Tender For special Repair To Bldg No P-7A (Unit Pers Cook House And Dining Hall) Of Fd Hosp-I Under Ge (North) Binnaguri
Tender Value
38.08 Lakhs
Estimated cost
Bid Submission
31 Oct 2026
16 days left
EMD
76160
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalpaiguri → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No P-7A (Unit Pers Cook House And Dining Hall) Of Fd Hosp-I Under Ge (North) Binnaguri
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises complete all as specified and as directed. |
| 2 | M&L Vitrified Ceramic tiles light shade 9 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 sqm but n.exc 1.00 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles as in floor over and including cement screed bed / backing layer of 15mm thick in cement mortar (1:6) complete all as specified and as directed. Note:- Design and pattern shall be approved by Engr-in-charge /GE at the time of execution of work. |
| 3 | M&L non skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.18 Sqm but n. exc. 0.38 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in whiter or coloured cement to match as in floor over and including cement screed bed / backing layer of 15mm thick in cement mortar (1:6) complete all as specified and as directed.Note:- Design and pattern shall be approved by Engr-in-charge /GE at the time of execution of work. |
| 4 | M&L non skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exceeding 0.11Sqm but n. exc. 0.18 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in whiter or coloured cement to match as in floor over and including cement screed bed / backing layer of 15mm thick in cement mortar (1:6) complete all as specified and as directed.Note:- Design and pattern shall be approved by Engr-in-charge /GE at the time of execution of work. |
| 5 | M&L glazed ceramic coloured / digital printed/Elevation tiles of size 300 x 450 mm x 7 mm thick ) as in vertical surfaces of walls such as skirting /dado / riser to steps etc conforming to IS - 13712 grade IB-III set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over and including cement screed bed / backing layer of 10mm thick in cement mortar (1:4) complete all as specified and as directed. Note:- Design and pattern shall be approved by Engr-in-charge /GE at the time of execution of work. |
| 6 | Demolition of cement concrete (un-reinforced ) in ground floors and pavings n.exc 15 cm thickness (below or above ground level) complete all as specified and as directed. |
| 7 | M&L 75mm thick cement concrete (1:3:6) type C-2( using 40mm graded crushed stone aggregate) as in plinth protection laid in alternate bays (not exceeding 2 Sqm each) and finished even and smooth without using extra cement and providing joints throughout the thickness of the plinth protection filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and as directed. |
| 8 | Demolition of wall and ceiling board (Fibre,pulp,insulation etc.) or insulation board /slab/blankets any thickness including cover fillet , complete all as specified and as directed. |
| 9 | S&F Fluted PVC wall panelling to walls as indicated on approved drawings and to the satisfaction of the Engineer-in-charge. Panels shall be manufactured from high grade virgin PVC material, moisture-proof, termite-proof, fire-retardant and UV- resistant, with uniform concave/reeded vertical flute profile. Flute width,panel thickness [5mm-10mm], colour and finish shall be as per approved sample and drawings. panels shall be lightweight, dimensionally stable, and free from warps, cracks, blisters or surface defects. panels shall be fixed to a prepared wall surface or pre-fixed timber/MDF fillet batten framework using approved construction adhesive and / or concealed mechanical fasteners/clip fixing system as reccommended by the manufacturer. complete all as specified and directed by Engr-in-charge |
| 10 | S&F fillet battens to walls as a substrate framework for the installation of fluted wall panelling, as shown on approved drawings and to the satifaction of Engineer-in-charge. Fillet shall be of seasoned timber or MDF sections, free from warping, twisting, splits or defects of size[25mm x 50mm / 38mm x 50mm] or as specified, fixed horizontally and/or vertically to the wall surface at maximum [400mm/600mm] centers, or as required to suit the panel joint layout and manufacturers instructions. Fillets shall be fixed to wall using appropriate rawl plugs and screws, coach bolts or powder-actuated fasteners into masonary/concrete backgrounds, ensuring all batten are plumb, level and true to plane. complete all as specified and directed |
| 11 | Demolition of stone slab and tiles of any description or thickness as in floors, apron etc laid dry or, bedded and pointed in any mortar complete all as directed. |
| 12 | M&L machine cut Kota stone slab as in flooring, 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over & including 20 mm thick screed bed in CM 1:6 complete all as specified and as directed. |
| 13 | M&L 16-18 mm thick Granite ( Jet Black) work ( table rubbed and polished) in steps , jambs, pillars,floors, window cills, cooking plateforms and like in cement mortar ( 1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15 mm thick screeding in CM 1:4 including full rounding the exposed surfaces complete all as specified. |
| 14 | Taking down tarfelt with cement plaster from roof surfaces and lowering and removing the same from site including roughening of old concrete suirface of roof by wire brushing and cleaning the surface to remove all loose dust etc complete all as specified and as directed. |
| 15 | Material and labour for rendering 10 mm thick screed bed on roof slab concrete surfaces , in cement and sand mortar 1:4 using water liquid water proofing compound as per manufacturer's instructions complete all as specified and as directed.Note :-WPC shall be measured and paid separately. |
| 16 | M&L providing and applying single component acrylic polymer modified, fibre reinforced waterproof coating in 4 coats of application as under:- (a) applying primer coat with Primer @ 0.3 kg /sqm (b) over priming coat applying applying single component acrylic polymer modified as manufacturer instructions with fibre reinforcement a width of approx 1m @ 0.75kg/sqm on the flat or vertical surfaces over parapet wall and ensure that there are no bubbles of creases. Overlapping of the fibre is a minimum of 50mm and allow this coat to dry for a period of 2-6 hrs depending on the atmospheric condition. (c) Applying second coat of roof guard @0.75Kg/sqm (d) Applying final coat of primer @ 0.08kg/sqm after 2nd coat has dried properly. Note : Water Proofing treatment shall be carried out by authorised applicator approved by the manufacturer. . |
| 17 | Supply only Liquid water proofing compound conforming to IS: 2645 - 1975 specification complete all as specified and as directed. |
| 18 | Dismantling water tanks of any capacity of 1000 ltrs of any discription complete all as specified and as directed. |
| 19 | S & F 1000 ltrs rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) including connecting up pipes securing access covers etc as specified and as directed. |
| 20 | S&F 20 mm dia PVC ball cock (PVC float valves) complete high pressure with epoxy coated aluminum rod and high density plastic ball screwed for iron pipe and fixed as required to use reducer and check nut |
| 21 | S&F 20mm bore Gun metal globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed all complete as specified and as directed. |
| 22 | Taking up or down GI 15mm bore pipe and connection complete all as specified and as directed. |
| 23 | Taking up or down GI 20mm steel tubing and connections complete all as specified and as directed. |
| 24 | S&F 15mm bore pipe medium grade galvanised iron water tube with all fittings laid in floors fixed to wall etc complete all as specified and as directed. |
| 25 | Refixing old 15mm GI tubing and connections on new or old position (walls, ceilling, floor etc) including cleaning of pipes (Serviceable pipe obtained form iten No 22 have-in-before) complete all as specified and as directed. |
| 26 | S&F 20mm bore pipe medium grade galvanised iron water tube with all fittings laid in floors fixed to wall etc complete all as specified and as directed. |
| 27 | Refixing old 20mm GI tubing and connections on new or old position (walls, ceilling, floor etc) including cleaning of pipes (Serviceable pipe obtained form iten No 23 have-in-before) complete all as specified and as directed. |
| 28 | Taking down cement plaster on wall & ceiling of any description including racking out joints, hacking for key and scrubbing down with water etc complete all as specified and directed. |
| 29 | Demolition of brick work built in cement mortar of any description,etc complete all as specified and as directed. |
| 30 | M&L brickwork with fly ash bricks straight or curved on plan exc 6mtr mean radius built in cement mortar 1:6 complete all as specified and as directed. |
| 31 | M&L brickwork with fly ash bricks straight or curved on plan to any radius as in half brick wall built in cement mortar 1:4 complete all as specified and as directed. |
| 32 | M&L for 15 mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layers first layer of 10 mm thick and top layer of 5 mm thick plaster with water proofing compound as per manufacturer's instructions finishing the surface even & fair without using extra cement complete all as specified and as directed.(NOTE :Water Proofing Compound shall be measured and paid separately. |
| 33 | M&L 15 mm thick rendering in cement mortar 1:6 on other than fair face of brick work or concrete surface finished even & fair (without using extra cement) complete all as specified and as directed. |
| 34 | M&L for rendering 5mm thick plastering in CM (1:3) on ceiling, soffits of slabs, chajjas, columns and beams etc and finished the plastered surface even and smooth without using extra cement , complete all as specified and as directed. |
| 35 | M&L prepartion of new surfaces of wall and applying two or more coats of distempering with 1st quality acrylic distemper (ready mix) having VoC content less than 50gm/ltr of approved manufracturer of required shade and colour over a coat of primer after applying One coats of wall care putty complete all as specified and as directed. |
| 36 | M&L preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed. |
| 37 | M&L preparing newly plastered or unplastered surface of ceiling and applying three coats of white washing complete all as specified and as directed. |
| 38 | M&L preparation of newly plastered surfaces on wall / ceiling / chajjas and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 Ltre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over as per the manufacturer instruction complete all as specified and as directed. |
| 39 | M&L preparartion of old surfaces applying of distempering with 1st quality acrylic distemper (ready mix) having VoC content less than 50gm/ltr of approved manufracturer of required shade and colour complete all as specified and as directed. |
| 40 | M&L preparation of old treated surface of wall by brooming down or steel wire brushing; scrapping down smoke root, moulds, moss and efflorescent salts and treating oil and greasy spots and applying two coat of white wash on old decorated surfaces of wall including washing froors, cleaning glass, joinery, electrical fittings, wiring etc of drops and splashes complete all as specified and directed. |
| 41 | M&L complete removal of existing finishes of old plastered surfaces, preparation of old surfaces on wall / ceiling / chajjas and applying two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 Ltre/10 Sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 Sqm over as per the manufacturer instruction complete all as specified and as directed. |
| 42 | M&L preparation of Old decorated surface of ceiling and applying two coats of White wash complete all as specified and as dirtected |
| 43 | Taking down chowkat with shutter without taking off shutter from the frame exc 1.5 sqm and n. exc. 4.00sqm each, complete all as specified and as directed. |
| 44 | S&F 1.25mm thick pressed steel frame for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc., complete with one shop coat of zinc chrome primer complete all as specified and as directed. |
| 45 | S&F 1.25mm thick pressed steel frame for doors with one or more rebates including necessary lugs, hinges, lock strike plate, etc., complete with one shop coat of zinc chrome primer complete all as specified and as directed. |
| 46 | S&F 30mm thick hard wood factory made flush shutters, solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed. |
| 47 | S&F factory made 35mm thick 2nd class hard wood gauged and skeleton shutter open rebated and prepared to received gauge etc (without sash bars) for fly proof door shutter, edges of framing plain, chamfered or rounded, fitted with cut of any mitred beads for securing gauge etc, size of members of shutter as specified in SSR-I section 8 clause No. 8.24(a) and fitted to chowkats complete all as specified and as directed. |
| 48 | M & L for providing plain cement concrete type C-1, 1:3:6, (using 20 mm graded stone aggregate), as in copings, bed block for filing hollow space of steel chowkhats, fixing of hold fast, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles & throating as directed including necessary form work as required complete all as specified and as directed. |
| 49 | Taking down of shutters of any description exc 1 sqm and n exc 2 sqm complete all as specified and as directed |
| 50 | S&F aluminium handles 125 mm size, cast type, anodised complete all as specified and as directed. |
| 51 | M&L Aluminium alloy anodised handle fabricated type 150mm long complete all as specified and as directed. |
| 52 | S&F 100 mm but hinges stainless steel complete all as specified and as directed. |
| 53 | S&F 150mm long aluminium anodised barrel tower bolt of extruded section fixed complete all as specified and as directed. |
| 54 | S&F 300mm Aluminium anodised sliding door bolt, with hasp & staple (bolt type) and fixing clips of sheet, cast of extruded sections and fixing bolts and sliding bolts of extruded sections complete all as specified and as directed. |
| 55 | S&F of Solid PVC Door Frame of size 50mm x 47mm made out of 5mm thick plain colour printed PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing as specified in part 8 & SSR part-I complete all as specified and as directed. |
| 56 | S& F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, wood free EPS as per specifications and drawing as specified in SSR Part I, Section 8 complete all as directed. |
| 57 | S&F factory made solid PVC frame of size 50mm x 47mm with a wall thickness of 5mm made out of extruded 5 mm thick PVC sheet of density 600Kg/cbm having pattam width of 50mm and thickness of 10mm. All three frame length reinforced with 19mm x 19mm MS square tube of 19 gauge. mitre cut at two corners and joined with two nos of 150mm long brackets of 15X15mm MS square tube or joint by fusion hit welding. The door frame shall be fixed to the wall thickness using 8Xthroughout the frame and metre cut at two corners and jointed with 2 nos of 150mm long brackets of 15mm x 15mm MS square tubes.The door frame shall be fixed to the wall using 8/100mm long MS screws through the frame by using PVC fasteners. A minimum 4 nos of screws to be provided for each vertical member and minimum 2 nos of screws to be provided to the horizontal member etc.complete all as specified and directed. |
| 58 | M&L factory made solid PVC cup board shutter (Flush type) of 24 mm thick made from co-extruded 3 layer regid PVC foam sheet (single extruded) with density not less than 600kg/cbm outer layer (8-1 mm) thick should be of rigid PVC with density of not less than 1400kg/cbm manufactured byan ISO 9001-2015 certfied company. Door should be water proof,turmite proof, fire retardant and having good screw holding capacity all as specified. |
| 59 | Supply and fixing Factory made single uPVC white colour Three track panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels ) upto 1.50m height made of ( big series ) frame 116x45 mm & sash 46x62mm both having wall thickness of 2.3mm + 0.2mm and single glazing bead / double glazing bead of appropriate dimension . (area of window above 1.75 sqm ) comprising of uPVC multichambered frame , with inbuilt roller track and sash extruded profiles duly reinforced with 1,60+0.20mm thick galvanised mild steel section made from roll forming process of required length ( shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks , EPDM gasket , wool pile zinc alloy ( white powder coated ) touch locks with hook , zinc alloy body with single nylon rollers ( weight bearing capacity to be 40 kg ) , GI fasteners 100x8mm size for fixing frame to finished wall and necesarry stainless screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of after fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality , complete all as specified and as directed.Note :- (i) Glass or wiremesh shall be paid separately (ii) For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e , in depth & width of profile shall be accepted but no extra payment on this account shall be made.) |
| 60 | S&F 4mm thick tinted glass, fixed with existing snap beading, rubber gasket etc. area of each pane n exc. 0.50 sqm complete all as specified and as directed. |
| 61 | Supply and fixing Factory made single uPVC white colour Two track Two panels door made of (big series) frame 67x50mm & sash 46x82mm both having wall thickness of 2.3mm + 0.2mm and single glazing bead / double glazing bead of appropriate dimension . (area of door above 2.00sqm upto 5.00sqm) comprising of uPVC multichambered frame , with inbuilt roller track and sash extruded profiles duly reinforced with 1.60+0.20mm thick galvanised mild steel section made from roll forming process of required length ( shape & size according to uPVC profile), appropriate dimension of uPVC, extruded glazing beads and uPVC extruded interlocks and uPVC extruded line sash adapter (if required) , EPDM gasket , wool pile zinc alloy ( white powder coated ) handle with on one side of the extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated)cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylone rollers ( weight bearing capacity to be 120 kg ) , GI fasteners 100x8mm size for fixing frame to finished wall and necesarry stainless screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality , complete all as specified and directed Note :-(i) Glass or wiremesh shall be paid separately (ii) For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e , in depth & width of profile shall be accepted but no extra payment on this account shall be made.) |
| 62 | S&F 5.5mm thick tinted glass, fixed with existing snap beading, rubber gasket etc. area of each pane exc. 0.50 sqm complete all as specified and as directed. |
| 63 | S&F anodised aluminium louvered ventilators of any size with glass louvers, without sash bars of aluminium sections weighing not less than 0.605kg/m for frame of size 40x20x2mm including necessary jointing cleats, glazing cleats, rubber packing , anodised aluminium snap beading,screws, anodised aluminium fittings and 4mm thick tinted glass fixed in panels with suitable locking arrangements including taking down of old existing ventilator and making good disturbed surface of wall complete all as specified and as directed. |
| 64 | Dismantling wrought iron or mild steel work of any description not otherwise provided for etc complete all as specified and as directed |
| 65 | S&F mild steel conforming to Fe.290.Gde-E-165 Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work complete all as specified and as directed. |
| 66 | S&F welded steel wire fabric weight not exc 4.00 kg/Sqm and fixed to wood or steel membera complete all as specified and directed |
| 67 | M&L framed work in tubular trusses such as roof trusses,trussed,purlines, crane gantries, rails and fastenings and heavy bracket framing including distance pieces, cleats etcs including special shaped washers etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St 240 complete all as specified and as directed. |
| 68 | S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws including necessary dismantling existing sheet complete all as specified and as directed. |
| 69 | M&L preparation of new surface of steel any description over 10 cm in width or girth not otherwise described two coat of synthetic enamel paint over a coat of red oxide complete specified and as directed. |
| 70 | Supply and fix in repairs sinks with drainage board made of stainless steel 1mm thick sheet plugs, washers and waste pipe, including a pair of cantilever brackets embedded in wall with suitable size of PCC (1:3:6) type C-1 blocks and connecting union to pipe of overall size 915mm x 460mm & bowl size 410mm x 330mm x 160mm all complete as specified and as directed |
| 71 | S&F in repairs vitreous china squatting pan\\"Orissa\\" pattern size 580x440mm white with intgeral foot rests(excluding flushing cistern and flush pipe) with 'P' or 'S\\" trap fron or back inlet etc including connection to trap tand flushing pipe and provision of cement concrete bedding (1:5:10) type E-2 complete all as specified and as directed including demolition of existing concrete complete all as specified and as directed. |
| 72 | S&F in repair 10 ltr capacity PVC flushing cistern low level white colour with inlet ball valve float and handle including brackets, flush pipe, including PTMT connection 450 mm long, PVC flush pipe of reqd length ,and connections to pipe etc complete all as specified and directed. |
| 73 | S&F in repairs 15mm dia fancy type Bib taps, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and as directed. |
| 74 | S&F in repairs15 mm dia CP cast copper alloy angle cock screwd for iron pipe and fixed complete all as specified and as directed. |
| 75 | S&F vitreous china wash basin Table top, white oval shape including waste chain and plug and porcelain stopper but including brackets, waste pipe & CP waste coupling, PTMT connection 450 mm long complete all as specified and as directed. |
| 76 | S&F in repairs 15 mm bore pillar taps, swan neck type with standared size capstan head, cast Copper alloy, chromium plated, screwed down high pressure with or without lettered ‘HOT’ or ‘COLD’ long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed. |
| 77 | S&F in repair, Brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flange complete all as specified and directed. |
| 78 | S&F in repairs PVC connection pipe 15mm size with PTMT nuts of length 450mm complete all as specified and directed. |
| 79 | S & F grating doom 125mm dia with waste hole of PTMT (min wt 40 gms) complete all as specified and as directed. |
| 80 | Taking down PVC Rain water pipes pipes 75/100 mm dia complete all as specified and as directed. |
| 81 | S&F 75 mm PVC(SWR) pipe socketed in any length with rubber ring joints, fixed to wall or in floors complete all as specified and as directed |
| 82 | S&F 110 mm bore PVC (SWR) pipes single sockets in any length with rubber ring joints fixed to wall or laid in floor complete all as specified and as directed. |
| 83 | S&F PVC(SWR) 75mm bore bends,diminishing pieces or tapers complete all as specified and as directed. |
| 84 | S&F PVC(SWR) 110mm bore bends,diminishing pieces or tapers complete all as specified and as directed. |
| 85 | S&F of PVC (SWR) floor trap, plain with CP grating including jointing with solvent cement outer dia 75mm cement concrete (1:2:4) type B-1 including complete all as specified and as directed. |
| 86 | Taking down PVC soil pipe with fittings from any position complete all as specified and as directed. |
| 87 | S & F 200mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls with necessary clamps etc complete all as specified and as directed. |
| 88 | S & F 200 mm bore PVC (SWR) bends of any radius, complete all as specified and as directed. |
| 89 | M&L cement concrete type C-2 1:3:6, 40mm graded aggregate as in surface channel & drains complete all as specified and as directed. |
| 90 | M & L prepration of old treated steel surface of any description exceeding 10cm width or girth and applying one coat of synthetic enamelled paint including complete all as specified and as directed. |
| 91 | M & L for preparation of old treated wood or wood based surface of any description exceeding 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 92 | Hacking out old broken unserviceable glass panes (any thickness, size, quality or description) for metal frame including punching or drilling out old glazing pins/spring clips complete all as specified and as directed. |
| 93 | S&F of 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square n.exc 0.5 sqm in each pane complete all as directed. |
| 94 | S&F stainles steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and as directed. |
| 95 | S&F in repair stainless steel curtain rod 20 mm dia, thick not less than 0.6mm mild steel chromium plated with fixing brackets, stops,rollers etc. complete all as specified and as directed. |
| 96 | M&L for providing plain cement concrete type B0 1:2:4 with using 12.5mm graded stone aggregates in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed. |
| 97 | S&F beveled edge looking mirror of 6mm thick selected quality glass, and fixed to stainless steel fancy plugs with chromium plated brass screws and cup washers, complete all as specified and as directed. |
| 98 | Demolition of RCC of ant description in any position including reinforcement cut as required to facilitate demolition complete all as specified and as directed. |
| 99 | M&L RCC 1:1.5:3 Type A1 ( using 20 mm graded stone agg) as chajjas including necessary formwork as reqd complete all as specified and as directed. |
| 100 | M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed |
| 101 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc for taking credit ( credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc complete all as specified and as directed. |
| 102 | M&L concealed point wiring complete for one socket outlet 15/16 Amps point on independent board with 4 Sqmm multistranded copper conductor single core PVC insulated unsheathed FR-LSH cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LSH (ISI marked) as earth continuity conductor connected to common earth dolly, fabricated sunken terminal box made out of 1.2mm thick MS sheet of appropriate size duly painted with aluminium paint inside and anti corrosive paint outside flush to wall with 3.0mm thick bakelite/plastic laminated sheet fixed with brass screws for housing switches, socket outlets, etc duly earthed including sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. complete all as specified and as directed. complete all as specified and as directed Note:-(i) Connections of cable with MCBs or bus bar shall be sone through proper size of copper/brass thimbles. (ii) Where concealing of conduit is not feasible ie on surface of roof etc, conduit shall be fixed on surface with necessary saddles at no extra cost |
| 103 | M&L concealed point wiring One light point controlled by one way switch 5/6 amps complete with 1.5 Sqmm multistranded copper conductor single core PVC insulated unsheathed FR-LSH cable 1100 volts grade (ISI marked) with proper colour coding drawn through and including non-metallic rigid PVC medium grade conduit not less that 20mm dia and conduit accessories (ISI marked) concealed in wall/fixed to roof, ceiling etc including provision of 1.5 Sqmm PVC insulated multistranded unsheathed copper conductor cable FR-LSH (ISI marked) as earth continuity conductor connected to common earth dolly, fabricated sunken terminal box made out of 1.2mm thick MS sheet of appropriate size duly painted with aluminium paint inside and anti corrosive paint outside flush to wall with 3.0mm thick bakelite/plastic laminated sheet fixed with brass screws for housing switches, socket outlets, fan regulators etc duly earthed including sinking for boxes and making good to the disturbed surface of wall/floor and matching with existing specifications. complete all as specified and as directed. complete all as specified and as directed Note:- (i) Connections of cable with MCBs or bus bar shall be sone through proper size of copper/brass thimbles. (ii) Where concealing of conduit is not feasible ie on surface of RCC roof/ceiling etc, conduit shall be fixed on surface with necessary saddles at no extra cost |
| 104 | All as per item No 104 here in before but for one 3 point 5 Amps switch socket outlet point controlled by one way switch on the independent board. |
| 105 | All as per item No 104 here in before but for one 3 point 5 Amps switch socket outlet point controlled by one way switch on the same board. |
| 106 | All as per item No 104 here-in-above but using 2.5 sq mm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for 5/15 amps switch socket combination point including running of 2.5 sq mm copper conductor flame retardant PVC wire as earth continuity conductor along with wiring and connecting to the common earth dolly complete all as specified and as directed. |
| 107 | S&F switch piano single pole flush type 5/6 amps, single pole on way complete all as specified and as directed |
| 108 | S&F socket outlet 2 in 1, 5 Pin, 5/6 amps, white ivory finish flush type complete all as specified and as directed. |
| 109 | S&F socket outlet 2 in 1, 5 Pin 5/15 amps multipurpose 230 volt flush type complete all as specified and as directed. |
| 110 | S&F switch piano flush type 15/16 amps single pole one way complete all as specified and as directed. |
| 111 | S&F in ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and as directed. |
| 112 | S & F lamp holder, insulated body, with back plate suitable for batten/angle fittings complete all as specified and as directed. |
| 113 | S&F LED white glass Lamp 1x9 Watt 230V Base-22 complete all as specified and directed. |
| 114 | S&F IP 20, class I, LED light 1X18 W (or nearest next higher wattage) (4feet). 5700K, wall/ surface mounted, integrated type with aluminium housing and decorative and caps with integrated high efficiency electronic driver and surge suppressor of 2KV or more, luminaire efficiency > 95 lumens/watt, power factor > 0.90, operating range - 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/ square blocks, screws etc complete with all accessories internally prewired and connecting up with and including necessary taking down the old unserviceable fitting complete all as specified. |
| 115 | S&F Inverter retrofit LED light of 20W with square profile and polycarbonate channel, lithium Ion battery with charging time 8 Hours-10 Hours and backup time upto 4 Hours with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose including taking down/dismantling of old existing unserviceable one complete all as specified and as directed. |
| 116 | S&F IP 20, Class I, LED Mirror light fitting 1 x 10 W, (or nearest next higher wattage) 5700 K, wall /Surface mounted with aluminium housing 2 feet long, integrated type, with high efficiency PMMA diffuser, integrated high efficiency electronic driver & surge suppressor of 2 KV or more, luminaire efficacy > 95 lumens/Watt, power factor >/ 0.90. operating range 140 to 270 V, 50 Hz fixed with 02 Nos of PVC round/square blocks, screws etc complete including 01 No 10 W LED lamp with all accessories internally prewired and including connecting up with and including twin core twisted flexible copper conductor cable of suitable size including necessary taking down the old unserviceable fitting complete all as specified. |
| 117 | S&F Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 35 watts (or nearest next higher wattage) with pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting and Gl pipe bracket made out of Gi pipe medium grade 32 mm dia 1.5 mtr long bend to required shape complete including taking out old unserviceable fitting all as directed |
| 118 | Taking down carefully Ceiling fan from its original position and refixing/hanging after repair work of bldg complete all as specified and directed. |
| 119 | M&L Painting of ceiling fans complete, with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc., all as specified and as directed. |
| 120 | Taking down carefull Exhaust fan from its original position and refixing it after making in serviceable condition to the same position after B/R repair work complete all as specified and directed. |
| 121 | M&L sheet metal enclosure fabricated out of 2.0 mm thick CRCA sheet, totally enclosed type, dust & vermin proof, with suitable sized supporting MS angles & suitable openings at top & bottom for entry of outgoing / incomming cables, fixed with nuts & bolts & front side openable with hinged shutter with suitable locking arrangement duly painted with 2 coats of powder coated paint over a coat of red oxide primer (spray paint) with minimum dimensions (90 x 75 x 20 cm ) flush to wall for incorporating 01 No TPN DB, 04 Nos electronic meters etc complete all as specified and as directed. |
| 122 | S&F sheet metal enclosure MCB DB TPN 4 way with 200 amps rated bus bar 415 volts double door complete including removal of old unserviceable sheet metal enclosure complete all as specified and as directed. |
| 123 | S&F sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with S&F MCB distribution boards (DBs) with sheet metal enclosure, double door, IP 43 protection, 240 Volts, 8 way, single pole and neutral, with 200 Amps rated copper bus bar (as per OEM), neutral link, earth link earthing studs, suitable for fixing MCBs, without MCBs fixed flush to wall/other surface including removal of old unserviceable sheet metal enclosure complete all as specified and as directed. |
| 124 | S&F MCB, Triple pole & neutral 63 amps, 240 volts, ‘C’ curve, 10KA including taking down and unserviceable one complete all as specified and as directed. |
| 125 | S&F MCB, Single pole & neutral, 35 to 63 amps, 240 volts, ‘C’ curve, 10KA including taking down old unserviceable one as specified and as directed. |
| 126 | S&F MCB, Single pole, 5 to 32 amps, 240 volts, ‘C’ curve, 10 KA including taking down old unserviceable one as specified and as directed. |
| 127 | M&L concealed sub-main wiring alongwith earth wire of size of 2 x 4.00sq. mm + 1 x 4.00 sq. mm earth wire, ISI marked, FRLSH, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC rigid conduit (medium grade) of suitable size with all fittings and accessories ISI marked including taking out old unserviceable submain wiring and making good to walls, floors etc as per existing specifications complete all as specified and as directed. NOTE : (i) Two runs of PVC wire, one run of earth wire & one run of PVC Conduit will be measured as one length.(ii) Cost of cutting chases and making good the distrubed surfaces of wall is deemed to be inclusive in the unit rate quoted |
| 128 | M&L concealed sub-main wiring alongwith earth wire of size of 2 x 6.00sq. mm + 1 x 6.00 sq. mm earth wire, ISI marked, FRLSH, PVC insulated, multi stranded, copper conductor, single core cable drawn through and including PVC rigid conduit (medium grade) of suitable size with all fittings and accessories ISI marked including taking out old unserviceable submain wiring and making good to walls, floors etc as per existing specifications complete all as specified and as directed. NOTE : (i) Two runs of PVC wire, one run of earth wire & one run of PVC Conduit will be measured as one length.(ii) Cost of cutting chases and making good the distrubed surfaces of wall is deemed to be inclusive in the unit rate quoted |
| 129 | S&F epoxy powder coated sheet metal enclosure with socket plug top and MCB, single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 32 Amps, 240 Volts, C Series current carrying capacity 10 kA, including necessary connection complete all as specified and directed. |
| 130 | M&L for earthing complete with galvanized steel plate electrodes of size600x600x6mm thick buried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised wire 4.00 mm earth lead by means of nuts, bolts, check nuts and washers of galvanized iron or steel all as shown in electrical plate No-5 of SSR Part-I including necessary excavation and earth work, PCC 1:3:6 type C-1 with 50mm thick pre-cast RCC cover 1:2:4 type B-1 cover slab reinforced with 8 mm dia TMT bar @ 15cm C/C both ways with suitable handle of 10mm dia MS rod including providing charcoal or coke & common salt in alternate layer of 15cm compacted thickness all around the earth electrode with funnel and 20mm bore (light grade GI watering pipe wire mesh, aluminium lugs complete in all respect GI earth wire protected by 15mm bore GI pipe and other end connected with main switch/ earth test pont, including dismantling old unserviceable earth pit complete all as specified and as directed. |
| 131 | Taking Down electric water Heater any type /size and refixing in position often complete of B/R repair work complete all as specified andas directed, |
| 132 | Taking out old unserviceable cable of any size carefully from trenches ofter disconnecting electric connection, Gi pipe protection, with and including separating serviceable bricks & set aside and removing un-serviceable bricks from site complete all as specified and as directed. Note: The Excavation and earth work shall be mesured and paid separately under relevant item of Schedule. |
| 133 | Supply, laying, jointing & testing in trenches or passing through pipe, 1100 volts grade, XLPE insulated PVC bedded,galvanized steel strip or wire armoured LT electric power UG cables, heavy duty with stranded aluminium conductor of cross sectional area 50 sqmm 3.5 core with and including all fixing & connecting accessories such as Alluminium cable lugs, cable gland, nut, bolts, washer etc complete as specified and as directed. ( NOTE: Earthwork & Excavation, Gl pipe, bricks for protection etc shall be measured and paid separately under relevant items of this schedule 'A'). |
| 134 | Excavation in trenches in soft/loose soil not exc. 1.5 metre wide and not exc. 1.5 metre in depth and getting out for taking up/laying under ground electric cable complete all as specified and as directed. |
| 135 | Returning, filling in, including spreading levelling watering and well rammming in layers not exceeding 25 cm as in soft/loose in depth complete all as specified and as directed. |
| 136 | Removing surplus soil to a distance not exceeding 50 mtr and depositing where directed at a level not exc 1.5 mtr above the starting point complete all as specified and as directed |
| 137 | M&L providing sand cushioning for protection of UG cable (8 cm deep before laying & 15 cm above the top edge of cable after laying) in trenches with dry (coarse) sand approved quality including filling, spreading and punning down to desired thickness complete all as specified & as directed. (NOTE : Punned thickness of 18 cm only shall be considered for payment purpose) |
| 138 | Supply and laying sub class B bricks available best quality brick in trenches for protection of UG cable with width equal to length of bricks as mechanical protection laid dry and flat complete all as specified and as directed. |
| 139 | M&L horizontal boring across the existing road without disturbing the road surface for inserting Gl pipe complete all as specified and as directed. Note:- (i) Removal of surplus soil shall be deemed to be include in the unit Rate. (ii) Gl pipe will be measured and paid separately under relevant item of Sch 'A'. |
| 140 | M&L 50 mm bore steel tubing light grade ISI marked for protection of cable including necessary joints complete all as specified and as directed |
| 141 | Taking out old unserviceable GI Pipe of any size from site complete all as specified and as directed. Note : The Excavation and earth work shall be measured and paid separately under relevant item of Schedule. |
| 142 | Supply and laying pipe galvanized, Medium grade including fittings 20 mm fixed complete to walls and ceiling or laid in floor directed. |
| 143 | Supply and laying pipe galvanized, Medium grade including fittings 25 mm fixed complete to walls and ceiling or laid in floor directed |
| 144 | Supply and fix Gun metal ,globe Gate Valves with iron wheel head of 20 mm dia bore complete with all accessories all as specified and directed. |
| 145 | Supply and fix Gun metal ,globe Gate Valves with iron wheel head of 25 mm dia bore complete with all accessories all as specified and directed. |
| 146 | M& L for cutting existing GI pipe alteration or addition of 100 mm dia bore for inerstion of reducer Tee complete with all accessories all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 31, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 16 daysNov 02, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 18 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender