Tender For Addition/Alteration Of Bldg No T-06 Otm Accn Under Age B/R-Ii At Tibri Mil Stn Gurdaspur.
Tender Value
41 Lakhs
Estimated cost
Bid Submission
26 Oct 2026
11 days left
EMD
82000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Gurdaspur → Punjab
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition/Alteration Of Bldg No T-06 Otm Accn Under Age B/R-Ii At Tibri Mil Stn Gurdaspur.
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete of any description and in any position(above/below of ground level) not otherwise specifically provided as in sunken floor, plinth protection, roof kerb, foundation etc. all as specified and directed. |
| 2 | M&L for rendering 15mm thick in cm 1:3 in sunken portion of slab using waterproofing compound all as specified and directed (Note : Water proofing compound shall be measured and paid separately). |
| 3 | Supply only integral water proofing compound. |
| 4 | M&L for APP based polymeric membrane minimum weighing 3 kg/ sqm and minimum 3mm thick, reinforced with polyster non wove fabric (weight not less than 150 gms/ Sqm) laid on primed surface with bitumen primer @ 0.40 kg /Sqm by forced application with butane torch over entire roof area with minimum overlaps of 100mm at the sides/ longitudinal edges of strips membrane and 150mm at the ends and sealed in after cleaning surface complete all as specified and directed and all as per manufacturer's instructions. |
| 5 | M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sq.m including cleaning surfaces complete all as specified and directed. |
| 6 | M&L for PCC 1:5:10 type E2 using 40 mm graded stone agg as in filling, fdn and mass concrete in sunken floor complete all as specified and directed. |
| 7 | M&L 25 mm thick cement concrete 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregate) as in sub base for receiving the floor finishes complete all as specified and directed. |
| 8 | M&L for removing existing treatment ,all loose gravel cement mortar , dirt, oil, grease and foreign material by jet of dry air, roughening and clean the surface mechanically or by grinding to make it smooth before application loose existing bituminious material manually and with heat torch gun to get smooth plain finished surface with no loose material on surface . Repair all joints & cracks and apply primer with smart care epoxy primer to seal the pores/cracksand enhance the adhesion of the coating. • Apply first coat of fibres reinforced elastomeric liquid water proofing membrane formulated with PU hybrid poymers and reinforcing acrylic fibres with sun reflective index (SRI) of 100-110, having minimum elongation of 300% to 350%, tensile strength of 1.8 Mpa to 2.9 Mpa and shall have cracks bridging ability upto 10-12 degree celcius with 33% dilutioon of priming coat. Laying of fiber mesh of 0.3mm thickkness weave in leno pattern having 45 gsm/sqm and pasting it properly with overlap of 50 mm and allow it to dry for 10 to 12 Hrs. Apply second of undiluted coat @0.45ltr/sqm and allow it to dry for 4 to 5 Hrs. Apply third and final coat undiluted @0.45 ltr/sqm all as specified and as per manufacturers specification having warranty for 10 years. (Note : Application of water proofing treatment will be done by Authorised Applicator only). |
| 9 | M&L for cement concrete 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in flooring, padding complete all as specified. |
| 10 | M&L for PCC 1:2:4 type B1 (using 20mm graded crushed stone aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges with WPC complete all as specified and directed by Engineer-in-Charge.Note : WPC shall be measured and paid separately. |
| 11 | M&L for ceramic glazed dark shade coloured tiles of size 450x300x7mm thick joint free on and including 10mm thick cement screed bed in CM(1:4) set and jointed in neat cement slurry and pointed in colored cement mixed with pigment to match the colour of tiles on vertical surfaces of wall as in skirting/ dado including dismantling of existing tiles complete all as specified. |
| 12 | M&L for non skid dark coloured ceramic tiles 7 to 8 mm thick joint free (square/rectangular) area of each tile exceeding 0.11 sqm to 0.18sqm in floors etc set and jointed in neat cement slurry and pointed in white cement or clolured cement to match including 15 mm thick screed bed in CM 1:4 including removing of existing tiles complete all as specified. |
| 13 | M&L for green marble work 16-18mm thick (table rubbed and polished) in steps, jambs, pillars window cills, cooking platforms, stair case and the like in cement mortar ( 1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade including 15 mm thick screed bed in CM 1:4 and demolition of existing marble complete all as specified and directed. |
| 14 | M&L for 75mm thick cement cocnrete type C-1 (1:3:6) (20mm graded crushed stone aggregate) as in plinth protection finishing the surface even and fair complete all as specified and directed by Engineer-in-Charge. |
| 15 | M&L for repairing of RCC projections, chajjas, roofs, facia etc. by necessary preparations i.e. scrapping, cutting, chiseling, dusting and cleaning exposed reinforcement, surfaces of damaged edges, loose RCC surfaces and applying one coat of cement slurry and filling the surfaces with cement concrete 1:2:4 (using 12.5mm graded crushed stone aggregate) and finished with cement sand mortar (1:3) using coarse sand in patches (area n.exc 5 Sqm each) and thickness of RCC member exc 50mm including applying two coats of finishes to match with the existing surfaces in at any height complete all as specified. (Note: - Cost of formwork and welded mesh shall be deemed to be included in unit rate quoted by the Contractor). |
| 16 | S&F steel window box type made of ERW tube hollow P section of size 60mmX25mm double rebated outer frame comprising double shutters i.e. guaged skelton & glazed, shutter frame of ERW tube P section size 50mmX20mm with two openable leaf for each shutter consisting two Nos sash bar of T-section 20mmX3mm welded to frame with one vertical mullion of ERW box type T-section of size 60mmX25mm and flat iron 2mm thick welded/ screwed to frame for fixing of wire gauge including MS guard bars, fittings and fixtures welded to frame/ shutters as given below and all as shown on drg No. CEJZ/TD-1020/08 Sh 1/3 to 3/3 complete incl two coats of painting incl taking down old existing window :- (i) Hold fast,150mm long of flat iron 40mmX3mm- 04Nos per window (ii) Handle of Z section 20mmX25mm,100mm long-01Nos per leaf (iii) MS Tower bolt 150mm long-02 Nos per leaf (iv) Z section 20mmX25mm,100mm long stopper -01 Nos per leaf (v) Cleat 55mm long of hollow square 15mmX12mm -02 Nos per leaf (vi) MS pintol hinges size 75mmx12mm- 2 Nos. per leaf (vii) Making good dismantled portion in PCC 1:2:4 type B-1 for hold fasts (four Nos for each window). (viii) Painting with one shop coat of zinc chromate primer. Note: Wire cloth, glass shall be measured and paid for separately |
| 17 | S&F steel window/ ventilator box type made of ERW tube hollow P section of size 60mmX25mm outer frame (single rebated) comprising glazed skelton shutter frame of ERW tube P section including MS guard bars, fittings and fixtures welded to frame/ shutters all as shown on drg No. CEJZ/TD-1019/08 Sh 1/3 to 3/3 including Making good dismantled portion in PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) for hold fasts, painting with one shop coat of zinc chromate primer incl two coat of synthetic enamel painting incl taking down old existing window/ventilator complete all as specified and directed. Note: Glass/ wire cloth shall be measured and paid for separately |
| 18 | S&F 4mm thick sheet glass ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm each complete all as specifiwd and directed. |
| 19 | S&F figured glass/ pin head type glazing with oil puty glass 3mm thick, fixed with oil puty in square n. exe 0.5sqm in each pane. |
| 20 | S&F stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 21 | Taking down chowkhats with shutters (without taking off shutters from the frame) area not exceeding 1.5 Sqm each, and removing from site complete all as specified and directed. |
| 22 | All as per Srl item No 21 above but area exceeding 1.5 Sqm but not exceeding 4 Sqm each and removing from site complete all as specified and directed. |
| 23 | S&F pressed steel frames 1.25mm thick for door size of frame125 X 60mm with single or double rebates including necessary fixing lugs, hinges, lock strike plate and filling of chowkats with PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) and for filling of hold fast and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges two coats of synthetic enamel paint to outer surface with red oxide primer after prepration of surfaces and complete all as specified and directed. |
| 24 | S&F pressed steel frames 1.25mm thick for door size of frame 105 X 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate and filling of chowkats with PCC 1:3:6 type C-1 (using 20mm graded crushed stone aggregates) and for filling of hold fast and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges and two coats of synthetic enamel paint to outer surface with red oxide primer after prepration of surfaces complete all as specified and directed. |
| 25 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ceosetory windows & other frames/chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms)fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lug or stainless steel dash fasteners shall be paid for separately). Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. as per specification & drawing complete all as specified and directed. |
| 26 | S&F 35mm thick 2nd class hard wood glazed and skelton shutters as in doors open rebated and prepare to receive glass, gauze etc (without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part-I section 8 clause 8.24 (a) complete all as directed. |
| 27 | S&F of 35mm thick modular designer flush doors, solid core construction, with block board core and pre-lamination on both sides, complete all as specified and directed. |
| 28 | S&F factory made solid panel pace door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing. |
| 29 | S&F 100mm butt hinges, medium weight, cold rolled mild steel and fixed complete all as specified and directed. |
| 30 | S&F 150 mm long aluminium handles cast type complete all as specified and directed. |
| 31 | S&F 200mm long aluminium tower bolts of extructed section complete all as specified and directed. |
| 32 | S&F 250 mm aluminium, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed. |
| 33 | S&F in repairs floor door stopper140 mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed. |
| 34 | M&L for 15 mm thick rendering with ready mix mortar of approved make on brick work/stone/concrete wall, facia, projection, chajja etc. external surfaces finished even and smooth without using extra cement incl taking down existing plaster of any thickness incl raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed. |
| 35 | M&L for 12 mm thick rendering with ready mix mortar of approved make on brick work/stone/concrete wall etc. internal surfaces finished even and smooth without using extra cement incl taking down existing plaster of any thickness incl raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed. |
| 36 | M&L for 5 mm thick rendering with ready mix mortar of approved make on brick work/stone/concrete wall etc. internal surfaces finished even and smooth without using extra cement incl taking down existing plaster of any thickness incl raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed. |
| 37 | M&L for preparation of new plaster surface and applying two coats of cement base paint on wall surface complete all as specified and directed by Engineer-in-Charge. |
| 38 | M&L for preparation of new plastered surface and applying two coats of oil bound distemper, over and incl a 2mm layer of wall care putty to get even and smooth level finish on new plastered surface of internal wall, complete all as specified and as directed. |
| 39 | M&L for preparation of new plaster surface and applying three coat of white wash on ceiling complete all as specified and directed by Engineer-in-Charge. |
| 40 | M&L for prepration of old plastered surfaces of wall and applying two coats of cement base paint of shade as approved complete all as specified and directed. |
| 41 | M&L for preperation of old plastered surfaces ceiling and applying two coats of white wash including priming coat complete all as directed. |
| 42 | M&L for 75 mm thick, PCC (1:3:6), type C-2 (using 40 mm graded crushed stone aggregate), as in sub base under floor complete all as specified and directed. |
| 43 | M&L for 60 mm thick PCC (M-35) factory made with gray cement and pigment interlocking tiles/ paver block of shape/ size and conforming to IS 15658, joints will be filled with fine sand including dismantling of existing tiles complete all as specified and as directed by Engr-in-Charge. (Note Sand will be paid separately under relavent item). |
| 44 | M&L for PCC 1:2:4, type B-1 (using20mm graded crushed stone aggregate) as in coping for brick work, side benching complete all as specified and directed. |
| 45 | M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed by Engineer-in-Charge. |
| 46 | S&F in replacement of bib tap, 15 mm dia with wall flange made of cast copper alloy, chromium plated, complete all as directed. |
| 47 | S&F in replacement of pillar taps, 15 mm dia, cast copper alloy, with capstan heads, chromium plated, fancy type, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, complete all specified and directed. |
| 48 | S&F in replacement of stop cock with long shank and cup (concealed type), 15mm dia with wall flange, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe / unions, complete all as directed. |
| 49 | S&F in replacement of stop cock with long shank and cup, 15mm dia with wall flange, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe / unions, complete all as directed. |
| 50 | M&L for medium grade galvanised steel water tubing with and incl all fittings and fixtures, fixed to wall or laid in floors for 15 mm bore, concealed or exposed including taking down old pipe complete all as specified and directed. |
| 51 | M&L for medium grade galvanised steel water tubing with and incl all fittings and fixtures, fixed to wall or laid in floors for 20 mm bore, concealed or exposed, including taking down existing steel tubing with and incl connections, complete all specified and directed. |
| 52 | S&F of rotational moulded polyethylene cylindrical vertical with closed top water storage tank triple layered WHITE COLOUR 1000 Ltr capacity with connecting nipple, hoisted and fixed in position on new or existing foundation and making GI tubing inlet or outlet connection including taking down old complete all as directed. |
| 53 | S&F in repairs 20 mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed. |
| 54 | S&F in repair 20mm ball brass valves, high pressure, with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed complete all as specified and directed. |
| 55 | S&F in repair vitreous china wash basin, white, flat back, size 580x450mm excluding taps, waste chain and plug and porcelain stopper but including brackets, CP waste copling, including PTMT PVC connection 600mm complete all as specified and directed. |
| 56 | S&F brass CP shower rose 125 mm size with swivel joint fancy type with arm 225mm length including fixing to steel pipe or union complete all as specified and directed. |
| 57 | S&F PVC valveless, syphonic action flushing cistern 10 ltr capacity, low level, white, with inlet, ball valve , float and handle including brackets and PVC flush pipe 32mm dia complete all as specified. |
| 58 | S&F in repair towel rail 600mm Long of PTMT fixed with and including chromium plated brass screws and wooden/plastic cleats |
| 59 | S&F in repairs vitreous china squatting pan, 'Orissa' pattern, size 580 x 440 mm white with integral foot rests complete all as specified and directed. |
| 60 | Supply 600mm x 450 mm bevelled edge mirror of selected quality glass, mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plugs with chromium plated brass screws and cup washers. |
| 61 | Taking down eaves gutter and rain water pipes including all fittings any size and pattern. |
| 62 | S&F of PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors complete all as specified and directed. |
| 63 | S&F of PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end socketed, duly fixed with cement solvent etc, complete pipe duly laid in trenches or in floors complete all as specified and directed. |
| 64 | S&F of ringfit PVC (SWR) pipe of 110 mm nominal dia size, wall thickness of 3.5 mm, type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, complete all as specified and directed. |
| 65 | S&F of ringfit PVC (SWR) pipe of 75 mm nominal dia size, wall thickness of 3.5 mm, type A, in any length, single socketed type as per IS : 13592-1992 with latest amendment, having one end of the pipe as plain and other end as self socketed with an integral groove to hold the rubber gasket, with and incl rubber tighten gaskets, ringfit sockets etc, complete pipe duly fixed to wall, complete all as specified and directed. |
| 66 | S&F 110 mm bore PVC (SWR) bends of any radius complete all as specified and directed. |
| 67 | S&F 75 mm bore PVC (SWR) bends of any radius complete all as specified and directed. |
| 68 | S&F 110 mm bore PVC (SWR) junction single (Single `T') equal or unequal complete all as specified and directed. |
| 69 | S&F 75 mm bore PVC (SWR) junction single (Single `T') equal or unequal complete all as specified and directed. |
| 70 | S&F PVC floor trap of 75 mm outlet with grating including jointing to waste pipe in run lead complete all as specified and directed. |
| 71 | M&L for preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (ordinary tint) over a coat of pink primer complete all as specified and directed. |
| 72 | M&L for preparation of new or previously untreated steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer, complete all as specified and directed. |
| 73 | M&L for stainless steel curtain rod 25mm dia steel pipe cutting into length as required at site with and incl SS end caps/lobs and stainless steel wall mounting brackets, complete all as specified and directed. |
| 74 | Demolition of brick work built in cement mortar or lime mortar including all quoins arches, pillars etc complete all as specified and directed. |
| 75 | M&L for brick work with fly ash bricks, straight or curved on plan exc. 6m mean radius built in cement mortar 1:6 complete all as specified and directed. |
| 76 | M&L for half brick thick wall with fly ash bricks, straight or curved on plan to any radius built in cement mortar 1:4, complete all as specified and directed. |
| 77 | M&L for RCC 1:1.5:3, type B-0 (12.5mm graded crushed stone aggregate) slabs supported on walls, beams and columns in floors, roofs, landings, balconies, chajja, canopies, deck slabs and in shelves and the like. |
| 78 | M&L for mild steel deformed TMT bars 5 mm To 10mm dia (as in reinforcement) cut to length, bent to shape require including cranking, bending spirally for hooking for column, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 79 | Form work to soffits of suspended slabs such as roof slabs, floor slabs and lintels, chajja landingand similar work n exc 200mm thick. |
| 80 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc 10 sqm on plan and notexc1.5 m in depth and getting out complete all as specified & directed. |
| 81 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm. all as specified & directed. |
| 82 | Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point all as specified & directed. |
| 83 | Demolition and breaking up old unserviceable drain pipes (Salt glazed ware, AC or reinforced concrete)150 mm bore at any depth set in cement mortar includind PCC bed complete all as specified & directed. |
| 84 | M&L for PCC 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in concrete bed to drain pipes including packing under,and haunching against the sides of pipes after they are laid and tested complete all as specified & directed. |
| 85 | Supplying ,laying in trenches, jointing and testing reinforced concrete pipes 150mm, class NP3, laid and jointed complete with collars at any depth over PCC bed complete all as specified and directed. |
| 86 | S&F in replacement of PVC connection 450 x 15mm dia PTMT (PVC) complete all as specified and directed. |
| 87 | S&F in repair vitreous china urinal, half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete all as specified and directed. |
| 88 | S&F in repairs 32mm dia waste coupling of PTMT (half or full threaded) (minimum weight 32mm- 45gms/40mm-60 gms) complete all as specified and directed |
| 89 | S&F pre-painted galvantume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of and colour having tensile strength of 550 Mpa as in roof covering/ cladding to walls, fixed with self tapping screws including dismantling of old asbestos/corrugated/semicorrugated sheet complete all as specified and directed. |
| 90 | Dismantling framed work timber scantlings 40sqcm and over in section, in any position complete all as specified and directed. |
| 91 | Dismantling wrought iron and mild steel work of any description complete all as specified |
| 92 | S&F of rolled mild steel Gde Fe-410-W Gde E-250 Quality-A in roof trusses (framed), trussed, purlins crane gantries, joist, channel, steel tube, rails & fastenings & heavy brackets framimg (beam, tee, angle, coulmn, gusset plates, channel, hollow square/rectangular or flat section) including distance pieces, cleats with riveted, bolted or welded attachment etc. complete all as specified and directed by Engr-In-Charge. |
| 93 | E/M PORTION Taking down carefully aluminium/ copper point wiring for light, fan, bell, socket of point complete fiitings such as switches, ceiling roses, pendents, regulator socket etc complete at site and making goods disturbed surfaces of walls, floors etc complete all as specified and directed. |
| 94 | M&L for point wiring with PVC insulated and PVC unsheathed multistranded FRLSH copper conductor cable of size 1.5 Sqmm including existing concealed PVC conduit fittings and making good to the disturbed surfaces with continuous earth wire of copper 1.5 Sqmm dia to common earth including provn of 3mm thick plastic laminated sheet of appropriate size and fixing to CI/MS boxes for mounting of accessories like surfaces sockets and regulators etc. complete all as specified for One light / Fan/ bell point controlled by one way modular switch complete all as specified and directed. |
| 95 | All as per Srl item No 94 above but one 5 amp modular socket outlet on independent board. |
| 96 | All as per Srl item No 94 bove but one 5 pin modular socket outlet 5 amp on same board. |
| 97 | All as per Srl item No. 94 here-in-before but one light point controlled by two way modular switches. |
| 98 | All as per serial item No.94 here-in-before but wiring with 2.5 sqmm FRLSH copper wire including earth wire 2.5 Sqmm of copper for 15 Amps 3 pin socket outlet. |
| 99 | M&L for sub main wiring with two runs of single core multi stranded PVC insulated, copper conductor, grade 1100 Volt, FRLSH cable of size 6 sqmm (red for phase and black for neutral) including electrical grade PVC conduits of desired colour not less than 1.2 mm thick and 32mm dia and 6 sqmm multistranded copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete including taking down old unserviceable wiring complete all as specified and directed. |
| 100 | S&F in replacement of LED tube light fitting 20 watt for all purpose surface and wall mounted with single side connection polycarbonate LED batten with aluminium housing and integrated electronic driver of capacity 20W, four feet and connection with PVC insulated twin core 23/0.0076 twisted copper cable from ceiling rose to tube light fitting complete all as specified and directed. |
| 101 | S&F wall/ ceiling mounting LED 9/10 watt tube light fitting complete with all accessories 1x9 watt LED with CCT of 6000k suitable for demestic application 240 volts, 50 Hz and internallyu pre-wire with 1.5 sqmm twin twisted flexible cable copper conductor and connection complete all as specified and directed. |
| 102 | S&F modular fan regulator 5 step type size 100 watt complete all as specified and directed. |
| 103 | S&F modular lamp holder, PVC / polycarbonate type insulated body with back plate suitable for batten/ angle fittings complete al as specified and directed. |
| 104 | M&L for ceiling rose surface bakelite 65x50mm three terminal complete al as specified and directed. |
| 105 | S&F modular switch 1 way, 1 module 6 amps single pole one way complete all as specified and directed. |
| 106 | S&F modular socket, 2 module 6A 2/3 pin complete all as specified and directed. |
| 107 | S&F modular switch 1 way, 16 amps, 1 module complete all as specified and directed. |
| 108 | S&F modular socket, 6A/ 16A -2/3 pin combined, 2 module, complete all as specified and directed. |
| 109 | S&F modular switch 2 way, 6 amps, 1 module complete all as specified and directed. |
| 110 | S&F LED light fitting 1x9 watt/ 1x 10 watt bulkhead luminaries including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. |
| 111 | S&F in replacement GI pipe bracket made out of GI pipe light grade 32 mm bore and bent to shape 1.5m long, MS clamps made out of MS flat iron of size 32mm thick with nuts, bolts and washers complete including dismentling the existing GI pipe bracket and drilling of holes for nuts and bolts etc complete all as specified and directed. |
| 112 | S&F LED street light fitting 45 Watt 230V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and directed. |
| 113 | Taking down carefully ceiling fan complete fittings at site, removing fans, deposting to MES store yard and taking back to site for refixing complete all as specified and directed. Please Enable Macros to View BoQ information |
| 114 | Taking down carefully ceiling fan complete fittings at site, removing fans, deposting to MES store yard and taking back to site for refixing complete all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysNov 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 19 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender