Tender For Provn Of Sentry Post At Ge(P) North, Sri Vijayapuram
Tender Value
6.20 Lakhs
Estimated cost
Bid Submission
02 Nov 2026
1 days left
EMD
12400
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
South Andamans → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of Sentry Post At Ge(P) North, Sri Vijayapuram
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 26-Oct-2026 | Bid Auto Extn Corrigendum | Bid Auto Extn Corrigendum | 02-Nov-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | NOTE: 1. The bidders/ contractors are advised to read tender documents and all corrigendum/ amendments and General conditions of contracts before entry/ quoting the rates. |
| 2 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for |
| 3 | M&L for 40 mm thick PCC (1:2:4), Type B0 (Using 12.5 mm graded stone aggregate) as in flooring, finished even and smooth w/o using extra cement. all as specified and directed. |
| 4 | M&L Vitrified Ceramic tiles 10 mm thick jointless (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match. set and jointed in neat cement slurry over and including 15 mm thick screed bed of CM 1:6 and pointed in white/ coloured cement to match all as specified. |
| 5 | All as per item above but as in wall skirting over and including 10mm thick rendering of CM 1:4. |
| 6 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. and getting out in soft/loose soil |
| 7 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils in soft/loose soil |
| 8 | Removing excavated material exc. 250 m but n exc. 500 m and depositing where directed all as directed by Engr in charge |
| 9 | M&L for PCC Type D2 ,1:4:8 (Using 40 mm graded stone aggregate) as in foundation filling and mass concrete |
| 10 | Use and waste of form work to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished flat surfaces of concrete complete all as specified and directed. |
| 11 | M&L for RCC (nominal mix) Type A1 1:1.5:3 (using 20mm graded stone aggregate) in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed. |
| 12 | Use and waste of form work to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete, square, rectangular or polygonal, complete all as specified and directed. |
| 13 | M&L for RCC (nominal mix) type A1 1:1.5:3 (using 20mm graded stone aggregate) in columns, pillars, piers, posts and struts complete all as specified and directed. |
| 14 | Use and waste of form work to side and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels beam, tie beam, cantilevers, shelves including supports, overhangs, etc. also splays between floors and rough finished, complete all as specified and directed. |
| 15 | M&L for RCC (nominal mix) type A1 1:1.5:3 (using 20mm graded stone aggregate) in Beams, cantilevers, bressummers, tie beam, lintels over 1.5m span complete all as specified and directed. |
| 16 | M&L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed. |
| 17 | M&L for RCC (nominal mix) type A1 1:1.5:3 (using 20mm graded stone aggregate) in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and directed. |
| 18 | M&L TMT Bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 19 | All as item above but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders. |
| 20 | M & L for hardcore of gauge not exceeding 63 mm of broken stone, deposited, spread and leveled in layers not exceeding 15 cm thick, watered and rammed to a true surface. |
| 21 | M&L for 75 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) including finishing the surface even and fair complete all as specified and directed. |
| 22 | M&L for Pre-cast cement concrete block masonry with solid blocks type C1, 1:3:6 ( 20 mm graded aggregate) exc. 10 cm in width and setting in mortar 1: 6 , complete all as specified. |
| 23 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 and finished even and smooth without using extra cement. including mixing of water proofing compound wherever required as per manufacturers instructions and as direction by Engr in Charge (WPC shall be measured & paid separately). . |
| 24 | M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in Cement Mortar 1:6, finished even and smooth without using extra cement. all as specified and direction by Engr in Charge. |
| 25 | M&L fo Rendering 10 mm thick on fair faces of concrete surfaces in cement mortar 1:3 in ceiling of chajja, roof projection, shelve etc and finished even and smooth without using extra cement all as specified and direction by Engr in Charge. |
| 26 | Supply only liquid water proofing compound of approved quality. |
| 27 | M&L for Two coats of cement paint over a coat of priming plastered and other surfaces with alkali resistant priming paint through mechanical means including preparation of new surfaces, complete all as specified and directed. |
| 28 | M&L for 75 mm thick PCC 1:2:4 type B1 (using 20 mm graded stone aggregate) including finishing the surface even and fair complete all as specified and directed. |
| 29 | Providing and laying 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 50mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand all as specified and directed. |
| 30 | M&L for 20mm thick Granite work (Telephone Black/ Lakha Red) (table rubbed and pre-mirror polished) in single piece in steps, shelves and platforms ant the like set & jointed in neat cement slurry including pointing in epoxy grout to match with shade of granite, laid over and including 15mm thick screed bed in CM 1:4 omplete all as specified and directed. |
| 31 | Round chamfering, to the edges of granite slabs/marble slabs complete all as specified and directed. |
| 32 | M&L for 2 coats of distemper oil emulsion in wall surfaces white or tinted through mechanical means over a coat of 1mm thick wall care putty, including preparation of new surface all as specified. |
| 33 | M&L for preparing new plastered on wall and applying three coats of white wash. |
| 34 | S&F second class hard wood plain, solid, straight chowkats and frames wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints. |
| 35 | S&F of 35mm thick IInd class hardwood factory made plain, framed, panelled shutters (any number of panels) factory made with lock rail and panel of 9 mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and directed. |
| 36 | S&F 35mm thick 2nd class hard wood glazed and skeleton shutter as in door open rebated and prepared to receive glass, gauge etc. (without sash bars) edges of framing plain, chambered or rounded mitred and beads for securing glass etc. size of members of shutter as specified in SSR part-I, Sec-08, Clause 8.24(a), kiln seasoned and chemically pressure treated complete all as specified and as directed. |
| 37 | S&F 125mm long Butt hinges, medium weight, cold rolled mild steel, |
| 38 | S&F for 200mm aluminium anodised barrel tower bolts of extruded section and fixed. |
| 39 | S&F 300mm long aluminium alloy, anodised, sliding door bolts with hasp, staple (bolt type) and fixing clip of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed. |
| 40 | S&F 150mm Aluminium handles, cast type anodised. |
| 41 | M&L Preparation of new steel surfaces of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide priming. |
| 42 | S&F Powder coating (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as direction by Engr in Charge. |
| 43 | S&F Powder coating (minimum thickness of powder coating 50 micron) anodised aluminium sliding window and ventilator shutters, aluminium sections weighing not less then 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings complete all as specified and as direction by Engr in Charge.( Note : sheet Glass and SS wire mesh shall be measured & paid separately). . |
| 44 | S&F in stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples including beads all as specified and directed |
| 45 | S & F in 4.8 mm thick sheet glass ordinary quantity and glazing with oil putty in squares not exceeding 0.50 sqm in each pane. |
| 46 | Material and labour for Point wiring complete with 1100 volts grade, 1.5Samm (nominal area), single core, PVC insulated, unsheathed, mult-stranded copper conductor cable FRLSH drawn through and including medium grade, rigid, nonmetallic PVC conduit of suitable size not less than 20mm dia, with all necessary fittings, concealed in wall/ roof /floor duly earthed with one run of single core cable of same discription but green in colour as continuous earthing wire connected to common earth dolly fincluding 1.6mm thick fabricated MIS sheet terminal box, flush mounting in the wall for mounting switchs/ switche socket combinationl fan regulators etc., covered with 3mm thick plastic laminated sheet complete all as specified for the following:- |
| 47 | (a) One light point controlled by one Switch |
| 48 | (b) One Ceiling/Exhaust Fan/ Wall Mount Fan controlled by One Switch |
| 49 | (c) One 5A 2pin/3pin switch socket out let multipurpose on Same Board |
| 50 | (d) One 5A 2pin/3pin switch socket out let multipurpose on Independent board |
| 51 | Supply and fix on modular switch 1 way 6A, 1 module all as specified |
| 52 | Supply and fix Modular socket 6A 2/3 pin, combined 2 module all as specified |
| 53 | S&F Ceiling rose, PVC/ polycarbonate isolated body with three terminals, ISI marked all as directed |
| 54 | Supply and fixing led lights fitting 1x20w, 220v, AC decorative box type with dirver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete |
| 55 | Supply & fixing wall mounted fan 400mm sweep with blades, mounting accesories kit, blade guard set, guard ring, AC 230V with 90 degree oscillation and having speed and oscillation control by two pull cords system complete all as specified and as directed. |
| 56 | Material and labour for sub main wiring with two runs of single core FRLS PVC insulated, multistranded unsheathed copper conductor cable of size 4 square mm and drawing through casing and capping of suitable size with accessories along with one run of 4 square mm PVC insulated unsheathed multi stranded 1100 volts grade with copper conductor cable as earth continuity conductor connected to earth and earth dolly, connecting to main board duly making good the disturbed wall surfaces to match with the surroundings complete all as specified and directed.Note: 3 runs of 4 sqmm cableand 1 run of PVC casing and capping of suitable size with accessories shall be measured as 1 unit Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 26, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Nov 02, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 1 dayNov 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 1 dayNov 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender