Tender For Provn Of Ors Toilet And Bathroom Block Near Bldg No T-258 At Certain Mil Unit, Provn Of Pathway With Interlocking Tiles Along With Overhead Shed And Stainless Steel Grill From Bldg No P-110 (Or Recreation Room) To Bldg Nop-133 (Bathroom) A
Tender Value
37.97 Lakhs
Estimated cost
Bid Submission
28 Oct 2026
10 days left
EMD
76000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalpaiguri → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Ors Toilet And Bathroom Block Near Bldg No T-258 At Certain Mil Unit, Provn Of Pathway With Interlocking Tiles Along With Overhead Shed And Stainless Steel Grill From Bldg No P-110 (Or Recreation Room) To Bldg Nop-133 (Bathroom) And T-54 At Imtrat Wksp Eme In Jaigaon Mil Stn, Provn Of Store Room For Stn Canteen At Certain Mil Unit In Hasimara Mil Stn, Provn Of Training Store Near Bldg No T-315 At Certain Mil Unit In Hasimara Mil Stn And Provn Of Open Shed To Cover The Stage Of Pt Ground Length 11 Mtr, Width 6 Mtr And 66 Sqm At Certain Mil Unit In Hasimara Mil Stn Under Ge (S) Binnaguri
BOQ
| Sl. No. | Item Description |
| 1 | M&L for surface dressing n exc 15 cm deep for adjoining area complete all as specified |
| 2 | Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in soft/loose soil. |
| 3 | Returning filling in, incl spreading, levelling watering & well ramming in layers n.exc 25cm in soft/loose soil complete all as specified |
| 4 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified |
| 5 | M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified |
| 6 | M&L fly ash Brick work using modular size bricks with sub class 'B' bricks curved on plan with mean radius not exc 6m with bricks roughly cut to radius or bricks with wedge shaped joints built in cement mortar 1:6 complete all as specified |
| 7 | M&L for RCC (nominal mix) 1:1.50:3. type B1 using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified Note - Reinforcement and form work shall be measured and paid separately. |
| 8 | M&L for RCC (nominal mix) 1:2:4 type B1 using 20 mm graded stone aggregate as in beam, cantilevers, bressummers, lintels over 1.5 m span and similar work complete all as specified Note - Reinforcement and form work shall be measured and paid separately. |
| 9 | M&L for RCC nominal mix type A1,1:1.5:3 using 20mm gradded aggregate Slabs supported on walls, beams and columns in floors, shelves, platform, lintel, deck slabs and the like. |
| 10 | Form work to sides and soffits of floor or roof beam, beam hauchings, girders, bressummers, lintels, cantilevers, shelves, for flat rough finished concrete surfaces complete all as specified |
| 11 | Form work to sides of concrete foundation ,footings, bases of columns, raft and raft beams sides and soffits (if any )of foundation and plinth beams for flat rough finished concrete surface complete all as specified |
| 12 | M&L for RCC (nominal mix) 1:2:4 type B1 using 20 mm graded stone aggregate as in chajjas and similar work complete all as specified Note - Reinforcement and form work shall be measured and paid separately. |
| 13 | Form work to chullah hood, chajjas, troughs and similar items including edges etc for rough finished flat concrete surface complete all as specified |
| 14 | Mild Steel TMT bar 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified |
| 15 | Mild Steel TMT bar 6 to 8 mm dia cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified |
| 16 | Mild Steel TMT bar 5mm dia and over upto and including 10mm dia as in stirrups, spacers & binders cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified |
| 17 | M&L for 40 mm thick in Cement concrete 1:2:4, type B-0 Damp proof course to horizontal or vertical surfaces including necessary formwork and mixed with water proofing compound 0.25Ltr/ Sqm or as per manufacturer's instructions complete all as specified. (Note: Water proofing compound shall be measured and paid seperately under relevant item of schedule 'A'). |
| 18 | M&L for 20 mm thick plaster of cement mortar (1:4) rendering on fair faces of brick work in two layers (10mm & 10mm) mixed with water proofing compound in top layer 200 ml per beg of cement or as per manufacturer's instructions finishing the surface fair and even without using extra cement complete all as specified . (Note: Water proofing compound shall be measured and paid seperately under relevant item of schedule 'A'). |
| 19 | Supply only Liquid water proofing compound all as specified |
| 20 | M&L 15mm thick rendering in cement mortar 1:6 on other than fair face of brick work or concrete surface finished fair and even (without using extra cement) complete all as specified |
| 21 | M & L for preparing newly plastered surfaces of walls and applying three coats of white wash.on wall all as specified |
| 22 | M & L for preparing new Plastered surfaces of walls and applying two coat of cement base paint on surface of wal all as specified |
| 23 | M & L for preparing new Plastered surfaces of walls and finishing the walls with Acrylic smooth exterior paint of required shade : New work (Two coats applied over and including priming coat of exterior primer applied ). Make of Weather proof exterior acrylic emulsion and primer : Asian Apex Ultima/Berger weather coat long life 10 all as specified |
| 24 | S & F Structural steel work in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Fe 410-W (Gde -E-250 quality- A) Add to any of the foregoing items if structural steel is painted one shop coat of zinc chromate primer paint (including preparation of surface) at Contractor’s workshop before fabrication all as specified |
| 25 | S & F MS Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming to Fe-410-W (Gde E-250 quality B) with riveted, bolted or welded attachment complete all as specified |
| 26 | M&L of two coat of synthetic enamel paint over one coat of red oxide on new steel surfaces of any description over 10cm in width or girth incl preparation of surfaces complete all as specified |
| 27 | S & F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in roof covering/ cladding/ eaves board fixed with selp tapping screw complete all as specified |
| 28 | S & F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in roof covering/cladding/eaves board fixed with selp tapping screw complete all as specified |
| 29 | Supply and fixing aluminium anodised snap grid false ceiling to support the boards / tiles with aluminium Tee section 35 mm x 25 mm x 1.40 mm cross Tee 23.50 mm x 23.50 mm x 1.40 mm and aluminium angle 25 mm x 25 mm x 1.40 mm as on edge / sides including hanging proper hanging arrangement with 4 mm dia anodized galvanised iron wire and adjuster complete as specified. |
| 30 | S&F Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified all as specified. |
| 31 | M&L for Non asbestos fibre cement building boards fixed or laid/ inserted to timber/GI/Aluminium framework with screws ,4mm thick designer board (610mm x 610mm ) size complete all as specified |
| 32 | M&L for Moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including wateringcomplete all as specified |
| 33 | M & L for hardcore guage of broken stone or boulders of exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface. |
| 34 | M&L for 100 mm thick Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified . |
| 35 | M&L for Machine cut kota stone slab flooring mirror finished 20-25 mm thick (each slab not less than 0.25 sqm) over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and 15 mm thick screed bed or bedding layer in CM 1:4 surface finished fair and even for laying floor finishescomplete all as specified |
| 36 | M&L for Machine cut kota stone in riser of steps, skirting, dado and pillar mirror finished 20-25 mm thick over cement base rendering laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and including rendering 10 mm thick in cement mortor 1:4 complete all as specified . complete all as specified Please Enable Macros to View BoQ information |
| 37 | M&L for Machine cut kota stone in riser of steps, skirting, dado and pillar mirror finished 20-25 mm thick over cement base rendering laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and including rendering 10 mm thick in cement mortor 1:4 complete all as specified . complete all as specified Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 10 daysNov 04, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 17 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender