Tender For Special Repair To Bldg No P-214(Ck House) At Misa C Under Ge(S) Tezpur
Tender Value
28.93 Lakhs
Estimated cost
Bid Submission
27 Oct 2026
0 days left
EMD
58000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Sonitpur → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Bldg No P-214(Ck House) At Misa C Under Ge(S) Tezpur
BOQ
| Sl. No. | Item Description |
| 1 | Taking down chowkhats or frames area not exc. 1.50 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed. |
| 2 | Taking down chowkhats or frames area exc. 1.50 Sqm but not exc. 4.00 Sqm each with shutters (without taking off shutters from the frames) complete all as specified and directed. |
| 3 | Demolition of brick work built in cement mortor including all quoins, arches, pillars etc and complete all as specified and directed. |
| 4 | Demolition of reinforced cement concrete of any description and in any position (reinforcement cut as required to facilitate demolition) and removal all rubbish material complete all as specified directed. |
| 5 | Taking down cement or cement lime plaster any description on any walls etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed |
| 6 | Taking down existing roof tretment of any size comlete all as specified and directed. |
| 7 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed. |
| 8 | Taking up or down water pipe tubing and connections, including cleaning for re-fixing or removal to store Outer diameter of pipes : 20 mm complete all as specified and directed. |
| 9 | Taking up or down water pipe tubing and connections, including cleaning for re-fixing or removal to store Outer diameter of pipes :25 mm complete all as specified and directed. |
| 10 | Dismantling water tanks of capacity exec 500 l and not exec 1000 l and removing to store complete all as specified and directed. |
| 11 | Demolition and breaking up drain pipes of internal dia 100/75 mm (Salt glazed ware,AC or Reinforced concrete,CI,PVC) set in cement mortar complete all as specified and directed. |
| 12 | M&L Brickwork with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius built in Cement mortar 1:6 complete all as specified and as directed. |
| 13 | M&L for brickwork with subclass‘B’ bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and directed. |
| 14 | M&L for rendering 15 mm thick on faces of brick work or concrete surface in CM (1:6), finished even and smooth without using extra cement complete all as specified and directed. |
| 15 | M&L for 15 mm thick rendering with cement mortar (1:4) on fair faces of brick work in two layers (10mm & 5mm)seperately mixed with water proofing compound in top layer as per manufacturer's instructions and finishing the surface even and smooth without using extra cement complete all as specified and as directed.Note:- WPC shall be measured and paid seperately under appropiate item. |
| 16 | Supply only liquid water proofing compound complete all as specified and directed. |
| 17 | M&L for rendering 5 mm thick on fair faces of brick work or concrete surface in CM (1:3) as in ceiling, finished even and smooth without using extra cement complete all as specified and directed. |
| 18 | M & L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of primer over and including a coat of 1mm thick white putty complete all as specified and directed. |
| 19 | M & L for complete removal of existing treatment and applying two coats of oil bound distemper over a coat of primer over and including a coat of 1mm thick white putty complete all as specified and directed. |
| 20 | M&L for finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) over a coat of 1 mm thick wall care putty suitable for exterior emulsion paint Allow 6-8 hrs to dry the surface in both the coats of paint complete all as specified and directed. |
| 21 | M&L for finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) over a coat of 1 mm thick wall care putty suitable for exterior emulsion paint Allow 6-8 hrs to dry the surface in both the coats of paint including complete removal of existing treatment on wall/ roof projections including facia,cornices etc by scrapping to make surface clean,free from dust,loose paint etc by skilled labour complete all as specified and directed. |
| 22 | S & F 125mmx60mm size and 1.60 mm thick pressed steel frames for doors with one or more rebates incl necessary fixing lugs, hinges, lock strike plate etc including applying a coat of tar in inner surface ,red oxide to outer surface and filling the frame using PCC M-10 using 12.50 mm graded stone aggregate complete all as specified and directed. |
| 23 | S & F 105mmx60mm size and 1.60 mm thick pressed steel frames for doors with one or more rebates incl necessary fixing lugs, hinges, lock strike plate etc including applying a coat of tar in inner surface ,red oxide to outer surface and filling the frame using PCC M-10 using 12.50 mm graded stone aggregate complete all as specified and directed. |
| 24 | M&L for PCC (1:3:6) type C1 20mm graded aggregate as in padding ,holdfast/filling of chowkhats or similar work complete all as specified and directed. |
| 25 | S&F of factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge. (Note: stainless steel butt hinges and necessary S S screws shall be paid separately) |
| 26 | S&F of 35 mm thick PVC mosquto proof door shutter consisting of frame made out of M. S. tube of gauge thickness and size of 20 mm x 20 mm lipped with 5 mm Plain pvc sheet with stainless steel net with prelaminated sheet in desired colour complete all as specified and directed by engr in charge.(Note - minimum density 600 Kg /Cum ) |
| 27 | Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded prelam colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and prelam PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of both side Prelam PVC sheet to be fitted in the M.S frame welded/sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. complete all as specified and directed. |
| 28 | Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing complete all as specified and directed. |
| 29 | S & F of 150 mm long extruded anodised aluminium alloy handle, fabricated type complete all as specified and directed. |
| 30 | S & F of 150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed. |
| 31 | S & F of 200 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed. |
| 32 | S & F of 100 mm long mild steel butt hinges, medium weight cold rolled complete all as specified and directed. |
| 33 | S&F in repairs aluminum (extruded section) door closer hydraulically regulated designation No-2 universal type suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 kg complete all as specified and directed. |
| 34 | M & L for anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat ,louvers for fixing of glass in ventilators and powder coated (minimum thickness of powder coating 50 micron)etc. complete all as specified and directed |
| 35 | M&L for Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots ,necessary fittings and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 36 | M & L for 5.50 mm thick sheet glass, ordinary quality and glazing fixed in aluminium frames in square/rectangle not exc 0.5 sq. m in each pane complete all as specified and directed |
| 37 | S&F of stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed |
| 38 | S & F brass mortice lock, vertical type, size 65mm, 4 Levers with escutcheon plates & two keys fixed in door shutter complete all as specified and directed. |
| 39 | M & L for framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 40 | M & L for screed bed or bedding layer of mortar, 15 mm thick, in cement mortar 1:6, for laying floor finishes complete all as specified and directed. |
| 41 | M & L for rendering 10 mm thick in cement mortar 1:4 on fair faces of brick or concrete surfaces finished even and rough for receiving wall tiles/dado/skirting complete all as specified and directed. |
| 42 | M & L for double charged vitrified ceramic light shade coloured tiles 10 mm thick (Square or Rectangular) polished, area of each tile exec 0.42 but not exc. 1.00 Sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed. |
| 43 | M & L for double charged vitrified ceramic light shade coloured tiles 10 mm thick (Square or Rectangular) polished, area of each tile exec 0.42 sqm but not exc. 1.00 Sqm, as in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed. |
| 44 | M & L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square or Rectangular) area of each tile exc. 0.18 Sqm but not exc. 0.36 sqm, as in floor etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface of tile complete all as specified and directed. |
| 45 | M & L for glazed ceramic tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match to match the surface of tile complete all as specified and directed. |
| 46 | M&L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed |
| 47 | M&L for RCC (nominal mix) (1:2:4) type B1 using 20mm graged stone agreegate Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. |
| 48 | M & L for TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips, complete all as specified and directed. |
| 49 | M&L 18-20 mm Granite (of any type) thick machine cut, as in steps, jambs, pillars, window-cills, cooking platforms and like, for bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete including 20mm thick screed bed or bedding layer cement mortar (1:6) and making hole for gas pipeline complete all as specified and directed. |
| 50 | M&L Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed. |
| 51 | S & F in repairs kitchen sink without drainage board made of satinless steel 1 mm thick with plug washer and waste coupling including bedding in cement mortar to dwarf wall or including and fixing cantilever brackets and connecting union pipe overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm including flush pipe of polyethylene of low or high density or PVC 32mm bore with long screwed shanks and fly nuts complete all as specified and directed. |
| 52 | S&F in repair stainless steel kitchen plate rack of size 900mm x 1000mm x 200mm fabricated out of Ist quality 0.6mm thick stainless steel sheet and as approved by GE complete all as specified and directed. |
| 53 | S&F in repairs 15 mm bore CP sink cock with regular swinging spout (wall mounted) with wall flange screwed down for iron pipe and fixed complete all as specified and directed.( Minimum weight 15mm-1200 gms) |
| 54 | S&F laminated PVC kitchen cabinets of depth 300mm with decorative finish on one face and other face white,made out of 18mm thick outer box and 18mm thick shelves of density not less than 550 kg/cum and shutters complete including knobs, hinges. Fixed to walls with steel screw and PVC sleeves by drilling holes. complete all as specified and directed. (Note : Only front face is to be measured) |
| 55 | S&F laminated PVC kitchen cabinets of depth 610mm with decorative finish on one face and other face white,made out of 18mm thick outer box and 18mm thick shelves of density not less than 500 kg/cum and shutters complete including knobs, hinges. Fixed to walls with steel screw and PVC sleeves by drilling holes. complete all as specified and directed.(Note : Only front face is to be measured) |
| 56 | M&L for applying neat cement slurry over existing roof surface @ 3.0kg of cement per sq. metre complete all as specified and directed. |
| 57 | M&L for PCC (1:2:4) type B-0 using 10/12.5 mm graded stone aggregate laid over roof slab after applying cement slurry for filling undulations finsished even and smooth without using extra cement complete all as specified and directed. |
| 58 | M&L for 15 mm thick rendering in CM (1:3) mixed with liquid water proofing compound as per manufacturers instructions over RCC roof slabs for laying water proofing treatment and surface finished even and smooth complete all as specified and directed. Note :-(WPC will be measured and paid separately) |
| 59 | Supply and fix APP polymeric water proofing membrane,minimum 3mm thick and weighing not less than 3.5 kg/sqm,black finish reinforced with non-woven polyster reinforcement matt with a thermo fusable finish laid over compatible cold emulsion bituminous primer applied at the rate of 0.40 kg/sqm by torching with a propane or a butane gas torce with a overlap of 75 mm on a longitudinal direction and 100 mm on transverse direction including sealing all as per manufacturer's instruction complete all as specified and directed. Note : (i) Cover fillets in PCC (1:2:4) type B-0 using 12.5mm graded stone aggregateof radius 75mm shall be provided at the junction of roof and parapet wall/mumty/chimney/other vertical surfaces and thereafter surface painted with hot paving bitumen of grade 30/40 conforming to IS-73,applied @1.2 kg/sqm over a coat of bituminous primer conforming to IS-3384 appled @0.40 kg/sqm (ii) Polymeric membrane shall be taken to a height of 45 cm (minimum) and then inserted inside the groove of parapet wall of brick masonry and shall be finished by a membrane flushing (iii) The water proofing treatment shall be got carried out by the manufacturer or their authorized applicators (iv) In case of stone masonry parapet wall etc a groove of size 25mm x 25mm (minimum) shall be made in cover fillet at the junction of roof and parapet wall / mumpty/ other vertical surfaces and polymeric membrane inserted in groove and sealed with paving bitumen (v) Exposed surfaces of APP membrane shall be applied with one coat of bituminous aluminium paint @ 100gms/sqm |
| 60 | M&Lfor applying evenly a coat of blown type bitumen at the rate of 1.50 kg per square metre and blinding with clean dry sand @ 0.05 cu. m. per sq. m over APP membrane complete all as specified and as directed. |
| 61 | Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting exceeding 10 cm but not exc 20 cm girth complete all as specified and directed. |
| 62 | Supplying and laying of CPVC pipes Outer diameter of pipes :20mm SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including cutting through walls together with all tube fittings (such as bends, elbows, tees, short pieces, connectors, backnuts,diminishing pieces, caps, plugs and unions, etc.) and fixing complete with clips, wall hooks, wooden plugs, complete all as specified and directed. |
| 63 | Supplying and laying of CPVC pipes Outer diameter of pipes :32 mm SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including cutting through walls together with all tube fittings (such as bends, elbows, tees, short pieces, connectors, backnuts,diminishing pieces, caps, plugs and unions, etc.) and fixing complete with clips, wall hooks, wooden plugs, complete all as specified and directed. |
| 64 | S&F of 1000 litre capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and directed. |
| 65 | S&F of 20mm dia ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed |
| 66 | M&L for gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed of size 20mm dia complete all as specified and directed. |
| 67 | S & F coloured vitreous china half stall urinal with grating and union for discharge pipe including, waste pipe and PVC connection, bedding urinal against wall in cement mortar 1:2 securing urinal to to wall all as per manufacturer instructions complete all as specified and directed by Engineer-in-Charge. |
| 68 | S & F of curved shaped urinal partition with frosted glass 8mm/10mm thickness chrome finish fixing by cutting chase in wall and making good disturbed surfaces complete all as specified and directed. |
| 69 | S&F vitreous china table top wash basin with granite counter including cutting for and pinning in ends for bracket,and waste fittings 32 mm including waste pipe, brass chromium plated with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed complete all as specified and as directed. |
| 70 | S&F of 15 mm bore Pillar taps, cast copper alloy, with capstan heads,chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed. |
| 71 | S & F 6mm thick beveled edge mirror of selected quality glass mounted on 06 mm thick AC building board & fixed to wooden plugs with chromium plated brass screws & cup washers complete all as specified & directed. |
| 72 | S&F of towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 90gms)complete all as specified and directed. |
| 73 | S & F for 125mm dia PTMT grating doom with waste hole for waste pipe ( minimum weight 40 gram) complete all as specified and directed. |
| 74 | S & F of rimless single piece water closet WC, white, china ware wash down water closet pan with and including vitreous china flushigng cistern, plastic water closet seat white closed pattern with flat bottom and cover including fixing the same as per manufacturer instruction, jointing the water pipe etc by makeing hole in stone masonry wall and making good disturbed portion etc complete all as specified and directed. |
| 75 | S & F of 15mm bore brass chromium plated fancy type two way bib cock with wall flange screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed. |
| 76 | S & F Hand Shower (Health Faucet) with 58mm dia 1 metre long flexible tube with wall hook complete all as specified and as directed. |
| 77 | S & F chromium plated toilet paper holder with cover complete all as specified and directed. |
| 78 | S&F 15 mm dia Fancy type Chromium plated Angle valves, cast copper alloy screwed down high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed. |
| 79 | S&F for PVC connection pipe 15mm dia with PTMT nuts of length 600mm complete all as specified and directed. |
| 80 | S&F of 110 mm dia PVC (SWR) pipes single socketd, in any length with rubber ring joints fixed to wall with stack clamp complete all as specified and directed. |
| 81 | S&F of 75 mm dia PVC (SWR) pipes single socketed, in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed. |
| 82 | S&F in repair of 110 mm dia PVC (SWR) bends any radius complete all as specified and directed. |
| 83 | Taking down carefully copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches,ceiling roses,pendants,regulators,sockets,light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors etc. complete all as specified and directed. |
| 84 | M&L for Point wiring with PVC insulated and unsheathed FRLSH cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS - 694 1990 drawn through and including PVC concealed conduit 20mm dia medium duty with all accessories including modular GI boxes of suitable sizes including 1.5 sq mm FRLSH stranded PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for one light or fan point controlled by one switch single pole one way for light/ ceiling fan/ exhaust fan/call bell point/ Switch socket outlet 5 amps complete all as specified and as directed.Note: (i) Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board. (Rate deemed to be inclusive of cutting chases and making good disturbed surface). |
| 85 | All as per item No. 84 here-in-before but one 3 pin 5 amps switch socket commbination on the independent board with other switch complete all as specified and directed by Engineer-in-charge. |
| 86 | All as per item No. 84 here-in-before but one 3 pin 5 amps socket outlet on the same board with other switch complete all as specified and directed by Engineer-in-charge. |
| 87 | M & L for point wiring for socket out let on 16 Amps independent Boards controlled by one, one way switch using 2.5 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLS cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including metal flush box suitable for modular cover plate with frame of suitable size of 3M and 2.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLS PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed.Note: (i) Red coloured cable shall be used for live connection, black coloured cable shall be used for neutral connection and green coloured cable shall be used for earthing. Separate cable for earthing and neutral to be used for each individual circuit from the distribution board. (Rate deemed to be inclusive of cutting chases and making good disturbed surface). |
| 88 | S&F Modular type switch 6 Amps 230V AC single module one way complete all as specified and as directed. |
| 89 | S&F Modular socket out let 3 pin 10 Amps shuttered type 230V AC 2 module complete all as specified and as directed. |
| 90 | S&F Modular socket out let 3 pin 16 Amps shuttered type 230V AC 2 module complete all as specified and as directed. |
| 91 | S&F Modular type switch 16 Amps 230V AC single module one way complete all as specified and as directed. |
| 92 | S&F Ceiling rose, surface bakelite, 65 x 50 mm,three terminals complete all as specified and directed. |
| 93 | S&F Modular type fan regulator Step type,100 Watt, one module/ two module, 230V AC complete all as specified and as directed. |
| 94 | Supply and fixing modular white cover plate with frame 2 modules complete all as specified and as directed. |
| 95 | Supply and fixing modular white cover plate with frame 3 modules complete all as specified and as directed. |
| 96 | Supply and fixing modular white cover plate with frame 4 modules complete all as specified and as directed. |
| 97 | Supply and fixing modular white cover plate with frame 6 modules complete all as specified and as directed. |
| 98 | Supply and fixing modular white cover plate with frame 8 modules complete all as specified and as directed. |
| 99 | Supply and fixed 18 W LED light fitting wall mounted batten 4'ft , minimumm lumen output 120 lumen/Wat, extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 18 watt,6500K including necessary connection complete all as specified and directed. |
| 100 | Supply and fixed security light fittings 30 watts, minimumm lumen output 120 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65 including necessary connection complete including 25mm dia light grade GI bracket with nut bolt and clamp complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size complete all as specified and directed. |
| 101 | Supply and fixed recessed mounted 2' x 2 ' LED luminaire 36 watts for grid ceiling minimumm lumen output 120 lumen/Watt, pre-treated CRCA frame powder coated with diffused Profied including necessary connection complete all as specified and directed. |
| 102 | Supply and fixed 09 W LED light fitting wall mounted batten 2'ft , minimumm lumen output 120 lumen/Wat, extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 09 watt,6500K including necessary connection complete all as specified and directed. |
| 103 | Supply and fixed 12 W Surface panel mounted round LED downlight, aesthetically designed aluminium die-cast enclousers, with seperate replaceable constant current driver 12 watts, including necessary connection complete all as specified and directed. |
| 104 | Supply and fixing LED 9 W decorative wall light made up of high grade engineering plastic material including LED 9W complete as per manufacturer's instructions complete all as specified and directed. |
| 105 | Supplying and fixing in repair two single core ,6 sqmm nominal cross sectional area multistranded copper conductor FR cable, PVC insulated unsheathed 1100 Volts grade drawing in and including nd including suitable size PVC conduit (ISI marked) concealed including 6 sqmm nominal cross sectional area multistranded copper conductor FR cable, PVC insulated unsheathed 1100 Volts grade earth wire complete all as specified and directed(Rate deemed to be inclusive of cutting chases and making good disturbed surface). Note : Two run of 6 sqmm wire with one run of 6 sqmm and one run of conduit pipe shall be measured against one unit. |
| 106 | Supply and fixed in repairs epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Single pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as specified and directed. |
| 107 | Supply and fixed in repairs epoxy powder coated sheet metal enclosure for DBs, double door, Triple pole and neutral 415 V, 4 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as specified and directed. |
| 108 | Supply and fixed in repairs MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs including necessry connection complete all as specified and directed. |
| 109 | Supply and fixed in repairs MCB SPN 6-32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection complete all as specified and directed. |
| 110 | Supply and fixed in repairs MCB TPN 63 Amps, 'C' series 10kA, 415 Volts and to be housed in DBs complete including necessry connection complete all as specified and directed. |
| 111 | Taking down of AC ceiling / exhaust fan of any sweep & any height and opening the fan and oiling, greasing and replacement of unserviceable accessories and servicing, complete overhauling and re-assembling and testing complete for efficient functioning and hanging it back in position including provn of 0.5 Sqmm copper flexible twin twisted cable (length not exceeding 0.5 metre) from ceiling rose to fan complete all as specified as directed by the Engr-in-Charge. |
| 112 | Material and labour for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion. |
| 113 | Supply, laying / fixing / connecting, testing and commissioning of 16 Sqmm 4 core LT under ground cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cable (heavy duty) with multistranded aluminium conductor,1100 Volts grade in trenches/on wall/poles laid in ducts/inside protection pipe of the following cross sectional area including cable glands,lugs and suitable size of MS saddle clips (where ever cable laid in ceilings / walls without cable duct) complete all as specified and directed by the Engr-in-Charge. |
| 114 | NOTES:1. The amount of schedule of credit shall be deducted from the total of this BOQ for arriving at contract sum. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodayOct 29, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 2 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender