Tender For Repair / Maintenance Of Sanitary Fittings Sewerage Pipe, Leakage, Seepage Of Bldg And External Plaster At Old Navy Nagar Under Age B/R-I (Nw) Navy Nagar Of Ge (Nw) Navy Nagar, Colaba, Mumbai
Tender Value
45 Lakhs
Estimated cost
Bid Submission
28 Oct 2026
6 days left
EMD
90000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Mumbai → Maharashtra
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair / Maintenance Of Sanitary Fittings Sewerage Pipe, Leakage, Seepage Of Bldg And External Plaster At Old Navy Nagar Under Age B/R-I (Nw) Navy Nagar Of Ge (Nw) Navy Nagar, Colaba, Mumbai
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) in ground floors and pavings nexc 15 cm thickness (below or above ground level) & removing debris out of MoD land at any distance complete all as specified. |
| 2 | M&L for cement concrete 1:5:10 type E2 using 40mm graded stone coarse aggregate in sunken floor complete all as specified and directed by Engr-in-Charge. |
| 3 | M&L for cement concrete type B1 1:2:4 (20mm graded aggregate) in coping, kneelers, apex stones, bed plates, kerbs complete all as specified |
| 4 | Demolition of concrete (reinforced) of any description and in any position not otherwise specifically provided for and removing the debris and rubbish outside MoD land at any distance complete all as specified. |
| 5 | M&L for RCC 1:1½:3 A1 (20mm graded stone aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies and in shelves and all as specified |
| 6 | S&F MS TMT Bars of 8 mm dia and over,cut to length,bent to shape required including cranking, binding spirally for hooping for columns hooking ends and biniding with and including MS wire (annealed) not less than 0.9 mm dia or securining with clip all as specified. |
| 7 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) |
| 8 | Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide. |
| 9 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), including disposal of debris out side the MoD land etc complete all as specified and directed. |
| 10 | M&L Machine cut mirror polished kota stone slab flooring 18-20mm thick over and including cement screed base in CM(1:4) 15mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed |
| 11 | M&L Machine cut mirror polished Kota stone slab 18-20mm thick in riser of steps, skirting, dado and pillar laid over and including cement screed in CM 1 :4, 15 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete |
| 12 | M&L for Non -skid Ceramic coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick cement mortar screedbed in CM 1:6 etc complete all as specified and directed by Engr-in-Charge |
| 13 | M&L for Non-skid Ceramic tiles 8 to 9 mm thick (600mmx600mm) (square/ rectangular), light shade, polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick cement mortar screedbed in CM 1:6 etc complete all as specified and directed by Engr-in-Charge |
| 14 | M&L for Glazed coloured ceramic tiles in vertical surface 450X 300X 6-7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match including rendering 10mm thick on fair faces of brick work in CM 1:4 as backing coat complete all as specified and directed by Engr-in-Charge |
| 15 | Dismantling of Stone slabs and tiles laid, bedded and pointed in any mortar of any description or thickness in floors, aprons etc laid beded and pointed in any mortar including removing debris outside MoD area at any distance complete all as specified. |
| 16 | M&L for Machine cut cudappah stone slab 18-20mm thick over and including 15m thick screed bed or bedding layer in cement mortar (1:4), laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete |
| 17 | M&L 18-20mm thick mirror polished Granite (of any type) work (table rubbed and polished) as in steps, jambs, pillars, window- cills, cooking platforms, working table and like over 15m thick screed bed or bedding layer in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite. |
| 18 | M&L for udaipur green/baroda green marble slab 18-20 mm thick on vertical surface, steps, jambs, pillars, window cills, cooking platforms and like, machine cut, bedded and jointed with grey cement slurry over and including 15mm thick rendering in CM 1:3 and pointed with white cement using marble dust with admixture of pigment to match the shade of marble slab including grinding and polishing complete all as specified and directed. |
| 19 | Providing edge moulding to 18 -20mm thick Granite work, marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. |
| 20 | S&F in repair PVC 10 litre capacity valve less syphonic action type, flushing cistern, low level, white/coloured with inlet ball valve, float and handle including brackets, etc. complete all as specified by Engineer in Charge. |
| 21 | S&F in repair Vitreous china wash down water closet pan ( pedestal pattern ) white including, connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc. with flush pipe PVC 32mm dia and Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device; complete all as specified & directed. |
| 22 | S&F in repairs Vitreous china squatting pan Orissa pattern, size 580x440mm white with integral foot rests including necessary lime concrete and connecting to flushing pipe, antisyphonage pipe etc. for connecting WC to branch piece with cement joints, fixed in repairs complete all as specified. |
| 23 | S&F in repair Wash basins, Vitreous China (flat back or angle back type) size 550x400mm, including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed by Engr-in-Charge |
| 24 | S&F in repair plastic water closet seat and cover (coloured) and mild steel chromium plated or aluminized hinges devices complete all as specified and directed by Engr-in-Charge. |
| 25 | S&F in repair Health faucet (ABS Body) with jet spray, 1.5m long, cast copper alloy, nickel chromium plated finish, 15mm bore 100mm long with wall hook chromium plated fitted to stop cock complete all as specified and directed. |
| 26 | S&F in repairs CP towel rail 600mm long with round flange complete all as specified and directed. |
| 27 | S&F in repair 15mm Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed |
| 28 | S&F 600mm long PVC connections 15mm size with PTMT nuts complete all as specified and directed. |
| 29 | S&F in repair 15mm fancy type chromium plated Angle valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed |
| 30 | Taking down eaves gutters and rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed. |
| 31 | Supply and fixing PVC (SWR) 110mm bore pipes in any length with rubber ring joints fixed to wall complete all as specified and directed. |
| 32 | S & F for Pipe Supporting Clamping - Single Pipe of dia 110 mm (4\\") down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt Rubber Sleeve mounted System running vertically with wall distance 75 mm (3\\") Material Qty. for one unit : 1. Profile Bracket Wall distance 75 mm (3\\") - 2 Nos. 2. Continuous Slotted C Channel of Size 250 mm (10\\") - 1 No.; 3. U Bolt Rubber sleeve mounted for 110 mm (4\\") CI or PVC Pipe Dia. - 1 No.; and 4. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2\\") - 4 nos. All other detail as specified in Chief Engineer Navy Mumbai Technical Drawing (TD) of Pipe Supporting System No. TD/2023/01 to TD/2023/03 complete all as specified and as directed (upto 9 Storey). |
| 33 | S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed. |
| 34 | S&F for Pipe Supporting Clamping - Single Pipe of dia 75mm (3\\") down take pipe fixing done with Clamping System consists of Profile Bracket + Continuous Slotted C Channel + U Bolt Rubber Sleeve mounted System running vertically with wall distance 75 mm (3\\") Material Qty. for one unit : 1. Profile Bracket Wall distance 75 mm (3\\") - 2 Nos. 2. Continuous Slotted C Channel of Size 250 mm (10\\") - 1 No.; 3. U Bolt Rubber sleeve mounted for 75mm (3\\") PVC Pipe Dia. - 1 No.; and 4. Fixing Nail Zn coated of thickness 6.5 mm and length 63 mm (2 1/2\\") - 4 nos. All other detail as specified in Chief Engineer Navy Mumbai Technical Drawing (TD) of Pipe Supporting System No. TD/2023/01 to TD/2023/03 complete all as specified and directed by Engr-In- Charge. |
| 35 | S&F PVC (SWR) reducers 110mm bore complete all as specified and directed by Engr-In- Charge. |
| 36 | S&F PVC (SWR) bend any radius with oval access door 110mm bore complete all as specified and directed by Engr-In- Charge. |
| 37 | S&F PVC (SWR) bend any radius with oval access door 75mm bore complete all as specified and directed by Engr-In- Charge. |
| 38 | S&F PVC (SWR) branch pieces, single (single Y) equal or unequal 75 mm bore without oval access door complete all as specified and directed by Engr-In- Charge. |
| 39 | S&F PVC (SWR) branch pieces, single (double Y) equal or unequal 110 mm bore without oval access door complete all as specified and directed by Engr-In- Charge. |
| 40 | S&F PVC (SWR) vent cowl 75mm bore with cement joints complete all as specified and directed by Engr-In- Charge. |
| 41 | S & F PVC (SWR) branch piece, Single (single T) equal or unequal for 75 mm bore with oval access door complete all as specified and directed by Engr-In- Charge. |
| 42 | S&F PVC (SWR) floor trap, plain with grating including jointing with solvent cement for 75 mm outlet pipe complete all as specified and directed by Engr-In- Charge. |
| 43 | Supply and fixing 40mm dia high density polyethylene pipes (HDPE) of pressure rating 6 kgf/sqcm of fixed to wall, floors for drain out the waste water from Kitchen Sink, WHB etc includding socket, tee, bend etc & screw complete all as specified and directed by Engr-in-Charge. |
| 44 | Supply and fixing in repair stainless steel plate rack 0.63mm thick stainless steel sheet overall size stainless steel plate rack 36” x 24” x 10” kitchen rack all as specified and as direted. |
| 45 | Taking down chowkats or frame (w/o taking off shutters from the frames) not exc. 1.50 sqm each complete all as specified and directed. |
| 46 | Taking down chowkhats or frame (w/o taking off shutters from the frames) but exc 1.50 but n.exc 4.00 Sqm each complete all as specified and directed. |
| 47 | Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 45 x 85 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction ofEngineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 48 | Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and nontoxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 49 | S&F 100mm stainless steel butt hinges, ISI marked, medium weight and fixed complete all as specified. |
| 50 | S&F 125mm size extruded aluminium alloy handles, ISI marked, fabricated type anodised fixed with SS screws complete all as specified and directed. |
| 51 | S&F 125mm long aluminium anodised barrel tower bolts of extruded section, ISI marked, fixed with SS screws complete all as specified and as directed. |
| 52 | Supply and fixing Aluminium anodised section 15 micron for window (Sliding type) / ventilator (Partly fixed partly louverd type) etc of anodised aluminium section ventilators partly fixed partly louvered type comprising frame, shutters, locking arrangements including necessary jamming, glazing pins, neoprene beading, glazing pin screw, levered aluminium sections for louvered glass, rollers , handle etc including taking down existing window complete all as specified and directed. Note: (a) Glazing shall be measured separately. (b) Item shall be paid as per weight of aluminium section. (c) Rate quoted shall be inclusive of neoprene beading, glazing clips, screw etc as required which not be measured for arriving the weight. (d) Rate shall be inclusive of the aluminium handle, locking arrangement including complete packing with silicon gel around contecting surface of aluminium and including matching the existing surface area complete all as specified and directed. (e) Aluminium window / ventilator etc to be fixed with cadmium plated screw not more than 300mm c/c. |
| 53 | M&L for aluminium anodised grill with suitable aluminium anodised frame section manufactured by M/S Deco grill pattern DG-102 (7.5mm dia and aparture 50mm) complete all as specified and directed by Engr-in-Charge. |
| 54 | S&F 5.5 mm thick plain glass ordinary quality in square n.exc 0.50 sqm each fixed to aluminium window frame complete all as specified and directed. |
| 55 | S&F 5.5 mm thick frosted glass ordinary quality in square n.exc 0.50 sqm each fixed to aluminium window frame complete all as specified and directed. |
| 56 | Taking down cement plaster any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc. and disposal of rubbish outside MoD land at any distance. Note :- Rates should include steel pipe scaffolding upto G+5 story bldg |
| 57 | M&L for rendering 20mm thick plaster (in two layer of 15mm + 5mm th) with ready mix prepacked proportioned dry mix mortar on brick wall or concrete surfaces, including transporting of material, mixing, curing, etc.complete all as specified and directed by Engr-In- Charge. Note:- (i) The plaster should be carried out in two layer first layer should be 15mm finished with brush mark and the second layer of 5mm thick plaster.(ii) After finishing the first layer it should be curing for next 14 days before applying the second layer of plaster and applying second layer of plaster same curing process will be follow as intial one.(iii) Rates should include steel pipe scaffolding upto G+5 story bldg |
| 58 | M&L for rendering 15mm thick plaster with ready mix prepacked proportioned dry mix mortar on brick wall or concrete surfaces, including transporting of material, mixing, curing, etc.complete all as specified and directed by Engr-In- Charge. |
| 59 | M&L for preparation of newly plastered surfaces of wall and applying two coats of oil emulsion distemper over a coat of alkali resistance primer complete all as specified and directed by Engr-In- Charge. |
| 60 | M&L for applying two or more coats of Acrylic Smooth exterior paint of required shade on newly plastered wall surfaces @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm complete all as specified. |
| 61 | Demolition of Brickwork or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles & removing debris out of MoD land at any distance complete all as specified. |
| 62 | M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in CM 1:6. |
| 63 | Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed |
| 64 | S&F Rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc and similar work conforming Fe 290 (Gde E- 165) including working platform/scaffolding complete all as specified & directed by Engr-in-Charge |
| 65 | Fabrication and erection fixing only rolled sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc and similar work conforming Fe 290 (Gde E- 165) including working platform/scaffolding complete all as specified & directed by Engr-in-Charge |
| 66 | M&L preparation of new or previously untreated steel surface any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified. |
| 67 | M&L for preparation of old painted steel and iron surfaces of any description over 10cm width or girth not otherwise described and applying one coat of synthetic enamel paint all as specified and directed by Engr-in-charge |
| 68 | Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings |
| 69 | M&L for pre-painted hot-dip aluminium-zinc alloy metallic coated corrugated steel sheet, any pattern correspondings to IS 15965:2012 of durability class 3, atmospheric classification category 3, coating class AZ150, 0.50mm thick, of an approved colour and having yield strength of 550 MPa as in roof covering fixed with self tapping screws as specified including necessary scaffolding and safety measures at any floor for height of building exceeding 10 metres but not exceeding 20 metres complete all as specified and directed. |
| 70 | Cutting chases, pinning in and making good to facings of brick/concrete/stone walling where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed. |
| 71 | M&L for filleting in any position and to any shape of section area not exc 25 sq cm in cement sand mortar 1:4 including all mitres, stops etc complete all as specified and as directed. |
| 72 | Supply and fixing 10 mm dia 100 mm long dash through fasteners bolts fixed in concrete or brick work to hold brackets etc complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysOct 30, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 8 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender