Tender For Repairs To Roof Water Proof Treatment, Sunken Floors, Walls, Chajjas, Plaster, Plinth Protection And Other Misc Works For Otm & Md Accn Of Inspection Organisation, Aundh Under Ge (Mh & Rh) Khadki
Tender Value
Ref. Documents
Estimated cost
Bid Submission
29 Oct 2026
18 days left
EMD
40000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Pune → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repairs To Roof Water Proof Treatment, Sunken Floors, Walls, Chajjas, Plaster, Plinth Protection And Other Misc Works For Otm & Md Accn Of Inspection Organisation, Aundh Under Ge (Mh & Rh) Khadki
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete unreinforced of any description and in any position, not otherwise specifically provided for complete all as specified and directed. |
| 2 | M & L for 40 mm thick cement concrete 1:2:4 type B-0, using 12.5mm graded stone aggregates for filleting, benching, slightly rounding or chamfering on edges, filling undulations / depressions in roof surface, providing concrete platform for tanks wherever required as directed. |
| 3 | Taking down / removing existing water proofing treatment from RCC roof slab including removal of plaster bed below felt / membrane and disposal of the same to distance exceeding 50m but not exceeding 100m as and where directed and M & L for 10 mm thick screeding / rendering in cement mortar 1:4 on concrete roof surface, using Water Proofing Compound @ 3% by weight of cement, surface finished even and smooth without using extra cement all as directed.Note: Water Proofing Compound shall be measured and paid separately. |
| 4 | Supply only intergral water proofing compound. |
| 5 | M & L for cleaning the plastered /concrete surface with wire brush and applying water proofing treatment as under:-(a) Apply one coat of water based bituminious primer @ 0.20 Kg per Sqm.(b) Laying APP polimerised modified membrane weighing not less than 3.5Kg / sqm by torch application method. (thickness of membrane shall not be less than 3 mm). (c) The overlap for APP membrane shall be 75 mm on longitudinal direction and100 mm on transverse direction.(d) Finally applying a coat of solar reflective bituminious aluminium paint @0.15 Kg/Sqm over the membrane. |
| 6 | Disconnecting existing tanks exc 250 & not exc 500, setting asides (or lowering if required) for repairs, cleaning, waterproofing etc and hoisting if required reconnecting and re-fixing in position. |
| 7 | Disconnecting existing tanks exc 500 & not exc 1000, setting asides (or lowering if required) for repairs, cleaning, waterproofing etc and hoisting if required reconnecting and re-fixing in position. |
| 8 | Cleaning the surface with wire brush, detecting sources of leakages and removing/taking down unsound treatment/surface and M&L for carrying out non-destructive waterproofing treatment to sunken portion of slab, floor and walls of bath, WC, WHB and floor traps (combined unit) by using construction chemical method as hydrophobic PU grouting, etc, with first course of injection MDI based PU foam and second course of injection PU plain all as per manufacturers instruction, etc, complete and as directed. The PU foam shall have 100% solids and solvent free, and shall expand 30-40 times its volume at liquid stage in presence of water, the PU plain injection shall have minimum 100 CPS viscosity and shore hardness minimum 50. Make: PIDILITE or equivalent |
| 9 | Making hole and M&L for fixing thr metallic packer for hydrophobic PU foam and Sealer as per manufacturers specification. The PU foam shall have 100% solids and solvent free, and shall expand 30-40 times its volume at liquid stage in presence of water, the PU plain injection shall have minimum 100 CPS viscosity and shore hardness minimum 50. Make: PIDILITE or equivalent |
| 10 | M&L for the tile joint chemical cleaning and re-grouting carefully by washing the existing tille with heavy duty tile cleaner preferbly of M/S Pidilite or equivalent cleaner, again washing with fresh jet water, scratching the joints and filling the same with (white/matching colour) epoxy tile grout of M/s Pidilite, ROFF RTM epoxy or equivalent, or equivalent , curing , cleaning the surface etc, complete all as directed by Engr-in-Charge and as per the sample done at ground level. |
| 11 | M&L for water proofing treatment of External walls, chhajjas DFT: 110 microns by applying two coats of elestromeric coating Raincoat, material covering capabity 3 Sqm per litre in 2 Coats without dilution & 1 coat of efflorescent resistant primer 10sqm/litre/coat after cleaning the surface throughly and sealing all cracks with acrylic sealing compound as per the manufacturers specifications and directions of Engr-in-Charge Make :- Raincoat shall be of PlDlLlTE or equivalent. The product shall have following properties: Elongation > 100% as per ASTM D 412, Tensile strength : 2.5 Mpa as per ASTM D 412, Water Resistance conforming to SS 500, Crack bridging ability conforming to Class A4 as per EN 1062 Part 7, Positive hydrostatic pressure > 7 bar as per DIN 1048, Anti-carbonation property complying EN 1062 Part 6, RCPT conforming to ASTM C 1202. |
| 12 | M&L for providing water proofing plaster at the junction of wall and slab at chajjas, lintels etc, of average thickness 20mm in CM (1:3) with WPC, finished even and smooth without using extra cement all as specified and directed |
| 13 | Taking down cement plaster in any description incl racking out joints hacking for key and scrubbing down with water etc. Spd and directed by EIC |
| 14 | M&L for rendering 15 mm thick factory-made, polymer-modified, ready-mix cement plaster consisting of Ordinary Portland Cement conforming to IS 269/IS 8112/IS 12269, well-graded washed silica sand conforming to IS 2116, and performance-enhancing additives/plasticizers. The material shall be factory batched under quality-controlled conditions and supplied in sealed moisture-proof bags. The plaster shall be mixed only with the quantity of clean potable water recommended by the manufacturer using a mechanical mixer and applied over properly prepared, cleaned, wetted and hacked masonry/RCC surfaces. The plaster shall be applied in a single coat of 15 mm thickness on wall surfaces, properly ruled, leveled, floated and finished smooth using a steel trowel. The surface shall be free from cracks, hollowness, waviness, segregation, pinholes and other visible defects complete all as specified and directed by Engr-in-Charge. |
| 15 | M & L for PCC 1:3:6 type C1 (uisng 20mm graded aggregate) 75 mm thick as in Plinth, Path, floor with fair finish surface with out using extra cement all as spd. |
| 16 | Taking up or down steel tubing of 15 mm bore and connections, including cleaning for re-fixing or removal to store |
| 17 | Taking up or down steel tubing of 20 mm bore and connections, including cleaning for re-fixing or removal to store |
| 18 | S&F steel tubes of size 15mm bore (medium grade) galvanised with all fittingsand fixed complete to wall all as specified & directed by Engineer-in-charge. |
| 19 | S&F steel tubes of size 20 mm bore (medium grade) galvanised with all fittingsand fixed complete to wall all as specified & directed by Engineer-in-charge. |
| 20 | Fixing only steel tubes of size 15mm bore (medium grade) galvanised with all fittingsand fixed complete to wall all as specified & directed by Engineer-in-charge. |
| 21 | Fixing only steel tubes of size 20 mm bore (medium grade) galvanised with all fittingsand fixed complete to wall all as specified & directed by Engineer-in-charge. |
| 22 | M&L for cement concrete type D-2, 1:4:8 (40mm graded aggregate) 75 mm thick sub base or similar items all as specified and directed. |
| 23 | M&L fo Sand filling under floors or in foundation including watering and consolidation |
| 24 | M&L for 80mm thick coloured rubburised, glossy finish machine pressed interlocking pattern paver block any shape and size conforming to IS 15658-2006 of M-40 Grade incl all as specified and directed by Engineer-in Charge. |
| 25 | S&F Pre Polished Chequered cement concrete tiles glossy and rubburised finish 30cm x 30cm x 25mm thick, set, jointed and pointed in near cement slurry in floors including 15mm thick screed bed in CM 1:6 under tiles incl all as specified and directed by Engineer-in Charge. |
| 26 | Dismantling of old stone slab of any description. |
| 27 | M&L machine cut kota stone slab flooring 20-25mm thick in flooring but one piece as in treads of straircase etc over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete, over 15 mm thick screed bed or bedding in CM 1:6 for laying floor finishes, all as specified and directed. |
| 28 | All as item No 27 here in before but in skirting but one piece for step riser over and incl 10 mm thick rendering in CM 1:4 to receive kota stone/slab etc all as specified and directed. |
| 29 | Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations. |
| 30 | Demolition of Brickwork or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles |
| 31 | M&L for precast cement concrete, type C-1, 1:3:6 (20mm graded aggregate) masonary with solid blocks, exc , 10cm in width and setting in cement mortar (1:6) complete all as specified and directed. |
| 32 | M & L for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick work or concrete surfaces including finishing the surface with a thin layer of sagol all as specified and directed. |
| 33 | M & L preperation of old/ new plastered surfaces & applying two coats of oil bound distember over a coat of alkali resistant primer. |
| 34 | Taking down drain pipes (any size or pattern), including all fittings, T, bends,etc., including cleaning for refixing (measured overall as fixed along the centre line over fitting and accessories) |
| 35 | S&F PVC (SWR) pipes 110 mm dia single sockets, in any length rubber ring joints, laid in trenches or in floor all as specified and directed. |
| 36 | S&F PVC (SWR) pipes 75 mm dia single sockets, in any length rubber ring joints, laid in trenches or in floor all as specified and directed. |
| 37 | S&F PVC (SWR) 110mm dia bends any radius all as specified and directed. |
| 38 | S&F PVC (SWR) branch 110mm bore pieces, single ( single Y ) equal or unequal all as specified and directed. |
| 39 | S&F PVC (SWR) junction110mm bore single ( single t) equal or unequal all as specified and directed. |
| 40 | S&F PVC (SWR) 75 mm dia bends any radius all as specified and directed. |
| 41 | S&F PVC (SWR) junction 75 mm bore single ( single t) equal or unequal all as specified and directed. |
| 42 | S&F PVC (SWR) branch75 mm bore pieces, single ( single Y ) equal or unequal all as specified and directed. |
| 43 | M & L applying two coats of cement base paint to old/newly plastered surface of wall including preparation. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysOct 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender