Tender For Addition/Alteration & Special Repair To Certain Bldgs At The Inf School, Mhow
Tender Value
2.83 Crore
Estimated cost
Bid Submission
05 Nov 2026
21 days left
EMD
3.58 Lakhs
Bank guarantee accepted
Document Fee
2000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Indore → Madhya Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition/Alteration & Special Repair To Certain Bldgs At The Inf School, Mhow
BOQ
| Sl. No. | Item Description |
| 1 | SCHEDULE A |
| 2 | Item No1 : Demolition of cement concrete (un reinforced) in ground floor and paving n. exc. 15cm thickness (below or above ground level. |
| 3 | Item No2 M & L 25mm thick cement concrete type B-0, 1:2:4 (using 12.5 mm graded aggregate) for levelling course in floors complete all as specified and directed. |
| 4 | Item No3 : M & L for 75mm thick cement concrete 1:3:6 type C1, with using 20mm graded stone aggregate as in floor/ plinth protection finish the surface even and smooth with using extra cement including filling the expansion joints with bitumen filler / filler boards and necessary form work etc complete all as specified and as directed. |
| 5 | Item No4 :M & L forTreating the soil along with external perimeter of building at the rate of 2.25 litre of emulsion per metre of the perimeter wall complete all as directed and specified. |
| 6 | Item No5 :M&L for Treatment of soil under existing floors using emulsion @ one ltr per hole 300mm apart including drilling and plugging 12mm dia holes to match the existing floors with cement mortar 1:2 (1 cement : 2 coarse sand) to match the existing floors all as directed and specified. |
| 7 | Item No6 :Taking down chowkhats or frames not exc 1.5 sqm each without taking off shutter from the frame complete. |
| 8 | Item No 7 :Taking down chowkhats or frame exc 1.5 sqm but not exc 4 sqm with shutter (without taking off shutter frome the frame ) |
| 9 | Item No 8 :S & F 125 x 60 mm size Pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate,hold fast includ etc., complete as specified |
| 10 | Item No 9 :S & F 105 x 60 mm size Pressed steel frames for door with one or more rebates including necessary lugs, hinges, lock strike plate,hold fast include etc., complete as specified |
| 11 | Item No 10 :M&L for PCC (1:2:4) type B-0 with using 12.50 mm graded stone aggregate as in bed blocks, coping, for fixing holdfast/lugs,filling hollow space of pressed steel door frame etc including necessary form work all complete as specified and as directed. |
| 12 | Item No 11 :M & L 2nd class Hard wood 35 mm thick Plain , framed panelled shutters ( any number of panels), with panels of timber flat on both sides (feather edged) or of veneered particle board medium density, wood particle board with commercial face veneers fitted to chowkats complete all as speciifed and directed. |
| 13 | Item No 12 : S & F 2nd class Hard wood 35 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass , gauze, etc, (without sash bar) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) fitted to chowkats complete all as specified and directed. Note :- Glass pane and wire mesh shall be measured and paid separately in respective supply only item. |
| 14 | Item No 13 : Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads |
| 15 | Item No 14 : M & L for 3mm thick sheet glass ordinary quality and glazing with oil putty/fixing in wooden frame with beading in square not exc. 0.5 sq m in each pane. |
| 16 | Item No 15 :S & F for Stainless steel wire cloth of 0.36mm dia wire and average width of aperture 1.4mm & fixed with tacks of stainless steel wire staples,etc complete all as specified and as directed. |
| 17 | Item No 16 :S & F in repair for Stainless steel wire cloth of 0.36mm dia wire and average width of aperture 1.4mm & fixed with tacks of stainless steel wire staples,etc complete all as specified and as directed. |
| 18 | Item No 17 :M&L for preparation of new wooden surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint over a coat of filler coat with grey filler or liquid wood filler, transparent, and bringing forward surfaces to smooth even finish, comlete, all as specified. |
| 19 | Item No 18 :M&L for Preparation of Old painted surface of Wood of any description and applying one coat of synthetic enamel paint over 10cm width or girth complete all as specified and as directed. |
| 20 | Item No 19:S&F for factory made solid PVC door frame of size 50mm x 47mm made out of plain 5mm plain colour PVC sheet reinforced with ms square tube, with wooden grain printed PVC sheet used inserted of plain colour PVC sheet & edges will be painted to match with printed sheet complete all as specified and as directed. |
| 21 | Item No 20 : S&F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of ms tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and as directed. |
| 22 | Item No 21 : S&F for factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of ms tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, complete all as specified and as directed. |
| 23 | Item No 22 S&F for 100 mm Butt hinges, heavy weight, cold rolled stainless steel, and fixed |
| 24 | Item No 23 S&F for 75 mm Butt hinges, heavy weight, cold rolled mildsteel, and fixed |
| 25 | Item No 24 : S & F aluminium 200 mm long anodised barrel tower bolts ISI marked of extruded section and fixed complete. |
| 26 | Item No 25 : S & F aluminium 150 mm long anodised barrel tower bolts ISI marked of extruded section and fixed complete. |
| 27 | Item No 26 S & F 150 mm size aluminium handles cast type, anodised ISI marked complete |
| 28 | Item No 27 : S & F 300 mm mild steel, ordinary rat tail rod pattern spring including roller and roller plate complete fixed to steel frame / wooden frame including necessary welding, cutting, opening of wall for fixing bracket and making good complete. |
| 29 | Item No 28 : S&F 300mm length, aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy. |
| 30 | Item No 29 : M&L for floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, 140mm long, fixed in floor complete all as specified |
| 31 | Item No 30 : S & F in repair curtain rails 20 mm dia, decorative type, stainless steel including fixing brackets in both sides fancy type complete all as specified and directed.. |
| 32 | Item No 31: S& F in repair ss curtain finials/ bracket /clamps fixed to curtain rod complete all as specified and directed |
| 33 | Item No 32 :S & F in repair powder coated aluminium door seal 30mm wide and length as per requirement of site including dust/insect arrestor complete all as specified and directed. |
| 34 | Item No 33 : S & F Powder coated aluminium sliding glazed windows with three track shutter sliding (two shutters glazed and one shutter wire mesh) shall be of two parts and upper patr shall be three movable shutter and lower part consist three shutter (one openable in centre and both side fixed type shutter with frosted glass) with following specification and making good the adjacent side of jombs of windows by plastering in CM 1: 3 even and smooth complete etc . shifting of existing cooler stand where required complete all as specified and as directed by Engr-in-charge.(ii) Three way track for sliding shutters of cross section 91.8mm x 31.75mm x1.1mm thick.(Min)(iii) Sliding shutter frame of cross section 40 x 18 x 1mm thick.(Min)(iv) 4 mm thick glass superior quality.(Min)(v) IDPE Rubber guasket for fixing of glass.(vi) Locking cleats per shutter -01 Nos.(Min)(vii) Sliding rollers per shutter - 02 Nos.(Min)(viii) Stainless steel wire cloth 0.30mm nominal dia of wire and average width of aperture 1.40mm for shutters 01 Nos.(Ix) fixing screw for frame with wall per windows- 08 Nos. |
| 35 | Item No 34 : S & F powder coated aluminium ventilator of frame having cross section conforming to IS 63.5x38.10x1.5mm consisting of two partions upper portion shall have louvers with 3mm thick pin headed glass and aluminium wire cloth 0.30mm nominal dia of wire and average width of aperture 1.56m fixed with aluminium beads and securing on outer face of frame and lower portion of ventilation shall be fixed with 3mm thick pin headed glass with IDPE rubber gasket including aluminium beads, including preparation of jombs all around in CM 1:3 finishing even and smooth complete all as specified and directed. |
| 36 | Item No 35 : M&L mild steel framed work such as grills , gratings, etc., with ends of bars shouldered and/ or riveted, or forged in to spikes; framed guard bars ; barred iron doors; ladders; framed balusters ; walk ways ; railings; frame work of water tanks and similar work conforming to Fe-290 Gde E-165 complete all as specified. |
| 37 | Item No 36 : Demolition of Brick work built in cement mortar including all quoins arches pillars etc complete all as specified and directed |
| 38 | Item No 37 M&L for brick work with sub class 'B' bricks straight or curved on plan exc. 6.00m mean radius built in cement mortor 1:6., etc complete all as specified and directed. |
| 39 | Item No 38 M & L for reparing of RCC projection, chajjas, RCC facia etc by necessary preparation i.e scrapping ,cutting,chiseling,derusting and cleaning exposed reinforecement, surfaces of damaged, loose RCC surfaces and applying one coat of rust remover by brushing to rusted reinforecemnt to remove loose rust particles and allow to dry it for 2 to 3 Hrs , insert the new reinforcement to damaged portion by drillig hole at required distance , fill the epoxy in to the hole by 2/3 of the hole and insert the reinforcement in the hole, and binding the reinforcement at rusted portion of reinforcement, apply cement slurry on entire damaged area , and plaster the surfaces with cement , sand and Polymer liquid in 1: 3 : 15% of cement by weight ) and water as required , mixing properly and plaster the surface , finished even and smooth by making the edge water dropping groves complete all as specified and directed. Note : (i) Cost of formwork shall be deemed to be included.(ii) Cost of reinforcement shall be measured and paid seperatly |
| 40 | Item No 39 Taking down cement plaster, any description on brick or stone or cement concrete walls including raking out joints, hacking for key, scrubbing down with water etc. |
| 41 | Item No 40 M&L for rendering 15mm thick cement plaster in CM 1:6 on fair faces of brick work or concrete surfaces and surface finished even and smooth without using extra cement complete all as specified and directed. |
| 42 | Item No 41 M&L for rendering 15mm thick cement plaster in CM 1:4 on fair faces of brick or concrete surface with liquid water proofing compound @ 200 ml per bag finished even and fair without using extra cement complete all as specified and directed.(Note:- Liquid water proofing compound to be measured paid separately) |
| 43 | Item No 42 Supply only Liquid Water proofing compound PIDIPROOF LW+ of Dr FIXIT or equivalent as approved. |
| 44 | Item No 43 M&L for rendering 5mm thick in ceiling CM 1:3 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed. |
| 45 | Item No 44 M&L for Complete removal of old treatment By mechanical meanson internal/External surfaces of wall & celling by scrapping and washing etc all as specified.Note : Scraping/Removing is to be carried out upto 15.00m height .The contractor is advised to visit the site before quoting the tender.The rate quoted by contractor will deemned to be inclusive of necessary sacffolding work etc required at site. |
| 46 | Item No 45 M&L for plaster surface of wall and and applying 2mm thick cement base waterproof wall care putty in two coat (each coat not less than 1mm) over on walls and surface finished even and smooth with sand paper complete all as specified and directed. |
| 47 | Item No 46 M&L for preparing plastered surface of walls and applying two coat of oil bound distemper white or any tint over a coat of primer etc complete as specified and directed |
| 48 | Item No 47 M&L for preparation of plaster/Putty surface of walls and applying a priming coat of exterior weather proof primer applied Min @ 2.20 kg/10 sqm or as per OEM on External walls by spray and finished the surface even and smooth complete all as specified and directed.Note:(1) Painting is to be carried out upto 15.00m height .The contractor is advised to visit the site before quoting the tender.The rate quoted by contractor will deemned to be inclusive of necessary sacffolding work etc as required.(2) Primig coat should be done as per manufacturer reqmt of weather proof paint. |
| 49 | Item No 48 M&L for two coats of Exterior weather proof acrylic Emulsion paint (Two or more coat applied @ 1.67 ltr/10 sqm) using roller/spray and make the surface smooth all as specified and prescribed by manufacturer of paint and all as directed at site by Engr-in-Charge Note:- putty shall be measured separately & Periodical is to be carried out upto 15.00m height .The contractor is advised to visit the site before quoting the tender.The rate quoted by contractor will deemned to be inclusive of necessary sacffolding work etc required at site |
| 50 | Item No 49M&L two coats of white wash on old plastered / concrete celling sufaces incuding preparation of surfaces. |
| 51 | Item No 50 M&L three coats of white wash on newly plastered / concrete celling sufaces incuding preparation of surfaces. |
| 52 | Item No 51 Dismantling of stone slabs and tiles of any description or thickness in floors, aprons etc laid, bedded and pointed in any mortar complete all as specified and directed |
| 53 | Item No 52 Dismantling of floor hearth or wall tilling including cement mortar bedding (but not backing) and rubbish of the premisses complete all as specified and directed. |
| 54 | Item No 53 M&L for scratch free Vitrified Tiles 9mm to 10mm thick (square or rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.36 sqm (ie) of size 600x600mm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match with colour of tile over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 complete all as specified |
| 55 | Item No 54 M&L for glazed ceramic coloured tiles of size not less than 450x300x7 mm thick as on vertical surfaces such as wall, dado ,skirting etc set and jointed in neat cement slurry and pointed with coloured cement to match over 10 mm thick backing coat on fair faces of brick work in CM (1:4) complete all as specified and as directed. |
| 56 | Item No 55 M&L for non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular) of size 400x400mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tile including 15 mm thick screed bed or bedding layer in cement mortar 1: 6 complete all as specified |
| 57 | Item No 56 All as per item No 53 above but as in skirting/ dado etc with and including 10mm thik backing coat in cement mortar 1:4 on wall complete all as specified |
| 58 | Item No 57 M&L for non skid ceramic coloured tiles 7mm to 8mm thick (square/rectangular) of size 300x300mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tile including 15mm thick screed bed or bedding layer in cement mortar 1: 6 complete all as specified |
| 59 | Item No 58 M&L for machine cut kota stone slab in flooring 18-20 mm thick laid over and including 20mm thick screed bed in cement mortar 1:6 and pointed with cement mixed with pigment to match with the shade of slab including rubbing and polishing complete all as specified |
| 60 | Item No 59 All as per item-56 above but as in skirting/ dado etc with and including 10mm thik backing coat in cement mortar 1:4 on wall complete all as specified |
| 61 | Item No 60 M&L for PCC1:4:8 type D-2 using 40mm graded stone aggregate as in sub base of floor, etc complete all as specified and directed |
| 62 | Item No 61 M&L for hardcore of broken stone or boulder of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface |
| 63 | Item No 62 M&L for sand cushioning for Machine pressed precast concrete interlocking paver block including watering and consolidation. |
| 64 | Item No 63 M&L for coloured Machine pressed precast concrete interlocking paver block any shape and size confirming to IS-15658-2006 of 60mm thickness, M-35 grade including taking out of old damaged interlocking paver block. |
| 65 | Item No 64 M&L for chequered cement concrete tiles with grey cement and pigment of size 40cmX40cmX25mm thick ,set and jointed and pointed in neat cement slurry in floor etc over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed. |
| 66 | Item No 65 S&F in repairs incl hoisting HDPE plastic water cylindrical vertical type tanks closed top of capacity 500Ltrs incl 20mm bore brass stop cock and 20mm bore brass float valve with polythene float complete all as specified. |
| 67 | Item No 66 S&F in repairs incl hoisting HDPE plastic water cylindrical vertical type tanks closed top of capacity 1000Ltrs incl 20mm bore brass stop cock and 20mm bore brass float valve with polythene float complete all as specified. |
| 68 | Item No 67 S&F 25mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors inc all fittings complete all as specified. |
| 69 | Item No 68 S&F 20mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors inc all fittings complete all as specified. |
| 70 | Item No 69 S&F 25mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors inc all fittings For Hot water complete all as specified. |
| 71 | Item No 70 S&F 16mm bore CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors inc all fittings complete all as specified. |
| 72 | Item No 71 S & F in repairs Sink with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes coupling , including bedding in cement mortar to dwarf wall or including fixing cantiliver brackets and connecting union to pipe overall size 915 mm x 460mm bowl size 410 mm x 330 x 160 mm complete all as specified and directed. |
| 73 | Item No 72 S & F in repairs vitreous china wash hand basin white, flat back of size 550mmx400mm fixed on and including cast iron cantilever bracket, 32mm dia brass waste coupling and 32 mm dia PVC waste pipe including fixing of tap, waste fitting etc complete.. Note :- Pillar tape shall be measured as supply only under respective item |
| 74 | Item No 73 S&F vitreous china wash down water closet pedestal pattern white excluding flushing cistern and flush pipes complete all as specified and as directed . |
| 75 | Item No 74 S&F PVC valve less,syphonic action type flushing cistern,low level ,white with inlet ball valve,float and handle including flush pipe, brackets and connection to pipe and fixing of chain and pull or lever if any complete all as specified and directed. |
| 76 | Item No 75 Supply only PVC connection pipe 15 mm dia 450 long with PTMT nut at both ends for hot and cold water complete. |
| 77 | Item No 76 S&F in repair 600mmx450mm mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers complete all as specified and directed at site. |
| 78 | Item No 77 S & F in repair brass chromium plated angle cock 15 mm dia screwed for iron pipe or brass ferrule, complete all as specified . |
| 79 | Item No 78 S & F in repair brass chromium plated towel rail 20 mm outer dia Bracket type, 60 cm long between flanges with and including chromium plated brass screws and wooden / plastic cleats, complete. |
| 80 | Item No 79S & F in repair over head shower with arm & flnge of chromium plated with or without swivel joints, any size, including fixing to 15mm dia steel pipe for required length or union complete all as specified and directed |
| 81 | Item No 80 S&F in repair 15 mm dia consealed type stop valves, cast copper alloy, chromium plated, screwed down, high pressure with handle, screwed both ends for iron pipe or union complete all as specified and directed |
| 82 | Item No 81 S&F in repair 15mm dia Bib tap chromioum plated with crutch or butterfly handle sorewed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed. |
| 83 | Item No 82 S&F in repairs powder coated steel peg set having 06 Nos spikes fixed to wall complete all as specified and directed (Make as spproved by GE) |
| 84 | Item No 83 S & F PVC bath cabinet box with mirror type minimum size 600x450 mm with shutter complete all as specified and directed |
| 85 | Item No 84 S & F in repair corner shelf of 300 mm size with ABS brackets complete. complete all as directed and specified. |
| 86 | Item No 85 S & F CP Thumbler Holder, complete all as specified and directed by Engineer-incharge. |
| 87 | Item No 86 S&F in repair fancy type chromium plated15mm bore two way Bib cock cast copper alloy with crutch or butterfly handle, screwed for iron pipe or brass ferrule etc complete all as specified and as directed. |
| 88 | Item No 87 S&F Health faucet mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified |
| 89 | Item No 88 S& F CP toilet paper holder complete all as specified and as directed. |
| 90 | Item No 89 S&F in repair CP wall mixer, for mixing hot and cold water fancy type cast copper alloy , with capstan heads, chromium plated , screwed down for 15 mm bore pipe,high pressure with long screwed shanks and fly-nuts , screwed for iron pipe ISI Marked of other specified. |
| 91 | Item No 90 Supply only 15 mm dia bore basin mixture brass chromium plated with capstan heads screwed down high pressure with or without letter ‘HOT’ or ‘COLD’ with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified and directed. |
| 92 | Item No 91 S & F in repair PVC (SWR) floor trap plain or multi with stainless steel grating incl joining to waste pipe with solvent cement joint dia of outlet 75mm bore complete all as specified and as directed. |
| 93 | Item No 92 S&F in repair for 20mm dia Gun-metal, golbe or gate valves, with iron wheel head, screwd both ends or iron pipe and fixed |
| 94 | Item No 93 S&F stainless steel plate rack for kitchen 1mm thick of best quality with suitable hanging arrangement and fixed to wall complete all as spd and directed by Engr-in-Charge.Note : siz of plate rack should not be less than 900x 600mm and weight of rack shall not be less than 7.00 kg each. |
| 95 | Item No 94 S&F in repairs soap dish (ovel) type mild steel chromium plated of size not less than 50mm dia complete. |
| 96 | Item No 95 S&F in repair CP bottle trap 32mm bore for wash basin with inlet and outlet screwed for connection including necessary packing union and cup and fixed. |
| 97 | Item No 96 S & F in repairs 110 mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to walls or floor or in trench complete all as specified and directed. |
| 98 | Item No 97 S & F in repair 110 mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed. |
| 99 | Item No 98 S & F in repair 110 mm bore PVC (SWR) vent cowl complete all as specified and directed. |
| 100 | Item No 99 S & F in repair 75mm bore PVC (SWR) vent cowl complete all as specified and directed. |
| 101 | Item No 100 S & F in repair 110 mm bore PVC (SWR) bend any radius complete all as specified and directed. |
| 102 | Item No 101 S & F in repairs 75 mm bore PVC (SWR) pipes singles socket in any length with rubber ring joints fixed to walls or floor or in trench complete all as specified and directed. |
| 103 | Item No 102 S & F in repair 75 mm bore PVC (SWR) bend any radius complete all as specified and directed. |
| 104 | Item No 103 S & F in repair 75 mm bore PVC (SWR), junction single, (Single T) equal or unequal complete all as specified and directed. |
| 105 | Item No 104 Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and as directed |
| 106 | Item No 105 S & F for Anodised aluminium snap grid size (605mmx605mm) frame work for false ceiling with Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified. |
| 107 | Item No 106 M&L for GI snap grid framework including 4mm thick Desginer E-boards for false ceiling (grid size 605mm x 605mm ) including necessary notching and preparing holes powder coated white/ivory colour. complete all as specified and directed |
| 108 | Item No 107 M & L for Exposed metal frame ceiling with minimum 6mm calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600 mm x 600mm grid (Frame work for ceiling shall be measured and paid separately) complete all as specified. |
| 109 | Item No 108 Dismantling of Asbestos cement (corruga ted, semicorrugated, etc.) sheets in roof coverings etc complete all as specified and as directed. |
| 110 | Item No 109 S&F 0.50mm thick (including coated thickness) pre-colour pre- profiled (Galvalume/zinkalume) sheets of required colour and design having tensile strength of 550 Mpa as in roof sheeting/sunshade/ wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and min 150mm end lap laid to slope all as per manufacturer / profile maker instruction complete all as specified and as directed. |
| 111 | Item No 110 Dismantling of timber scantlings as in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section in un-framed work complete all as specified and directed. |
| 112 | Item No 111 M&L in for MS steel Hollow Section work in tubular trussles, purlins, rafter, tubler column, where connected common rafter and running rails fixed with angle cleat or other connection plates including special shaped washer etc, complete using ERW or induction butt welded tubes conforming IS-4963,1993 and IS-1161-1979 grade ST-240 complete all as specified and as directed. |
| 113 | Item No 112 M&L in for Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) conforming IS-1161-1979 grade ST-240 complete all as specified and as directed. |
| 114 | Item No 113 S&F Mild steel plates (Plain or chequered) as in shoe plate, base plate and gusset plates forming holes for roof frame work, trusses, rafters etc of grade Fe 410 WA. complete all as specified and as directed |
| 115 | Item No 114 Preparation of newly steel surfaces, of any description, over 10 cm width or girth, and applying two coats of synthetic enamel paint over a coat of red oxide complete complete all as specified and as directed |
| 116 | Item No 115 S&F for 18 mm thick factory made PVC sheet one side pre-laminated sheet ktichen cabinet shutter. The 18mm thick sheet shutter bent at 90 degree and finish all edges at level for marking edge lipping bending for 0.5 mm thick PVC sheet lipping at all four edges using bonding tape etc complete all as per specified and directed. |
| 117 | Item No 116 S & F for factory made PVC shelf/partition of required size consisting of panel of 18 mm thick required size consisting of panel of 18 mm thick celuka PVC ply and for supporting the hold of shelf /partition and shall provided 3 edges in size 18mm x 18 mm as per required lenght the front side of the edge visible in the front of the shelf/partition to be edge lipped by 18mm widht x 1 mm thick PVC sheet of density 600 kg/cum manufactured by ISO 9001-2015 Certified Company , using solvent cement etc. complete all as specified. |
| 118 | Item No 117 S & F modular type stainless steel basket size 0.50 m x 0.53 m x 0.10 m (dia of wire not less than 3.0mm) of any shape with and including side sliding roller clip and sliding rails on both side fixed with steel screws incl all fixing arrangement complete as specified and dirceted. |
| 119 | Item No 118 All as per item no 112 as above but basket size 0.50 m x 0.53 m x 0.15 m complete as specified and dirceted. |
| 120 | Item No 119 All as per item no 112 as above but basket size 0.50 m x 0.53 m x 0.21 m complete as specified and dirceted. |
| 121 | Item No 120 S&F 100mm size MS mat/glossy finish handle complete as specified and directed. |
| 122 | Item No 121 S&F stainless steel self closing hinge/Auto hinge of 75mm size for PVC door shutter complete as specified and directed. |
| 123 | Item No 122 S&F 50x15mm size magnet door catcher for closing for PVC door shutter complete as specified and directed. |
| 124 | Item No 123 S&F SS steel drawer cabinet channel for moving the drawer etc complete as specified and directed. |
| 125 | Item No 124 S&F 40mm flaps width (when open) continuous (Piano) hinges mild steel bright finish or electrogalvanised |
| 126 | Item No 125 S& F 18/19 mm thick Block boards, grade 2 quality, interior grade, commercial type, conforming to IS fixed with screws timber frame work as in cupboard , wardrobe etc. |
| 127 | Item No 126 M & L 0.9 mm thick Decorative laminate type 1, of surface finish, colour and pattern as approved, conforming to IS fixed with approved adhesive over 18/19 mm thick plywood as per manufacturer's instructions complete all as directed and specified. |
| 128 | Item No 127 Demolition and breaking up drain pipe of dia 150 mm (internal dia) (salt glazed stoneware, AC or reinforced conrete) set in cement mortar complete all as specified and directed. |
| 129 | Item No 128 M&L for DWCPE pipe of 180mm outer dia/ mini 150mm inner dia meter pipes for sewage disposal including testing complete all as specified and directed |
| 130 | Item No 129 M & L cement concrete bed to drain pipe including packing under and haunching against side of pipe after they are laid and tested in cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate for the 150 mm internal dia of pipe complete all as specified and directed |
| 131 | Item No 130 Excavation in trenches n. exc 1.5m wide and n. exc 1.5m in depth in any type of soil for foundation, etc or for shafts, wells, cesspits, manholes, pierholes, etc and getting out complete all as specified and directed |
| 132 | Item No 131 'M&L for returning filling in any type of soil including spreading levelling watering and well ramming in layers n. exc 25cm thick complete all as specified and directed |
| 133 | Item No 132 M&L for removing excavated material (Soils) to a distance n. exc 50m and depositing where directed at a level n. exc 1.5m above the starting point complete all as specified and directed |
| 134 | Item No 133 Grinding and mirror polishing of old kota stone flooring /marble flooring including wax complete all as specified and directed. |
| 135 | Item No 134 S&F powder coated aluminium frame work as in door shutter ,windows , ventilators, partitions with one or more rebates sections of approved tint as required for partitions including beading,cleat, screws,fasteners, plugs, for fixing with wall/ceiling columns/beams etc complete all as specified |
| 136 | Item No 135 S & F second class hard wood plain, solid straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified. |
| 137 | Item No 136 Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed |
| 138 | Item No 137 M&L for RCC 1:2:4 type B1 (using 20mm graded stone agg) as in slab and shelves supported on walls complete all as specified and directed |
| 139 | Item No 138 'M&L form work to soffits of suspended slab such as roof slab/lintel band and similar work n. exc 200mm thick (horizental or sloping) rough finished flat surface complete all as specified and directed |
| 140 | Item No 139 M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed |
| 141 | Item No 140 S&F 1 mm thick laminate Sunmica sheet over external surface old wooden surface with adhesive complete all as specified and as directed |
| 142 | Item No 141 M&L for 18- 20 mm thick Granite slab work (table rubbed and polish) of approved quality of required size in floor,wall,cooking platform and like bedded and jointed in grey cement slurry and pointed with coloured cement (1:2) usig marble dust with admixture of pigment to match the shade of granite stone laid over and including 20 mm thick screed bed in cement mortar 1:6 including polishing by using mechanical grinder inc molding of front side as per requirement complete all as specified and directed. |
| 143 | Item No 142 S&F for 20mm dia Gun-metal, golbe or gate valves, with iron wheel head, screwd both ends or iron pipe and fixed |
| 144 | Item No 143 Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 95 sq mm 3½ core. |
| 145 | Item No 144 Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 50 sq mm 3½ core. |
| 146 | Item No 145 Excavating in trenches, in any type of soil not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc and getting out in any type of soil complete all as specified and directed. |
| 147 | Item No 146 Returning, filling in excavated approved soil, including spreading, leveling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.. |
| 148 | Item No 147 Removing excavated soil not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed. |
| 149 | Item No 148 Supply laying and jointing GI pipe 'light grade' 50 mm bore in trenches/under floors or roads/ along poles/ on wall incl clamps for protection of cables incl fittings complete all as specified and directed. |
| 150 | Item No 149 M & L for clean and dry sand (un-washed) in trenches incl spreading and levelling for cushioning of UG cable complete all specified and directed. |
| 151 | Item No 150 Supply and laying unreinforced precast concrete cable cover, class LV, type 1 with flat, size 250 mm x 150 mm x 40 mm, complete all as specified and as directed. |
| 152 | Item No 151 Supply, installation, testing and commissioning out door type LT panel board ,made out of 3.15mm thick CRCA sheet , factory made, CPRI Approved, cubical type,with slanting top at leaset 10 Cm projection all around, fedder pillar type,fabricated with 50x50x6mm angle iron frame work with independent door for each feeder,busbar chamber cable tray on both side fully compartmentlized design, double door type & commen openable hinged door from rear side, floor mounting type, busbars made of aluminium duly insulated with heat retardent fire proof (HRFR) heat shrinkable sleeves of relevant colours.Bus bar shell be properly supported/mounted on epoxy insulators.All live parts and joints shall be insulated with (HRFR) shrouds, conforming to IS, including provn for connecting suitable earth strips,painting with one coat of anti corrosive coating and finally epoxy polyester powder coating of flint Grey shade (RAL-7032), Confirming to IP 54 protection and confirming relavent IS, comprising the adequate arrangement to supply & fix the following accessories,including connecting cable glands and cable lugs,fixing of earth lead to earth terminal of panel including necessary excavation & PCC foundation complete all as specified & Directed by Engr-in-Charge.( Note:- Cost of all accessories are deemed to be included in the rate quoted). Incoming (a) Copper bus bar - 600 Amps rating - 04 Nos. for phases and neutralb) MCCB 4 pole 400 Amps, 415 volt, 36 KA - 01 No ( incoming)(c) 3 phase Voltmeter (0-500V) digital type with selector switch-01 No(d) 3 phase Ammeter (0-400 Amps) digital type with CT's of suitable ratio and selector switch - 01 No.(e) ON/OFF LED type indication lamp with toggle switch - Set of 03Out going:-(a) MCCB , 4 Pole, 25 KA, 160 amps - 04 Nos b) MCB , 4 Pole, 25 KA, 40 amps - 03 Nos |
| 153 | Item No 152 Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc. |
| 154 | Item No 153 Taking down old/unserviceable distribution board by disconnection of electric connection carefully SPN DBs/TPN DBs/ Main Switch including old unserviceable MCCBs/ MCBs, Isolators, etc and making good to disturbed surface all as specified and directed at site. |
| 155 | Item No 154 Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as specified and directed. |
| 156 | Item No 155 Taking down ceiling fan/ exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of AGE E/M complete all as specified and as directed. |
| 157 | Item No 156 M&L for point wiring with 1.5 Sq mm single core PVC insulated unsheathed copper FRLSH multi stranded conductor cable in and including Concealed PVC conduit of size 20/25mm ISI marked inclusive of tees ,bend ,elbows etc upto and including modular sunken anodised steel box for housing modular switch socket , regulator etc including modular cover plate and cover frame of any module ISI marked of suitable size complete including PVC insulated multi stranded copper conductor 1.5 Sq mm FRLSH cable as earth wire to common earth dolly for connection to ceiling rose to earth terminal including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed by Engr-in-charge for One light point controlled by one, one way switch 5 Amps (a) One light point/bell/fan point controlled by one switch |
| 158 | Item No 156.01 (b) One light point/fan controlled by Two switch |
| 159 | Item No 156.02 (c) One 5amps socket out let point controlled by one switch on same board with other switches. |
| 160 | Item No 156.03 (d) One 5amps socket out let point on independent board controlled by one switch. |
| 161 | Item No 157 Description all as per item No 7 here in before but using 2.5 sq mm single core copper conductor cable of multistranded FRLSH PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket cobmination point on independent board including necessary running of 2.5 sq mm copper conductor FRLSH PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly. |
| 162 | Item No 158 S & F for Modular Switch , single pole, one way, and 5/6 Amp single module complete all as specified. |
| 163 | Item No 159 S & F for Modular Switch , single pole, two way, and 5/6 Amp single module complete all as specified. |
| 164 | Item No 160 S & F for Modular Switch , single pole, one way, and 15/16 Amp single module complete all as specified. |
| 165 | Item No 161 S & F for Modular Socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module complete all as specified. |
| 166 | Item No 162 S & F for Modular Socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module complete all as specified. |
| 167 | Item No 163 S & F for for Bell push modular 6 Amps single module complete all as specified. |
| 168 | Item No 164 S & F for lamp holder , PVC / Polycarbonate type with back plate suitabl for batten/ slanting fittings complete all as specified and directed. |
| 169 | Item No 165 S & F for Ceiling rose, surface Bakelite with 3 terminals, ISI marked for batten fitting complete all as specified |
| 170 | Item No 166 S & F for Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed |
| 171 | Item No 167 S & F for modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed. |
| 172 | Item No 168 Supply and fix brushless direct current motor (BLDC) ceiling fans complete with blades(03Nos), with remote control and accessories , 230 V, 50 Hz, 1200 mm sweep, Min air delivery 210 CMM with service value greater than 7.75 BEE. Five star rated, provide electrical connection from ceiling rose to fan terminal by providing flexible cable three core Copper conductor of size 23/0.0076 (3 Core x 0.50 Sqmm), ISI marked and write down MES Number on fan by black paint/Marker complete all as specified and directed by Eng-in-Charge. |
| 173 | Item No 169 S&F Wall mounting fan of sweep fans complete with fixing accessories , 230 V, 50 Hz, 400 mm sweep, including providing electrical connection from ceiling rose to fan terminal and write down MES Number on fan by black paint/Marker complete all as specified and directed. |
| 174 | Item No 170 Supply and fix exhaust fan , steel/metal body AC single phase, 230 V of size 300 mm sweep with blades, frame and louvers complete all as specified and as directed. |
| 175 | Item No 171 Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. (Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted) |
| 176 | Item No 172 S & F for Highly efficient LED Inverter Bulbs, 09 W, used as a ready replacement for existing GLS/CFL direct fit lamp,in B-22 cap of make Bajaj, Havells, HPL complete all as specified and directed |
| 177 | Item No 173 Supply and fix in repairs Wall light fittings suitable for LED bulb including LED bulb of 7 watt, including connection with all necessary fixing accessories complete all as specified and directed by Engr-in-Charge. |
| 178 | Item No 174 Supply and fix in repairs integrated LED tube light fitting 1x18/20 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes including taking down the existing complete all as specified and directed. |
| 179 | Item No 175 S & F for Decorative ultra slim LED light fitting 2 feet 10 watts, 6500K batten aluminium extruded with end caps complete all as specified and as directed. |
| 180 | Item No 176 S & F for LED luminaire 600 mm x 600 mm square LED panel 35/36 watts, 220 volts, AC recessed type with high efficiency PMMA diffuser soft glare free light complete with drivers, holders, LED lamp suitable for roof ceiling, including connecting up with driver three core flexible copper conductor cases of suitable size complete all as directed by Engineer- in-charge. |
| 181 | Item No 177 S & F for Energy saving new generation 10 watts LED bulk head fitting IP 65 luminaire with opel diffuser pre wired with warranty option of 5 years from date of installation and necessary mounting arrangements , provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting including LED bulb complete all as specified and as directed. Havells Cat pt No. HEXAFT10WLED857SSYMBOPC or equivalent in Bajaj, Philips. |
| 182 | Item No 178 S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 30 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe 40 mm dia medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge. Cat No LHETAVU7PA7J030 or equivalent in Wipro |
| 183 | Item No 179 S & F for sheet metal enclosure MCB DB TPN 4 way, IP-43, IK 09 with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed. |
| 184 | Item No 180 S & F for metal clad box suitable for 230 volt 50 Hz for AC and Geser connection three pin and socket with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified and as directed complete all as specified and as directed |
| 185 | Item No 181 M&L for Sub main wiring in repairs with four runs of single core FR LS PVC insulated unsheathed cable 1100 volts grade, 6 Sqmm size with multistranded copper conductor, drawn in and including non metallic rigid PVC conduit of not less than 25 mm dia concealed in wall by cutting chases of wall and making good the disturbed surface, including PVC insulated unsheathed FR LS 6.0 Sqmm cable with multistranded copper conductor green PVC insulated as contineous earth conductor cable connected to earth dolly from main distribution board complete all as specified and directed by Engr-in-Charge Note:- four runs of 6 sqmm cable,two run of 6 sqmm cable and one run of PVC conduit will be measured as one unit |
| 186 | Item No 182 M&L for Sub main wiring in repairs with two runs of single core FR LS PVC insulated unsheathed cable 1100 volts grade, 4 Sqmm size with multistranded copper conductor, drawn in and including non metallic rigid PVC conduit of not less than 25 mm dia concealed in wall by cutting chases of wall and making good the disturbed surface, including PVC insulated unsheathed FR LS 4.0 Sqmm cable with multistranded copper conductor green PVC insulated as contineous earth conductor cable connected to earth dolly from main distribution board complete all as specified and directed by Engr-in-Charge. :- Note:- Two runs of 4 sqmm cable,one run of 4 sqmm cable and one run of PVC conduit will be measured as one unit |
| 187 | Item No 183 S & F for MCB Three pole and neutral rated capacity 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed. |
| 188 | Item No 184 S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed. |
| 189 | Item No 185 Earthing complete with galvanisedsteel earth plate electrode60×60cm.× 6mm thick, buried directly in ground (earth pit not lessthan 2.25 metres deep below ground level) with top edge of the plate notless'than 1.5 metres below normalground level, connected togalvanised earth lead wire 4.0mmdia by means of bolts, nuts, checknuts and washers of galvanised ironor steel all as shown in electricalplate No. 3 connected to earthing testpoint all as specified or indicatedincluding testing on completion.Note :- GI earth wire 4 mm dia and 15 mm dia protection pipe upto 7.5 mtr from earth plate is deemed to be included in rate quoted. |
| 190 | Item No 186 Supply assembly, erection, testing commissioning of indoor wall mounted panel frame size of mounted cubical type factory made IP 65 of environment friendly polycarbonate PC - GFS Insulation-enclosed power distribution board as power switchgear and control gear assembly (PSC) in accordance with IEC 61439-2wall mounted LT panel board with OEM Manufacturing certificate,Bottom parts and lids of the boxes made from impact-resistant polycarbonate, halogen and silicone-free, colour RAL 7035, transparent lid with quick action fasteners for tool operation. Burning behaviour according to IEC 60695-2-11 glow wire test + 960°C.Maximum water absorption 10 mg in accordance with DIN 53473. Protective measure: totally insulated (protection class II), the enclosure should have mechanical strength equivalent to IK10 (bidder should submit compliance for same for polycarbonate enclosure in OEM letterhead with technical bidding) suitable for 415V 3 phase 4 wire, 50HZ non metalic kiosk single door with the required provision for 3 switch gears and control gears along with the approved make. the LT panel including Sepratedcomparment for fixing of fourNosThree Phase &single phase meter and providing MCB,providing glass view for reading of meter complete fabrication shall be painted as per specification. Wall mounted LT panel board shall be complete with all standard accessories factory made with OEM manufacturing certificate & the type tests report as per CPRI ,including, phase indicating lamps control fuse unit, MV danger notice plate numbered/lettered and with comprising the following. Drawing from Original Equipment Manufacturing ( OEM )to be got approved from accepting officer before supply of Panel. ( Drawing from any other agency / System house will not be accepted. Panel should be manufactured and assembled by OEM only. Fabrication /Assembling from any other system house will not be accepted. The bidder should submit all relevant type test certificate / compliance in OEM letterhead during technical evaluation. The bidder should provide warranty / guarantee format in OEM letterhead. The bidder should submit Routine test certificate during order execution in OEM letterhead.Incoming : MCCB 125A, 4 pole, 25KA-1 No.,RYB Indication lamp, Digital Ampere Meter . Digital Volt Meter ,125A/5A,5VA,CL.1, CT – 3nos,Fuse Terminal Block with 2A Fuse-6nosOutgoing : connecting the following switch gear: (i) MCB, 40A FP amps, 415 volts, ‘C’ curve, 10 KA - 06 Nos (ii) MCB, 32A DP amps, 240 volts, ‘C’ curve, 10 KA - 02 Nos (iii) Fixing only 3phase serviceable existing electric meter- 06 Nos each |
| 191 | SCHEDULE \\"A\\" (Schedule of credit )Schedule of Credit Rs 367868.00 (Minus) inserted by the MES. (Note : Credit amount shall be deducted manually to arrive net amount) SCHEDULE OF CREDIT ADDN/ALTN & SPECIAL REPAIR TO CERTAIN BLDGS AT THE INF SCHOOL, MHOW S/No Description of item of work A/U Qty Rate Amount |
| 192 | Old Shutter with chowkhat only size N exc 1.50 sqm incl iron mongries |
| 193 | Old Shutter with chowkhat only size exc 1.50 sqm but not exc -4.0 sqm incl iron mongries |
| 194 | Old wire mesh |
| 195 | Old glass pane |
| 196 | Old aluminium fittings tower bolt, handle,sliding door bolt, etc |
| 197 | Old Aluminium alloy body door closer, floor spring, lever, etc |
| 198 | Old Curtain rod |
| 199 | Old Brick work |
| 200 | Old tiles |
| 201 | Old water tank 500 ltr |
| 202 | Old water tank 1000 ltr |
| 203 | Old GI pipe 15mm bore |
| 204 | Old GI pipe 20mm bore |
| 205 | Old looking mirror |
| 206 | Old pvc conncetion / PVC cupling/ Gratings |
| 207 | Old bib tap,two way bib tap, pillar tap,stop valve,angle valve, two way angle valve, shower |
| 208 | Old towel rail / towel ring, paper holder, soap disc |
| 209 | Old flushing cistern |
| 210 | Old jet spary / Health faucet |
| 211 | Old stone slab/concrete tile/paver tiles |
| 212 | Old Unsv Gate valve |
| 213 | Old unsv grating of any type |
| 214 | Old unsv PVC Pipes 75/110 mm dia |
| 215 | Old boarding/ false ceilng |
| 216 | Old S/S sink, plate rack |
| 217 | Old AC Sheet |
| 218 | Old wall/ WHB Mixture |
| 219 | Old point wiring such as PVC cable with out batten/ conduit and MS box as existing fo light, fan socket and power point. |
| 220 | Old Unsv switch, sockets, ceiling rose, bell, bell push, lamp holder etc |
| 221 | Old Unsv fan regulator |
| 222 | Old Unsv sub main wiring/cable of any size |
| 223 | Old Unsv MCB DB TPN/SPN any type |
| 224 | Old Unsv MCB SP/ SPN |
| 225 | Old Unsv tube light fittings of any type |
| 226 | Old Unsv light fittings of any type |
| 227 | Old Unsv security light fittings of any type |
| 228 | Old Unsv Meter Panel |
| 229 | Old Unsv Earthing |
| 230 | Old Unsv LT Service cable 3.5 core of any size of any description Total : 367868.0 Notes :- (a) All quantities shown under column 4 are provisional and may vary during execution. Actual amount of credit shall be worked out based on rates inserted under Col. 5 of Schedule of credit. (b) Tenderers are advised to inspect the old material/ items at site and ascertain their condition. It shall be deemed that the contractor has made himself well aware and ascertained the condition of these items whether he inspects them or not. No claim whatsoever on this account shall be admissible by the Government. The mode of measurement shall be same as for the work to executed. tenderers are requested to verify the condition of the materials, any dispute arises at later stage will not be entertained. (c) The items as indicated in Schedule of credit shall be the property of the contractor. The total amount of Schedule of credit shall be deducted from total of Schedule „A' [BOQ] to arrive at Contract Sum. (d) The rates inserted under Column 5 are firm and the contractor shall have no claim what so ever against the department if the actual value of dismantled materials turns out to be different from the cost given by the department. (e) All above materials shall be recorded in MB jointly by Engineer-in -Charge and contractor. (f) No rebate on Schedule of credit shall be accepted. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysNov 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 28 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender