Tender For Recarpeting Of V-3 Road Between Sector 14 & 25 And Approch Road T-Point To Village Dhanas Chandigarh.
Tender Value
62.65 Lakhs
Estimated cost
Bid Submission
13 Oct 2026
4 days left
EMD
1.25 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Chandigarh → Chandigarh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Recarpeting Of V-3 Road Between Sector 14 & 25 And Approch Road T-Point To Village Dhanas Chandigarh.
BOQ
| Sl. No. | Item Description |
| 1 | Providing and laying type 3 (6mm to 8mm) 7 mm avg. Thick SLURRY SEAL with mechanical paver after mixing aggregate and bitumen in hot mix plant using 12 kg/sqm Straight run bitumen of VG-30 penetration 7.5% (by weight & qty aggregate) and using fine aggregate with 2% filler to the weight of aggregate confirming to relevant specification laid in MORT&H specification complete in all respect and to the entire satisfaction of the Engineer-in-charge. |
| 2 | Providing and laying tack coat with bitumen VG-10 @ 3.00 kg/10 sqm using sprayer pump on prepared surface heating bitumen in boiler and spraying bitumen with spray set fitted on bitumen boiler including cleaning of road surface with complete in all respect as per MORT&H specification and to the entire satisfaction of the Engineer-in-charge. |
| 3 | Providing and laying 30mm thick bituminous concrete as per clause 507 of MORT&H specification with mechanical paver after mixing aggregate and bitumen as per design mix in Hot mix plant using minimum 5.5% bitumen of grade VG- 30 and using both coarse and fine aggregate filler stone dust @2% by weight of aggregate confirming to relevant specification laid in MORT&H specification clause 507.2.2 and 507.2.3 with grading confirming to table 500.17 gradation –II of MORT&H specification and density of bituminous concrete as laid 2.35 gm/cc complete in all respect as per MORT&H specification and to entire satisfaction of Engineer-in-charge. |
| 4 | providing and fixing of factory manufactured precast concrete kerb of size 300mm x 300mm having 150mm thickness with one edge semi rounded duly vibrated mechanically and compacted made of P.C.C 1:2:4 duly cured and finished. The rate further include filling of joints between kerbs / channels with cement mortar 1:2 complete in all respect and to the entire satisfaction of Engineer-in-charge |
| 5 | providing and fixing of factory manufactured precast concrete channel of size 300mm x 300mm having 75mm thickness duly vibrated mechanically and compacted made of P.C.C 1:2:4 duly cured and finished. The rate further include filling of joints between kerbs / channels with cement mortar 1:2 complete in all respect and to the entire satisfaction of Engineer-in-charge. |
| 6 | Providing and applying 2.5mm (minimum) thick thermoplastic road marking paint for edge line, central line, stop line, segregation line, zebra crossing, all signs on road etc. The thermoplastic material should be homogeneously composed of pigment, hot resin and glass reflectorising beads @0.250 Kg/Sqm. The gradation of glass beads must be as per table 800.4 and properties of material should be as per table 800.3 of MORT&H specification (5th revision). The work should be complete as per MORT&H specification clause 803.4 complete in all respects and to the entire satisfaction of Engineer-in-charge. N.S. |
| 7 | Providing and applying 5mm (minimum) thick thermoplastic road marking paint for edge line, central line, stop line, segregation line, zebra crossing, arrows and other road signs etc. The thermoplastic material should be homogeneously composed of pigment, hot resin and glass reflectorising beads @0.250 Kg/Sqm. The gradation of glass beads must be as per table 800.4 and properties of material should be as per table 800.3 of MORT&H specification (5th revision). The work should be complete in all respects and to the entire satisfaction of Engineer-in-charge. (Yellow line Rumble Strips) |
| 8 | Providing and applying 15mm (minimum) thick thermoplastic road marking paint for edge line, central line, stop line, segregation line, zebra crossing, arrows and other road signs etc. The thermoplastic material should be homogeneously composed of pigment, hot resin and glass reflectorising beads @0.250 Kg/Sqm. The gradation of glass beads must be as per table 800.4 and properties of material should be as per table 800.3 of MORT&H specification (5th revision). The work should be complete in all respects and to the entire satisfaction of Engineer-in-charge.(Yellow line Rumble Strips) |
| 9 | Providing and fixing of Raised pavement markers (Cat eyes) of make 3m series/ Avery Denninson 80/C-80 conforming to ASTM D4280 type H with micro prismatic lens on both sides with 13 sq cum retro-reflective surface area in each lens, having two no. 3cm shanks and fixing the same with suitable epoxy after cutting the road surface for embedding shanks complete in all respects and to the entire satisfaction of the Engineer in charge. N.S. |
| 10 | Manufacturing ,supplying and fixing retro reflective regulatory sign board consisting of 600 mm Dia circular sign boards and definition plate of Size 600x230mm made up of 3mm thick ACP sheet,rivted with 25x25x3mm MS angle iron frame, face to be fully covered with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in required color combination including subject matter, message ,symbols and borders etc. screen printing with transparent ink as per IRC ; 67:latest edition, on main and definition plate and fixing the same on 3660mm high vertical post of M.S. angles of size 50x50x5 mm welded with hold fast of same size 225mm long at the bottom end to be embedded in ground with cement concrete 1:2:4 block of size 225x225x300mm after making pit in ground. The rate further includes painting white and black color alternate bands of 300mm long over one coat of priming coat to vertical post and steel work to be painted with two or more coats of synthetic enamel paint of required shade and of approved brand & manufacture over priming coat, complete in all respects and to be entire specification of Engineer-in -charge. N.S. |
| 11 | P/F of Cautionary board of equilateral triangle of size 900 x 900 x 900 mm, along with indication plate of size 600 x 300 mm made of 3mm thick ACP Sheet. Front side to have type IV Retro Reflective High Intensity Microprismatic sheeting confirming IRC- 67-latest edition/ASTM - D-4956 subject matter on the base with screen printing of transparent ink for sign and lettering in different colour. The back support frame consisting of MS angle 25x25x3mm, provided with one leg post of height 3.66 meter of 50x50x5mm MS angle and hold fast of same size at 150mm from bottom painted with first quality synthetic enamel paint with primer of alternate colour Black & White and embedding the same in C.C. 1:2:4 block of size 225x225x300mm rates also include digging of pit complete in all respect and to the entire satisfaction of Engineer-in-Charge. N.S. |
| 12 | Providing and fixing of Speed limit board of Size 1620 x 920mm made out of 3mm thick ACP Sheet fabricated with frame of M.S. rectangular pipe of 75 x 40 mm (3mm thick) having three numbers pipe In horizontal and two pipes in vertical position. The ACP sheet shall be fixed with aluminum alloy sheet rivets at suitable intervals on both sides of frame. The front side of board shall have retro reflective micro prismatic sheet type IV (HIP) text and matter should be screen printing with transparent ink as per irc standard. For the support of frame the two nos. M.S. rectangular pipe 75 x 40mm having 2100mm clear height from ground to the bottom of board and 600mm in ground with enchorage of M.S. Angle 50x50x5mm, 9\\" long to be embedded in C.C.1:2:4 Block of size 45x45x45cm including painting of two or more coats of synthetic enamel paint including priming coat and preparation of surface rates also inclued the digging of pit of same size complete in all respect and to the entire satisfaction of Engineer-in-charge. N.S. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysOct 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender