Tender For special Repair To Roads, Footpath And Allied Works At Dilkusha Offrs Enclave Under Ge (West) Lucknow.
Tender Value
96.89 Lakhs
Estimated cost
Bid Submission
03 Nov 2026
5 days left
EMD
1.70 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Lucknow → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Roads, Footpath And Allied Works At Dilkusha Offrs Enclave Under Ge (West) Lucknow.
BOQ
| Sl. No. | Item Description |
| 1 | M&L for preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc sweeping with broom and and finally fanning the cleaned surface with gunny bags to remove all loose dirt/ dust etc and applying evenly a priming / tack coat with bituminous primer using paving bitumen VG 10 @ 5Kg /10 sqm , complete all as specified and directed |
| 2 | M & L for bituminous premix asphaltic semi dense concrete, 30 mm (consolidated thickness) with 5.50 % paving bitumen VG -30 by weight of total mix rolled and compacted to required camber and gradient with automatic sensor paver and 8 to 12 tone capacity roller to a uniform smooth surface as specified and directed by Engr-In-Charge. |
| 3 | M&L for premix bitumen macadam laid / rolled and compacted to required gradient and camber (consolidated thickness 75mm or less) by using paving bitumen, any penetration @ by weight of total mix complete all as specified and directed. |
| 4 | Supply and fixing cat eyes with two way solar reflective type with 30 mm length double shank of plastic body of size 100mm x 110mm x 20mm (overall height 50 mm) and with PAMA striplens reflector and weight 164 gram fixed with special epoxy chemical as per manufactures instructions , , complete all as specified and directed |
| 5 | Supply and fixing aluminium-alloy body Solar stud with following specification :-(a) Solar panel Mono-Crystalline Solar 2.4V/0.3 Watt and having charging capacity at a very low sunlight.(b) Red colour Six Super Bright LEDs with 10000 to 18000 mcd (Millicandela) 8 mm fitted at appropriate height for clear blinking point.(c) 1.2V Ni-MH or Ni-CD rechargeable battery capacity 1300 mAh. LSD (Low Self Discharge technology) fitted inside solar stud.(d) Working time 3 to 4 days successively after the battery is fully charged.(e) Charging time for full charge One full sunny day.(f) Working temperature : 10 to 75 Degree Celcius.(g) Flash rate : 60 to 70 times per minute normally.(h) Brightness sensitive auto-switch, automatically turns on at dusk and turns off at dawn to ensure easy and safe night driving.(j) High visibility LEDs help ensure easy and and safe night driving from a distance of 1000-1100 Meters approx.(k) Solar stud should be free of maintenance and operational in all weather conditions.(i) The PCB board and solar panel should be sealed in Poly Carbonate case for extra waterproofing and high/low temperature protection. The logo of the manufacturer should be embossed on front side of the body to ensure genuinesess.Dimension/Size of the Solar Std should be 125 mmx125mmx25 mm body, with shank height 65 mm (Total height 90 mm including shank)(m) Weight of the Solar Stud should be 650 Gram approx.(n) Minimum 150 gram of a special epoxy chemical should be used per pcs to fix the stud on the road surface. |
| 6 | Providing and applying 2.5 mm thick road marking strips n exc 15 cm width with 250 gram Glass Beads(retroreflective) of specified shade/colour using hot thermoplastic material by fully/semi-automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoes heater, driven by experoenced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dier, seals, oil, grease and foreign material etc, complete as per direction and accordance with applicable specifidactions as per MoRTH specification having Titatnium -12%, Resin-19% & Intermix Glass Beads - 34 % in proportion , complete all as specified and directed |
| 7 | Providing and applying 2.5 mm thick road marking strips with 250 gram Glass Beads(retroreflective) of specified shade/colour using hot thermoplastic material by fully/semi-automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoes heater, driven by experoenced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dier, seals, oil, grease and foreign material etc, complete as per direction and accordance with applicable specifidactions as per MoRTH specification having Titatnium -12%, Resin-19% & Intermix Glass Beads - 34 % in proportion, complete all as specified and directed |
| 8 | Demolition of brickwork built in cement mortar or cement lime mortar complete all as specified and directed |
| 9 | M&L brick work with fly ash brick straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 10 | Demolition of cement concrete (unreinforced) in ground floors and pavings n. exc 15cm thick (below or above ground level) complete all as specified and directed. |
| 11 | M & L for 100 mm thick Cement concrete 1:4:8, type D-2 using 40mm graded stone aggregate as in sub base etc complete all as specified and as directed. |
| 12 | S&F for precast concrete footpath block having 40 mm thickness which is made of high performance fiber reinforced concreteof min grade M-35 confirming to IS-456:2000,shapes shall be irregular like to be oval with minimum curvature radius of 3 inches, overall size shall vary between 15” x 15” to 24”x 24” as per Engineer- In-Charge. Concrete mix shall be dense with surface voids <5%, Composite fibres >1% by weight of cement to be used. Gaps between stones to be filled with PCC (1:2:4) mix embedded with white marble chips. Paver blocks should be properly cured as per IS 456:2000, comply with BIS , ISO 9001:2015, complete all as specified and directedNote: Rate of screed bed , PCC 1:2:4 included in unit rate quoted . |
| 13 | M/L for PCC 1:2:4 Type B-1 (using 20 mm graded crushed stone agg) as in benching and coping etc complete all as specified and directed. |
| 14 | S&F 150mm dia medium grade tubes with all fittings and laid in trenches or in floors complete all as specified and directed. |
| 15 | S&F solar integrated All-In-One (AIO) LED post top Luminaire having UV stabilized polycarbonate housing with min IP65 degree of protection, suitable for 60mm dia pole top mounting , complete with high efficiency LED luminaire delivering minimum 3000 system lumens, system efficiency not less than 165 lm/W, LED wattage not exceeding 18 W (+-2%) , CRI>=70, selected CCT 3000K/4000K/6500K, programmable lightening profile of 2H/4H/6H with minimum 12Hours autonomy(dim mode), integrated LiFePO4 battery of minimum [email protected], or equivalent energy capacity complete with BMS, integrated Mono-crystalline Solar PV module of minimum 13Wo MPPT charge controller with charging efficiency not less than 90% , integrated 5.8 GHz microwave motion sensor with sensing distance upt 25m, LED life minimum 25000 burning hours(L70), suitable for operation from 0 degree Celsius to +55 degree Celsius , complete with remote programmer/controller, mounting bracket nuts, bolts and all the accessories. The Solar PV module shall conform to the latest editions of IEC 61215 and IEC61730-1 & IEC 61730-2. The luminaire shall conform to IEC 60598-1 and IEC 60598-2-3 and shall have minimum IP65 protection in accordance with IEC 60529. All components shall comply with the latest applicable BIS/IEC standards. test certificates from NABL- accredited on internationally accredited laboratories for the complete system/components shall be submitted, including fixing of pole size 60mm di, up to 3m long, GI pipe light grade, duly painted with two coats of synthetic enamel paint fixed with nuts, bolts grouting in ground including PCC 1:2:4 and all the earth work , complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysNov 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender