Tender for Tender for Construction Of A Convention Centre In Mauja Jatepur, Ward No. 22, Jatepur. Please Refer Tender Documents.
Tender Value
3.26 Crore
Estimated cost
Bid Submission
28 Oct 2026
2 days left
EMD
16.35 Lakhs
Bank guarantee accepted
Document Fee
5900
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Gorakhpur → Uttar Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of A Convention Centre In Mauja Jatepur, Ward No. 22, Jatepur. Please Refer Tender Documents.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.(DSR-2.80) |
| 2 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:(DSR-4.1) |
| 3 | 1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)(DSR-4.1.8) |
| 4 | 1:2:4 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources)(DSR-4.1.3) |
| 5 | Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of concrete.: |
| 6 | Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement. (DSR-5.33.1) |
| 7 | All work upto plinth level: Concrete of M25 grade with minimum cement content of 300 kg /cum (DSR-5.33.1.1) |
| 8 | All work above plinth level upto v floor Concrete of M25 grade with minimum cement content of 300 kg /cum (DSR-5.33.2.1) |
| 9 | Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete Thermo-Mechanically Treated bars of grade Fe-500D or more. DSR-5.22.6 |
| 10 | Centering and shuttering including strutting, propping etc. and removal of form for |
| 11 | Foundations, footings, bases of columns, etc. for mass concrete (DSR-5.9.1) |
| 12 | Columns, Pillars, Piers, Abutments, Posts and Struts Stairs, (excluding landings) except spiral-staircases (DSR-5.9.6) |
| 13 | Lintels, beams, plinth beams, girders, bressumers and cantilevers (DSR-5.9.5) |
| 14 | SLAB (DSR-5.9.20) |
| 15 | EDGE OF SLAB (5.9.16.1) |
| 16 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in (DSR-6.1) |
| 17 | Cement mortar 1:4 (1 cement : 4 coarse sand) (DSR-6.1.1) |
| 18 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:4 (1 cement : 4 coarse sand) (DSR-6.4.1) |
| 19 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. SUPERSTRUCTURE (BUILDING GF+FF ) (6.13.2) |
| 20 | Earth work in filling etc complete AS PER Approved rate (AR) |
| 21 | CEMENT PLASTER (IN COARSE SAND) 12 mm cement plaster of mix : (DSR-13.4..1) |
| 22 | 12 mm cement plaster of mix : (DSR-13.4..1) |
| 23 | Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. (DSR-13.9.1) |
| 24 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (DSR-13.80) |
| 25 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : (DSR-13.48) |
| 26 | Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm (DSR-13.48.1) |
| 27 | Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/10 sqm of approved brand and manufacture (DSR-13.48.2) |
| 28 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture (DSR-13.48.3) |
| 29 | Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all ecessary fittings complete, including applying a priming coat of approved steel primer. Using flats 30x6mm for diagonal braces and central cross piece (DSR-10.5.2) |
| 30 | Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. (DSR-10.31) |
| 31 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. (DSR-10.16) |
| 32 | Hot finished welded type tubes (DSR-10.16.1) |
| 33 | Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (DSR-8.31) |
| 34 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Size of Tile 600 x 600 mm (*DSR-11.41A.3.1) |
| 35 | Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete (DSR-11.39). |
| 36 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hingeswith necessary screws (DSR-9.21.1) |
| 37 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): (DSR-21.3) |
| 38 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm (DSR-21.3.2) |
| 39 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab all colour and texture except black, Cherry/Ruby red Area of slab upto 0.50 sqm (DSR-8.2.3.1 ) |
| 40 | Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of specified operations including applying slurry of cement, laying brick bats with mortar, applying a second coat of cement slurry, and finishing the surface with 20 mm thick jointless cement mortar admixed with water proofing compound, including laying glass fibre cloth and making pattern of 300x300 mm square 3 mm deep. The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. With average thickness of 120 mm and minimum thickness at khurra as 65 mm. Work shall be carried out as per directions of the Engineer-in-Charge. (DSR Item 22.7.1) |
| 41 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. (12.22) |
| 42 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (DSR-22.5) |
| 43 | Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401. (ANALYSIS OF RATE) |
| 44 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required: White Vitreous china Orissa pattern W.C. pan of size 580x440mm with integral type foot rest (D.S.R. 17.1.1/2023) |
| 45 | Providing and fixing white vetreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C.flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid (D.S.R. 17.3.1) |
| 46 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : (DSR-17.5.2) |
| 47 | Providing and Fixing of counter basin (550 x 450x 200 mm ) cascode NXT CO 431 (ANALYSIS OF RATE) |
| 48 | Providing and Fixing of wall hung wash basin (450 x 350x 150 mm ) cascode UNO C042 L (ANALYSIS OF RATE) |
| 49 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washerscomplete. (DSR-17.31) |
| 50 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge (DSR-17.16A) |
| 51 | Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. (DSR-17.22 A) |
| 52 | Providing and fixing CP Brass SINGLE LEVER Teliphonic wall mixer as per the direction of Engineer-in-charge. 15mm nominal dia (DSR-17.22 A) |
| 53 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. 40 mm dia (DSR-17.28.1.2 ) (DSR-17.28) |
| 54 | Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. (DSR-17.33) |
| 55 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and makinggood the same including testing of joints complete as per directionof Engineer in Charge. (DSR-18.8) |
| 56 | CPVC 20 MM Nominal dia pipes(DSR NO 18.8.2/2023) |
| 57 | CPVC 25 MM Nominal dia pipes(DSR NO18.8.3/2023) |
| 58 | CPVC 32 MM Nominal dia pipes(DSR NO18.8.4/2023) |
| 59 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. (DSR-18.9) |
| 60 | CPVC 40 MM Nominal dia pipes(DSR NO 18.9.5/2023) |
| 61 | CPVC 50 MM Nominal dia pipes(DSR NO 18.9.6/2023) |
| 62 | Providing and fixing uplasticised PVC connection pipe with brass unions :(DSR-18.21.2.1) |
| 63 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflowpipes but without fittings and the base support for tank. (DSR-18.48) |
| 64 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : (DSR-18.49.1) |
| 65 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms (DSR-18.51) |
| 66 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore (DSR-18.53.1 ) |
| 67 | Providing and fixing C.P. Brass extension nipple (size 15mmx50mm)of approved make and quality as per direction of Engineer-in-charge. (DSR-18.53A) |
| 68 | C.P Jali 110mm (AR) |
| 69 | P.V.C pipe 160 mm 6 kg pressure I.S.I make (AR) |
| 70 | P.V.C pipe 110 mm 6 kg pressure I.S.I make (AR) |
| 71 | Providing and fixing of trap self cleaning design (AR) |
| 72 | Providing and fixing of PVC Coupler 160mm dia (AR) |
| 73 | Providing and fixing of Y- arm 110 mm (ANALYSIS OF RATE) |
| 74 | Providing and fixing of T 110 mm (ANALYSIS OF RATE) |
| 75 | Providing and fixing of door T (ANALYSIS OF RATE) |
| 76 | Providing and fixing of 160 mm Band (ANALYSIS OF RATE) |
| 77 | Providing and fixing of 160 mm T (ANALYSIS OF RATE) |
| 78 | Providing and fixing of 160X110mm Reducer (ANALYSIS OF RATE) |
| 79 | Providing and fixing of 110mm Door band (ANALYSIS OF RATE) |
| 80 | Providing and fixing of 110mm Plain band (ANALYSIS OF RATE) |
| 81 | Providing and fixing of 110mm Cowl (ANALYSIS OF RATE) |
| 82 | Providing and fixing of PVC Gate Valve (ANALYSIS OF RATE) |
| 83 | 25mm dia |
| 84 | 40mm dia |
| 85 | 50mm dia |
| 86 | S.I.T.C. of ready made septic Tank for 80 user with primeary (1200mm dia & 2500mm depth) the secondry tank (600mm dia & 1250 depth) top to be costed in 1:2:4 R.C.C. slab 125mm thick with 600mm dia inspection chamber and 100mm dia vent pipe from the main chamber. |
| 87 | Installation of submersible pump set and fixing of 1hp KSB/Cropmton 1.5mm sq 3 core submersible cable electric control panel, steel wire rope, GI pipe boring of 110mm dia PVC pipe, steiner jali etc. all complete including supply of all materials, labour & T&P etc. required for proper completion of the work. (Approved Rate) |
| 88 | P/F hexazonal Fan box (Electrical SOR-1149)/2018 |
| 89 | Wiring point for light with PVC conduit with 1.5 sq. mm. FR PVC insulated multistrand copper conductor cable as earthwire drawn inside the conduit.pipe partly concealed in the wall and partly laid slab alongwith the reinforcement before concreting, complete with 8 SWG GI earth continuity wire, piano type switch and ceiling rose/angle/ batten holder on 3 mm. thick phenolic laminated backlite sheet etc. complete in all respect, as directed including matching colour wash. (S.I.No-138(C) ) |
| 90 | Supply and wiring of submain in 20 mm dia heavy duty (2mm thick) PVC conduit with one number 2.5 sq. mm. FR PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit.concealed in wall and partly laid in slab alongwith reinforcement before concreting, with one number 8 SWG GI earth continuity wire including matching with colour wash etc, complete in all respect. (S.I.No-221(C) ) |
| 91 | Supply and wiring of submain in 25 mm dia heavy duty (2mm thick) PVC conduit with one number 6.sq. mm.(S.I NO -222(C)) |
| 92 | Supply and wiring of submain in 20 mm dia heavy duty (2mm thick) PVC conduit with one number 6.sq. mm.(S.I NO -223(C)) |
| 93 | S&F surface/flush mounting 8 ways TPN-DB box with additionl metel door CAT B (S.I NO 1028 A) |
| 94 | S&F surface/flush mounting 4 ways SPN-DB box with additionl metel door CAT B (S.I NO 1022 A) |
| 95 | supply and fixing of 6AMP to 32 AMP MCB (10 KA) (S.I.N0-1002 |
| 96 | Plug Powar point (SOR 1039 A) |
| 97 | FAN CELLING 1200 MM (MR) |
| 98 | S&F of 63 Amp.4 Pole Isolator CAT.B (S.I.No-1007(A) |
| 99 | S&F of 63 Amp D.P Isolator 1005 b |
| 100 | WIRING POINT FOR FAN CAT B (SOR 140 (C) |
| 101 | LED Tube light CAT AA (SOR 1413( A) |
| 102 | LED Bulb 12 Watt OF Approved brand |
| 103 | Wiring for light point (SOR 138(C) |
| 104 | WIRING POINT FOR PLUG (SOR 140 (C) |
| 105 | Regulater PWD SOR ELECT 1203 © 571.0/NO |
| 106 | Aluminiam cable 16 mm 4 CORE 503 (I) |
| 107 | Modular Switch for plug (AR) |
| 108 | Modular Switches for exaut fan /light (AR) |
| 109 | Supply and burring of safe Earthing electcrode t-19 SOR 2018/725(A) |
| 110 | Earthing electrade (SOR ELECT 725 (A) |
| 111 | Supply of wall mounted Up-Down Light Gray pure polyester powder coated, Pressure die-cast aluminium housing for efficient thermal management, sturdiness & excellent corrosion resistance. The housing should be IP66 protection for high reliability in outdoor applications. High efficiency long life COB LED mounted on MCPCB on opposite ends of fixture. Lumen efficacy of LED >140 lm/W. High quality toughened glass in clear finish for uniform light distribution Upward & downward light ratio-50:50 and high impact resistance IK07. The Fixture should have Built-In potted, electronic driver (SMPS based constant current supply) with THD<10 & PF> 0.985, Open/ Short circuit protection & other safety test as per IS:15885 Part 2/Sec 13. The length of the fixture should not be more than 310mm and width not more than 100mm total system lumen output should not be less than 2500 lumen in CCT of 3000K CRI>80 with system wattage not exceeding 25W.Supply of wall mounted up-down light gray pure polyyester powder coated |
| 112 | 10 MM Polycarbonate roofing sheet (GDA approved Lake view appartment,manbela convention center) |
| 113 | Casement window double panels with fixed mullion with s s 304 friction hinges as per soze and weight of ssh multi-point locking system zinc alloy powder coated handles hight above 1.8 meter UPVC WINDOW (DSR-9.147.A2.2/2023) |
| 114 | P/A pop on column including punning and applying chemical M.R (Manbela convention centar) |
| 115 | S/F OF Jhumer M.R (Manbela convention centar) |
| 116 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia help of dry wall screws of size 3.5 x 25mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, gril with 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) (D.S.R 12.45.1/2023) |
| 117 | P/A of mural painting on hall wall including all polishing and finishing work (Manbela convention centar) |
| 118 | Profile light (Manbela convention centar) |
| 119 | S/F of Wooden door front gate (Manbela convention centar) |
| 120 | S/F of wooden door openig lenth 2.1x1.5m gate |
| 121 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.) DSR-10.28/2023 |
| 122 | Providing and laying factory made chamfered edge cement concrete paver blocks in footpath 80 mm thick c.c paver block of M-40 grade with approved colour design and pattern (AR) |
| 123 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and nontoxicadditives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58N/mm2, modulus of elasticity 900N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and… |
| 124 | Providing and fixing of PCD aluminium body LGP &PMMA CANCEL light 12w (MR) Piru saeed convevtion center |
| 125 | S&F surface/flush mounting 12 ways SPN-DB box with additionl metel door CAT B (S.I NO 1025 A) |
| 126 | S&F of 125 Amo 4pole MCCB(1021A) |
| 127 | Same as above but for fan/fresh air fan (light duty exhaust fan) Point (S.I.No-140(C) ) |
| 128 | Add for inverter wiring in wiring for light Fan/Plug with 1.5mm copper wire SOR Electrical work (189A)/2018 |
| 129 | Tower bolt (sor no 4-item no -10) |
| 130 | Tower bolt with 10 mm dai rod and screw 200mm long |
| 131 | Silding bolt 16 mm dia rod and 250 mm long |
| 132 | Door handle with screws 150 mm long |
| 133 | Providing and fixing Of fallowing PVC PIPE And fittings |
| 134 | P.V.C pipe 160 mm 6 kg pressure I.S.I make (AR) |
| 135 | p.V.C pipe 110 mm 6 kg pressure I.S.I make (AR) |
| 136 | P.V.C 75mmdia 6 kg pressure I.S.I make (AR) |
| 137 | HORTICULTURE |
| 138 | Grass(maxican)AR |
| 139 | paam AR |
| 140 | champa AR |
| 141 | terminalia AR |
| 142 | cycas AR |
| 143 | Stone work plain ashlar in domes in super structure upto floor v level in cement mortar 1.3(1 cement 3 coarse sand ) including centering shuttering and pointing with white cement mortar 1:2 (1 white cement 2 stone dust ) with an admixture of pigment matching the stone shade |
| 144 | Ornamental work both face dressed white sand stone DSR-7.14.2.2 |
| 145 | For Ornamental fountain all fitting work |
| 146 | Providing and fixing sloping chajja of stone 40mm think and upto 80cm wide beyond the wall as measurred along the slone in cement mortar 1:4 with 12 mm diameter anchoring steel ber 45 cm long fixed in each stone and supprted on and including with bricks cove in cement mortar 1.4 including pointing in cement mortar 1:2 (1 white cement 2 stone dust ) with an admixture of pigment matching the stone shade Red sand stone with common burnt clay F.P.S (non modular) bricks of class designation 7.5(DSR-7.28.1/2023) |
| 147 | Providing and fixing horizontal chajja of stone 40 mm think and upto 80 cm projection in cement mortar 1.4 (1 cement 4 coarse sand) including pointing in wtite cement mortar 1:2 (1 white cement 2: stone dust) with an admixture of oigment matching the stone shade Red sand stone (DSR-7.29.1/2023) |
| 148 | 30 mm red sand stone sun-shade (chisel-dressed) supported on red sand stone brackets fixed in walls with cement mortar 1:4 (1 cement 4 coarse sand) including finishing complete.(DSR-7.30/2023) |
| 149 | Providing and fixing red sand stone brackets 55x22.5x45 cm sunk and moulded including provoding and foxing with 4 nas gun metar cramp 25v6 33 30 cm long(DSR-7.31/2023) |
| 150 | Stone work plain in coping cornices string courses and plinth courses upto 75 mm thick in cement mortar 1:6 with an admixture of pigment matching the stone shade red sand stone(DSR-7.32.1/2023) |
| 151 | Providing and fixing stone jali 40mm thick throughout in cement mortar 1:3 including pointing in white cement mortar 1:2 (1 white cement 2 stone dust) with an admixture of pigment jali slab without any chamfers etcred sand stone(DSR-7.33.1/2023) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 2 daysOct 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender