Tender For Addition/Alteration And Special Repair Of Married Accn At Makarpura At Vadodara Military Station Under Ge (Army) Baroda
Tender Value
3.80 Crore
Estimated cost
Bid Submission
04 Nov 2026
23 days left
EMD
4.55 Lakhs
Bank guarantee accepted
Document Fee
2000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Vadodara → Gujarat
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Addition/Alteration And Special Repair Of Married Accn At Makarpura At Vadodara Military Station Under Ge (Army) Baroda
BOQ
| Sl. No. | Item Description |
| 1 | Note: (i) Please refer schedule 'A' notes before quoting the tender. (ii) Amount of Schedule of credit shall be deducted off line by the department. |
| 2 | Demolition of stone slabs and tiles of any description or thickness in floors & wall, laid bedded & pointed in any mortar complete all as specified and directed. |
| 3 | Demolition of cement concrete (unreinforced) in ground floor and pavings n.exc.15 cm thickness (below or above ground level) and removing from site all as specified and directed. |
| 4 | M & L for 25 mm thick cement concrete in flooring type B0, 1:2:4 (12.5mm graded aggregate) with liquid water proofing compound as per manufacturers instructions as in subbase or for laying floor tiles complete all as specified and directed. Note (WPC will be measured and paid separately). |
| 5 | Roughening of old unservicable PCC floor surface by picking, chipping and wire brush sweeping clean and washing down with water to remove dust outside to make it suitable for laying floor tile complete all as specified. |
| 6 | M&L for non skid coloured ceramic tile 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38sqm , as in floors etc set over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:4 including necessary adhesive complete all as specified and directed. (Tile pattern and decoration as approved by Engineer-in-charge) |
| 7 | M&L for non skid colour ceramic tile 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38sqm , as in skirting etc set over and including 10 mm thick rendering with CM 1:3 including necessary adhesive complete all as specified and directed. (Tile pattern and decoration as approved by Engineer-in-charge) |
| 8 | M&L for non skid coloured ceramic tile 7 to 8 mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18sqm , as in floors etc set over and including screed bed or bedding layer of mortar 15 mm thick for laying floor finishes with CM 1:4 including necessary adhesive complete all as specified and directed. (Tile pattern and decoration as approved by Engineer-in-charge) |
| 9 | M & L for Glazed ceramic coloured walls tiles in vertical surfaces 300x450x 6mm to 7 mm thick set over and including 10 mm thick rendering on vertical surface of wall or concrete surfaces in CM 1:3 to receive wall tiles including necessary adhesive (Tile pattern and decoration as approved by Engineer-in-charge). |
| 10 | Demolition of reinforced cement concrete of any description and any position not otherwise specifically provided for , all as specified and directed. |
| 11 | M&L for Providing reinforced cement concrete (nominal mix) Type B1, 1:2:4 (using 20 mm Aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like including necessary form work complete all as specified and directed. Note. (reinforcement shall be measured and paid separately) |
| 12 | M& L Formwork flat to sides and soffits of floor or roof beams, beam haunch ings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc complete all as specified and directed. |
| 13 | Taking down chowkats or frame with shutter (without taking off shutter from the frame) n.exc 1.5sqm each complete all as specified and directed. |
| 14 | Taking down chowkats or frame with shutter (without taking off shutter from the frame) Exc 1.5 Sq m but n.exc 4.00 Sq m each complete all as specified and directed. |
| 15 | M & L for 18 to 20 mm thick machine cut green marbel stone in single piece in window/opening (Jambs/Cills), steps threads, raiser and equivalent laid over cement screed and jointed with base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 10 mm thick plastering with cement mortar 1 : 3 including necessary adhesive complete all as specified |
| 16 | M&L Granite (of any type and colour) work (table rubbed and polished) 18 to 20mm thick in cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match complete all as specified and directed. |
| 17 | M & L for machine cut kota stone slab flooring in landings of staircase & treads of steps etc. of 20 - 25mm thick (the stone may be in one piece) including rubbing and polishing and to engraved to horzontal lines each step anti skid complete set over and including screed bed or bedding layer of mortar 20 mm thick for laying floor finishes with CM 1:4 complete all as specified and directed. |
| 18 | M & L for machine cut kota stone slab 12 - 15mm thick on vertcle sufaces steps, skirting , and dado of over 10 mm thick plaster in cement mortar in 1:4 jonted with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed. |
| 19 | Rounding to edges of stone slabs such as steps cooking platform and other similar situations complete all as specified. |
| 20 | S&F 40mm Flush shutters, solid core construction, with block board core both faces are covered with decorative face veneer with lipping/frame to match, complete all as specified and as directed |
| 21 | S & F 35mm thick 2nd class Hard wood Glazed and Skelton shutters, open rebated and prepared to receive glass, gauze etc squares with sash bar of framing plain, chamfered or rounded, fitted with cut ,mitered and moulded beads for securing glass etc, sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and as directed |
| 22 | M & L for preparing new wooden surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer.complete all as specified . |
| 23 | S&F steel helical door spring 300mm ordinary rat tail rod pattern springs including roller plate complete all as specified and directed. |
| 24 | S&F of Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified |
| 25 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of sliding windows & ventilators including providing and fixing hinges/ pivots/roller and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (All fittings i.e rollers,locking,Al ventilator louvers arrangement with nobe incl in rates ) with extruded built up standard tubularsections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 26 | S&F 4.00mm thick sheet glass, selected ordinary quality and glazing with rubber beading or with glazing clips exc 0.5 sq. m in each pane including solar control film 25 micron reflective type sticked to glass panes as per instructions of manufacturers, all as specified and directed. |
| 27 | S&F 4.00mm thick figured glass, pin head type and glazing with rubber beading or with glazing clips n exc 0.5, all as specified and directed. |
| 28 | S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified. |
| 29 | M & L in repair for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework (caging) of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 30 | S&F Pressed steel frames size (165x60)mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed. |
| 31 | S&F Pressed steel frames size (105x60)mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.,complete all as specified and directed. |
| 32 | M&L cement concreteType B1 1:2:4 (20 mm graded aggregate) in hold fast and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and directed. |
| 33 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/Chowkhat of size 50 x 100 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. all as specified and directed. |
| 34 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary SS screws shall be paid separately). |
| 35 | S&F 18mm thick HDHMR BOARD exterior grade including any coloured prelaminated sheet of required thickness over HDHMR board, anti fungal, moisture resistance, anti borer as per IS 14587 for frame and shutter for kitchen cabinets/cupboards etc all as per specified and directed by Engr-in-charge. Note: sample as approved by GE. |
| 36 | S&F for Framed work as in doors, windows or gates or grill/grating of angle or other section with gusset plates, rails, braces, etc., complete, drolled for fixing of steel sheeting or other covering. Doors/Windows, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting (exclusive of steel sheeting or other covering, running rails and guides) and hanging: also fastening and fixing complete all as specified and directed. |
| 37 | S& fixing 75 mm long butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified and directed. |
| 38 | S & F 150 mm Aluminium handles, febricated type anodised or fixing to door/cupboard/kitchen cabinet etc,complete all as specified and as directed. |
| 39 | S & F 100 mm Aluminium handles, febricated type anodised or fixing wardrobe cupboard/kitchen cabinet etc,complete all as specified and as directed. |
| 40 | S&F magnetic catch size (70x20x15)mm including fixed with screw complete all as specified |
| 41 | S & F 150 mm long aluminium anodised barrel tower bolt fixed to wiremesh door and equivalent all as specified. |
| 42 | S&F of 300 mm long aluminium anodised sliding door bolt with hasp and staple and fixing clips of sheets, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed. |
| 43 | S & F aluminium anodised Hasp and staple, safety type of size 75 mm with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed. |
| 44 | S&F floor door stopper of stainless steel and tongue, overall length of cover plate 140mm anodised with hard drawn steel spring, fixed in floors complete all as specified and directed. |
| 45 | S&F in 25mm dia stainless steel tubular curtain rod and fency type socket fixing with brackets, stop, roller etcincl taking down old complete all as specified and directed.Note: design of socket shall be approved by GE/AGE at the time of execution) |
| 46 | S & F 20 mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed |
| 47 | M$L cutting chases brick wall , pinning ,in making good to facing where required in C M 1:3 and pointing or edes of landings, steps , cill sunshed shelves linte cutting chases for concealed water tubingls etc and making good cutting exeeding 20 cm girth complete all as specified and directed. |
| 48 | Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal out side MOD land all as directed by Engr-in-Charge. |
| 49 | S & F 25 mm outer dia CPVC pipes SDR 11 & plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed |
| 50 | Dismantling of 100mm cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches/wall, if required complete all as specified and directed. |
| 51 | Dismantling of 75mm cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches/wall, if required complete all as specified and directed. |
| 52 | S & F 110mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall/trenches all as specified and as directed. |
| 53 | S & F 110mm bore PVC (SWR) bends any radius all as specified and as directed. |
| 54 | S & F in 75mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall /trenches all as specified and as directed. |
| 55 | S & F 75mm bore PVC (SWR) bends any radius all as specified and as directed. |
| 56 | S & F 75mm bore PVC (SWR) bends any radius with oval access doors all as specified and as directed. |
| 57 | S & F 75mm PVC (SWR) floor trap, plain with CP grating including jointing with solvent all as specified and as directed. |
| 58 | S & F in 110mm bore PVC (SWR) branch piece, single (single Y) equal or unequal or with parallel branches with access door all as specified and as directed |
| 59 | S & F in repairs 75mm bore PVC (SWR) branch piece, single (single Y) equal or unequal or with parallel branches with access door all as specified and as directed |
| 60 | S & F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays incliding bolts and nuts and securing ends of stays to walls and roofs for 110mm bore pipe all as specified and as directed |
| 61 | S & F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays incliding bolts and nuts and securing ends of stays to walls and roofs for 75mm bore pipe all as specified and as directed |
| 62 | S & F 110mm PVC (SWR) vent cowl all as specified and as directed |
| 63 | S & F 75mm PVC (SWR) vent cowl all as specified and as directed |
| 64 | S & F 110mm PVC (SWR) WC connector with lip ring all as specified and as directed. |
| 65 | S & F 110mm PVC (SWR) WC connector bent type to fit WC outlet all as specified and as directed. |
| 66 | S & F 110mm PVC (SWR) junction single, (Single T type) equal or unequal all as specified and as directed. |
| 67 | S & F 75mm PVC (SWR) junction single, (Single type T) equal or unequal all as specified and as directed. |
| 68 | S & F CP wall mixer three in one system for mixing hot and cold water screwed down for iron pipe 15 mm bore and fixed complete all as specified and directed. |
| 69 | S & F IN REPAIR CP stop valves/Angle valve15mm bore fancy type chromium plated screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 70 | S & F 25mm dia bore gun-metal, globe or gate valves with iron wheel head screwed both ends for iron pipe complete all as specified and directed. |
| 71 | S & F 125mm dia chromium plated shower rose with swivel joints including fixing to steel pipe or GI union complete all as specified and directed. |
| 72 | S&F 32 mm bore low density polyethylene pipe (LDPE) of pressure rating 6 Kgf/cm2 as in waste pipe complete all as specified and directed. |
| 73 | Dismantling of water storage tank of 500 ltrs capacity complete all as specified and directed. |
| 74 | S&F 500 ltrs rotational moulded polythene White colour water storage water tanks twin layered construction ( cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I duly ISI Marked, complete all as specified. |
| 75 | S & F Ball brass valves, for 25 mm bore of pipe high pressure, with polythene float and fly- nut complate, screwed for iron pipe or brass ferrule complete all as specified and directed. |
| 76 | S&F in repair Vitreous China, semi-pedestal pattern (Anglo-Indian Type), white (excluding fixing bolts, flushing cistern and flush pipe) squatting pan including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. complete including making good to floor. complete all as specified and as directed. |
| 77 | S&F in repairs Plastic water closet seat cover, black, closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device complete all as specified and directed. |
| 78 | S&F IN REPAIR PVC flushing cistren low level, 10 ltr capacity with syphonic action type ball valve. Incl inlet ball valve, PVC band (flush pipe) 32mm complete all as specified. |
| 79 | S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 80 | S&F in repair vitreous china WHB white flat back size 500x400mm including Supplied and fixed angle iron brackets,CP waste coupling, 32mm dia complete all as specified & directed. |
| 81 | S&F vitreous china WHB white size 405x325 x145mm including Supplied and fixed angle iron brackets, CP waste coupling, 32mm dia complete all as specified & directed. |
| 82 | . S&F 15mm bore central hole wash hand basin brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed complete all as specified and directed. |
| 83 | S&F PVC connections 15mm size with PTMT nuts of length 450 mm complete all as pecified and as directed |
| 84 | S&F PVC connections 15mm size with PTMT nuts of length 600 mm complete all as pecified and as directed |
| 85 | S&F 350x450mm size cabinet mirror rectangular shape with 4mm thick selected quality mirror and PTMT frame with openable door shutter with PTMT frame outside mirror as complete all as specified and directed. |
| 86 | S&F CP soap dish fixed to wall with brass chromium plated screws complete all as specified and directed. |
| 87 | S&F glass shelf with chromium plated guard complete all as specified and directed. |
| 88 | S & F 20mm dia stainless steel 600mm long chromium plated tubular towel rail complete all as specified.. |
| 89 | S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever bracket and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm complete all as specified. |
| 90 | S&F stainless steel wall mounted plate rack of size 900x750X 20 mm and thickness of sheet not less than 0.60mm with provn for keeping plates and other crockery fixed with screw and rawal plug etc on wall complete all as specified and as directed |
| 91 | S& F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and as directed. |
| 92 | S&F grating 150mmx150mm made out of stainless steel complete all as specified and directed. |
| 93 | M&L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius Old size bricks in cement mortarbuilt in CM 1:6 Complete all as specified. |
| 94 | Taking down cement plaster on brick/concrete surface including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed. |
| 95 | Chipping off existing loose, damaged Concrete from RCC members of all affected RCC Columns, Beams, Slabs and Chajjas on External and internal facades, etc beyond main r/f , carefully with chised with chisel and hammer. Providing and applying. Rust passivator (Approved by GE) including wire brushing of reinforcement, cleaning washing of concrete etc complete all as direted. Providing and applying two coats of rust preventor slurry made out of \\"Polyalk Fixoprime\\" or equivalent as specified in the Brand Names and cement in Prproportiion 1:1:5 to existing r/f. bars as directed complete. Providing and applying bonding coat of slurry made out of \\"polyalk EP\\" or equivalent as specified in the Brand Names and cement in proportioon1:1 to concrete and r/f substrates complete as directed Providing and applying \\"Polyalk EP\\" or equivalent as (specified in the Brand Names. \\"Polymer modified cement mortar in Required proportions (1:5:15) to RCC members including Hand packing. curing and making the surface rough for plastering complete all as specified and directed. |
| 96 | M & L Rendering 10 mm thick on fair faces of brick work or concrete surfaces of wall in cement mortar 1:6 for finished even and smooth (without using extra cement) complete all as specified and directed. |
| 97 | M&L rendering 15mm thick on fair faces of brick work or concrete surfaces with CM (1:4) finished even and smooth by adding water proofing compound @ 3% by weight of cement without using extra cement, complete all as specified and directed.(Note: WPC item paid seperatly ) |
| 98 | M&L Rendering 5 mm thick on fair faces of brick work or concrete sur-faces of ceiling in cement mortar 1:3 for finished even and smooth (without using extra cement) complete all as specified and directed. |
| 99 | M & L for complete removal of existing treatement of walls by dust proof wall sanding machine/building walls grinding cleaning machine complete all as specified. |
| 100 | M & L for complete removal of existing treatement of ceiling by dust proof sanding machine/buildingrinding cleaning machinecomplete all as specified |
| 101 | M&L for Preparing new plaster surface applying a layer of 1 mm wall care puty on wall and two coat of distemper oil emulsion over a coat of primer on internal walls complete all as specified. |
| 102 | M&L for Preparing new plaster surface of wall applying three coat of white wash on wall complete all as specified. |
| 103 | M & L prepration of surface on wall and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces complete all as specified. |
| 104 | M&L for Preparing new plaster surface apply three coat of white wash on ceiling complete all as specified. |
| 105 | M & L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specifed and as directed. |
| 106 | Demolition of cement concrete(unreinforced) of any description and in any position not otherwise specifically provided for roof complete all as specified and directed. |
| 107 | M&L for 40 mm avg thick PCC padding in cement concrete type B0 (1:2:4) using 12.5 mm graded stone aggr mixed with WPC @ 2% by wt of cement finished surface even and smooth without using extra cement for laying of WPT all as specified and directed. (WPC will be measured and paid separately). |
| 108 | M&L 10mm thick rendering on roof in CM 1:3 mixed with WPC as per manufacturer's instructions of cement for finished even and smooth without using extra cement over PCC surface for laying APP membrane on roof complete all as specified and directed. (WPC will be measured and paid separately). |
| 109 | M&L for water Proofing treatment to roof slabs by applying one coat of bituminious/polymerized primer confirming to IS-3384 @ 0.40 Ltrs/Sqm, 3 mm thick APP modified polymeric membrane of weight of 3 kg/sqm with non-woven polyester reinforcement shall be laid over a coat of bitumen S-35 grade (30/40) applied @1.20Kg /Sqm (minimum) with minimum 75 mm side overlaps and minimum 100 mm end overlaps, joints & overlaps shall be sealed by torch application and applying one coat of aluminium paint @ 0.11 Kg/Sqm over APP membrane complete all as specified and directed by Engr-In-Charge (Note: the primer and the membrane to be used shall be of the same manufacturer and to be applied by authorized applicator of OEM). |
| 110 | S&F Hard drawn steel wire fabric not exc 4 kg /sqm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed with angle iron complete all as specified and as direted |
| 111 | M & L for preparing new steel surface of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide prime complete all as specified . |
| 112 | Demolition of cement concrete (unreinforced) in ground floor and pavings exc.15 cm thickness (above ground level) and removing from site all as specified and directed. |
| 113 | M&L for 15 mm thick plaster in sunken portion with CM 1:3 mixed with liquid water proofing compound as per manufacturers instruction and should be even and smooth without using extra cement complete all as specified and directed.. Note . (WPC will be measured and paid separately). |
| 114 | M&L for providing & laying applying one coat of bituminious/polymerized primer confirming to IS-3384 @ 0.40 Ltrs/Sqm, 3 mm thick APP modified polymeric membrane of weight of 3 kg/sqm with non-woven polyester reinforcement shall be laid over a coat of bitumen S-35 grade (30/40) applied @1.20Kg /Sqm (minimum) with minimum 75 mm side overlaps and minimum 100 mm end overlaps, joints & overlaps shall be sealed as per manufacturer instructions complete all as specified and as directed. |
| 115 | M&L for sunken portion filled with lean concrete 1:5:10 using brick/lime aggregate and finish the surfaces rough to receive sub base complete all as specified and as directed. |
| 116 | Supply only Internal water proofing compound (Liquid type) all as specified and directed. |
| 117 | M&L Cement concrete type B0 1:2:4 (12.50 mm graded aggregate) as in Coping, rounded or chamfered on edgescomplete all as specified and as directed. |
| 118 | S & F 15mm bore chromium plated fancy type bib tap long body with nosel suitable for washing machine, screwed down, high pressure for iron pipe or for brass ferrule complete all as specified and directed. |
| 119 | S & F 15mm bore chromium plated fancy type bib tap long body, screwed down, high pressure for iron pipe or for brass ferrule complete all as specified and directed. |
| 120 | S& F 200 MM long mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed compllet all as specified |
| 121 | S& F 100 MM long butt hinges, heavy weight, cold rolled mild steel, and fixed complete all as specified |
| 122 | M&LWriting letters or figures (Block. Roman, Italic or Indian) n exc. 30 cm high complete all as specified. |
| 123 | S& F20 mm outer dia bore Brass Tee complete all as specified and directed. |
| 124 | S & F 20 mm outer dia Male Brass Threaded Adaptor(MTA/ MBTA) complete all as specified and directed. |
| 125 | S &F 20mm outer dia Female Brass Threaded Adaptor (FTA/ FBTA) complete all as specified and directed. |
| 126 | S& F Brass Elbow 20mm outter dia complete all as specified and directed. |
| 127 | S& F25 mm outer dia bore Brass Tee complete all as specified and directed. |
| 128 | S &F 25mm outer dia Female Brass Threaded Adaptor (FTA/ FBTA complete all as specified and directed. |
| 129 | Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in soft loose soil, all as specified. |
| 130 | M&L Roof trusses Fe 410-W (Gde E-250 )quality A (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed. |
| 131 | M&L for Pre-painted galvaiume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screwscomplete all as specified and directed. |
| 132 | M& L for Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping scre complete all as specified and directed. |
| 133 | M&L Hardcore of gauge n exc. 63 mm,( stone aggregate) deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed |
| 134 | M&L for Cement concrete type D2 (1:4:8) (40 mm graded aggregate) in foundations, filling and mass concrete complete all as specified and directed. |
| 135 | M&L for 75mm thick plain cement concrete type D-2, 1:4:8 using 40mm graded stone aggregate as in floor complete all as specified directed. |
| 136 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc., of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand complete all as specified and directed. |
| 137 | M & L for 75 mm thick PCC 1:3:6 mix type C2 using 40mm graded stone aggregate as in paving finishing cone surface (plinth protection) even and smooth without using extra cement complete all as specified and directed. |
| 138 | Taking down copper/aluminium point wiring (light fan, socket or power) complete including fittings such as switch, sockets, c/rose, lamp holders, tube light fittings, sketch fitting , wooden boards, bell push, call bell, MCBs & regulators etc & making good to disturbed surfaces & matching with the existing colour of wall floor etc complete all as specified and directed. |
| 139 | Taking down main switch, DB/change over/VTPN, MCCB AC box of any capacity complete all as specified and directed. |
| 140 | M&L for taking down carefully sub main wiring including batten any type of conduit by unscrewing from floor,wall,ceiling and making good surfaces to match with original status for all types of sub main wiring complete all as specified and directed. |
| 141 | M & L for concealed point wiring complete with multistranded copper conductor (FRLS)1.5 Sqmm size PVC insulated unsheathed cable 1100 volt grade, conforming IS 694 & color code in conduit system of wiring, drawn in including PVC conduit not less than 20 mm dia concealed duly fixed with U-Clips, including cutting chases, finising of slote by means of cement mortor making good to the existing surface of the wall & touching with the existing colour of wall with three coats and making good disturbed surface complete, sunk in pressed Modular Metal flush box of required size not less than 2 mm thick GI Plate factory made with modular cover plate, screw with all accessories including single core multistranded copper conductor 1.5 sqmm size solid PVC insulated unsheathed cable (FRLS) as earth wire to common earth and connected to earth dolly drawn in same conduit complete all as specified. |
| 142 | For one light, fan point controlled by one switch |
| 143 | For call bell point controlled by one switch |
| 144 | For one 5 Amp independent socket point controlled by one switch |
| 145 | For one 3 pin ,5 Amp socket point with other switch on the same board |
| 146 | For one light, point controlled by two way switch |
| 147 | All as per item No 141 here in before but for power point wiring using with 2.5 sqmm PVC-FR LS insulated ,sheathed, copper conductor stranded 1100 volt grade cable and 2.5 sqmm PVC insulated ,sheathed, copper conductor stranded 1100 volt grade cable as continuous earth lead complete all as specified and directed by engir in charge. |
| 148 | All as per item No 141 here in before but for power point wiring using with 4 sqmm PVC-FR LS insulated ,sheathed, copper conductor stranded 1100 volt grade cable and 4 sqmm PVC insulated ,sheathed, copper conductor stranded 1100 volt grade cable as continuous earth lead complete all as specified and directed by engir in charge. |
| 149 | S&F Modular switch 1 way 6A, 1module complete all as specified and directed. |
| 150 | S&F Modular switch 2 way 6A, 1module complete all as specified and directed. |
| 151 | S&F Modular call bell switch 1 way 6A, 1module complete all as specified and directed. |
| 152 | S&F Modular Socket, 6A - 2/3 pin combined 2module complete all as specified and directed. |
| 153 | S&F Modular switch 1 way 16A, 1module complete all as specified and directed. |
| 154 | S&F Modular Socket, 16A - 3/5 pin combined 2module complete all as specified and directed. |
| 155 | S&F Modular Fan step regulator, 120W - 2 module complete all as specified and directed. |
| 156 | S & F ceiling rose surface polycarbonate body three terminal complete all as specified and directed. |
| 157 | S & F Lamp holder, PVC type with back plate suitable for batten fittings including LED lamp 9 Watt complete all as specified and directed. |
| 158 | S&F modular AC Box with 20 Amps 230 Volts MCB SP, metal enclosure & Unbreakable heavy duty with ISI marked plug top complete all as specified and directed. |
| 159 | S & F of ceiling fan operated with blades, anti suicide rod from existing roof / trus to fall ceiling, electronic regulator operated and accessories, 230V, 35 Watts, 1200mm sweep. Min air delivery 210 CFM with service value 6.00 BEE, five star rated with brushless direct current motor including ceiling fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose and taking down existing UNSV ceiling fan complete all as specified and directed.Note : 1) Old ceiling fans shall be deposited to AGE E/M store yard for re issue to other buildings after repair/servicing or suryed off as per procedure in vogue etc. |
| 160 | S & F of LED light fitting 20 Watts (4 Feet), 220 Volts AC, Aluminium extrusion , input 140-270 Volts AC, CCT 6000K, luminus efficiancy 120 lumens/watt, surge protection upto 4KV volage protection upto 440V, AC, PF >0.9 and including LED light fitting connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 161 | S & F of LED light fitting 10 Watts (2 Feet), 220 Volts AC Aluminium extrusion , input 140-270 Volts AC, CCT 6000K, luminus efficiancy 100 lumens/watt, surge protection upto 4KV volage protection upto 440V, AC, PF >0.9 and including LED light fitting connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and directed. |
| 162 | S & F of exhaust fan made of sturdy engineering steel body complete with louvers shutter & mosquito net, voltage 230V, 50Hz, RPM 1200, copper winding of sweep 300mm including exhaust fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose including make hole in stone/brick wall grouting & making food in all aspects and taking down existing UNSV exhaust fan complete all as specified and directed.Note : 1) Old exhaust fans shall be deposited to AGE E/M store yard for re issue to other buildings after repair/servicing or suryed off as per procedure in vogue etc. |
| 163 | S & F of exhaust fan made of sturdy engineering plastic body complete with louvers shutter & mosquito net, voltage 230V, 50Hz, RPM 1200, copper winding of sweep 250 mm including exhaust fan connecting up with three core flexible copper conductor cable of suitable size from ceiling rose including make hole in stone/brick wall grouting & making food in all aspects and taking down existing UNSV exhaust fan complete all as specified and directed.Note : 1) Old exhaust fans shall be deposited to AGE E/M store yard for re issue to other buildings after repair/servicing or suryed off as per procedure in vogue etc. |
| 164 | M&L concealed Sub main wiring with FRLS two single core PVC insulated and unsheathed fire retardant multi stranded copper conductor cable 1100 volt grade IS-694, marked of 6.0 Sqmm size drawn through and including not less than 20 mm dia PVC conduit medium grade ISI marked and conduit junction boxes, terminal boxes and accessories such as tees, bends, elbows, reducers, bell mouth tube ends fixed to the surface of wall/ceiling including one run of 6.0 sqmm PVC insulated and unsheathed FRLS multi stranded copper conductor cable for earth wire continuity conductor complete all as specified and directed.NOTE : Two runs of single core 6.0 sqmm and one run of 6.0 sqmm copper FRLS cable as earth continuity conductor and suitable size conduit with accessories shall be measured as one length. |
| 165 | M&L concealed Sub main wiring with FRLS two single core PVC insulated and unsheathed fire retardant multi stranded copper conductor cable 1100 volt grade IS-694, marked of 10.0 Sqmm size drawn through and including not less than 20 mm dia PVC conduit medium grade ISI marked and conduit junction boxes, terminal boxes and accessories such as tees, bends, elbows, reducers, bell mouth tube ends fixed to the surface of wall/ceiling including one run of 6.0 sqmm PVC insulated and unsheathed FRLS multi stranded copper conductor cable for earth wire continuity conductor complete all as specified and directed.NOTE : Two runs of single core 10.0 sqmm and one run of 6.0 sqmm copper FRLS cable as earth continuity conductor and suitable size conduit with accessories shall be measured as one length. |
| 166 | S&F sheet metal enclosure for DB double door SPN 8 Ways, IP-43 240 V with 200 Amps rated bus bar including taking down complete all as specified and directed. Note :- Cutting and chasing in stone/Brick masonary and making good to disturbed surfaces will be including in item rate . |
| 167 | S&F sheet metal enclosure for DB double door SPN 12 Ways, IP-43 240 V with 200 Amps rated bus bar including taking down complete all as specified and directed. Note :- Cutting and chasing in stone/Brick masonary and making good to disturbed surfaces will be including in item rate . |
| 168 | S&F sheet metal enclosure for DB double door TPN 04 Ways, IP-43 240 V with 200 Amps rated bus bar including taking down complete all as specified and directed. Note :- Cutting and chasing in stone/Brick masonary and making good to disturbed surfaces will be including in item rate . |
| 169 | S&F testing and commissioning of MCB TPN 240 volt 63 Amp 10 KA capacity having C-curve characteristics connected with suitable lugs including taking down complete all as specified and directed. |
| 170 | S&F testing and commissioning of MCB SPN 240 volt 16 Amp to 40 Amp 10 KA capacity having C-curve characteristics connected with suitable lugs including taking down complete all as specified and directed. |
| 171 | S&F testing and commissioning of MCB SP 6 Amp to 40 Amp 240 Volt 10 KA capacity having C-curve characteristics connected with suitable lugs. All as specified and directed by Engr in charge. |
| 172 | S & F in replacement Bell ding dong type, one way, 240 volts, AC, ISI marked complete all as specified and directed. |
| 173 | M & L for fabrication of sheet metal board of size 60x50x20 CM made of 2mm thick MS Sheet with locking arrangement dully two coat of synthetic enamelled paint over one coat of red oxide. All as specified and directed by Engr in charge. Note :- Cutting and chasing in stone/Brick masonary and making good to disturbed surfaces will be including in item rate . |
| 174 | S & F of LED bldg security light fitting 30 Watt input voltage 140-270V AC outdoor type with high robust die cast body aluminium housing CCT 6500K lumeinous efficincy > 120 lumens/watts CRI > 70, PF >0.95 protection class IEC safety class-I and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection including bracket made out of GI pipe light grade 32mm bore not less than 1.20m long bent to shape required fixed to pole with suitable size 2 Nos clamps made out of 25X3mm flat iron with nut, bolts and washers complete including old U/S taking down complete all as specified and directed.Note :- The warranty on light should be of minnimum 2 Years . |
| 175 | Taking down existing geyser of any capacity, kept in safe condition and refixing after completion of new wiring at same location with mew fastener as per direction of Engr-in-Charge. |
| 176 | Taking down existing energy meter, kept in safe condition and refixing after completion of new wiring at same location as per direction of Engr-in-Charge. |
| 177 | Earthing Complete with galvanised steel earth plate electrode 60cmx60cmx6mm thick burried directly in ground vertically to a depth not less than 2.5 metre below ground level with top edge of the earth plate at a depth not less than 1.5 mtr below ground level earth plate surrounded from all sides by 15cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connection by using galvanised earth lead wire 4.0mm dia as earthing lead by means of bolts, nuts, check nuts and washers made of galvanised iron and thimbles and other end of the earth wire connected to main switch board protected by galvanised iron medium grade pipe 40mm bore in wall/floor/and GI Pipe 20 mm bore light grade for watering with funnel and wire mesh PCC chamber in cement concrete 1:3:6 type C-2 and RCC pit cover including necessary excavation and earth work in any type of soil, returning slurry approved soil and disposed of surplus soil to a distance not exceeding 50 Mtr away all as shown in electrical plate No 3 of SSR 2009 ( Part-I) complete all as specified and directed. |
| 178 | CONTD Notes:-(a) The unit rate shall include for GI protection pipe, GI watering pipe, wire mesh, funnel and excavation, RCC pit cover, test point, galvanised iron strip from top of earth plate upto 7.5 metres above ground level and if GI protection pipe is less than 7.5 metres, no price adjustment shall be made.(b) PCC pit shall be provided at least 50cm away from the earth pit and not just on the earth pit and extra cost of additional length of water pipes and fittings, junction, elbow etc shall be deemed to be included in the unit rate.(c) If the testing result of earthing work is not found satisfactory then the contractor shall do another earthing work at his own cost and nothing shall be permissible on this account.(d) Earthing work will be carried out in presence of MES representative. |
| 179 | Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out soft loose soil complete all as specified and directed. |
| 180 | M& L factory made kerb stone of M-25 grade cement concrete in position to the required line,level and cuvature,joint with cement mortar 1:3( 1cement: 3 coarse sand) including making joints with or without grooves(thickness of joints except sharp curve shall not tobe more than 5mm) including making drainage opening wherever required complete of design as approved by GE complete all as specified and as directed |
| 181 | Removing excavated soil to a distance exceeding 250 M not exc 500 M and depositing where directed at a level not exc. 1.5mtr above the starting point complete all as specified and directed. |
| 182 | Excavation in trenches in soft and loose soil n.exc 1.5 mtr wide and n.exc. 10 sqm on plan and 1.5 mtr depth for laying and taking out of electric power cable, for foundations etc or for shaft wells manholes, pier holes cesspits etc and getting out all as specified and directed by engineer –in-charge. Note: (i) Digging shall be carried out by manual means only.(ii) During the excavation damage of Road, Electric cable, Signal Cable should be rectified by the contractor without any extra cost. |
| 183 | Returning filling in including spreading leveling watering and well ramming in layers not exceeding 25 cm thick all as specified and directed. |
| 184 | Removing excavated material not exceeding 50 mtr away and depositing where directed at a level n. exc 1.5 mtr above the starting point complete all as specified and directed. |
| 185 | Taking up GI pipe steel tubing from trench/walls etc including all fittings for following bore of pipe complete all as specified and as directed. |
| 186 | 80 mm bore |
| 187 | 40 mm bore |
| 188 | 25 mm bore |
| 189 | 15 mm bore |
| 190 | S & F to wall/trenches GI steel tubing medium grade including all fittings such as Tees, elbow, bends etc for following bore of pipe complete all as specified : |
| 191 | 80 mm bore |
| 192 | 40 mm bore |
| 193 | 25 mm bore |
| 194 | 15 mm bore |
| 195 | Taking out Gun metal gate valve for 25mm bore of pipe complete all as specified and as directed. |
| 196 | Demolition brickwork or stone/boulder masonry built in cement mortar including all quoins, arches, pillars, etc complete all as specified and as directed. |
| 197 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out hard dense soil complete all as specified and as directed. |
| 198 | M&L for Cement concrete type C-2 (1:3:6) (40 mm graded aggregate) in surface channel and drain complete all as specified and as directed. |
| 199 | M&L Brickwork with fly ash bricks, straight or curved on plan exc 6m mean radius Old size bricks in cement mortarbuilt in CM 1:4 Complete all as specified. |
| 200 | M&L rendering 15mm thick on fair faces of brick work or concrete surfaces with CM (1:4) finished even and smooth without using extra cement with neeru finish plaster complete all as pecified and as directed. |
| 201 | M&L Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends complete all as specified and as directed |
| 202 | M&L Add or deduct for each 25 mm girth or part thereof over or under 30cm complete all as specified |
| 203 | M&L Reinforced concrete pipes 600mm dia, class NP3, laid and jointed complete with collars complete all as specified. |
| 204 | Providing, cement concrete type C1 1:3:6(20mm graded stone aggregate) , in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands,plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height,copings, kneelers, apex stones,bed plates, kerbs , water troughs and the like including weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed. |
| 205 | S&F 50 mm thck Precast reinforced (SFRC) covers with frames(medium duty) of rectangular square of equvivalent area complete all as specified |
| 206 | M&L for cement concrete type C-2, 1:3:6 using 40mm graded stone aggregate as in foundations filling and mass concrete complete all as specified. |
| 207 | S&F Mild steel angle or other sections as in posts and strusts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc ; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work confirming to Fe-290 Gde E-165 complete all as specified and as directed. |
| 208 | Supply only mild steel round bar of grade Fe-290 (Gde E-165) complete all as specified and directed. |
| 209 | Supply only MS galvalnised chain link fencing, any size or type all as specified. |
| 210 | Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified and as directed. |
| 211 | M&L for preparing new steel Surfaces of any description, over 10cm in width or girthand applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed. |
| 212 | S&F Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square n. exc 5cm and not exc exc 10cm long dia of neck 5 to 10 complete all as specified and as directed. |
| 213 | M& L 250 MM long Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 04, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 23 daysNov 06, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 25 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender