Tender For Special Repair Works Under Age B&R-Ii And Age Em-Iv Of Ge(S) Bathinda At Bathinda Mil Stn (Job No. Sr(B)- 35 Of 2026-27 And Sr(B)- 27 Of 2026-27)
Tender Value
49.66 Lakhs
Estimated cost
Bid Submission
29 Oct 2026
11 days left
EMD
99320
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bathinda → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair Works Under Age B&R-Ii And Age Em-Iv Of Ge(S) Bathinda At Bathinda Mil Stn (Job No. Sr(B)- 35 Of 2026-27 And Sr(B)- 27 Of 2026-27)
BOQ
| Sl. No. | Item Description |
| 1 | S&F Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing lining board, etc complete all as specified and as directed. |
| 2 | M & L for virified ceramic tile light shade 7-8mm thick double charged/ultra charged (square/rectangular) polished, area of each tiles exceeding 0.42 sqm but not exceeding 1.00sqm, in floor etc,. Set and jointed in neet cement slurry and pointed in white or coloured cement to match complete all as specified and directed. |
| 3 | Dismantling floor, hearth of wall tilling including cement mortar bedding (but not backing) removing serviceable tiles to stores and rubbish off the premises complete all as specified and directed. |
| 4 | M & L for providing screed bed or bedding layer of CM 1:6 of 15mm thick for laying floor finishes complete all as specified and as direcetd. |
| 5 | Taking down cement or cement lime plaster of any description on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specied and directed. |
| 6 | M & L for 10mm thick rendering with ready Mix Mortar on fair faces of brick work or concrete surfaces and finishing even & smooth but without using extra cement complete all as specied and directed. |
| 7 | M& L for 15mm thick rendering with ready Mix Mortar on other than fair faces of brick work or concrete surfaces and finishing even & smooth but without using extra cement complete all as specied and directed. |
| 8 | Preparation of New/Old external wall surface complete all as specified complete all as specified and applying the following:-(a) M&L wall care putty a coat of 1.5mm thick layer on wall surface and smoothening the surface with sand papers / Mechanised sanding etc prepatory to paint as directed complete all as specified.(b) two coat of acylic emulsion distemper over a coat of chalk whitening priming by using Airless spray/Roller complete all as specied and directed.Note:- Contractor may use manual scraping tools for complete removal and surface preparation with prior approval or Engr-in-charge in case of using of Mechanical equipment are not possible. |
| 9 | M&L for preparation of surfaces by mechanized sander having suction vacuum bag using smart periodical methodology complete all as specified. Providing and applying of paris putty of 1.5mm thickness over plastered surface to prepare the surface even and smooth and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and directed.Note : Before applying painting (OBD & Exterior emulsion) in in bldgs a sample patch of size 1 mtr x 1 mtr to be done for approval of GE. Painting should be done by using painting roller, mechanically method and as per manufacturer's instructions. Cost for the same for scaffolding for plastering & painting etc is included in the rates quoted by the contractor. |
| 10 | M & L for preparation of old surfaces on ceilings and applying one coat of white wash complete all as specified and as directed. |
| 11 | Material and Labour Green Marble work 18 to 20mm thick (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed. |
| 12 | S & F anodized aluminium snap grid frame work for false ceiling grid 605mm x 605mm etc complete all as specified and directed |
| 13 | S & F Hangers 6mm dia G.I.(upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3mm size 60mm long and expansive hold fasteners 12.5mm dia 40mm long complete all as specified and directed |
| 14 | M&L for 10 mm thick non asbestos fiber cement building boards fixed or laid/inserted to timber/GI/aluminium frame work with screws fixed in ceiling flat or sloping complete all as specified and directed. |
| 15 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (fixed portion) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS : 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gap at junctions, ie at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/paneling, CP brass/stainless steel screws, all complete as per architechural drawings and directions |
| 16 | M & L for powder coated (minimum thickness of powder coating 50 micron) aluminium door shutters, aluminium section weighing 0.55kg/m including joining cleats, glazing clips, ruber neoprene packing, handles 3 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified and directed. |
| 17 | M & L for powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator shutters, fixed/sliding type without sash bar, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, anodised aluminium snap beading, sliding roller, screws etc. complete all as specified and directed. |
| 18 | S & F for 5 mm thick, tinted/pin head type glass and glazing with UPVC bends/ neoprane packing and other accessories in squares to window door and fixed partition complete all as specified and directed. |
| 19 | Taking down chowkhat with shutters (without taking off shutters from the frames exc. 1.5 sqm but n. exc. 4.0 sqm each complete all as specified and directed. |
| 20 | Dismantling fencing wiremesh any type complete all as specified and directed. |
| 21 | Dismantling wrought iron or mild steel work of any sdescription not otherwise provided for complete all as specified and directed. |
| 22 | S & F in repair Punched Tape concertina coil (PTCC) fencing of 450mm dia (at stretched position) made out of hot dipped, galvanised steel wire coated with CLR anti corrosive paint, making diamond shape barbs with 18 SWG sheet, spring core 2.5mm thick wire with tape 0.52mm thick and weight of each coil should not be less than 8.60kg, each coil should have 50 rounds and should covers 6 RM length fixed over and including 6 lines of horizontal RBT ( reinforced barbed tape) wire or razor wire at points wherever coil touches the bottom of wire with the help of hog rings (14 SWG) and between Y shaped abgle iron post complete all as specified and directed.Note:- (i) Hogging shall be fixed at a interval of 600mm centre, wherever in touches with the razor wire.(ii) Overlapping of concertine coil and razor wire shall be 300mm.(iii) Y- shaped angle iron posts shall be measured and paid separately under respective items. |
| 23 | S&F in repairs galvanised, 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 65mm to 75mm spacings and straining and fixing to any type of standard rails, straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc as directed (each line of wire to be measured), complete all as specified and directed. |
| 24 | S&F mild steel works as in Hand rails, half round or other steel section or core for wooden hand rail straight portion, drilled or countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts, post and struts in fencing including cutting tops to shape as directed, drilling, holes, notching for wire etc, flat iron fillets (for securing wiremesh etc) including all necessary drilling, bolting or riveting, etc, and similar work conforming to Fe-290 Gde E-165 complete all as specified and directed. |
| 25 | M&L preparation of new steel surface exceeding 10cm width or girth and applying two coats of synthetic enamel paints over one coat of red oxide primer complete all as specified and directed. |
| 26 | M&L preparation of old steel surface exceeding 10cm width or girth and applying two coats of synthetic enamel paints complete all as specified and directed. |
| 27 | Taking down carefully existing copper/Aluminum point wiring (light,fan, socket or power) complete including fixture and fittings such as switches, bellpushes, ceiling roses, pendents, regulators, sockets, light fitting, callbells etc removiing materials to store for keeping in safe custody or for taking credit(credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc. to match existing complete allas specified and directed |
| 28 | Material and labour for one light / fan point controlled by one, one way modular switch 06 Amp wiring with 1.5 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sq mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLSH copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 20mm dia in medium grade complete with and including modular metal flush boxes not less than 1.6mm thick alongwith modular cover plate with frame of any size for mounting of any type modular switches/sockets/bell switch /fan regulator and brass screws, cup washers etc complete, making good the distributed surfacess completely matched and finished with existing surfacess including painting of walls etc complete all as specified and directed. |
| 29 | All as per srl item No. 28.00 (here-in-before) but One 3 pin socket outlet 6 Amp on same board point, complete all as specified and directed |
| 30 | All as per srl item No. 28.00 (here-in-before) but One 3 pin socket outlet 6 amp on the independent board point complete all as specified and directed |
| 31 | All as per srl item No. 28 (here-in-before) but for 15/16 Amp socket out let/power point by using 4.0 Sqmm PVC insulated unsheathed copper conductor cable FR-LSH multi strand on independent board including provn of 4.0 Sqmm unsheathed, multi stranded copper conductor cable FR-LSH continues as earth wire connected to earth dolly etc complete all as specified and directed |
| 32 | S&F of Modular switch 1 way 6A/10A 1 module single pole complete all as specified and directed. |
| 33 | S&F of Modular switch 1 way 16A, 1 module single pole complete all as specified and directed. |
| 34 | S & F Modular Socket oultet 6A - 2/3 pin combined 2 module, 230 volt, multipurpose, complete all as specified. |
| 35 | S & F of Modular Socket outlet 6A/16A - 2/3 pin combined 2 module, 230 volt,multipurpose, complete all as specified. |
| 36 | S & F Modular Fan step regulator, 120W - 2 module with 5 steps type complete all as specified. |
| 37 | S & F ceiling rose surface bake lite with 3 terminals complete all as specified and directed. |
| 38 | Supply and Fixing only decorative wall light fixture made of polycarbonate suitable for retrofit 9W LED lamp(base B-22) complete with PC diffusor & including one 9W LED lamp(base B-22), 3000/6500K, not less than 90 lumen/watt efficacy including making connection complete all as specified and directed. |
| 39 | Supply and fixing replacement of SPN enclosure with a two pin and earth plug and socket complete with and including MCB, SP, AC, 240 volt of 20 Amp, 'C' curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed. |
| 40 | Supply and fixing of Inverter LED tube light fittings 1200 mm, 20 W ,6500K higher energy saving decorative ultra slim square profile LED lighting fixture with extruded aluminium housing ,enviromental friendly, energy efficient ready to use pack and comprising of batten with all accessories internally prewired and connecting up with twin core twisted copper conductor cable complete all as specified and directed. |
| 41 | Supply and fixing of LED panel light fitting, cool /warm white Surface mounted, square shaped of size 2'x2' area, 6500/3000K 36(±10%)watts efficacy not less than 90 lumen/watt, extruded Aluminium/polycarbonate, PC diffusor, module and inbuilt driver complete including making connection with and including electrical connection with 1.5 mtr long twin core round copper conductor cable of suitable size and testing complete all as specified and directed |
| 42 | Taking down old complete and Material and labour sub main wiring with 06 Sq mm nominal cross sectional area, two single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 06 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 25 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to matched and finised with existing surface are included in the ratecomplete all as specified and directed.Note:- (i) 2 run of 6.0 Sqmm main cable, one run of 6.0 Sqmm earth wire and one run length of PVC conduit of size 25mm shall be considered as one running length.(ii) The wiring shall be done in proper color coding using Red,Yellow, Blue for phases, Black for neutral and Green for earth. |
| 43 | Taking down old complete and Material and labour Three phase sub main wiring with 10 Sq mm nominal cross sectional area, four single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 10 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 32 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to matched and finised with existing surface are included in the ratecomplete all as specified and directed.Note:- (i) 4 run of 10.0 Sqmm main cable, one run of 10.0 Sqmm earth wire and one run length of PVC conduit of size 32mm shall be considered as one running length.(ii) The wiring shall be done in proper color coding using Red,Yellow, Blue for phases, Black for neutral and Green for earth. Please Enable Macros to View BoQ information |
| 44 | Taking down old complete and Material and labour Three phase sub main wiring with 10 Sq mm nominal cross sectional area, four single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable with and including continuous earth wire of size 10 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic PVC conduit of 32 mm dia, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and making good to the disturbed surfaces to matched and finised with existing surface are included in the ratecomplete all as specified and directed.Note:- (i) 4 run of 10.0 Sqmm main cable, one run of 10.0 Sqmm earth wire and one run length of PVC conduit of size 32mm shall be considered as one running length.(ii) The wiring shall be done in proper color coding using Red,Yellow, Blue for phases, Black for neutral and Green for earth. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 08, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 29, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysOct 31, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 13 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender