc. complete as per direction of Engineer-in-charge. Manufacturer's specification and drawing...Pre laminated PVC door shutters. \\" |
| 12 | 15.48,Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 13 | 15.40.1,\\"Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the pipes manually/ by mechanical means including stacking of pipes within 50 metres lead as per direction of Engineer-in-Charge :..15 mm to 40 mm nominal bore\\" |
| 14 | 13.8,6 mm cement plaster of mix : 1:3 (1 cement : 3 sand) |
| 15 | 13.2.2 ,\\"15 mm cement plaster on the rough side of single or half brick wall of mix..1:6 (1 cement : 6 sand) \\" |
| 16 | 13.3.2 ,\\"20 mm cement plaster of mix :..1:6 (1 cement : 6 sand)\\" |
| 17 | 10.27.1,\\"Providing and fixing glass panes/ steel sheet/ fibre sheet with putty and glazing clips in steel doors, windows, clerestory windows all complete...With 4.0 mm thick glass panes \\" |
| 18 | 14.30, Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 19 | 13.41,Providing and applying white cement based putty of average thickness 1 mm, of approved brand over the plastered wall surface to prepare the surface even and smooth i/c all cost of material, labour and scaffold etc in all position complete. Note : Putty shall be applied only on the internal walls, for application on the exterior walls prior permission of Chief Engineer will be required. |
| 20 | 14.51.1,\\"Finishing walls with Acrylic Smooth exterior paint of required shade :..Old work (Two or more coat applied @ 1.67 ltr/ 10 sqm) on existing cement paint surface)..\\" |
| 21 | 13.46,Wall painting by any mechanical or manual means with plastic emulsion paint of approved brand and manufacture to give an even shade: Two or more coats on new work |
| 22 | 14.37,Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: One or more coats on old work. |
| 23 | 10.22.2,\\"Steel work welded in built up sections/ framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required...In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.\\" |
| 24 | 21.1.2.2 ,\\"Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved .make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, .including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) .:For shutters of doors, windows and ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required .including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for .separately)..Powder coated aluminium (minimum thickness of powder coating 50 micron) .\\" |
| 25 | 11.72.1,\\"Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc. of required colour strength, thickness pattern, surface texture (smooth/rough) and size/shape, conforming to 15658- 2006 made by table vibratory method using PU mould, laid in required colour and pattern over 50mm thick compacted bed of sand, compacting and proper embedding/ laying of inter locking paver blocks into the bedding layer through vibratory compaction byusing plate vibrator, filling the joints with sand and cutting of paver blocks as per required sizeand pattern, finishing and sweeping extra sand including locking with M15 cement concrete in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per manufacturer's specifications and direction of Engineer-in-Charge...80 mm thick C.C. paver block of M-35 grade.\\" |
| 26 | 9.46.2 ,\\"Providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.63 mm all complete...With 12 mm mild steel U beading.\\" |
| 27 | 18.28,WATER SUPPLY/INTERNAL SANITATION Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank |
| 28 | 18.6.1.3 ,\\"Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in-Charge...Internal work - Exposed on wall..25 mm nominal outer dia .Pipes..\\" |
| 29 | 18.6.2.1,\\"Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in-Charge..Concealed work including cutting chases and making good the walls etc...15 mm nominal outer dia .Pipes.\\" |
| 30 | 18.6.2.2 ,\\"Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in-Charge..Concealed work including cutting chases and making good the walls etc...20 mm nominal outer dia .Pipes..\\" |
| 31 | 17.14.2.2 ,\\"Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets and stainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required :..Kitchen sink without drain board..610x460 mm bowl depth 200 mm.\\" |
| 32 | 17.11.3 ,\\"Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :..White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps.\\" |
| 33 | 18.44.2,\\"Providing and fixing PTMT bib cock of approved quality and colour 15mm nominal bore..122 mm long weighing not less than 99 gm\\" |
| 34 | 17.58.2 ,\\"Providing and fixing unplasticised Rigid PVC soil and waste pipes conforming to IS: 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Single socketed pipes for working pressure of 4 kg/sqcm. (minimum wall thickness 3.2mm)..110 mm diameter\\" |
| 35 | 17.58.1,\\"Providing and fixing unplasticised Rigid PVC soil and waste pipes conforming to IS: 13592 Type B including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Single socketed pipes for working pressure of 4 kg/sqcm. (minimum wall thickness 3.2mm)..75 mm diameter\\" |
| 36 | 17.1.1,\\"Providing and fixing water closet squatting pan (Indian type W.C. pan) with 100mm sand cast Iron P or Strap, UPVC P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures completeincluding cutting and making good thewalls and floors wherever required :..White Vitreous china Orissa pattern W.C. pan of size 580x440mm with.integral type foot rests..\\" |
| 37 | 19.4.2 ,EXTERNAL SANITATION \\"Providing and laying below ground unplasticised PVC pipe to with stand working pressure of 4 kg/cm2 soild waste pipes confirming to IS:13592 and IS:4985 including jointing with seal ring confirming to IS :5282 leaving 10mm gap for thermal expansion all necessary fittings etc. complete. Excavation to be paid seperataly...160 mm diameter OD (min. wall thickness 4.0mm)\\" |
| 38 | 19.4.3 ,\\"Providing and laying below ground unplasticised PVC pipe to with stand working pressure of 4 kg/cm2 soild waste pipes confirming to IS:13592 and IS:4985 including jointing with seal ring confirming to IS :5282 leaving 10mm gap for thermal expansion all necessary fittings etc. complete. Excavation to be paid seperataly...200 mm diameter OD (min. wall thickness 4.9mm).\\" |
| 39 | 19.9.1.1 ,\\"Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 sand ) R.C.C. top slab with Cement Concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stone aggregate 20 mm nominal size), foundation concrete 1:2:4 mix (1 cement : 2 sand : 4 graded stoneaggregate 20mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design..Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions total weight of cover and frame to be notless than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :..With well burnt bricks.\\" |
| 40 | 2.6,SEPTIC TANK..Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5m in width as well as 10 sqm on plan) including dressing of sides and ramming of bottom disposal of excavated earth, lead up to 50m and lift up to 1.5m, disposed earth to be levelled and neatly dressed. (No extra lift is payable if work is done by mechanical means) All kinds of soil |
| 41 | 4.1.2.3 ,\\"Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level :..With 40mm nominal size graded stone aggregate..M-7.5 Nominal Mix -1 Cement : 4 sand : 8 graded stone aggregate....\\" |
| 42 | 5.16.6,\\"Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding including cost of binding wire all wastages and overlaps, couplers (overlaps shall be provided as per requirement of IS 13920 for ductile detalingIS 456 RCC Design & SP 34 Reinforcement detailing ) etc. complete . (Note:- 1. Spacer bars (chairs) shall be paid separately as shown in the drawing and as per direction of engineer in charge. 2. No extra payment shall be done for overlaps and/or couplers. 3.Couplers shall be conforming to IS code on \\"Reinforcement Couplers for Mechanical Splices of Bars for Concrete Reinforcement - Specification\\")..Thermo-Mechanically Treated bars.FE 500 D or more conforming to IS 1786..\\" |
| 43 | 5.9.2.1 ,\\"Centering and shuttering in cluding strutting, propping etc. and removal of form for:..Walls (any thickness) in cluding attached pilasters butter esses, plinth beams and string courses etc...Uptoplinthlevel\\" |
| 44 | 5.1.1,\\"Providing and laying in position specified grade of reinforced cement concrete (nominal / design mix with 20mm nominal size graded stone aggregate) excluding the cost of centering,shuttering, finishing and reinforcement -All work up to plinth level :..M-20 Grade Concrete\\" |
| 45 | 2.24,Filling available excavated earth (excluding hard rock/Ordinary rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. |
| 46 | 18.7.6 ,\\"Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipe and fittings with onestep CPVC solvent cement, trenching, refilling andtesting of joints complete as per direction of Engineer-in- Charge..External Work..50 mm nominal outer dia .Pipes.\\" |
| 47 | 18.12.2.4 ,\\"Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :...With brass lever handle of approved quality...50 mm nominal bore\\" |
| 48 | 4.3.1.2 ,ELECTRIFICATION.\\"Wiring for circuit wiring with PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) of ISI marked suitable size etc. as required as per specification.2x2.5 Sq.mm. ..Using modular accessories\\" |
| 49 | 4.3.2.2 ,\\"Wiring for circuit wiring with PVC insulated cable FRLS with copper multi strand conductor ISI marked in concealed rigid P.V.C. conduit (HMS) of ISI marked suitable size etc. as required as per specification.4x2.5 Sq.mm...Using modular accessories\\" |
| 50 | 3.1.1.1.2,\\"Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. conduit (MMS) ISI marked of suitable size and 1.5sq. mm. PVC FRLS insulated copper earth continuity conductor of green colour inside conduit etc. as required as per specification for :-..Light point/fan points..Primary short point.Using modular accessories.\\" |
| 51 | 3.1.1.2.2 (SOR w.e.f. 01.01.2024)Electri,\\"Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. conduit (MMS) ISI marked of suitable size and 1.5sq. mm. PVC FRLS insulated copper earth continuity conductor of green colour inside conduit etc. as required as per specification for :-..Light point/fan points..Primary medium point .Using modular accessories.\\" |
| 52 | 3.1.1.3.2,\\"Point wiring (excluding metallic switch box & sheet but including switches, sockets, lamp holders/ceiling roses etc) with 1.5sq. mm. PVC insulated cable FRLS with copper multi strand conductor ISI marked in surface rigid P.V.C. conduit (MMS) ISI marked of suitable size and 1.5sq. mm. PVC FRLS insulated copper earth continuity conductor of green colour inside conduit etc. as required as per specification for :-..Light point/fan points..Primary long point.Using modular accessories.\\" |
| 53 | 27.8.1.2,\\"Supply of ISI marked and accepted standard of miniature circuit breaker (MCB) of 'C' series with short circuit indication, suitable for 240/415 Volts,50 Cycle, 10 kA/15 kA Value AC supply conforming to IS : 8828 : 1996, IEC : 60898 :2002 & 60947-2 but without enclosures :-..single Pole..MCB SP 6Amp to 32Amp 10kA rating\\" |
| 54 | 64 NSOR,Providing & Fixing earthing arrangement with 600x600x3.15 mm copper plate electrode including packing of charcoal powder and salt as per specification,water pipe 19 mm dia G.I.connections, etc. complete with excavation & refilling the pit with material as required, etc. with cost of all material, labour, T&P, taxes, transportation etc. complete as per direction of Engineer in charge. |
| 55 | 9.5.2.2,Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws excluding, panelling/glazing which will be paid for separately, all complete as per direction of Engineer-in-charge...Second class teak wood..30 mm thick shutters . |
| 56 | 9.6.2,Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick:..Kiln seasoned and chemically treated Haldu, Kail, Bija wood Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysNov 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender