Tender For Provn Of Fountain And Improvement Of Operation Readiness Room At Both Runway End At Af Stn Bihta.
Tender Value
18.40 Lakhs
Estimated cost
Bid Submission
30 Oct 2026
14 days left
EMD
36800
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Patna → Bihar
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Fountain And Improvement Of Operation Readiness Room At Both Runway End At Af Stn Bihta.
BOQ
| Sl. No. | Item Description |
| 1 | Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in soft/loose soil & spreading in surrounding area n exc 50 m distance complete, all as specified. |
| 2 | Excavation in trenches n. exc 1.5 m wide for foundations not exceeding 1.5 m deep and getting out in SOFT/LOOSE soil complete, all as specified. |
| 3 | Returning filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick complete, all as specified. |
| 4 | Removal of excavated surplus spoil to a distance n. exc. 50m and depositing where directed at level not exceeding 1.5 m above the starting point complete all as specified. |
| 5 | PCC type B-0 (1:2:4), using (12.5 mm graded stone aggregates) as in roof padding, kerbs, or mud stops, rounded or chamfered on edge , complete all as specified. |
| 6 | PCC type D-2 (1:4:8), using (40 mm graded stone aggregates) as in foundation, complete all as specified. |
| 7 | Reinforced cement concrete, type B-1,(1:2:4), (nominal mix) using 20 mm graded stone aggregates, as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified. |
| 8 | Reinforced cement concrete, type B-1,(1:2:4), (nominal mix) using 20 mm graded stone aggregates, as in columns, pillars / post & struts complete all as specified. |
| 9 | Reinforced cement concrete, type B-1,(1:2:4), (nominal mix) using 20 mm graded stone aggregates, as in as in lintels over 1.5 metre clear span, cills, steps, seismic and other similar band, plinth courses, lacing courses , copings, kneelers, apex stones, bed plates, water troughs and the like complete all as specified. |
| 10 | Use & waste of formwork to sides of square or retangular pillars any type, posts, struts, piers, columns and stanchions with rough finished surfaces of concrete, complete all as specified. |
| 11 | Use & waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter with rough finished surfaces of concrete, complete all as specified. |
| 12 | Wall water fall fountain of size 12 feet x 8 feet with 2.5 feet with 2.5 feet tank, light as required and water sheet including motor of 1.00 HP including back wall teal wood stone and black granite, Buddha (sand stone brown) of height 3 feet complete all as specified. |
| 13 | Brick work using bricks as specified in PS clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:6), complete all as specified. |
| 14 | Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, thickness 35 mm,etc complete all all as specified. |
| 15 | Aluminium anodised barrel tower bolt of extruded section 200mm long, ISI marked, complete all as specified. |
| 16 | Aluminium alloy, anodised, ISI marked sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy 300 mm long, complete all as specified. |
| 17 | Extruded aluminium anodised handles fabricated type with plate 150 mm long, ISI marked complete all as specified. |
| 18 | Double leg aluminium anodised door stopper with rubber foot, ISI marked and fixed to bottom rail of doors with steel screws, complete. |
| 19 | Mild steel ordinary rat tail rod pattern helical door spring 300mm long including roller and roller plate, complete all as specified |
| 20 | Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with tinned tacks or steel wire staples all as specified. |
| 21 | Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified. |
| 22 | Mild steel TMT bars 5 mm and over up to and including 10 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips in stirrups, spacers and binders complete all as specified. |
| 23 | Mild steel rolled sections as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to grade Fe-410-W Gde E-250, complete all as specified. |
| 24 | Framed mild steel work such as grills, grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, railings and similar work confirming to Fe-290-Gde E-165, complete all as specified. |
| 25 | Factory made 35 mm thick ,2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass,gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass,etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a);,etc complete all all as specified. |
| 26 | Powder coated aluminium (minimum thickness of coating 50 micron) frame of OG colour window and ventilator frame having three sliding shutter on roller etc (02x glazed shutter and 01 x gauged shuttter) with glazing clip, rubber packing, anodised aluminium snap beading, screws, locks etc complete all all as specified.NOTE- Wiremesh & glass will be measured and paid for separately under respective item of BoQ.) |
| 27 | Powder coated aluminium (minimum thickness of coating 50 micron) frame of OG colour any colour as approved by GE for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc complete all all as specified. |
| 28 | Pressed steel frames of size 125 mm x 60 mm made out mild steel 1.25 mm thick, for doors with one or more rebates including necessary fixing lugs, 100 mm size medium grade mild steel hinges, lock strike plates etc including providing PCC (1:3 :6) type C-0 using 12.5 mm graded crush stone aggregate for filling back of chowkhats complete all as specified. |
| 29 | 6mm thick plan solid acrylic sheet of any colour fixed with aluminium strip with rubber beading 4-5cm wide over frame structure with stainless screw / rustless screw comlete all as specified. |
| 30 | 6mm thick plan solid acrylic sheet of any colour fixed with aluminium strip with rubber beading 4-5cm wide over frame structure with stainless screw / rustless screw as in ridge comlete all as specified. |
| 31 | Powder coated GI snap grid frame work of size 605mm x 605mm for false ceiling complete with acessories all as specified and shown on serial page No.186 of MES Schedule Part-II. |
| 32 | Hangers 3-6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs / trusses by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified. |
| 33 | 4-6 mm thick E-board, multipurpose, decorative type fixed in grid frme work ceilings as panels, complete all as specified. |
| 34 | 25 mm thick, cement concrete type B-0, 1:2:4 using 12.5 mm graded stone aggregate, finished rough, as in sub floors or similar locations, complete all as specified. |
| 35 | 100 mm thick PCC type D-2 (1:4:8), using 40 mm graded stone aggregates as in finished even & rough, as in sub floors, complete all as specified. |
| 36 | 75 mm thick, cement concrete type C-1, 1:3:6 using 20 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection, and joints shall be sealed with joint sealing comound grade 'B' complete all as specified. |
| 37 | Non skid ceramic coloured pattern tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.18 Sq.m but n. exc. 0.36 Sq.m, laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:6), complete all as specified. |
| 38 | Non skid ceramic coloured pattern tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.18 Sq.m but n. exc. 0.36 Sq.m, on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile laid over and including 10mm thick rendering in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified |
| 39 | Factory made PCC chequered tiles, glossy finish, ISI Marked, with grey cement & pigment, 22-25 mm thick, of size 300 mm x 300 mm, in floors, over & including 20 mm thick cement mortar (1:4) screed, set and jointed with grey cement slurry complete, all as specified. |
| 40 | Rendering 5 mm thick on fair faces of concrete surfaces, finished even and smooth on ceiling in cement mortar (1:3), complete all as specified. |
| 41 | Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:6), complete all as specified. |
| 42 | Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair using water proofing compound on walls in cement mortar (1:4), complete all as specified.NOTE: Supply only WPC will be measured & paid for separately under respective item of BoQ. |
| 43 | Supply only liqiud water proofing compound, ISI marked, complete all as specified. |
| 44 | Three coats of white washing on new undecorated ceiling surfaces, including preparation of surfaces, complete all as specified. |
| 45 | Two coats of white wash on old ceiling surfaces, including preparation of surfaces, complete all as specified. |
| 46 | Complete removal of existing treatment of any description, including prepration of wall surfaces of any description complete all as specified and applying the following: -(a) Applying wall care putty, in two layer & smoothening the surfaces etc. as specified (preparatory to paint as directed). (b) Two coats of interior acrylic distemper over and including a coat of acrylic emulsion primer. |
| 47 | Prepration of new plasterd wall surfaces of any description complete all as specified and applying the following: -(a) Applying wall care putty, in two layer & smoothening the surfaces etc. as specified (preparatory to paint as directed). (b) Two coats of interior acrylic distemper over and including a coat of acrylic emulsion primer. |
| 48 | Complete removal of existing treatment with mechenical scraper of any description, applying Two coats of exterior acrylic emulson over and including a coat of water based exterior primer & including prepration of wall surfaces of any description in disruptive/camouflaging pattern of four / three shades complete all specified |
| 49 | Prepration of new plasterd wall surfaces of any description & applying Two coats of exterior acrylic emulsion over and including a coat of water based exterior primer in disruptive/camouflaging pattern of four / three shades complete all specified |
| 50 | Sheet glass 4 mm thick ordinary quality and glazing with oil putty or wooden beads in squares n. exc. 0.5sqm in each pane complete all as specified. |
| 51 | Two coats of synthetic enamel paint over & including a coat of pink primer over wood and wood (new) based surfaces of any description not other wise described over 10cm width or girth including preparation of surfaces complete all as specified. |
| 52 | Two coats of synthetic enamel paint over & including a coat of red oxide primer over steel & iron (new) surfaces of any description, not otherwise described, over 10 cm in width or girth, including preparation of surfaces complete all as specified. |
| 53 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sq.m each and removing from site all as specified. |
| 54 | Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 Sq.m but not exceeding 4.00 Sq.m each and removing from site all as specified. |
| 55 | Taking down cement plaster of any description on brick walls or concrete surfaces etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified. |
| 56 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified. |
| 57 | Demolition of cement concrete (unreinforced) in ground floors and pavings not excceding 15cm thickness (above or below ground level) all as specified |
| 58 | Demolition brickwork or stone / boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified. |
| 59 | Dismantling wall and ceiling boards (fibre, pulp, gypsum, POP, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified. |
| 60 | Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified. |
| 61 | Dismantling wrought iron or mild steel work of any description, complete all as specified. |
| 62 | Note : Amount of credit for retrieved materials is mentioned in Sch of credit of tender documents in pdf form which will be deducted while acceptance of tender offline. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 30, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 14 daysOct 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 15 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender