Tender For Addition/ Alteration To Building No. T-25 & P-36 At Cdu Goa And Provision Of Additional Cabling Connection Of Existing Dg Set To Dsc Pump House At installation Gomantak Under Ge Gomantak Vasco
Tender Value
48.20 Lakhs
Estimated cost
Bid Submission
29 Oct 2026
7 days left
EMD
96400
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
goa → Goa
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Addition/ Alteration To Building No. T-25 & P-36 At Cdu Goa And Provision Of Additional Cabling Connection Of Existing Dg Set To Dsc Pump House At installation Gomantak Under Ge Gomantak Vasco
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 16-Oct-2026 | Corrigendum1 | BOQ | 29-Oct-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling of plain or corrugated steel sheeting, any gauge, thickess including Nainital or similar pattern roofs covering complete all as specified and directed. |
| 2 | Dismantling wrought iron or mild steel work of any description complete all as specified and directed. |
| 3 | Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/slabs/blankets, any thickness including cover fillets complete all as specified and directed. |
| 4 | Demolition of cement concrete unreinforced in ground floors and pavings n.exc. 15 Cm thickness (below or above ground level) complete all as specified and directed. |
| 5 | Demolition of Brick Work/ stone work / concrete block wall built in Cement Mortar including all quoins, arches, pillars etc. of any descriptions complete all as specified and as directed. |
| 6 | Dismantling floor, hearth or wall tiling including cement mortar bedding (including backing), removing tiles and rubbish off the premises complete all as specified and directed. |
| 7 | Taking down cement or cement lime plaster on walls/ concrete/ roof slab any description including racking out joints hacking for key, scrubbing down with water etc. complete all as specified and directed. |
| 8 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and directed. |
| 9 | Taking down Chowkats or frames with shutter (without taking off shutters from the frame) n. exc. 1.50 sqm each complete all as specified and directed. |
| 10 | Taking down Chowkats or frames with shutter (without taking off shutters from the frame) exc. 1.50 sqm and n. exc. 4.00 sqm each complete all as specified and directed. |
| 11 | Taking down shutters of any description exc 1 sqm & n. exc 2 sqm each complete all as specified and directed |
| 12 | Taking down shutters of any description exc 2 sqm each complete all as specified and directed |
| 13 | Excavation in trenches in soft/disintegrated rock, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and getting out complete all as specified and as directed. |
| 14 | Taking up or down existing GI tubing and connections, including making good the disturbed surface for 15 mm dia pipes complete all as specified and directed. |
| 15 | Taking up or down existing GI tubing and connections, including making good the disturbed surface for 20 mm dia pipes complete all as specified and directed. |
| 16 | M&L for plain cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling & mass concrete complete all as specified and directed. |
| 17 | M&L for cement concrete 1:4:8 type D-2 (using 40 mm graded stone aggregate) 100 mm thick as in sub base finishing the surface even and rough to receive floor complete all as specified and directed. |
| 18 | M&L for 75 mm thick cement concrete type C-1 1:3:6 (using 20 mm stone graded crushed stone aggregate) as in plinth protection surface finished even and smooth without using extra cement including forming construction (dummy) joints 6 mm wide & 10 mm deep and filled with filler at an interval not exceeding 3 metre and at change of direction and necessary formwork complete all as specified and directed. |
| 19 | Removing building materials by truck or tractor with using of if necessary JCB machine and trolly load min 5.00 Cum each load including loading, unloading and stacking at the destination and depositing out side defence land complete all as specified and directed. |
| 20 | M&L for precast cement concrete block masonry, type C-1 (1:3:6) (20 mm graded aggregate) with solid blocks, exc 10 cm in width and setting in CM 1:6 complete all as specified and as directed. |
| 21 | M&L for rendering on fair faces of brick work or concrete surface or block masonary, 15 mm in CM 1:4, mixed with liquid water proofing compound as per manufacturer instructions finished the surface even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid seperately |
| 22 | M&L for rendering 10 mm thick on other than fair faces of brick work or concrete surface in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed. |
| 23 | M&L for rendering 5 mm thick on ceiling in cement mortar 1:3 including finishing the surface even and smooth without using extra cement complete all as specified and directed. |
| 24 | M&L for 25 mm thick cement concrete 1:2:4 type B-0 (using 12.5 mm graded stone aggregate) as in flooring/ levelling course finished rough to receive floor/screed complete all as specified and directed. |
| 25 | M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square or rectangular) area of each tiles exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed. |
| 26 | M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square or rectangular) area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm as in floor set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles lad over & including screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed. |
| 27 | M&L for joint free non skid ceramic coloured tiles 7 to 8 mm thick (square or rectangular) of size and design as per floor tiles fixed on vertical surfaces such as dado, skirting etc. jointed and pointed in white or coloured cement to match the existing surface with & including rendering 10 mm thick in cement mortar 1:4 finished rough to fix tiles complete all as specified and directed. |
| 28 | M&L for machine cut kota stone slab of size not less than 550 x 550 mm (except where lesser size required) as in flooring or in trades of steps (in single piece) 20 to 25 mm thick and jointed with grey cement slurry mixed with pigment to match the shade of the slab including grinding, rubbing, rounding of edges and mirror finish polishing with & including screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed |
| 29 | M&L for machine cut kota stone 18-20 mm thick as in steps, risers, skirting, dado etc., bedded and jointed with grey cement slurry and pointed in white cement with admixture of pigment to match the shade of the stone including grinding, rubbing and mirror polishing laid over and including rendering 10 mm thick in cement mortar 1:3 finished rough to fix stone complete all as specified and directed. |
| 30 | M&L for joint free glazed ceramic coloured tiles or ceramic designer tiles of size 450 x 350 x 7 mm thick in vertical surface set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface with & including rendering 10 mm thick in cement mortar 1:3 finished rough to fix tiles complete all as specified and directed. |
| 31 | M&L for chequered cement concrete tiles 200 x 200 x 25 mm thick set jointed and pointed in neat coment slurry in floors with grey cement and pigment with & including screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed. |
| 32 | M&L for PCC 1:2:4 type B-1 (using 20 mm graded crushed stone aggregate) as in lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, copings, over chajja, walls and the like including weathering, slightly rounded or chamfered angles and throating as directed with and including necessary form work and necessary scaffolding/ staging/ Jhula etc. with necessary safety precautions upto 4 story height complete all as specified and directed. |
| 33 | Supply only liquid water proofing compound |
| 34 | Providing & fixing false ceiling at all heights With Semi perforated 10 mm thick micro tegular edged GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595 x 595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC 0.50 to 0.75 as per IS 8225:1987, Noncombustible as per BS 476 (part 4) -1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on interlocking metal T-Grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @ 120 grams per Sqm including both sides) comprising of main-T runners of size 15 x 32 mm of length 3000 mm, cross-T of size 15 x 32 mm of length 1200 mm and secondary intermediate cross-T of size 15 x 32 mm of length 600 mm to form grid module of s1ze 600 x 600 mm, suspended from ceiling using galvanized mild steel items (galvanizing @ 80 grams per sqm) i.e 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1m length and L shape level adjuster of size 85 x25 x 2 mm. Galvanised iron perimeter wall angle of size 24 x 24 x 0.40 mm of length 3000 mm to be fixed on periphery wall I partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws complete all as per specifications, drawing and as directed. |
| 35 | M&L Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings. |
| 36 | S&F in position anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised alumnium snap beading, screws etc. complete all as specified |
| 37 | S&F Anodised aluminium grill (anodised transparent or dyed to required shade according to IS 1868 with minimum anodic coating of grade AC 15) of approved design/ pattern with approved standard section and fixed to the existing window frame with CP brass/ stainless steel screw @ 200 mm centre to centre including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening all complete all as specified and directed. |
| 38 | S&F solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube and fixed with screws and rawl plugs complete all as specified and directed. |
| 39 | S&F Factory made solid PVC moulded door shutter 28 to 30 mm thick(stiles) with 2, 4 or 6 raised panel design with 2 mm thick moulded PVC Sheet on the front face & 2 mm plain colour PVC sheet on back face, with particle board core, supplying & fixing in frame at site complete all as directed. |
| 40 | M&L for 4.8 mm thick sheet glass frosted and fixed with oil putty or rubber beading, wooden/aluminium beads and provsion of glazing pins where required in squares exceeding 0.50 Sqm in each pane fixed in wooden/ aluminium/ steel windows/ doors/ partition/ ventilators complete all as specified and directed.Note :- Aluminium glazing strip/ metal strip paid sepetately under respective item. |
| 41 | S&F solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturer's complete all as specified and directed. |
| 42 | S&F aluminium (extruded section) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed complete all as specified and directed. |
| 43 | S&F floor door stopper of of brass body and tongue with hard drawn steel spring, fixed in floor having overall length of cover plate 150 mm complete all as specified and directed. |
| 44 | S&F brass mortice lock 4 levers, vertical type, of size 65 mm including plate and two keys including making hole in pressed steel frame complete all as specified and directed. |
| 45 | S&F 150 mm long Brass handles, fabricated type, polished bright complete all as specified and directed. |
| 46 | S&F aluminium anodised barrel tower bolt of extruded section 200 mm long and fixed complete all as specified and directed. |
| 47 | S&F 100 mm size mild steel butt hinges, ISI marked, medium weight, cold rolled and fixed with screws/welded to frame complete all as specified and directed. |
| 48 | S&F extruded aluminium alloy handles, fabricated type, anodised 150 mm size complete all as specified and directed. |
| 49 | S&F aluminium anodised barrel tower bolt of extruded section 125 mm long and fixed complete all as specified and directed. |
| 50 | S&F 75 mm size butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type C-21 and fixed complete all as specified and directed. |
| 51 | S&F extruded aluminium alloy handles, fabricated type, anodised 125 mm size complete all as specified and directed. |
| 52 | S&F 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed all as specified and directed. |
| 53 | Excavating in post holes(or similar holes) each n.exc 0.5 cum in hard/dense soil, getting out, returning, filling in, watering and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm and removing surplus soil to a distance n.exc 50m and making good surfaces complete all as specified and directed. |
| 54 | S&F rolled mild steel in roof trusses(framed), trussed purlins, crane gantries, rails and fastenings, MS pipe for post and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to Fe- 290(Gde E-165) complete all as specified and directed. |
| 55 | S&F rolled mild steel in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 56 | S&F mild steel work as in bands, straps, supports or stays for rainwater, Ventilating pipes, including bolts, if required; hooks ( stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three ways straps, plate washers and similar small articles conforming to Fe- 290.Gde-E-165 complete all as specified and directed. |
| 57 | S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 58 | S&F Pre- painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering, ridge, hip and vally gutters, fixed with self tapping screws as specified complete all as specified and directed. |
| 59 | Supply, fixing, laying & testing CPVC pipes 16 mm outer dia SDR 11 including Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed. |
| 60 | Supply, fixing, laying & testing CPVC pipes 20 mm outer dia SDR 11 including Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed. |
| 61 | S&F Tank adaptor for 20 mm dia CPVC pipe complete all as specified and directed. |
| 62 | S&F Ball valve for 20 mm dia CPVC pipe complete all as specified and directed. |
| 63 | S&F 20 mm dia gun metal globe or gate valve with iron wheel head screwed both ends and for iron pipe & fixed complete all as specified and directed. . |
| 64 | Disconnecting existing water tank of capacity exc. 250 ltr but not exc. 500 ltr, setting aside (or lowering of required) for cleaning, repairs to roofs etc. and hoisting if required reconnecting and refixing in position on roof including Cleaning and removing all scale and dirt, etc, with bleaching power, brush from mouths of circulating pipes etc capacity exc 250 and not exc 500 Ltr each including write date of cleaning and next due date complete all as specified and directed. |
| 65 | Dismantling water tank capacity exc. 500 ltr but n.exc. 1000 ltr complete all as specified and directed. |
| 66 | S&F in position white colour three layered rotational moulded polyethylene water storage tanks 1000 lts capacity (cylinderical vertical with closed top) hoisted and fixed in position incl GI/CPVC tank nipple all as specified in SSR Part I complete all as directed |
| 67 | S&F in repair 20mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 68 | S&F 10 ltr PVC valveless, syphonic action type, flushing cistern, low level, white, with intel, ball valve, float and handle including brackets complete all as specified and directed |
| 69 | S&F Viterous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) and including Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 70 | S&F vitreous china wash hand basin, white, flat back 550 x 400 mm excluding tap but including brackets 2 numbers including cutting for and pinning in ends of brackets, 32 mm CP brass waste coupling with long screwed shanks and fly-nuts, flange end bedded in red lead cement complete all as specified and directed. |
| 71 | S&F vitreous china urinal half stall type, white excluding flushing cistern, flush pipe and waste pipe but including grating and union for discharge pipe complete including providing and fixing plugs, bedding urinal agianst wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement complete all as specified and directed. |
| 72 | S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 73 | S&F PVC connection 450 mm long suitable for 15 mm GI pipe with two PTMT nuts & rubber washers complete all as specified and directed. |
| 74 | S & F stop valve/angle valve 15 mm nominal bore cast copper alloy, fancy type, chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipes or for unions and fixed complete all as specified and directed. |
| 75 | S&F stop valves 15 mm nominal bore, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type), screwed down, high pressure with crutch or butterfllly handles, screwed both ends for iron pipe or for brass ferrule or to GI socket complete all as specified and directed . |
| 76 | S&F long body bib taps, cast copper alloy, fancy type, chromium plated with crutch or butterfly handles, screwed down, screwed for 15 mm bore GI pipe or for brass ferrule or to GI socket complete all as specified and directed. |
| 77 | S&F pillar taps, cast copper alloy, with capston heads, fancy type, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15 mm bore iron pipe and fixed complete all as specified and directed. |
| 78 | S&F 600mm x 450 mm x 5.5 mm thick bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and aluminium angle alround fixed to wooden plugs with chromium plated brass screws & washers complete all as specified and directed. |
| 79 | S&F 20 mm dia brass chromium plated tubular towel rail, D type, 60 cm long between flanges fixed with rawl plug complete all as specified and directed. |
| 80 | S&F 75 mm dia PVC (SWR) floor trap, with stainless steel grating including jointing to waste pipe with solvent cement and fixed in cement concrete 1:2:4 type B1(using 20 mm graded stone aggregate) complete all as specified and directed. |
| 81 | S&F chromium plated brass shower roses 125 mm dia with or without swival joints, including fixing to 15 mm dia pipe or union all as specified. |
| 82 | S&F PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive and laid in trenches or in floors complete all as specified and directed. |
| 83 | S&F PVC (SWR) pipe 110 mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive and fixed to walls complete all as specified and directed. |
| 84 | S&F PVC (SWR) pipe 75 mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive and laid in trenches or in floors complete all as specified and directed. |
| 85 | S&F PVC (SWR) pipe 75 mm bore, single socketed, in any length with rubber ring joints and jointed with approved adhesive and fixed to walls complete all as specified and directed. |
| 86 | S&F PVC (SWR) bend 110 mm dia, any radius fixed to pipe complete all as required and as directed. |
| 87 | S&F PVC (SWR) bend 75 mm dia, any radius fixed to pipe complete all as required and as directed. |
| 88 | S&F PVC(SWR) branch pieces 110 mm bore single (single Y) equal or unequal complete all as specified and directed. |
| 89 | S&F PVC(SWR) branch pieces 75 mm bore single (single Y) equal or unequal complete all as specified and directed. |
| 90 | S&F PVC (SWR) vent cowl 110 mm bore complete all as specified and directed. |
| 91 | S&F PVC (SWR) vent cowl 75 mm bore complete all as specified and directed. |
| 92 | S&F PVC(SWR) junction single (single T) equal or unequal for 110 mm bore complete all as specified and directed. |
| 93 | S&F 125/110 mm PVC (SWR) gully trap including jointing to waste pipe with solvent cement and fixed in cement concrete 1:2:4 type B1(using 20 mm graded stone aggregate) complete all as specified and directed. |
| 94 | M&L for PCC 1:3:6 type C-2 ( using 40 mm graded stone aggregate) as in bed to drain pipes including packing under and completely surrounding the pipes with concrete after they are laid and tested for 100/110 mm bore pipe complete all as specified and directed. |
| 95 | M&L for preparation of new or previously untreated steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer all as specified and directed. |
| 96 | M&L for preparation of new or previously untreated steel surfaces exceeding 10 cm width or girth and applying two coats of synthetic enamel paint all as specified and directed. |
| 97 | M&L for preparation of old surface of wall and applying one coat of oil bound distemper complete all as specified and directed. |
| 98 | M&L for preparation of old surface of ceiling and applying one coat of oil bound distemper complete all as specified and directed. |
| 99 | M&L complete removal of existing treatment of wall and applying one coat of alkali resistant primer on plastered surfaces of wall over 1.5 mm thick wall care putty and applying two coat of oil bound distemper including preparation of old surfaces complete all as specified and directed. |
| 100 | M&L complete removal of existing treatment of ceiling and applying one coat of alkali resistant primer on plastered surfaces of wall over 1.5 mm thick wall care putty and applying two coat of oil bound distemper including preparation of old surfaces complete all as specified and directed. |
| 101 | M&L for applying one coat of alkali resistant primer on plastered surfaces of ceiling over 1.5 mm thick wall care putty and applying two coat of oil bound distemper including preparation of new surfaces complete all as specified and directed. |
| 102 | M&L for applying one coat of alkali resistant primer on plastered surfaces of wall over 1.5 mm thick wall care putty and applying two coat of oil bound distemper including preparation of new surface of wall complete all as specified and directed. |
| 103 | Material and labour for applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489-2004 alkali and fungal resistance, dirt resistance exterior emulsion paint of required shade (Company Depot tinted) with silicon addtitives @ 1.43 litre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 ltr/10 Sqm etc on newly plastered surface of wall including preparation of surface complete all as specified. |
| 104 | M&L for RCC 1:2:4 type B-1(using 20 mm graded stone aggregate) as in slab, beams, cantilevers, bressummers, lintels over 1.5 m span complete all as specified and directed. |
| 105 | Use and waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete complete all as specified and directed. |
| 106 | M&L for reinforced precast cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in landings, cover slabs (for manholes etc.), chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces including necessary form work, set in cement mortar 1:4 complete all as specified and directed. (Reinforcement shall be measured and paid for separately under respective item of schedule 'A'). |
| 107 | M&L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90 mm dia or securing with clips complete all as specified and directed. |
| 108 | M&L for mild steel TMT bars 5 mm dia and over in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia or securing with clips complete all as specified and directed. |
| 109 | M&L for granite stone 18 to 20 mm thick (of any type) glazed (table rubbed and polished) fixed as in steps, jambs, pillars, window cills, cooking plateform and the like set in cement mortar 1:4 and pointed with white cement (1:2) using marble dust with admixture of pigment to match and exposed edges rounded laid over and including screed bed or bedding layer of mortar 20 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and directed. |
| 110 | S&F rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe- 290 (Gde E-165) complete all as specified and directed. |
| 111 | S&F steel rolling shutters, with lath thickness of 1.25 mm without ball bearing as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, erected in position as indicated, complete gear operated type with bevel gear box and crank handle complete all as specified and directed |
| 112 | Supply & Fixing safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and directed. |
| 113 | Supply & Fixing only Ball bearing for rolling shutters complete all as specified and directed. |
| 114 | M&L for Cement concrete concrete 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in surface channels and drains including necessary forom work complete all as specified and directed. |
| 115 | Extra for forming fair finished drains or channels 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. complete all as specified and directed. |
| 116 | Returning filling in including spreading levelling, watering and well ramming in layers n.exc 25 cm thick in any type of soil/rock complete all as specified and directed. |
| 117 | Removing excavated material (Soils/rock) to a distance not exceeding 50 m and depositing where directed at a level n.exc. 1.5 m above the starting point complete all as specified and directed. |
| 118 | M&L for hardcore of broken stone or boulder gauge n.exc. 63 mm deposited, spread & levelled in layers n.exc. 15 cm thick watered and rammed to a true surface complete all as specified and directed. |
| 119 | Taking down copper/ aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc. to match the existing complete all as specified and directed.NOTE: Credit for this items shall be made as per conditions separately. |
| 120 | M&L for point wiring complete for one light/ fan/ exhaust fan point controlled by one, one way 5/6 Amp switch with PVC (FRLS) insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including minimum 20 mm dia 'medium grade' PVC conduit ISI marked concealed in wall and fittings and modular metal flush box, modular white cover plate with frame, blanking plate and cutting chases in wall/ ceiling incl making good to the disturbed surfaces to match the existing including 1.50 sqmm nominal cross sectional area PVC(FRLS) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories complete all as specified and directed.Note- (i) Rates include the cost of blanking plate, modular plate, modular boxes and covers of suitable modules as required at site.(ii) Modular box, plate and cover shall be of same make as of switch//socket/regulator. |
| 121 | All as per item No. 120 above but for one 5 pin 5/6 Amp socket outlet point on same board |
| 122 | All as per item No. 120 above but for one 5 pin 5/6 Amp socket outlet point on an independent board. |
| 123 | All as per Item No 120 above but for one 6 pin 15/16 amps socket outlet point on an independent board with FRLS cables of size 4 Sqmm and green colour earth cable of size 4 Sqmm. |
| 124 | S&F modular type switch one way 6 Amps, 230 Volt, 1 Module complete all as specified and directed. |
| 125 | S&F modular type switch one way 16 Amps, 230 Volt, 1 Module complete all as specified and directed. |
| 126 | S&F modular type socket one way 6 Amps, 2/3 pin, 230 Volt, 2 Module complete all as specified and directed. |
| 127 | S&F modular type socket one way 6/16 Amps, 2/3 pin, 230 Volt, 2 Module complete all as specified and directed. |
| 128 | S&F ceiling rose, two or three terminal, surface bakelite 65 x 50 mm complete all as specified and directed. |
| 129 | S&F in replacement MCB single pole 240 volts, 'C' curve of rating from 16 to 32 amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed. |
| 130 | S&F in replacement MCB SPN 240 volts, 'C' curve of rating 40-63 Amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed. |
| 131 | S&F in replacement MCB tripple pole(TP) 415 volts, 'C' curve of rating 63 Amps, with rupturing capacity 10 KA, including providing thimble for out going cables complete all as specified and directed. |
| 132 | S&F in replacement sheet metal enclosure MCB distribution board, double door with IP-43 protection single pole and neutral 240 volts, 8 way, including suitable size copper bus bar and metal door, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces complete all as specified and directed. |
| 133 | S&F in replacement brushless direct current (BLDC) ceiling fan 1400 mm sweep with service value 6.00 BEE, 5 star rating complete with blades and other accessories, single phase, 230 V including suitable size GI pipe down rod and making connection with sheathed 3 core cable of size 0.75 Sqmm flexible copper conductor wire complete all as specified and directed. NOTE:- Old fan will be deposited to MES store yard.Make : Havells cat No- FHCNF5SWHT56/Orient model Hector 500/ Bajaj Model- ENERGOS 28(SKU Code 251100EE) |
| 134 | S&F in replacement exhaust fan (Metal body) of 300 mm sweep, AC single phase 230/240 volts, 1400 RPM, heavy duty complete including making electric connection with PVC insulated three core 1.5 Sqmm copper cable from ceiling rose to exhaust fan complete all as specified and directed.NOTE:- Old exhaust fan will be deposited to MES store yard.Make : Orient Ind heavy duty 1400RPM/ Havells Turbo force 1P(FHEHDSPDB120) /Bajaj Supreme plus Ind fan |
| 135 | S&F modular type fan regulator, electronic step type, 120 W, 2 Module complete all as specified and directed. |
| 136 | Supply & install in replacement storage type water heater (Geyser) capacity 25 Ltrs five star rating GMV type prefixing and grouting work for mounting nuts, bolts and washer etc. in wall and reconnecting all inlet/ outlet/ vent pipes, electrical/ earthing connections and carrying out testing for proper functioning complete all as specified and directed.NOTE:- Old geyser will be deposited to MES storeyard.Make:- Havells MONZA DX 25L/ Bajaj CALENTA (M)/ Racold OMNIS DG 25 L |
| 137 | S&F in replacement sheet metal enclosure MCCB distribution board, double door with IP-43 protection TPN, 415 Volts, 8 way, Vertical type, including suitable size copper bus bar and metal door, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces complete all as specified and directed. |
| 138 | S&F in replacement MCCB 100 Amps, 415 volts, 50 Hz, 4 pole, 16 KA breaking capacity with thermal magnetic setting including providing suitable size aluminium lugs, speders complete all as specified and directed. |
| 139 | S&F in replacement LED street light fitting 70/72 Watts, having pressure die cast aluminium alloy housing with high power LED as lightning source and lens embedded PC cover having top opening seperately including Driver having IP-66 protection and S&F GI tubing 40 mm dia light grade bracket 1.20 m long bent to shape by cutting and welding, fixed with 2 Nos. FI clamps 50x6 mm nuts, bolts and washers and making connection using 1.5 Sqmm PVC insulated cable with copper conductor single core complete all as specified and directed. Make- Crompton CRP-409-70-57-SL-GL-NSG/ Havells Cat no: ENDURASUNDOWNNXT SL70WLEDCWPASYBOPC/ Bajaj ZELA P 86L WH PO TG SD J |
| 140 | S&F in repair sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 10 Sqmm nominal cross sectional area and one run of 10 sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including not less than 32 mm PVC conduit and fittings fixed on wall/ roof/ floors/ ceiling etc. including cutting chases to walls for laying conduit wherever required and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed.NOTE:- One unit length shall measured as two run of main wire, one run of earth wire and one run of PVC conduit |
| 141 | S&F in repair sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 4 Sqmm nominal cross sectional area and one run of 4 sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including not less than 25 mm PVC conduit and fittings concealed in wall/ roof/ floors/ ceiling etc. including cutting chases to walls for laying conduit wherever required and making good the disturbed wall surfaces to match with existing specification complete all as specified and directed.NOTE:- One unit length shall measured as two run of main wire, one run of earth wire and one run of PVC conduit |
| 142 | M&L removing existing earthing and new earthing complete with galvanised steel plate electrode 600mm x 600mm x 6mm thick buried directly in ground (earth pit not less than 2.25 Mts deep below ground level with top edge of the plate not less than 1.50 Mtrs below ground level connected to glavanised iron Wire 4.0 mm dia by means of bolts, nuts check nuts and washers of galvanised iron or steel connected to earthing test point all as specified incl 15 mm GI tubing medium grade and necessary fitting for protection of GI wire incl laying of charcoal dust and common salt in alternate layer, PCC Pit (1:3:6) type C-1 using 20 mm graded stone aggregate, RCC cover 40mm thick (1:2:4) type B-0 using 12.5 mm graded stone aggregate reinforced with 6 mm dia round bar @ 75 mm C/C both ways with MS handle 8 mm dia, plastering 15 mm thick CM (1:6) externally upto 150mm below ground level, GI funnel with 20mm dia medium grade GI pipe for watering and wire mesh incl. excavation and earth work and disposal of surplus soil complete all as specified and shown on electrical plate No. 3 of SSR Part (2009) and connected to earth test point incl testing complete all as specified an directed.Note:- The unit rate includes the cost of GI pipe medium grade for protection of earth wire and 4mm dia earh lead wire upto 7.5 M. |
| 143 | S&F in replacement existing U/S light fitting with LED tube light fitting surface and wall mounted batten Aluminium body with 10 watts LED having minimum 100 lumens/watts and with integrated electronic driver complete all as specified and directed. Make: Havells LUMILINEPLUSNEOBS10WLED865SPCSSINDS/ Crompton CCS-103-10-65-SL-DP-NWH/Bajaj DAWN AL 10W CW PD |
| 144 | S&F in replacement existing U/S light fitting with LED tube light fitting surface and wall mounted batten Aluminium body with 22/20 watts LED having minimum 100 lumens/watts and with integrated electronic driver complete all as specified and directed. Make: Havells LUMILINEPLUSNEOBS20WLED865SPCSSINDS/ Crompton CCS-100-20-65-HL2-DP-NWH/Bajaj DAWN AL 20W CW PD |
| 145 | S&F in replacement LED luminaire 600 mm x 600 mm, 35/36 watt, 6500 K, 220 V AC recessed type fully diffused, CCT, luminous efficiency of not less that 120 lm/watt designed for metric false ceiling type or alongwith frame suitable for Armstrong/ US Gypsum or similar mounting system with concealed or exposed ‘T’ section, Glare free light alongwith electronic driver complete with all accessories prewired and connecting with three core twisted flexible copper conductor cable complete all as specified and directed.Make:- Orient cat part No-LTRAQ-36-C-VO-AL/ Phillps cat part No-RC380BLED36S-6500 G5 L60W60PSUODSG /Bajaj Cat part BZRSQL 43 L LED GX PRO WH |
| 146 | Excavation in trenches in hard/dense soil, n exc 1.5 m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sqm on plan and getting out complete all as specified and as directed. |
| 147 | S&L in replacement XLPE LT UG cable PVC insulated, bedded armoured heavy duty electric cable 1100 volts grade with aluminum conductor of 70 Sqmm 3.5 core including gland, lugs etc. laid in trenches or fixed on wall/floor/poles complete all as specified and directed. |
| 148 | Supply & laying double walled corrugated (DWC) HDPE full rounded pipe conforming to IS 16205 Pt-24 of approved colour complete with fittings for cable protection of size 38 mm inner dia and 50 mm outer dia complete all as directed. |
| 149 | Supply and installing, testing, commissioning split AC unit indoor/ outdoor, with cordless remote control unit and inbuilt air iodiser and plasma filter for better indoor air quality, minimum 5 star rating and ISEER rating of 3.75, 2 TR capacity with copper tubing condenser non-inverter compressor, low noise with 230 Volt range, LED display, anti-dust, antimicrobial protection, anti-corrosive coating, self diagnosis with all necessary fixing arrangements such as brackets etc. complete all as specified and directed.Make : Voltas Modal 243VH Vertis Elegant/ Blue star Model FA324YLU/ LG US-Q24ENXENote:- Extra copper tubing, water pipe, voltage Stabilizer etc. required to complete the installation will be measured and paid separately under respective items herein after. |
| 150 | S&F Voltage stabilizer 5 KVA capacity, single phase, naturally Air Cooled indoor type and designed for input variation between 130 V to 280 V with output voltage stabilized at 230 V with accuracy of + 2.5 % complete all as specified and directed. Make: V-Guard/MicroTek/Luminous |
| 151 | S&F flexible wire three core, PVC insulated 4 Sqmm multi stranded copper conductor, 1100 V grade complete all as specified and directed. |
| 152 | S&F insulation for copper tubes of split type AC units, insulation type superlon of size 3/8\\" diameter all as directed. |
| 153 | S&F insulation for copper tubes of split type AC units, insulation type superlon of size 5/8\\" diameter all as directed. |
| 154 | S&F copper tubing soft grade suitable for split type AC suction /discharge line of size 5/8\\" diameter all as directed. |
| 155 | S&F copper tubing soft grade suitable for split type AC suction /discharge line of size 3/8\\" diameter all as directed. |
| 156 | Supply and fix 20 mm dia PVC flexible drain pipe heavy duty with necessary fittings for Split AC's complete all as directed. |
| 157 | S&F sheet metal enclosures, single pole and neutral with a two pin and earth plug and socket, plug top and one single pole MCB 20 Amps, C series 240 V complete all as specified and directed. |
| 158 | S&L XLPE LT UG cable PVC insulated, bedded armoured heavy duty electric cable 1100 volts grade with aluminum conductor of 50 Sqmm 3.5 core including gland, lugs etc. laid in trenches or fixed on wall/floor/poles complete all as specified and directed. |
| 159 | S&L XLPE LT UG cable PVC insulated, bedded armoured heavy duty electric cable 1100 volts grade with aluminum conductor of 185 Sqmm 3.5 core including gland, lugs etc. laid in trenches or fixed on wall/floor/poles complete all as specified and directed. |
| 160 | Supply & laying double walled corrugated (DWC) HDPE full rounded pipe conforming to IS 16205 Pt-24 of approved colour complete with fittings for cable protection of size 50 mm inner dia and 63 mm outer dia complete all as directed. |
| 161 | Supply & laying double walled corrugated (DWC) HDPE full rounded pipe conforming to IS 16205 Pt-24 of approved colour complete with fittings for cable protection of size 94 mm inner dia and 110 mm outer dia complete all as directed. |
| 162 | Cutting the existing road/ PCC/ RCC/ Hard standing for passing pipe/ cable and making good the disturbed surfaces by using cement concrete 1:3:6 type C-1 (using 20mm graded crushed stone aggregate) as in mass concrete complete all as specified exists complete all as specified. |
| 163 | S&F off load changeover switch 250 A, 4 pole complete fixed to sheet metal enclouser/ MCB DB with all necessary fixing arrangements complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 16, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Oct 29, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 7 daysOct 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender