Tender For Upgradation And Renovation Of Type-V Govt. Officers Flats At Greater Kailash-I Including Tile Work, Plaster Repairs, Surface Preparation, Painting, Replacement Of Old Doors/Windows, Modular Kitchen, Cupboards, Plumbing Works, Sanitary Fitt
Tender Value
4.62 Crore
Estimated cost
Bid Submission
14 Oct 2026
3 days left
EMD
9.24 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Delhi → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Upgradation And Renovation Of Type-V Govt. Officers Flats At Greater Kailash-I Including Tile Work, Plaster Repairs, Surface Preparation, Painting, Replacement Of Old Doors/Windows, Modular Kitchen, Cupboards, Plumbing Works, Sanitary Fittings/Fixtures And Allied Civil Works Under Sub-Division-V, Se(B)M Division, Pwd, New Delhi.
BOQ
| Sl. No. | Item Description |
| 1 | Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. |
| 2 | All kinds of soil |
| 3 | Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: |
| 4 | Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 5 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lif. |
| 6 | Surface dressing of the ground including removing vegetation and in- equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m. |
| 7 | All kinds of soil |
| 8 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : |
| 9 | 1:2:4 (1 cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 10 | 1:5:10 (1 cement : 5 coarse sand (zone-Ill) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 11 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: |
| 12 | Cement mortar 1: 6(1 cement :6 coarse sand) |
| 13 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : |
| 14 | Cement mortar 1:6(1 cement : 6 coarse sand) |
| 15 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. |
| 16 | Cement mortar 1:4(1 cement :4 coarse sand) |
| 17 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. |
| 18 | Granite stone slab of colour black, Cherry/Ruby red |
| 19 | Area of slab upto 0.50 sqnn |
| 20 | Area of slab over 0.50 sqm |
| 21 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 22 | Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : |
| 23 | Gang saw cut stone |
| 24 | 30 mm thick Red sand stone |
| 25 | Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with: |
| 26 | Decorative veneer facings of approved manufacture |
| 27 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3(1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 28 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). |
| 29 | Second class teak wood |
| 30 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: |
| 31 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 32 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured). |
| 33 | Providing and fixing special quality bright finished brass cupboard or ward robe locks with four levers of approved quality including necessary screws etc. complete. |
| 34 | 40 mm |
| 35 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 36 | Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. |
| 37 | Providing and fixing Bamboo jaffery/ fencing consisting of superior quality 25 mm dia (Average) half cut bamboo placed vertically and fixed together with three numbers horizontal running members of hollock wood in scantling of section 50X25 mm, fixed with nails and G.I wire on existing support complete as per direction of Engineer-in-charge. |
| 38 | Providing and fixing magnetic catcher of approved quality in cupboard/ ward robe shutters, including fixing with necessary screws etc. complete. |
| 39 | Double strip (horizontal type) |
| 40 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. |
| 41 | 1.0 mm thick |
| 42 | Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and lnline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 — Part 3 (ii) Sites with structure height more than 20m for all wind speeds |
| 43 | Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. |
| 44 | Using R3 series with frame (98 mm & above) x (40 mm & above) & both glazed and fly screen sash (30 mm & above) x (55 mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. (Height upto 1.8m). |
| 45 | Ventilator Casement window single panel with or without fixed panel with S.S. 304 friction hinges as per size and weight of sash, single point locking zinc alloy (zannak) powder coated handles. |
| 46 | Using R1 series with frame (33 mm & above) x (35 mm & above) & sash /mullion (33 mm & above) x (50 mm & above). (Height upto 0.90 metre). |
| 47 | Casement window single panel with S.S. 304 friction hinges as per size and weight of sash, multi-point locking system, zinc alloy (zamak) powder coated handles. |
| 48 | Using R2 series with frame (39 mm & above) x (39 mm & above) & sash (39 mm & above) x (60 mm & above). (Height upto 1.2 metre) |
| 49 | Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. |
| 50 | 100mm |
| 51 | Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-charge. |
| 52 | 200 mm |
| 53 | Providing and fixing stainless steel sof closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge. |
| 54 | Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per direction of Engineer- in-charge, |
| 55 | Providing and fixing ready made 304 grade stainless steel Modular kitchen basket and accessories such as right angle basket (Plain Cup & Saucer, plant, Partition, Bottle rack, Thali, Cutlery) kitchen utensil basket, Dinner set basket, kitchen grain basket, Multipurpose basket as per site requirement including finishing (wherever required) and fittings. The same shall be fixed with necessary stainless steel nuts & bolts, Stainless Steel screws & telescopic channel etc. as per direction of Engineer-in- charge. (For payment purpose only weight of Stainless steel basket shall be considered excluding weight of all fixing accessories such as nuts, bolts, fasteners telescopic basket channels etc. Payment of providing and fixing telescopic channel shall be paid separately) |
| 56 | Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. |
| 57 | Using M.S. angels 40x40x6 mm for diagonal braces |
| 58 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 59 | Hot finished welded type tubes |
| 60 | Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. |
| 61 | In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works |
| 62 | Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge. |
| 63 | 10 x 160 mm |
| 64 | Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, bufing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 65 | Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). |
| 66 | Ordinary cement without any pigment |
| 67 | Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : |
| 68 | 25 mm thick |
| 69 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. |
| 70 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 71 | Providing and laying Vitrified tiles in floor in diferent sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. |
| 72 | Double charge vitrified tile polished finish of size |
| 73 | Size of Tile 600 x 600 mm |
| 74 | Size of Tile 600 x 1200 mm |
| 75 | Size of Tile 800 x 1600 mm |
| 76 | Glazed Vitrified tiles Matt/Antiskid finish of size |
| 77 | Size of Tile 600 x 600 mm |
| 78 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 79 | 110 mm diameter |
| 80 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion. |
| 81 | Bend 87.5° |
| 82 | 110 mm bend |
| 83 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. |
| 84 | 110 mm |
| 85 | Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'S or 'L' hooks, bolts & nuts 8 mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafers, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified. |
| 86 | 2 mm thick flat |
| 87 | Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required. |
| 88 | 12 mm cement plaster of mix: |
| 89 | 1:6 (1 cement: 6 coarse sand) |
| 90 | 15 mm cement plaster on rough side of single or half brick wall of mix: |
| 91 | 1:6(1 cement: 6 coarse sand) |
| 92 | 6 mm cement plaster of mix: |
| 93 | 1:3(1 cement :3 fine sand) |
| 94 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete. |
| 95 | Finishing walls with Acrylic Smooth exterior paint of required shade: |
| 96 | New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) |
| 97 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : |
| 98 | Two or more coats on new work |
| 99 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 100 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. |
| 101 | One coat |
| 102 | Two coats |
| 103 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. |
| 104 | With ready mixed pink or grey primer on wood work (hard and soft wood) having VOC content less than 50 grams/ litre |
| 105 | With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre |
| 106 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 107 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: |
| 108 | One or more coats on old work |
| 109 | Melamine polishing on wood work (one or more coat). |
| 110 | Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following process in the sequence as detailed below: 1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2. Applying two coats of sealer with spray gun and allowing suficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further allowed to dry for 12 hrs. 4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. using melamine clear polish and melamine thinner mixed in required. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Final coat to be done in 1 or 2 layers without gap of time.) |
| 111 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. |
| 112 | With cement mortar 1:4 (1cement: 4 coarse sand) |
| 113 | Disconnecting damaged overhead/terrace PVC water storage tank of any size from water supply line and removing from the terrace including shifting at ground level as per direction of Engineer-in-charge. |
| 114 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials including malba all complete as per directions of Engineer-in-Charge. |
| 115 | Dismantling 15 to 40 mm dia G.I. pipe including stacking of dismantled pipes (within 50 metres lead) as per direction of Engineer-in-Charge. (a) Internal Work- Exposed on wall |
| 116 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 117 | Nominal concrete 1:3:6 or richer mix (including equivalent design mix) |
| 118 | Nominal concrete 1:4:8 or leaner mix (including equivalent design mix) |
| 119 | Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge. |
| 120 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. |
| 121 | In cement mortar |
| 122 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : |
| 123 | Of area 3 sq. metres and below |
| 124 | Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead. |
| 125 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. |
| 126 | For thickness of tiles 10 mm to 25 mm |
| 127 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. |
| 128 | Dismantling barbed wire or flexible wire rope in fencing including making rolls and stacking within 50 metres lead. |
| 129 | Dismantling wooden boardings in lining of walls and partitions, excluding supporting members but including stacking within 50 metres lead : |
| 130 | Thickness above 10 mm up to 25 mm |
| 131 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 132 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.Note: Payment will be made as per weight slip issued by authorised MCD dumping ground after dumping of malba. Processing fees at prescribed rate of authorised MCD dumping ground will be submitted by the agency & shall be reimbursed by the department on production of receipt in original. |
| 133 | Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used. |
| 134 | With G.I. barbed wire |
| 135 | Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sq. mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately) |
| 136 | Providing and laying 60 mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge. |
| 137 | Taking out existing CC interlocking paver blocks from footpath/ central verge, including removal of rubbish etc., disposal of unserviceable material to the dumping ground, for which payment shall be made separately and stacking of serviceable material within 50 metre lead as per direction of Engineer-in-Charge. |
| 138 | Laying old cement cocrete interlocking paver blocks of any design/ shape laid in required line, level, curvature, colour and pattern over and including 50 mm thick compacted bed of coarse sand, filling the joints with fine sand etc. all complete as per the direction of Engineer-in-charge. (Old CC paver blocks shall be supplied by the department free of cost). |
| 139 | Providing and laying matt finished vitrified tile of size 300x300x9.8 mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20 mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge. |
| 140 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : |
| 141 | Kitchen sink with drain board |
| 142 | 510x1040 mm bowl depth 225 mm |
| 143 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 144 | Flexible pipe |
| 145 | 32 mm dia |
| 146 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 147 | Providing and fixing soil, waste and vent pipes : |
| 148 | 100 mm dia |
| 149 | Sand cast iron S&S pipe as per IS: 1729 |
| 150 | Providing and filling the joints with spun yarn, cement slurry and cement mortar 1:2 ( 1 cement : 2 fine sand) in S.C.I./ C.I. Pipes : |
| 151 | 100 mm dia pipe |
| 152 | Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), including cost of cutting holes and making good the walls etc. : |
| 153 | For 100 mm dia pipe |
| 154 | Providing and fixing bend of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete. |
| 155 | 100 mm dia |
| 156 | Sand cast iron S&S as per IS - 1729 |
| 157 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 158 | 20 mm nominal dia Pipes |
| 159 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 160 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : |
| 161 | 100 mm diameter S.W. pipe |
| 162 | 150 mm diameter S.W. pipe |
| 163 | 200 mm diameter S.W. pipe |
| 164 | Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: |
| 165 | 100x100 mm size P type |
| 166 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 167 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : |
| 168 | Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : |
| 169 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 170 | Raising manhole cover and frame slab to required level including dismantling existing slab and making good the damage as required (Raising depth of manhole to be paid separately) : |
| 171 | Rectangular manhole 90x80 cm with rectangular cover 600 x 450 mm of grade LD - 2.5 |
| 172 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : |
| 173 | For fixed portion |
| 174 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 175 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) |
| 176 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 177 | Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. |
| 178 | Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side |
| 179 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): |
| 180 | With float glass panes of 4.0 mm thickness (weight not less than 10kg/sqm) |
| 181 | Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose particles with wire brushes, complete in all respect as per the direction of Engineer- in-Charge. |
| 182 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5 mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 183 | Frame size 50 x 100 mm |
| 184 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 185 | 30 mm thick |
| 186 | Providing & fixing factory made Modular Kitchen as per the enclosed drawings and following specifications:-(a) The horizontal and vertical partition/Member of frame of cabinets are made of 18 mm thick both side prelaminated HDHMR board. The shelves are made of 18 mm thick both side prelaminated HDHMR board.(b) The back member/panel of cabinet is made of 8 mm thick both side prelaminated BOILO board.(c) The front panel/shutter of cabinet is made of 18 mm thick one side (internal side) prelaminated HDHMR board.(d) The front side (outer side) of shutter is pasted with 1 mm thick laminate as per the shade/color approved by Engineer-in-Charge.(e) Stainless steel plain wire basket/Innotech for the units as shown in the enclosed drawings as per direction of Engineer-in-charge. The basket is capable of bearing the load as per requirement of the cabinet. The size of basket is such that it fits completely in the unit.(f) S-Carousel (Corner unit)/magic corner soft closing with two numbers trays designed to utilize the all space in the unit equivalent to shown in the enclosed drawing as per direction of Engineer-in-charge.(g) Stainless steel/Glass bottle pull out 200/2 shelf or as per space available.(h) Cutlery basket of size 600 mm or as per space available. (i) The units/cabinets are installed with necessary stainless steel screws.(j) The units are provided with necessary accessories and fittings such as handles (size 125-135 mm), soft closing hinges (Auto closing tape), heavy duty soft closing telescopic channels, etc. |
| 187 | (k) All the floor rested units are fixed with 100 mm size heavy duty legs.(l) All floor rested units are fixed with PVC skirting of 100 mm height to cover the gap between the floor and the unit. The skirting is fixed in such a way that it is easily removable and refixable allowing the user to clean the area below units.(m) The gap between the wall and units if any, is covered with the 18 mm thick both side prelaminated HDHMR board and white cement/silicon sealant.(n) The unit is fixed on wall/floor with sufficient number of rawl plugs/screws/steel fastener to make it stable.(o) Autolid dustbin of capacity 14 ltr. fixed inside the sink cabinet on one of the shutters.(p) Stainless steel detergent/rack fixed inside the sink unit on one of the shutters.(q) Stainless steel plate rack with drip tray of size 800 mm or as per space available.(r) The chimney and exhaust pipe is covered with shutter of 18 mm thick one side (inside) prelaminated HDHMR board. The outer side of shutter is pasted with 1 mm thick laminate as per the shade/color approved by Engineer-in-Charge. All the edges of board is pasted with edge banding tape fixed with the machine of approved color and thickness.The shelves of cabinet are fixed with the brackets with the help of necessary screws.The pantry cabinet is provided with 12 no. of stainless steel basket of size 600 mm or glass pantry unit as per space available (as per direction of Engineer-in-charge). The 6 no. of basket are fixed on shutter and other 6 no. basket are fixed inside the cabinet. These basket are fixed in such a way that these can be adjusted at different heights of pantry unit. Front elevation of each type of unit shall be measured for payment purpose. For the units as under:- |
| 188 | Top Plain Shelf Unit of 300mm Depth i/c P/F horizontal shelf of 18mm thick HDHMR and modify passage for chimey duct. |
| 189 | Bottom Shelf Unit with all required accessories SS Wire Basket/Innotech and S-Carousel Unit/Magic corner and B.P.O. Unit (As per direction of Engineer-in-charge.) |
| 190 | Top Unit with G.T. / P.T. 800mm Stainless Steel |
| 191 | Pantry Unit SOFT CLOSE 600 MM with SS Wire Basket/Glass pantry unit. |
| 192 | Loft Unit and bottom shelve unit (As per Approved Drawing) |
| 193 | Sink Unit (Part of Bottom Unit) having dustbin holder with SS dustbin of approx capacity of 14 litre & SS holder/Stand for Detergent/Clearner etc. Sink unit is to be fixed with slainless steel frame work in addition to the 18 mm thick both side prelaminated WPC board frame work with sink profile to provide additional strength to bear heavy load. |
| 194 | Providing and Fixing Factory made Room Cup Board of depth up to 600 mm, and height up to ceiling height, having the provision of racks, partition, drawer etc. as per the requirement of a standard cup board and as per the drawing approved by the Engineer-in-charge, (at all levels/floors) made of:- (A) 18 mm thick MDF (medium Density Fibre Board), which is one side decorative laminated and other side balancing laminated of approved make or as directed by Engineer-in-charge for shutter. (B) 18 mm thick HDHMR Board (High Density High Moisture Resistant Board), which is both side balancing laminated for top, bottom, sides, middle and shelf etc. of approved brand/quality, fixed with necessary S.S. screws and minifix to the wall/ Board etc. all complete to make a frame for drawer, shelf etc. (C) Back side of the Cabinet is made with 8mm thick BOILO Board of approved brand/quality fixed with necessary S.S. screws and minifix to the wall. Stainless Steel fancy Handles of 100 mm (design to be approved by Engineer-in-charge) are to be fixed on the Shutters. All the Edges of Shutters are covered with 2 mm thick PVC Edge binding, fixed with machine. Front edges of Top, Bottom, Sides, Middle and Shelfs are covered with 0.80 mm PVC Edge binding fixed with PVC binding glue. All the shutters shall be fixed to the frame with stainless steel soft closing spring hinges (Hydraulic type) of Approved Brand/make/size with full threaded steel screws including making necessary recess in board and finished all complete made of approved make by Engineer-in-charge. (Front surface area of shutter only to be measured for payment purpose.) (All required fittings, to make the cupboard functional/useable, are included in this item and no further payment in the name of fittings shall be made.) |
| 195 | Providing and Fixing Factory Made Room overhead Cup Board shutter including frame in existing opening of height up to 1.5 meter (at all levels/floors) made of :(A) 18 mm thick HDHMR Board (High Density High Moisture Resistance Board), which is one side decorative laminated and other side balancing laminated for shutter of approved brand/quality fixed with necessary screws and soft close hinges including providing and fixing necessary frame as directed by Engineer‐in‐charge. Stainless Steel fancy Handles of 100 mm (design to be approved by Engineer‐in‐charge) are to be fixed on the Shutters. All the Edges of Shutter are covered with 2 mm thick PVC Edge binding, fixed with machine. All the shutters shall be fixed to the frame with stainless steel soft closing spring hinges (Hydraulic type) of approved brand/make with full threaded steel screws including making necessary recess in board and finished all complete of approved make by Engineer‐in‐charge. (Front surface area of shutter only to be measured for payment purpose.). (All required fittings, to make the cupboard functional/useable, are included in this item and no further payment in the name of fittings shall be made). |
| 196 | Providing and laying 12 mm thick AC- 5, grade laminate wooden flooring & skirting of aciton tesa or equivalent made having 0.2 mm thick direct laminate on top of specially developed substrate core (high density fibre board) of plank size as per manufacturer's specification having smart lock, joint tongue and groove construction i/c top of skirting should be sealed with 4mm thick teak wood lipping. The under layer has to be a 0.2 mm thick alkali resistant polyethylene sheet of density 30-32 kg. per cum on top to secure the floor. The work shall be carried out as per manufacturer's installation procedure and as per direction of Engineer-in-charge. |
| 197 | Providing and fixing 16 mm thick laminated wooden beading over laminated wooden skirting complete. The work shall be carried out as per manufacturer’s installation procedure and as per the direction of Engineer-in-charge. |
| 198 | Dismentling old wall tiles of all size and thickness in cement mortar including racking out joints including removing the base plaster and preparing the surface for plaster including disposal of rubbish to the dumping point - within 50 m lead. |
| 199 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. |
| 200 | Glazed vitrified floor tiles polished finish of size Size of Tile 600 x 600 mm. |
| 201 | Glazed vitrified floor tiles polished finish of size Size of Tile 600 x 1200 mm. |
| 202 | Glazed vitrified floor tiles polished finish of size Size of Tile 800x1600 mm. |
| 203 | Providing and fixing fly proof stainless steel grade 304 wire gauge, to uPVC windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm fixed with existing uPVC beading (Cost of uPVC beading included in original uPVC Item) all complete as per directin of Engineer-in-charge. |
| 204 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters and similar locations of required size, approved shade, colour and texture to be fixed with adhesives, joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red of any size. |
| 205 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for window Jambs and soffit and similar locations of required size,approved shade, colour and texture laid over 12 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding (included all visible faces) and polishing to edges to give high gloss finish etc. complete at all levels. Granite stone slab of colour black, Cherry/Ruby red of any size |
| 206 | Providing and fixing 6mm Toughened Glass in aluminium/uPVC door, window, ventilator shutters and partitions etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading/upvc shall be paid in basic item): |
| 207 | Providing & fixing White Metal with black matt finished polish or required shade mortice latch and lock of GODREJ make CAT No. NEH 19-1 CK, with six levers including double sided cylinder and a pair of same material and shade lever handles of approved quality i/c all fittings complete as per direction of Engineer-in-charge. |
| 208 | Providing and fixing CP Brass Concealed body for high flow Divertor of JQUAR make Cat No. ALD-CHR-079N or equivalent make i/c making all connection complete as per direction of Engineer-in-charge. |
| 209 | Providing and fixing Single lever exposed parts Kit (for divertor) of JAQUAR make CAT No. ALI-CHR-85079NK or equivalent make i/c making all connection complete as per direction of Engineer-in-charge. |
| 210 | Provding and fixing Single Lever Basin mixer Tall Boy with 150mm Extension Body Fixed Spout without Popup Waste System with 600mm Long Braided Hoses JAQUAR make CAT No. OPP-CHR-15005BPM or equivalent make i/c making all connection complete as per direction of Engineer-in-charge. |
| 211 | Providing and fixing Toilet Roll Holder with Stainless Steel Flap of JAQUAR make CAT No. AKP-CHR-35753PS or equivalent make i/c making all fixing & screwing complete as per direction of Engineer-in-charge. |
| 212 | Providing and fixing CP Brass bottle trap of JAQUAR make CAT No. ALD-CHR-769L300x190 or equivalent make i/c making all connection complete as per direction of Engineer-in-charge. |
| 213 | Providing and fixing C.P. Brass Overhead Shower of JAQUAR make CAT No.OHS-CHR-1755 or equivalent make i/c. making all connection complete as per direction of Engineer-in-charge. |
| 214 | Providing and fixing Rimless single piece W.C. of JAQUAR make CAT No. FSS-WHT-29853S300UFSM or equivalent make i/c making all connection complete as per direction of Engineer-in-charge. |
| 215 | Providing and fixing Rimless single piece W.C. of JAQUAR make CAT No. OPS-WHT-15753P180UFPMZ or equivalent make i/c making all connection complete as per direction of Engineer-in-charge. |
| 216 | Providing and fixing Towel Ring of JAQUAR make CAT No. ACN-CHR-1121BN or equivalent make i/c all screws etc. complete as per direction of Engineer-in-charge. |
| 217 | Providing and fixing Glass Corner of JAQUAR make CAT No. VGP-CHR-81173B or equivalent make i/c all screws etc. complete as per direction of Engineer-in-charge. |
| 218 | Providing and fixing C.P. Brass Glass Shelf 600 mm (with brass brackets) of JAQUAR make CAT No. AKP-CHR-35771P or equivalent make i/c all fixing & screwing etc. complete as per direction of Engineer-in-charge. |
| 219 | Providing and fixing Towel Rack 600mm long with lower hangers of JAQUAR make CAT No. AKP-CHR-35781PS or equivalent make i/c making all fixng & screwing etc. complete as per direction of Engineer-in-charge. |
| 220 | Providing and fixing CP Brass Sink Mixture with regular turning & moving spout (Swing Spout) of JAQUAR make CAT No. FLP-CHR-5179BPM or equivalent make i/c making all connection complete as per direction of Engineer-in-charge. |
| 221 | Providing and fixing C.P. Brass Hand Shower (Health Faucet) with 1.2 mtr. Flexible Tube & Hook of JAQUAR make CAT No. ALD-CHR-563 or equivalent make i/c. making all connection complete as per direction of Engineer-in-charge. |
| 222 | Providing and fixing Table top wash basin of size 495x395x150 mm of JAQUAR make CAT No. JDS-WHT-2591 or equivalent make i/c making all connection complete as per direction of Engineer-in-charge. |
| 223 | Providing and fixing C.P. Brass Angle Cock with flange (Angular stop cock) of JAQUAR make CAT No. CQT-CHR-23053 i/c. making all connection complete as per direction of Engineer-in-charge. |
| 224 | Providing and fixing C.P. Brass Soap Dispenser of JAQUAR make CAT No. ACN-CHR-1137N i/c. all fixing & screwing etc. complete as per direction of Engineer-in-charge. |
| 225 | Providing and fixing C.P. Brass Soap Dish of JAQUAR make CAT No. AKP-CHR-35731P i/c. all fixing & screwing etc. complete as per direction of Engineer-in-charge. |
| 226 | Providing and fixing C.P. Brass waste coupling of JAQUAR make CAT No. ALD-CHR-705L130 i/c making all connection complete as per direction of Engineer-in-charge. |
| 227 | Providing and fixing C.P. Brass Shower Arm 375 mm Long of JAQUAR make CAT No. SHA-CHR-455L400 i/c. making all connection complete as per direction of Engineer-in-charge. |
| 228 | Providing and fixing Long Body Bib Cock with Wall Flange of JAQUAR make CAT No. COP-CHR-107NPM i/c. making all connection complete as per direction of Engineer-in-charge |
| 229 | 15 mm nominal bore |
| 230 | Providing and fixing Bib Cock with Nozzle & Wall Flange of JAQUAR make CAT No. COP-CHR-049NPM i/c. making all connection complete as per direction of Engineer-in-charge. |
| 231 | Providing and fixing Bathtub Spout of jaquar make cat No. SPJ-CHR-15429PM or equivalent make i/c. making all connection complete as per direction of Engineer-in-charge. |
| 232 | Providing and fixing Sliding bolt (Baby latch) with SS lock strip 05\\" of doorset make cat no. BL(B) or equivalent make i/c. making all connection complete as per direction of Engineer-in-charge. |
| 233 | Providing and fixing sliding door bolt of Stainless Steel grade 304 of dorset catalogue no. ALDSM 200x16 mm or equalant and approved make/quality with nuts and screws etc. all complete as per direction of Engineer-in-charge. (a) 200x16 mm |
| 234 | Providing and fixing hard drawn steel wire fabric 75x25 mm mesh including fixing the same with steel frame by electric welding of 1.50 centimetre length and priming coat with approved steel primer all complete. |
| 235 | Providing and Fixing 18 mm thick HDHMR Board (High Density High Moisture Resistance Board), which is one side decorative laminated and other side balancing laminated for cupboard/kitchen shutter of approved brand/quality (Action Tesa or equivalent) fixed with necessary SS screws and self closing hinges. All the Edges of shutters are cover with 2 mm thick PVC Edge binding, fixed with PVC binding glue. All the shutters are fixed with full threaded steel screws including making necessary recess in board and finished all complete as per direction of Engineer-in-charge. (Area of Each member to be measured for payment.) (SS fancy Handles , Basket , Drawer Channel, self closing hinges to be paid in original item) |
| 236 | Providing and Fixing 18 mm thick HDHMR Board (High Density High Moisture Resistant Board) , which is both side balancing laminated for top , bottom, sides, middle and shelf etc.for kitchen/cupboard approved brand/quality ( Action Tesa or equivalent) , fixed with necessary SS screws and minifix to the wall/ Board etc all complete to make a Frame. Front edge`s of Top, Bottom, Sides , Middle and Shelfs are covered with 0.80 mm PVC Edge binding fixed with PVC binding glue as per direction of Engineer-in-charge. (Each member area to be measured for payment.) |
| 237 | Providing and Fixing Back side of the Kitchen/cupboard cabinet is made with 5.50mm thick HDHMR BSB board (High Density High Moisture BSB Board) of approved brand/quality ( Action Tesa or equivalent). fixed with necessary SS screws and minifix to the wall as per direction of Engineer-in-charge. (Each member area to be measured for payment.) |
| 238 | Providing & fixing curtain rods of 1.25 mm thick stainless steel 304 grade of minimum weight 785 gm per meter with two or more stainless steel brackets and crowns, as per site requirement fixed with stainless steel screws and wooden plugs, etc., wherever required complete as per direction of Engineer-in-charge. |
| 239 | Providing and fixing unplasticised Rigid PVC pipes (6kg/cm²) for connecting GT and sewer line, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, |
| 240 | 110. mm dia Single socketed pipes |
| 241 | 160 mm dia Single socketed pipes |
| 242 | 200 mm dia Single socketed pipes |
| 243 | Granite work (Polished and machine cut) of thickness 18mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand) including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the granite shade: (To be secured to the backing by means of cramps, which shall be paid for separately). Granite of any colour and shade. (Sample and colour shall be approved by Engineer in charge) :Area of slab above 0.50 sqm |
| 244 | Deduct for taking away dismantled/broken polyethylene water storage tank excluding fittings. |
| 245 | Credit for Old Steel:- Bars, Z-section, Rolled steel sections, Structural Steel section, G.I. barbed wire, Expended metal/IRC fabric, CI/SCI pipes of various diameter, GI pipes of various diameter, CI pipes of various diameter (Broken in pieces), CI Manhole cover & frames( Broken in pieces) CI, DI, LA, etc. |
| 246 | Credit for Old timber scraped/Unserviceable |
| 247 | Credit for Old Aluminium Scrap/Unserviceable |
| 248 | Credit for Old Brass Scrap/Unserviceable |
| 249 | Credit for Wooden old door shutter |
| 250 | Modified Estimated Cost after using Correction factor on DSR-2023 on account of GST @ 0.973 |
| 251 | Add Cost Index @ 4.03% on DSR 2023 item. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 07, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 14, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysOct 14, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender