Tender For Operation, Repair And Maintenance Of Borewell, Booster Pump, Electric Panels, Oht And Sump At Nsg Manesar For The Year-2026-27 (Sh: Work On Contract Basis)
Tender Value
62.44 Lakhs
Estimated cost
Bid Submission
21 Oct 2026
0 days left
EMD
1.24 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Gurgaon → Haryana
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Operation, Repair And Maintenance Of Borewell, Booster Pump, Electric Panels, Oht And Sump At Nsg Manesar For The Year-2026-27 (Sh: Work On Contract Basis)
BOQ
| Sl. No. | Item Description |
| 1 | Preventive Maintenance of the Pumps Make KBL as per Pump List Attached. The agency will undertake the maintenance work of the pumps only through the OEM or OEM authorized dealer. |
| 2 | Model & Make |
| 3 | SHM150/32N |
| 4 | SHM80/40 N |
| 5 | UP 100/38 |
| 6 | UP80/38 or UP 80/30 |
| 7 | SP2HM |
| 8 | KDS1040+ |
| 9 | KDS1550+ |
| 10 | DB 40/26 |
| 11 | DB XE 40/26 |
| 12 | Scope of work covered under the preventive maintenence |
| 13 | a) One visit in an year will be made by an OEM (KBL) service person with prior intimation. |
| 14 | b)One breakdown visits included under AMC. |
| 15 | c) Complete check-up of the Pump sets as per KBL standards. |
| 16 | d) Check free rotation of pumps. |
| 17 | e) Check tightness of casing bolts, Foundation bolts, and Grease MS Fasteners. |
| 18 | f) Oil levels, grease in bearings, Condition of bearing to be checked and replenished if required(Spare shall be provided by deptt) |
| 19 | g)Vibration, Noise, Bearing Temperature, Voltage, Speed and pressure to be measured and recorded. |
| 20 | h)Alignment of pump set to be checked and in case if required rectification to be carried out and readings to be recorded. |
| 21 | i)Coupling bushes, pins, rubber parts to be checked and to be replaced if required.(Spare shall be provided by deptt) |
| 22 | j)Mechanical seal condition to be checked and suitable recommendations to be made. |
| 23 | k) Service report will be generated after every visit recording data and details of above checks. |
| 24 | l)Training will be provided to site operators to obtain optimum output & life of equipment. |
| 25 | Overhauling Charges of the following Pump including Dismentaling, Machining , Oiling , Greasing , Assembling & Installation at Site including loading and unloading, to and fro transportation of pump from NSG Campus Manesar to the workshop. The work will be done through the OEM or OEM-authorized dealer of the pumps, and the repair work will be given a three-month warranty by the OEM/authorized dealer. |
| 26 | Model & Make:- |
| 27 | SHM150/32N |
| 28 | SHM80/40 N |
| 29 | UP 100/38 |
| 30 | UP80/38 or UP 80/30 |
| 31 | SP2HM |
| 32 | KDS1040+ |
| 33 | KDS1550+ |
| 34 | DB 40/26 |
| 35 | DB XE 40/26 |
| 36 | Replacement of the following spare parts of the existing KBL Pump SHM 150/32 N 'Kirloskar' make main fire pump drive by electric motor with a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required. The work will be done through the OEM or OEM-authorized dealer of the pumps, and the repair work will be given a three-month warranty by the OEM/authorized dealer. |
| 37 | Enclosed Impeller (SHM 150/32N) |
| 38 | Pump Shaft Karban QTY 12 |
| 39 | Casing Ring |
| 40 | Spacer for Cartridge |
| 41 | Casing Cover |
| 42 | Clamping Plate |
| 43 | Split Lantern Ring |
| 44 | Split Gland |
| 45 | Liquid Deflector |
| 46 | BRG housing |
| 47 | Bearing Cartridge |
| 48 | Set of Bearing |
| 49 | Bearing Cover- PS |
| 50 | Eye Bolt- M 12X22L |
| 51 | Shaft Sleeve |
| 52 | Set of Keys |
| 53 | IMpeller Nut with Helicoil Insert |
| 54 | Round Lock Nut-M55 |
| 55 | St Box Bush |
| 56 | Lock Washer -55D-Nom |
| 57 | Gland Paking -12mm Sq |
| 58 | Grease Nipple-1/4BSP |
| 59 | Grease Nipple-1/4BSP |
| 60 | Insp Hole Cover |
| 61 | Set of oil Seal |
| 62 | Set of Gasket |
| 63 | Cooling Chaber |
| 64 | Set of 'O' Ring |
| 65 | Set of Fastner |
| 66 | Cooling Pipe |
| 67 | Replacement of the following spare parts of the existing KBL Pump UP80/38 'Kirloskar' make main fire pump drive by electric motor with a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required. The work will be done through the OEM or OEM-authorized dealer of the pumps, and the repair work will be given a three-month warranty by the OEM/authorized dealer. |
| 68 | Impeller (80/38) |
| 69 | Pump Shaft Karban QTY 18 |
| 70 | Casing Ring |
| 71 | Shoulder Ring |
| 72 | Gland |
| 73 | Lantern Ring |
| 74 | Liquid Deflector-34D |
| 75 | Brg.Hgs DE-Mrtric |
| 76 | Bearing Housing NDE |
| 77 | Brg-6306 C3 SKF or Eq DE & NDE |
| 78 | Shaft Sleeve(DE&NDE) |
| 79 | Bearing Lock Nut M30X1.5RH |
| 80 | Lock Washer -55D-Nom |
| 81 | Gland Paking -10mm Sq |
| 82 | Set of Keys |
| 83 | Set of 'O' Ring |
| 84 | Set of Gasket |
| 85 | Set of Fastner |
| 86 | Cooling Pipe |
| 87 | Replacement of the following spare parts of the existing KBL Pump UP 100/38 'Kirloskar' make main fire pump drive by electric motor with a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required. The work will be done through the OEM or OEM-authorized dealer of the pumps, and the repair work will be given a three-month warranty by the OEM/authorized dealer. |
| 88 | Impeller (100/38) |
| 89 | Pump Shaft Karban QTY 12 |
| 90 | Casing Ring |
| 91 | Shoulder Ring |
| 92 | Gland |
| 93 | Lantern Ring |
| 94 | Liquid Deflector-34D |
| 95 | Brg.Housing DE-Modi |
| 96 | Bearing Housing NDE |
| 97 | BEG-REP Make-6309 C3 |
| 98 | Shaft Sleeve |
| 99 | Lock Nut -M45X1.5Rh |
| 100 | Lock Washer -45D-Nom |
| 101 | Gland Paking -12mm Sq |
| 102 | Set of Keys |
| 103 | Set of 'O' Ring |
| 104 | Set of Gasket |
| 105 | Set of oil Seal |
| 106 | Set of oil Seal |
| 107 | Set of Fastner |
| 108 | Cooling Pipe |
| 109 | Replacement of the following spare parts of the existing KBL Pump SHM 80/40N 'Kirloskar' make main fire pump drive by electric motor with a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required. The work will be done through the OEM or OEM-authorized dealer of the pumps, and the repair work will be given a three-month warranty by the OEM/authorized dealer. |
| 110 | Impeller (SHM 80/40 N) |
| 111 | Pump Shaft Karban QTY 12 |
| 112 | Casing Ring |
| 113 | Spacer for Cartrideg |
| 114 | Casing Cover |
| 115 | Calmping Plate |
| 116 | Split Lantern Ring |
| 117 | Split Glnad |
| 118 | Liquid Deflector |
| 119 | BRG Housing |
| 120 | beraing Cartrideg |
| 121 | Set of Bearing |
| 122 | Bearing Cobver -PS |
| 123 | EYE Bolt M12X22L |
| 124 | Shaft Sleeve |
| 125 | Set of Keys |
| 126 | Impellet Nut with Helicil Insert |
| 127 | Round Lock nut M55 |
| 128 | ST Box Bush |
| 129 | Lock Washer -55D-Nom |
| 130 | Gland Paking -12mm Sq |
| 131 | Grease Nipple-1/4BSP |
| 132 | Grease Nipple-1/4BSP |
| 133 | Insp Hole Cover |
| 134 | Set of oil Seal |
| 135 | Set of Gasket |
| 136 | Cooling Chaber |
| 137 | Set of 'O' Ring |
| 138 | Set of Fastner |
| 139 | Cooling Pipe |
| 140 | Replacement of the following spare parts of the existing KBL Pump SP 6L 'Kirloskar' make main fire pump drive by electric motor with a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required. The work will be done through the OEM or OEM-authorized dealer of the pumps, and the repair work will be given a three-month warranty by the OEM/authorized dealer. |
| 141 | Pump Shaft (CS) |
| 142 | Shaft Sleeve |
| 143 | Gland Plate(CI) |
| 144 | Ball Bearing |
| 145 | impeller ( CI) |
| 146 | Set of Gasket |
| 147 | Set of fasteners |
| 148 | Bearing Housing (CI) |
| 149 | Liquid Deflector (NTR) |
| 150 | coupling tyre type |
| 151 | Replacement of the following spare parts of the existing KBL Pump SP 2HM 'Kirloskar' make main fire pump drive by electric motor with a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required. The work will be done through the OEM or OEM-authorized dealer of the pumps, and the repair work will be given a three-month warranty by the OEM/authorized dealer. |
| 152 | Shaft Sleeve |
| 153 | Gland Plate(CI) |
| 154 | Ball Bearing |
| 155 | impeller ( CI) |
| 156 | Set of Gasket |
| 157 | Set of fasteners |
| 158 | Liquid Deflector (NTR) |
| 159 | Replacement of the following spare parts of the existing KBL Pump KDS 1040 'Kirloskar' make main fire pump drive by electric motor with a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required. The work will be done through the OEM or OEM-authorized dealer of the pumps, and the repair work will be given a three-month warranty by the OEM/authorized dealer. |
| 160 | Pump Shaft (CS) |
| 161 | Shaft Sleeve |
| 162 | Gland Plate(CI) |
| 163 | Ball Bearing 6307 |
| 164 | Ball Bearing 6308 |
| 165 | impeller ( CI) |
| 166 | Set of Gasket |
| 167 | Set of fasteners |
| 168 | Mounting Casing (CI) |
| 169 | NDE Cover |
| 170 | Delievery Casing |
| 171 | Mechanical Seal |
| 172 | Seal Plate |
| 173 | Gland Packing |
| 174 | Liquid Deflector (NTR) |
| 175 | Replacement of the following spare parts of the existing KBL Pump KDS 1050+ 'Kirloskar' make main fire pump drive by electric motor with a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required. The work will be done through the OEM or OEM-authorized dealer of the pumps, and the repair work will be given a three-month warranty by the OEM/authorized dealer. |
| 176 | Pump Shaft (CS) |
| 177 | Shaft Sleeve |
| 178 | Gland Plate(CI) |
| 179 | Ball Bearing 6307 |
| 180 | Ball Bearing 6308 |
| 181 | impeller ( CI) |
| 182 | Set of Gasket |
| 183 | Set of fasteners |
| 184 | END Cover |
| 185 | Mounting Casing (CI) |
| 186 | Delievery Casing |
| 187 | Mechanical Seal |
| 188 | Seal Plate |
| 189 | Gland Packing |
| 190 | Liquid Deflector (NTR) |
| 191 | Replacement of the following spare parts of the existing KBL Pump DB 40/26 'Kirloskar' make main fire pump drive by electric motor with a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required. The work will be done through the OEM or OEM-authorized dealer of the pumps, and the repair work will be given a three-month warranty by the OEM/authorized dealer. |
| 192 | Pump Shaft (CS) |
| 193 | Shaft Sleeve |
| 194 | Gland Plate(CI) |
| 195 | Ball Bearing 6305-SKF |
| 196 | Ball Bearing 6305-SKF |
| 197 | impeller ( CI) |
| 198 | Set of Gasket |
| 199 | Set of fasteners |
| 200 | Lantern Ring Nylon |
| 201 | Wear Ring Suction Side Ci |
| 202 | Bearing Housing -CI |
| 203 | Mechanical Seal with SS Plate |
| 204 | Impeller Nut-SS410 |
| 205 | Gland Packing |
| 206 | Liquid Deflector (NTR) |
| 207 | Bearing Cover DE -CI |
| 208 | Set of Keys |
| 209 | Replacement of the following spare parts of the existing KBL Pump DB XE 40/26 'Kirloskar' make main fire pump drive by electric motor with a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required. The work will be done through the OEM or OEM-authorized dealer of the pumps, and the repair work will be given a three-month warranty by the OEM/authorized dealer. |
| 210 | Pump Shaft (CS) |
| 211 | Shaft Sleeve SS410 |
| 212 | Gland Plate(CI) |
| 213 | Ball Bearing 6305-SKF |
| 214 | Ball Bearing 6305-SKF |
| 215 | impeller ( CI) |
| 216 | Set of Gaskets |
| 217 | Set of fasteners |
| 218 | Lantern Ring Nylon |
| 219 | Wear Ring Suction Side Ci |
| 220 | Bearing Housing -CI |
| 221 | Mechanical Seal with SS Plate |
| 222 | Impeller Nut-SS410 |
| 223 | Gland Packing |
| 224 | Liquid Deflector (NTR) |
| 225 | Bearing Cover DE -CI |
| 226 | Set of Keys |
| 227 | Rewinding of motors including all necessary material and of the same characteristics as original with required size of super enameled copper wire and F class insulation material including dismantling, removing of burnt wires, cleaning of slots, varnishing, assembling, greasing, testing including loading and unloading, to and fro transportation of pump from NSG Campus Manesar to the workshop etc. complete as required including credit for old scrap material which will be retained by the contractor etc., complete as required. The work will be done through the OEM or As per site available make, and the repair work will be given a three-month warranty by the OEM/authorized dealer. |
| 228 | Preventive Maintenance of the Blower Model No 5175 Everest as per Blower List Attached. The agency will undertake the maintenance work of the Blower only through the OEM or OEM authorized dealer. |
| 229 | Everest Blower Model 5175 |
| 230 | Scope of work covered under the preventive maintenence |
| 231 | a) Two preventive maintenance visit by OEM person in every six month with prior intimation. |
| 232 | b) Two breakdown visits included under AMC. |
| 233 | Replacement of the following spare parts of the existing Blower Model No 5175 'Everest' drive by electric motor 11KW/15HP capacity with a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required.The work will be done through the OEM or OEM-authorized dealer of the pumps, and the repair work will be given a three-month warranty by the OEM/authorized dealer. |
| 234 | Set of Rotor & Shaft |
| 235 | Set of Gear with Hub (Complete with Hardware) |
| 236 | Set of Bearing |
| 237 | Suction Air Filter |
| 238 | Set of Piston Bush |
| 239 | Pulley Spacer Bush |
| 240 | Set of Oil seal & O'Rings |
| 241 | Set of Vee-Belts |
| 242 | Oil Level Indicator |
| 243 | Set of Gaskets |
| 244 | Relief Valve |
| 245 | Oil Splasher Disc |
| 246 | Pressure Guage |
| 247 | EBBO Mineral oil |
| 248 | Supplying & Replacing of the rubber gasket(Minimum thickness 4mm) with undermentioned size with new one in the existing valves flange /Strainer (Nut & Bolt rate will be paid saperately) |
| 249 | Rubber Gaskets 80 mm dia |
| 250 | Rubber Gaskets 100 mm dia |
| 251 | Rubber Gaskets 150 mm dia |
| 252 | Rubber Gaskets 200 mm dia |
| 253 | Rubber Gaskets 250 mm dia |
| 254 | Rubber Gaskets 300 mm dia |
| 255 | Coupling Guard Size No Range 09-13 |
| 256 | Charges for Either lowering or Lifting of various capacity submersible pump set/Heavy Material/Machine either manually or using lifting machine including replacement of old nut , bolt, washer and gasket etc as reqd |
| 257 | Rewinding of submersible monoblock /openwell motor including all necessary material and of the same characteristics as original with required size of polyrapede insulated suitable guage copper conductor wire including dismantling, removing of burnt wires, cleaning , assembling, greasing, testing etc. complete as required including credit for old scrap material which will be retained by the contractor etc., complete as required. The work will include dismantling the motor from the site , loading, carrying repair work, to & fro movement between site and workshop ,unloading, reinstallation, connection and testing etc |
| 258 | Dismentling the Submersible Motor , taking out the rotor & carrying lathe work , turning & grinding work & fixing back to submersible etc required |
| 259 | Replacement of the following spare parts in the Submersible motor with a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required. |
| 260 | Brass Bush Complete Set(four nos in each set) |
| 261 | Thurst Plate Set |
| 262 | Dismentling, checking and re-assembling the same the Submersible Pump ,replacing the defective spare part (payment of spare parts will be paid saperately) machining ,grinding ,greasing , assembling , testing etc required (Warranty-03 Months) |
| 263 | Replacement of the following spare parts in the Submersible Pump of assorted stage & HP with a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required. |
| 264 | Shaft(SS) |
| 265 | Impeller(Plastic) |
| 266 | Guide Bush |
| 267 | Neck Ring(Rubber) |
| 268 | Top Bush (Brass) |
| 269 | Bowl(CI) |
| 270 | SS Sleeve-DOS |
| 271 | Set of Nut-Bolt (MOC-SS)Per Bowl |
| 272 | Coupling(MOC-SS)-1 |
| 273 | Impeller(steel) |
| 274 | Impeller(Plastic) |
| 275 | Guide Bush |
| 276 | Neck Ring(Rubber) |
| 277 | Top Bush (Brass) |
| 278 | Bowl(CI) |
| 279 | SS Sleeve-DOS |
| 280 | Set of Nut-Bolt (MOC-SS)Per Bowl |
| 281 | Coupling(MOC-SS)-1 |
| 282 | Supplying, installation, testing and commissioning of undermentioned HP multi stage submersible pump set, in bore well (stage, LPM & Head of the submersible will be decided by Engg in Charge ) complete with coupled totally enclosed electric motor suitable for 415 volt, 50 Hz, 3 phase A. C. supply including water proof jointing of cables. (excluding lowering charges- lowering charges of submersible pumpset will be paid separately) including credit for old scrap material which will be retained by the contractor etc., complete as required. |
| 283 | 3 HP multistage Submersible Pump Set(three phase) |
| 284 | 5 HP multistage Submersible Pump Set(three phase) |
| 285 | 7.5HP multistage Submersible Pump Set(three phase) |
| 286 | 10 HP multistage Submersible Pump Set(three phase ) having star delta connection |
| 287 | 12.5 HP multistage Submersible Pump Set(three phase ) having star delta connection |
| 288 | Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required. |
| 289 | 225 mm width X 50 mm depth X 1.6 mm thickness |
| 290 | 300 mm width X 50 mm depth X 1.6 mm thickness |
| 291 | Supplying, installation, testing, and commissioning of horizontal, centrifugal self-Priming watering pump, single-phase AC supply of 0.5 HP, having suction x delivery sizes of 25 mm x 25 mm and head range of 1000 LPH discharged at 10 metres head, along with float valve & Float Switch, complete with nut bolts, etc., complete as required. (Make- Crompton/ Kirloskar/ Mather Platt/ Grundfos/ Beacon/Texmo/ Lubi/KSB/CRI) |
| 292 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. |
| 293 | 20 mm |
| 294 | 25 mm |
| 295 | Dismantling the Undermentioned size of Sluice valve from the site ,servicing i/c descaling the rusted componenets , cleaning & washing with acid , replacing defective parts like Spindle Rod & T-nut including shaping ,machining , threading work ,replacing the rubber components ,gland & packing , assembling & re-installing at same location with testing etc complete as required, including credit for old scrap material which will be retained by the contractor at site |
| 296 | 100 mm to 200 mm Dia |
| 297 | 250 mm to 300 mm Dia |
| 298 | Supplying, fixing, testing & commissioning of flanged foot valve of rating PN 0.2 with cast iron body , Hing pin ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 1538 of following sizes as required (Make -Kirloskar/Karan/Zoloto/Leader/Sant) |
| 299 | 80 mm size |
| 300 | 100 mm size |
| 301 | 150 mm size |
| 302 | Supplying & fixing Nylon rope 16 mm dia complete with shackles for fixing of pump set during the lowering of pumpset to avoid slippage complete as reqd ( ISI marked as required ) . |
| 303 | Supplying and fixing of under mentioned type Cable PVC Insulated & PVC Sheathed copper conductor multi strand, 1100 Volt, conforming to IS 694 etc as reqd including credit for old scrap material which will be retained by the contractor at site (Make- POLYCAB/ HAVELLS/RR Kable /FINOLEX) |
| 304 | 3C x 2.5 Sqmm flat Submersible cable |
| 305 | 3Cx4.0 Sqmm flat submersible cable |
| 306 | 3C x 10.0 Sqmm flat submersiblecable |
| 307 | 3C x 16.0 Sqmm flat submersiblecable |
| 308 | P/F of DOL starter on the existing panel/wall(as per direction of Engg in charge) suitable upto 7.5 HP single phase submersible / open well motor pump model MK1 Make L&T or equivalent BCH/Siemens/Havells including making incoming and outgoing connections with suitable size of thimbles testing etc as required including credit for old scrap material which will be retained by the contractor at site |
| 309 | Providing and fixing starter on the existing panel/wall (as per direction of Engg in charge) suitable upto 7.5 HP three phase submersible/openwell motor including making incoming and outgoing connections with suitable size of thimbles i/c testing as required i/c credit for old scrap material which will be retained by the contractor at site.Make- BCH; Model-CPEYSAKZ with relay range 8.9-13.5A |
| 310 | P/F Fully automatic star delta starter suitable for three phase induction motor 12.5 HP to 35 HP operating 415V, 50Hz of Cat No ML2FASD(Heavy Duty) Make L&T or equivalent BCH/Siemens/Havells including making incoming and outgoing connections with suitable size of thimbles testing etc as required including credit for old scrap material which will be retained by the contractor at site |
| 311 | Providing and lowering GI pipes class B marked with IS: 1239 in 6 m length, including welding with flanges on plain ended pipe (Heavy Duty) on both sides, jointing with nuts and bolts, rubber gaskets, into Tube wells and testing commissioing etc. complete in all respects to the satisfaction of Engineer-in- Charge. (Make : ISI marked B class Jindal Hisar / Tata / Prakash Surya / Swastik / Zenith maked G.I. pipe) |
| 312 | 32mm Dia |
| 313 | 40mm Dia |
| 314 | 50mm Dia |
| 315 | 65mm Dia |
| 316 | Providing & fixing the undermentioned GI assecories as per direction of engineer in charge including credit the old dismantle etc |
| 317 | Heavy duty 50mm MS flange |
| 318 | Suitable length Reducer 65-50 /50-65mm |
| 319 | Bend/Elbow threaded GI 50 mm dia |
| 320 | Union GI 50 dia |
| 321 | Nipple GI dia 50 mm ( up 10 inch) |
| 322 | Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required |
| 323 | 2 X 25 sq. mm (22mm) |
| 324 | 3½ X 35 sq. mm (32mm) |
| 325 | 3½ X 50 sq. mm (35mm) |
| 326 | 3½ X 70 sq. mm (38mm) |
| 327 | SITC Pressure Gauge mild steel bottom connection min range 0-10 Kg/cmsq including connection pipe and assecories complete in all respect (Make - H.Guru/FieBig) |
| 328 | SITC Pressure Guage range 0-14 Kg/cmsq glycerine filled including connection pipe and assecories complete in all respect (Make - H.Guru/FieBig) |
| 329 | Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclo sure with cover plate having locking arrangement and wa tering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required. |
| 330 | Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required. |
| 331 | Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required. |
| 332 | Providing & Fixing 25mmx5mm GI strip on surface or in reccess for connections etc. as required. |
| 333 | Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required. |
| 334 | Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required. |
| 335 | Providing and fixing 3 Phase auto, manual, By pass mode single device for Protection against Single Phasing, Phase Reversal, Dry Run with adjustable settings, Current unbalance. in existing cubicle panel/starter board including drilling holes in cubicle panel, making connections, etc. as required including credit for old scrap material which will be retained by the contractor etc., complete as required. |
| 336 | Providing and fixing following switch gears, meters and accessories in existing cubicle panel/starter board including drilling holes in cubicle panel, making connections, etc. as required including credit for old scrap material which will be retained by the contractor etc., complete as required. |
| 337 | 3Pole,415V , Power contactor AC3 rating 18 A |
| 338 | 3Pole,415V , Power contactor AC3 rating 25A |
| 339 | 3Pole,415V , Power contactor AC3 rating 40A |
| 340 | 3Pole,415V , Power contactor AC3 rating 80A |
| 341 | ML4W type Contactor |
| 342 | MK1 type Contactor |
| 343 | MU1 type Contactor |
| 344 | ML2W type Contactor |
| 345 | TPN 40/63A |
| 346 | Lamp Indicator ( R/Y) |
| 347 | Lamp Indicator ( B) |
| 348 | Overload thermal relay MK1 13-22 A |
| 349 | Overload thermal relay MU1 |
| 350 | 3Ph LED Ammeter Cl 1 |
| 351 | 3Ph LED Voltmeter Cl 1 |
| 352 | Add on Block 1NO+1NC |
| 353 | Add on Block 2NO+2NC/ 3 NO+ 1 NC/ 1 NO + 3 NC |
| 354 | Single phase preventor SPPR SDz5 |
| 355 | Supplying and laying of one number PVC/XLPE insulated and PVC sheathed/XLPE aluminium armoured conductor power cable 1.1 KV grade of following size in the existing RCC/ HUME/ STONEWARE/ METAL/ DWC pipe as required. |
| 356 | 2 X 25 Sq.mm |
| 357 | 3.5 x 50Sqmm |
| 358 | 3.5 x 70Sqmm |
| 359 | Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required |
| 360 | 50 mm dia |
| 361 | 100 mm dia |
| 362 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. |
| 363 | Excavation for cable trenches in soft soil, depth upto 1.2 m including dressing of sides lift upto 1.5 m, including getting out the excavated soil, refilling with sand and or good soil after laying of cable/ pipe etc in layers of 20 cm, ramming, watering and disposal of surplus excavated soil as directed, within a lead of 50 metres. |
| 364 | Deduct for not consolidation by ramming and watering while re-filling with sand and or good soil in cable/ pipe laying. |
| 365 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. |
| 366 | 63 mm dia (OD-63 mm & ID-51 mm nominal) |
| 367 | 120 mm dia (OD-120 mm & ID-103 mm nominal) |
| 368 | Providing and installing a heavy-duty 3-inch weld on Barrel metal Hinge on the doors of existing Indoor/Outdoor LT-panel/Feeder Doors by means of welding and painting the entire weld-affected surface with 2 or more coats of synthetic enamel paint after 1 coat of red oxide to match the finishing of the weld-affected area to the adjacent surface, etc., as required. |
| 369 | Providing and fixing universal type SS door lock mechanism for existing Indoor/Outdoor LT-panel/Feeder Doors including making holes, ensuring its tight placement without any free-play by way of suitable rubber/solvent seals etc as required |
| 370 | Providing & fixing 3 mm thick CRCA gland plate of required size, duly treated and painted, in existing indoor/outdoor LT panel/feeder/Junction feeder box and making necessary holes in the gland plate for management of the existing cables in the panel/feeder, including taking out the existing gland, lugs, cables and re-fixing etc., as required. [Lugs/Thimbles or glands, if required, will be paid separately] |
| 371 | Fabrications, supplying and fixing of covers of the required shape and size in the existing electrical cubical panel boards/distribution boards/ feeder pillars /pole box at different locations made out from 2 mm thick CRCA sheet with locking arrangement, hinges and matching with the existing doors of the panel including painting with an approved shade of two coats of synthetic enamel paint over an undercoat of steel primer etc., complete as required. |
| 372 | Welding by gas or electric plant including transportation of plant at site etc. complete. |
| 373 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :(Note:- For Panel & Metallic Plate. Complete with scrapping as required) |
| 374 | One or more coats on old work |
| 375 | Providing & fixing 18mm thick water resistant plywood of size 300 x 300 mm (nominal) on wall with anchor fastener etc. complete as required |
| 376 | Providing, installation, testing and commissioning of Ball valve of following sizes confirming to IS: 554/ BS 21/ ISO 7/IS 1318/ for different parts each complete with rubber gasket, Gl bolts, nuts, washers, Stainless Steel ball etc.as required: |
| 377 | 50 mm dia |
| 378 | 65 mm dia |
| 379 | Providing, installation, testing and commissioning of Bronze Ball valve (Screwed) of 25mm size etc.as required including dismenling of existing damaged valve. Make-Zoloto; Art No. 1008 B |
| 380 | Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, Gl bolts, nuts, washers etc.as required: |
| 381 | 80 mm dia |
| 382 | 100 mm dia |
| 383 | 150 mm dia |
| 384 | 200 mm dia |
| 385 | Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required: |
| 386 | 50mm dia |
| 387 | 65 mm dia |
| 388 | 80 mm dia |
| 389 | 100 mm dia |
| 390 | 150 mm dia |
| 391 | 200 mm dia |
| 392 | 300 mm dia |
| 393 | Rewiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable and 1.5 sq.mm FRLS PVC insulated copper conductor single core cable as earth wire in existing surface/ recessed steel/PVC conduit including dismantling as required. |
| 394 | Group A |
| 395 | Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required. |
| 396 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required. |
| 397 | 3 X 1.5 Sq.mm |
| 398 | 3 x4 Sq.mm |
| 399 | 6 x4 Sq.mm |
| 400 | 3 X 6 Sq.mm |
| 401 | Providing and lowering GI Tail piece class B Nipple weld on Pump i/c \\"B\\" Class GI Pipe Nipple of 32-40mm dia dia of one end threadedand one end plainmarked with IS: 1239 in 0.5 m length, including threading and welding with flanges (Heavy Duty) on single side, jointing with nuts and bolts, rubber gaskets, into Tube wells and testing commissioing etc. complete in all respects to the satisfaction of Engineer-in- Charge. (Make : ISI marked B class Jindal Hisar / Tata / Prakash Surya / Swastik / Zenith maked G.I. pipe) |
| 402 | Providing and lowering GI Bend with flange piece class B marked with IS: 1239 , including threading and welding with flanges (Heavy Duty) on single side, jointing with nuts and bolts, rubber gaskets, into Tube wells and testing commissioing etc. complete in all respects to the satisfaction of Engineer-in- Charge. (Make : ISI marked B class Jindal Hisar / Tata / Prakash Surya / Swastik / Zenith maked G.I. pipe)50mm Dia |
| 403 | Providing and fixing M S Bore Cap of size 8\\"x2\\" at the top of the Bore jointing with nuts and bolts, rubber gaskets, into Tube wells and testing commissioing etc. complete in all respects to the satisfaction of Engineer-in- Charge. |
| 404 | Providing and fixing M.S. clamp of required dia to the top of pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. |
| 405 | Supplying & Fixing of Single Door Box, of size (Size (WxHxD) mm600x400x300IP - 55 Box, Made out of 1.6 mm CRCA sheet steel, Foamed-in PU gasket, cable Gland Plate of 2mm Thickness, Foamed in PU gasket on existing, Mounting Plate of thickness 2.0 mm Galvanised Steel on existing Foundation angle. |
| 406 | Supplying & Fixing of Single Door Box, of size (Size (WxHxD) mm600x600x300 IP - 55 Box, Made out of 1.6 mm CRCA sheet steel, Foamed-in PU gasket, cable Gland Plate of 2mm Thickness, Foamed in PU gasket on existing, Mounting Plate of thickness 2.0 mm Galvanised Steel on existing Foundation angle. |
| 407 | Providing and fixing Din-rail 35 mm x 7.5 mm on exisitng panel etc., as required. i) Din-rail 35 mm x 7.5 mm |
| 408 | Supplying and fixing a PVC cable gland suitable for up to 6 sq mm of copper conductor cable in the existing polycarbonate cable junction box, including connections, etc. as required. |
| 409 | Providing of following chemicals fit as per direction of engineer in charge :- |
| 410 | NAOCL in Jerry Can20/40L as per relevent IS code |
| 411 | Dia Ammonium phosphate Brand Sardar or equivalent |
| 412 | Industrial Grade UREA(Granular and Crystal) having 46%Nitrogen Purity Content |
| 413 | Cubes Natural Industrial Jaggery For ETP/STP |
| 414 | Natural Grade Microbial Bioculture for STP Plants (Package of 5Ltr Each) Make - ACUROBAC S50 or Equivalent |
| 415 | Replacement of the following spare parts of the existing water supply sluice valve sizing 250mm to 300mm with a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required |
| 416 | New Spindle including machining & threading etc |
| 417 | T-Nut including shaping & threading etc |
| 418 | Replacement of the following spare parts of the existing 01 MLD STP with a new one if found defective, including testing, complete as required, including credit for old scrap material which will be retained by the contractor etc., complete as required. |
| 419 | PVC dosing Pipe Size 6mm Dia |
| 420 | Non clog type fine bubble air diffuser complete set memrane with pipe 63x1000mm with end connection 3/4'' SS304 (20mm) thread type capable of air handling 7.5-10 cum per hour (size ) |
| 421 | Filling Press Hydraulic Oil (Grade No68)Servo |
| 422 | Filter Cloth Size |
| 423 | Upvc Pipe Size 25mm |
| 424 | Upvc T size 25mm |
| 425 | upvc Elbow 25mm |
| 426 | Coarse Air Bubble Diffuser round shape MOC -EPDM end size 25mm |
| 427 | Screw Pump BD1080A Belt set |
| 428 | Filter press PPMwater tap |
| 429 | Providing and fixing C.I Cover for Borewell of assortes size as required incuding Nut-bolt . |
| 430 | Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 431 | Providing pump weld on GI Nipple with the help of MS Strip and making hole of suitable diameter at other end of strip and fixing this strip on pump with the help of nut bolt etc as required. |
| 432 | Providing and fixing Magnet coil of 360 Volt and accessories in existing cubicle panel/starter board including drilling holes in cubicle panel, making connections, etc. as required including credit for old scrap material which will be retained by the contractor etc., complete as required. Make- L&T |
| 433 | Providing and lowering GI Tail piece class B Nipple weld on Pump i/c \\"B\\" Class GI Pipe Nipple of 50 - 65mm dia of one end threadedand one end plainmarked with IS: 1239 in 0.5 m length, including threading and welding with flanges (Heavy Duty) on single side, jointing with nuts and bolts, rubber gaskets, into Tube wells and testing commissioing etc. complete in all respects to the satisfaction of Engineer-in- Charge. (Make : ISI marked B class Jindal Hisar / Tata / Prakash Surya / Swastik / Zenith maked G.I. pipe) |
| 434 | Dismentling of old non repairable Sluice valve/Non return valve/Butterfly valve/Foot valve from the site i/c cutting of all rusted/damaged nut- bolts with the help of cutting tool etc as required. |
| 435 | Testing of Water |
| 436 | Testing of Natural Drinking water Test Complete Parameters:-Colour, Order, pH Value @ 27°C, Taste, Turbidity, Total dissolved solids, Aluminium (as Al), Ammonia (as total ammonia-N), Anionic detergents (as MBAS), Boron (as B), Calcium (as Ca), Chloramines (as Cl2), Chloride (as Cl), Fluoride (as F), Free residual chlorine, Iron (as Fe), Magnesium (as Mg), Manganese (as Mn), Nitrate (as NO3), Phenolic compounds (as C6H5OH), Sulphate (as SO4), Total alkalinity, Total hardness, Zinc (as Zn), Cadmium, Lead, Molybdenum, Nickel, Total chromium, Copper, Sodium (as Na), Conductivity complete etc. as required. |
| 437 | Testing of R.O Water/ Drinking Water Test/borewell , with following minerals presence and their Parameters.Parameters are following:- Mercury, Cadmium, Selenium, Arsenic, Lead, Zinc, Chromium, Alkalinity, Aluminium, Boron, complete etc. as required. |
| 438 | Testing of STP inlet & outlet Water Test, Parameters are:-pH, TSS, BOD, COD, Oil & Grease, Phosphorous, Total Nitrogen complete etc. as required. |
| 439 | Credit for old unserviceable Item like Suice valve ,NRV ,MS pipe ,flange etc i/c dismantle from the site & weighing in presence of deptt representative as required . |
| 440 | Credit for old unserviceable Item like copper from motors etc i/c dismantle & weighing in presence of deptt representative as required . |
| 441 | Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by \\"V\\" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. |
| 442 | Providing services of a suitable hydraulic crane with a capacity of 10 to 12 MT for material handling, shifting, and lifting of Booster Pump Sets, and other heavy machinery as and when required, including all lubricants, spare parts, consumables, fuel (Diesel), operator, maintenance staff, etc. as required |
| 443 | SITC 50 mm Woltman Type Cast Iron Water Flow Meter both side flange including connection pipe and assecories complete in all respect (Make - H.Guru/FieBig) |
| 444 | Flow meter 50mm |
| 445 | Flow meter 65mm Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
CompletedOct 22, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
CompletedTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender