Tender For Repair To Fencing, Compound Wall Hard Standing, Drain & Other Allied Works In Otm Accn- I, Ii, Iii, Iv & V And Other Areas Of Age B/R-I Under Ge (North) Ambala Cantt
Tender Value
60 Lakhs
Estimated cost
Bid Submission
05 Nov 2026
21 days left
EMD
1.15 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Ambala → Haryana
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair To Fencing, Compound Wall Hard Standing, Drain & Other Allied Works In Otm Accn- I, Ii, Iii, Iv & V And Other Areas Of Age B/R-I Under Ge (North) Ambala Cantt
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) including removal the rubbish/ demolished material outside defence land,complete all as specified and directed. |
| 2 | Material and labour for machine pressed rubber moulded coloured precast concrete interlocking paver block, any shape and size conforming to IS 15658–2006 of 60 mm thickness, grade M–30 with grey cement and pigments over and including a layer of sand cushioning, 25 mm thick complete all as specified and as directed. |
| 3 | Material and labour for machine pressed rubber moulded precast coloured concrete interlocking paver block, any shape and size conforming to IS 15658–2006 of 80 mm thickness, grade M–35 with grey cement and pigments over and including a layer of sand cushioning, 25 mm thick complete all as specified and as directed. |
| 4 | Supply and fixing as in repair precast cement concrete louvres and jallies, 25mm thick type B0 1:2:4 (12.5 mm graded aggregade) measured solid, including all mouldings Set in cement mortar 1:4, complete all as specified and as directed. |
| 5 | Supply and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage complete all as specified and as directed. |
| 6 | Material and labour for providing PCC (1:4:8) Type D2 using 40mm graded crushed stone aggregate as in foundations, filling and mass concrete, complete all as specified and as directed. |
| 7 | Excavating in trenches, not exc 1.5m wide and not exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exc 10 sq. m on plan and not exc 1.5m in depth and getting out in soft/loose soil, complete all as specified and as directed. |
| 8 | Removing excavated soils n exc. 50m and depositing where directed at a level n exc. 1.5m above the starting point complete all as specified and as directed. |
| 9 | Returning filling in including spreading levlling ,watering and well ramming in layers nexc 25cm thick complete all as specified and as directed. |
| 10 | Material and labour for plain cement concrete 1:3:6, type C-1 (using 20mm graded mechanically crushed stone aggregate), as in surface channels and drains complete, all as specified and as directed. |
| 11 | Material and labour for 25 mm thick PCC 1:2:4, type B–0 as in sub base floor (using 12.50mm graded crushed stone aggregate), finished even & fair without using extra cement complete, all as specified and as directed. |
| 12 | Material and labour for 8-10mm thick heavy duty (Digital) vitrified tiles of size 300 x 300mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar (1:4), complete all as specified and as directed. |
| 13 | Material and labour for 10mm thick full body vitrified coloured tiles of size 600 x 600mm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in cement mortar (1:4) , complete all as specified and as directed. |
| 14 | Dismantling dilapated /decayed posts or struts (wood, steel or R.C.C.) of any section /height, including taking out embedded portion, embedded in concrete /brick work /masonry /natural ground and each n exc 0.5 cum in volume below GL, getting out and removing surplus soil to a distance n exc 50 m and making good complete all as specified and as directed. |
| 15 | Dismantling of wire mesh fencing of any type/size and in any position, neatly coiled and removing from site complete, all as specified and as directed. |
| 16 | Excavating in post holes (or similar holes) each not exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance not exc 50m and making good surface, work in soft/loose soil, complete all as specified and as directed. |
| 17 | Material and labour for plain cement concrete 1:3:6, type C-2 (using 40mm graded mechanically crushed stone aggregate) as in foundations, filling and mass concrete complete, all as specified and as directed. |
| 18 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provision of binding wire complete, all as specified and as directed. |
| 19 | Supply only chain link fencing including line wires, any mesh size and type to any type of standards, complete, all as specified and as directed. Note :-Weight of chain link fencing shall be ascertained by BOO as ordered by GE. |
| 20 | Supply & Fixing for mild steel section of any type or size as in posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe–290 Gde E–165 complete all as specified and as directed. |
| 21 | Supply and fixing, as in repair, galvanized, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanized mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured), complete, all as specified and as directed. |
| 22 | Material and labour for mild steel round bars 10mm dia and over ,cut to length, bent to shape, hooking ends for chain link fencing, complete all as specified and as directed. |
| 23 | Supply and fixing for mild steel screw bolts (machine made) of 10 mm dia, with hexagonal or square heads at one end and screwed the other and screwed end to be fitted with round washers and one hexagonal or square nut, length of bolt not exc 5 cm long complete, all as specified and as directed. |
| 24 | Dismantling wrought iron or mild steel work of any description not otherwise provided for including gates , plates , fillets, grills, stiffener for securing chain link fencing including nuts, bolts, etc. complete, all as specified and as directed. |
| 25 | Material and labour for mild steel framed work as in framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks, MS gates and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 26 | Material and labour for 16 to 18 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick rendering in cemet mortar (1:4), as in repair complete, all as specified and as directed. |
| 27 | Demolition of brick work built in cement mortar or cement lime mortar and arches pillar etc but excluding ashlar fasing dressed stone work and pre cast concret articles complete, all as specified and as directed. |
| 28 | Material & Labour for brick work with sub class 'B' bricks in straight or curved on plan exc 6m mean radius, built in cement mortar 1:6, of any description, complete all as specified and directed. |
| 29 | Material & Labour brick work with sub class 'B' old size bricks using old servicable bricks including cleaning of old bricks straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6, complete all as specified and as directed. |
| 30 | Taking down existing cement plaster up to any height including racking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed. |
| 31 | Material and labour for rough cast plaster complete as specified in SSR Part-I, clause 14.22 shall consisting of following:- firstly apply under coat in cement mortar (1:4) not less than 10 mm thick and while still it is in plastic state the rough cast mixture consisting of crushed stone or fine stone aggregate of size between 6 to 12 mm as per the texture required mixed with coarse sand and cement in the ratio (1:1:1) shall be applied, complete, all as specified and as directed. |
| 32 | Material and labour for rendering 15 mm thick up to any height on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished fair and even without using extra cement complete all as specified and as directed. |
| 33 | Prepation of new surfaces of steel any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 34 | Prepation of new surfaces of steel any description n. exc 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 35 | Material and labour for preparation of new surfaces of walls and applying two coats of cement based paint over a coat of primer up to any height complete all as specified and as directed. |
| 36 | Material and labour for preparation of old sufaces of walls and applying one coat of cement based paint up to any height complete complete all as specified and as directed. |
| 37 | Material and labour for machine cut kota stone slab 18 to 22 mm thick of size not less than 550mm x 550mm in floor, set and jointed in neat cement slurry with grey cement mixed with pigment to match the shade of the slab including rubbing and polishing (granite finish) over and including 15 mm thick screed bed in CM 1:4 complete, all as specified and as directed. |
| 38 | Material and labour for machine cut kota stone slab 18 to 22 mm thick ( kota stone shall be cut from size not less than 550mm x 550mm) in skirting , set and jointed in neat cement slurry with grey cement mixed with pigment to match the shade of the slab including rubbing and polishing (granite finish) over and including 10 mm thick rendering in CM 1:4 complete, all as specified and as directed. |
| 39 | Supply and fixing for 150mm dia of bore hole reinforced cement concrete pipes, class NP2, laid and jointed complete with collars complete all as specified and as directed. |
| 40 | Material and labour for cement concrete bed 1:4:8 type D2 to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and as directed. |
| 41 | Supply and fixing as in repair for 24 mm thick and 595mm high plain colour solid WPC jalli over brickwork complete,all as specified and as directed. |
| 42 | Material and labour for Pre cast Reinforced cement concrete using cement concrete Type B-0, 1:2:4 (12.50mm graded crushed stone aggregate) as in pre cast lintles/bands upto 1.5m clear span, parapets and railings upto 60 cm in height, copings, and the like including providing 30 x 30mm size groove on one side of lintle for securing pre cast WPC jalli all as specified and as directed. |
| 43 | Material and labour for TMT steel bars 10mm dia and over up cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia, complete, all as specified and as directed. |
| 44 | Material and labour for TMT steel bars 5mm dia and over up to and including 10mm dia in stirrups, spacers etc, cut to length, bent to shape reqd incl cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire annealed not less than 0.9mm dia, Charge. complete, all as specified and as directed. |
| 45 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specified and as directed. |
| 46 | Material and labour for providing and fixing stainless steel (Grade 304) as in railing/ grills/ ladders etc made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement, complete, all as specified and as directed. |
| 47 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete, all as specified and as directed. |
| 48 | Material and labour for providing, reinforced cement concrete M-20 (Nominal Mix) using 20mm graded crushed stone aggregate in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates water troughs and the like including weathering, slightly rounded or chamfered angles and throating rounded or chamfered on edges, complete, all as specified and as directed. |
| 49 | Demolition reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut to facilitate demolition), complete, all as specified and as directed. |
| 50 | Material and labour for brick work with sub class 'B' old size bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4, also in foul condition drain work complete all as specified and as directed. |
| 51 | Material and labour for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, mould, mitred/ stopped end etc complete all as specified and as directed. |
| 52 | Dismantling structural steel work including doors, gates, but excluding framed trusses etc complete all as specified and as directed. |
| 53 | Material and labour for rolled mild steel framed work as in door or gates (ornamental and intricate design of door) of angle or other section with gusset plates, rails, braces etc. complete drilled for fixing of steel sheeting or other covering, doors, etc to be prepared for hanging or sliding with and including either hooks and hinges and steel hanging door fitting (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing conforming to Fe–410 (Gde E–250) quality 'A' complete all as specified and as directed. |
| 54 | Material and labour for RCC (Nominal Mix) Type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) as in foundation, footing, foundation beams plinth beams and mass concrete including necessary formwork /scaffolding if reqd complete all as specified and directed. |
| 55 | Material and labour for RCC (Nominal Mix) Type B-1, 1:2:4 (using 20mm graded crushed stone aggregate) as in column, pillars, piers, posts and struts including necessary formwork /scaffolding if reqd complete all as specified and directed. |
| 56 | Demolition of Stone slabs and tiles laid bedded and pointed in any mortar of any description or thickness in floors, aprons etc. complete all as specified and as directed. |
| 57 | Demolition and breaking up drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar of 150mm dia complete all as specified and as directed. |
| 58 | Note:- Amount of credit of Rs. 1,09,195.00 for retrieved materials is mentioned in Schedule of Credit Page No. 17 of tender documents in pdf form which will be deducted offline while acceptance of tender. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 05, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysNov 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 23 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender