Tender For Providing And Fixing Open Air Gym For Two Locations At Nand Gram Panchayat Under Murpar Sub Area Of Umrer Area.
Tender Value
13.14 Lakhs
Estimated cost
Bid Submission
21 Oct 2026
9 days left
EMD
16500
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Nagpur → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Providing And Fixing Open Air Gym For Two Locations At Nand Gram Panchayat Under Murpar Sub Area Of Umrer Area.
BOQ
| Sl. No. | Item Description |
| 1 | Item Description/ Heading |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. All kinds of soil |
| 3 | Supplying and stacking at site Aggregates 63mm- 45mm including all leads complete. |
| 4 | Supplying and stacking at site close graded granular sub base material 26.5mm- 9.5mm including all leads complete. |
| 5 | Spreading hard murum/ soft murrum/ gravel or kankar for side width complete |
| 6 | Compacting thehardmurumsidewidths including laying in layersoneachsidewith vibratory roller including artificial watering etc. complete. |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 8 | Providing and laying 60mm thick factory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design& shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge |
| 9 | Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete. |
| 10 | Providing and fixing of retro- reflectorised informatory sign board rectangular/Square in shape having area less than 0.9 One Square Meterr made out of ____mm aluminum sheet bonded with white retro reflective sheeting of Class __ ( Type IV High intensity microprismatic grade sheeting-HIP) having pressure sensitive/heat activated adhesive retoreflective specified back ground, border and back side retoreflctive symbols, letters, numerals, arrow as per IRC:67-2012 Table No 8.3, supported with back support frame 25mm x 25mm x 3mm, duly painted on back side with two coats of grey stove enamel paint and supported on one no. mild steel angle iron post 75 mm x 75 mm x 6 mm, 3.5 mt long firmly fixed to the ground by means of properly designed foundation with M25 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing The angle iron post shall be duly painted with one coat of epoxy primer and two coats of epoxy finish paints having alternate black and white bands of 25 cm width including GI fixures and transportation etc.complete.The nut bolts of board with angle iron post/supporting structure after fixing at site has to be electrically welded. Class B ( Type IV High intensity micro-prismatic grade sheeting-HIP) sheeting shall have 7 years written warranty from the manufacturer and authorised distributor/convertor issued for field performance including the screen printed areas and cut-out sheeting and cut-out durable transparent overlay film and this warranty certificate in original should be submitted to the Engineer in charge by the contractor/supplier. 2mm aluminum sheet Class B |
| 11 | Supply and Fixing SINGLE AIR WALKER PFGE- 01 PRODUCT AREA :-L x W x H 1065mm x 785mm x 1390mm. SAFE PLAY AREA:- 1524mm x 1024mm. Air Walker equipment made up of 3inch “B” class MS pipe; Prime Stand duly bend, Foundation center pipe. The pedal frame is made of 42mm OD MS pipe. The handle frame is made of 32mm OD MS pipe. Footrest frame support of dimension 250 x 100 x 2mm is welded for supporting the Aluminium footrest. Aluminium Footrest of size 300mm x 150mm x 5mm is used for supporting the foot. ϕ 60mm seamless pipe bushes. Permanent lubricated Ball bearings 6205zz/6205-2rs. Foundation plate of dia ϕ175mm and 10 mm thickness is welded at bottom. All welded joint are of good quality. High tensile steel with galvanized nut & bolts to be used. The Circlips to be used are of 25mm. Allen Bolts are also used to tighten the closing cap. Closing cap of HDPE / PPCP Plastic is used. PU PAINT |
| 12 | Supply and Fixing SURF BOARD PFGE- 03 PRODUCT AREA :-L x W x H 915mm x 762mm x 1372mm. SAFE PLAY AREA:- 1524mm x 1220mm. Surf Board equipment made up of 3 inch “B” class MS pipe; Prime Stand duly bend, Foundation center pipe. The pedal frame is made of 42mm OD MS pipe. The handle frame is made of 32mm OD MS pipe. Footrest frame support of dimension 250 x 150 x 5mm is welded for supporting the seat. MS seat of size 380mm x 300mm x 5mm is used for supporting the foot pipe. ϕ 60mm seamless pipe bushes. Permanent lubricated Ball bearings 6205zz/6205-2rs. Foundation plate of dia ϕ225mm and 10 mm thickness is welded at bottom. All welded joint are of good quality. High tensile steel with galvanized nut & bolts to be used. The Circlips to be used are of 25mm. Allen Bolts are also used to tighten the closing cap. Closing cap of HDPE / PPCP Plastic is used. PU PAINT |
| 13 | Supply and Fixing SINGLE CHEST PRESSER PFGE- 08 PRODUCT AREA :-L x W x H920mm x 762mm x 2134mm SAFE PLAY AREA:- 1372mm x 1220mm• Double Chest Presser equipment made up of 4inch “B” class MS pipe; Prime Stand duly bend, Foundation center pipe.• The handle frame is made of 42mm OD MS pipe.• The remaining frame is made of 32mm OD MS pipe.• Seating frame support of dimension 250 x 150 x 5mm is welded for supporting the pedal seat.• MS Seat of size 380mm x 300mm x 5mm is used for supporting the foot.• ϕ 60mm seamless pipe bushes.• Permanent lubricated Ball bearings 6205zz/6205-2rs.• Foundation plate of dia ϕ225mm and 10mm thickness is welded at bottom.• All welded joint are of good quality.• High quality rubber grip are also used for firm handling.• High tensile steel with galvanized nut & bolts to be used.• The Circlips to be used are of 25mm.• Allen Bolts are also used to tighten the closing cap.• Closing cap of HDPE / PPCP Plastic is used. • PU PAINT |
| 14 | Supply and Fixing DOUBLE WHEEL SHOULDER BUILDER PFGE-12 PRODUCT AREA :-L x W x H1220mm x 762mm x 1676mm SAFE PLAY AREA:- 1828mm x 1220mm• Double Wheel Shoulder Builder equipment made up of 3inch“B” class MS pipe; Prime Stand duly bend, Foundation center pipe.• The wheel frame is made of 42mm OD MS pipe and the supporting is made of 32mm OD MS pipe.• ϕ 60mm seamless pipe bushes.• Permanent lubricated Ball bearings 6205zz/6205-2rs.• Foundation plate of dia ϕ175mm and 10mm thickness is welded at bottom.• All welded joint are of good quality.• High tensile steel with galvanized nut & bolts to be used.• The Circlips to be used are of 25mm.• Allen Bolts are also used to tighten the closing cap.• Closing cap of HDPE / PPCP Plastic is used. • PU PAINT |
| 15 | Supply and Fixing LEG PRESS PFGE- 17 PRODUCT AREA :- L x W x H1676mm x 610mm x 1524mm SAFE PLAY AREA:- 2286mm x 1220mm• Leg Press equipment made up of 4inch “B” class MS pipe; Prime Stand duly bend, Foundation center pipe.• The remaining frame is made of 42mm OD MS pipe.• MS Seat of size 380mm x 300mm x 5mm is used.• ϕ 60mm seamless pipe bushes.• Permanent lubricated Ball bearings 6205zz/6205-2rs.• Foundation plate of dia ϕ225mm and 10mm thickness is welded at bottom.• All welded joint are of good quality.• High quality rubber grip are also used for firm handling.• High tensile steel with galvanized nut & bolts to be used.• The Circlips to be used are of 25mm.• Allen Bolts are also used to tighten the closing cap.• Closing cap of HDPE / PPCP Plastic is used. • PU PAINT |
| 16 | Supply and Fixing SKY WALKER/STRAIGHT TRAINER/ DBL AIR WALKER HAND MOVEMENT PFGE- 21 PRODUCT AREA :-L x W x H1778mm x 610mm x 1828mmSAFE PLAY AREA:- 2134mm x 915mm• Straight Trainer/Sky Walker equipment made up of 4inch “B” class MS pipe; Prime Stand duly bend, Foundation center pipe.• The pedal frame is made of 3\\" x 1\\" rectangular MS pipe.• The handle frame is made of 32mm OD MS pipe.• Footrest frame support of dimension 250 x 100 x 2mm is welded for supporting the Aluminium footrest.•Aluminium Footrest of size 300mm x 150mm x 5mm is used for supporting the foot.• ϕ 60mm seamless pipe bushes.• Permanent lubricated Ball bearings 6205zz/6205-2rs.• Foundation plate of dia ϕ225mm and 10mm thickness is welded at bottom.• All welded joint are of good quality.• High tensile steel with galvanized nut & bolts to be used.• The Circlips to be used are of 25mm.• Allen Bolts are also used to tighten the closing cap.• Closing cap of HDPE / PPCP Plastic is used. • High quality rubber grip are also used for firm handling.• PU PAINT |
| 17 | Supply and Fixing ARM & PADDLE BIKE PFGE-28 PRODUCT AREA :-L x W x H1220mm x 610mm x 1067mmSAFE PLAY AREA:- 1829mm x 1220mm• Arm & Paddle Bike equipment made up of 2inch “B” class MS pipe; Prime Stand duly bend, Foundation center pipe.• The remaining frame is made of 42mm OD MS pipe.• MS Seat of size 380mm x 300mm x 5mm is used for seating arrangement.• ϕ 60mm seamless pipe bushes.• Permanent lubricated Ball bearings 6205zz/6205-2rs.• Foundation plate of dia ϕ200mm and 8mm thickness is welded at bottom.• All welded joint are of good quality.• High quality rubber grip are also used for firm handling.• High tensile steel with galvanized nut & bolts to be used.• The Circlips to be used are of 25mm.• Allen Bolts are also used to tighten the closing cap.• Closing cap of HDPE / PPCP Plastic is used. • PU PAINT |
| 18 | Supply and Fixing ROWER PFGE-30 PRODUCT AREA :-L x W x H1372mm x 762mm x 915mmSAFE PLAY AREA:- 1829mm x 1220mm• Rower equipment made up of 3inch “B” class MS pipe; Prime Stand duly bend, Foundation center pipe.• The seating frame is made of 3\\" x 1\\" MS pipe.• The remaining frame is made of 42mm OD MS pipe.• The handle frame is made of 32mm OD MS pipe.• MS Seat of size 380mm x 300mm x 5mm is used for seating arrangement.• The pins used are made up of Ø25mm hardened bright bar.• Permanent lubricated Ball bearings 6205zz/6205-2rs.• Foundation plate of dia ϕ200mm and 10mm thickness is welded at bottom.• All welded joint are of good quality.• High quality rubber grip are also used for firm handling.• The bushes (Stopper) used to avoid the collision.• High tensile steel with galvanized nut & bolts to be used.• The Circlips to be used are of 25mm.• Allen Bolts are also used to tighten the closing cap.• Closing cap of HDPE / PPCP Plastic is used. • PU PAINT |
| 19 | Total impact of GST for the purpose of CTC Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 09, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 9 daysOct 22, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 10 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender