Tender For Improvement Of Ig Office In Adm Block At Ftr Hq Bsf Salbagan.
Tender Value
4.99 Lakhs
Estimated cost
Bid Submission
15 Oct 2026
4 days left
EMD
9991
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
tripura → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Improvement Of Ig Office In Adm Block At Ftr Hq Bsf Salbagan.
BOQ
| Sl. No. | Item Description |
| 1 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6(1 cement : 6 coarse sand) |
| 2 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 3 | Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, difusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) :2011 (Board with BIS certification marks) |
| 4 | 12 mm cement plaster of mix: 1:6(1 cement: 6 fine sand) |
| 5 | Varnishing with varnish of approved brand and manufacture: Two or more coats of glue sizing with copal varnish over an under coat of flatting varnish |
| 6 | French spirit polishing : Two or more coats on new works including a coat of wood filler |
| 7 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 8 | Dismantling cement asbestos or other hard board ceiling or partition walls including stacking of serviceable materials and disposal of unserviceable materials within 50 metres lead. |
| 9 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer- in-charge. |
| 10 | Correction factor on existing items of the DSR -2023 on account of GST @ 0.973 on item Sr No (01 to 09) |
| 11 | Add Cost Index @61% on SR&DR on item Sr No (01 to 09) |
| 12 | Providing and fixing 19mm thick factory pressed BWP grade marine ply as per IS 710 of approved brand with suitable full threaded steel screws etc. in partitions, boxes, shelves, racks and cupboard, kitchen cabinet under kitchen counter etc. all complete as per direction of Engineer-in-charge (Note: Fittings to be paid separately). 19 mm thick BWP grade marine ply conforming to IS : 710 BWR type |
| 13 | Providing and fixing non-woven textile customized wallpaper of approved manufacture, color, and pattern, manufactured from breathable, PVC-free, over a perfectly prepared, flat, leveled plaster/gypsum board surface; surface preparation to include fine sanding, application of a uniform coat of specialized primer/sealer; fixing wallpaper by applying premium heavy-duty adhesive smoothly on the wall (Paste-the-Wall technique) to prevent shrinkage at joints; ensuring zero gaps or overlaps at vertical drops; complete with all lead, lift, scaffolding up to all floor levels, disposal of trimmings, tools, and incidentals, completed in all respects as per manufacturer's specifications and instructions of the Engineer-in-Charge. |
| 14 | Providing and fixing 4 mm thick decorative Teak wood veneer of approved quality, make, shade, and grain pattern over existing wooden or plywood surfaces; including thorough cleaning and smoothening of the base surface with sandpaper to remove any irregularities; fixing the veneer sheets seamlessly using premium quality, water-resistant synthetic resin adhesive (conforming to IS: 4857 or approved equivalent); pressing and holding with appropriate clamps/masking tapes to eliminate all air bubbles, warps, or gaps; alignment of matching grains and and preparation of the finished veneer surface for polishing; inclusive of all materials, labor, tools, scaffolding, wastage, and overheads at all heights and levels, completed in all respects as per the direction of the Engineer-in-Charge. |
| 15 | Providing and fixing brass sliding door bolts, ISI marked e, with nuts and screws etc. complete : 250x16 mm |
| 16 | Providing and fixing brass coated aluminium tower bolts, ISI marked, (brass coating not less than grade AC 10 as per IS : 1868 ) , with necessary screws etc. complete : 300x12 mm |
| 17 | Providing and fixing brass coated aluminium handles, ISI marked, (brass coating not less than grade AC 10 as per IS : 1868) , with necessary screws etc. complete : 150 mm |
| 18 | Providing and fixing brass coated aluminium hanging floor door stopper, ISI marked, (brass coating not less than grade AC 10 as per IS : 1868) , with necessary screws etc. complete. Single rubber stopper |
| 19 | Providing and fixing of Verticle roller blinds madeup with 100% polyster/Fibre yarn coated with fade resistant polymer to ensure complete opaquety with zero light transmittance, having suitable coating on exterior including all fixtures and fitiings complete in all respect matching with site conditions to cover the opening as per design and instructions of Engineer-in-charge. (only opening area of windows will be measured for payment). |
| 20 | Fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like difusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coeficient) of 0.79 (All items will be provided departmentally.) Only labour charges will be paid Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 15, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysOct 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender