Tender For Amrut-Implementation Of Amrut 2.0 24X7 Water Supply Proposal-For Guruvayur Municipality-General Civil Work
Tender Value
8.50 Crore
Estimated cost
Bid Submission
23 Oct 2026
5 days left
EMD
2 Lakhs
Bank guarantee accepted
Document Fee
11025
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Thrissur → Kerala
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Amrut-Implementation Of Amrut 2.0 24X7 Water Supply Proposal-For Guruvayur Municipality-General Civil Work
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 07-Oct-2026 | Other Corrigendum | Other | 23-Oct-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | Supply and Laying of New Distribution network in DMA - PVC pipes |
| 2 | 100.98.213:Supply of PVC Pipe, 6kg/cm2, 90mm Dia. |
| 3 | 100.98.214:Supply of PVC Pipe, 6kg/cm2, 110mm Dia. |
| 4 | 100.98.215:Supply of PVC Pipe, 6kg/cm2, 140mm Dia. |
| 5 | 100.98.216:Supply of PVC Pipe, 6kg/cm2, 160mm Dia. |
| 6 | 100.1.1:Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed, within a lead of 50m, in all kinds of soil. |
| 7 | 2.20.2:Open timbering in trenches including strutting and shoring complete ( measurements to be taken of the face area timbered ):Depth exceeding 1.5 m but not exceeding 3 m |
| 8 | 100.7.1:Bailing out water with 5HP engine and pump set including conveyance to the site, erecting, dismantling and taking back of engine and pump, cost of fuel lubricating oil and other stores pay of staff etc., complete. |
| 9 | 100.8.1:Fencing one side of trenches, 1.50m height with two rows of 10cm plastic caution tape in vertical casuarina pole (girth 15cm to 24cm) fixed at 2m intervals. |
| 10 | 100.9.8:Laying uPVC pipes of class 2 to class 6 and specials, lowering to the trenches already made, placing in position aligning the pipeline to the lines and levels and jointing the pipes and specials with solvent cement and testing the pipeline with water to the required test pressure (excluding cost of pipes and specials): 90 mm nominal outside diameter pipes. |
| 11 | 100.9.9:Laying uPVC pipes of class 2 to class 6 and specials, lowering to the trenches already made, placing in position aligning the pipeline to the lines and levels and jointing the pipes and specials with solvent cement and testing the pipeline with water to the required test pressure (excluding cost of pipes and specials): 110 mm nominal outside diameter pipes. |
| 12 | 100.9.10:Laying uPVC pipes of class 2 to class 6 and specials, lowering to the trenches already made, placing in position aligning the pipeline to the lines and levels and jointing the pipes and specials with solvent cement and testing the pipeline with water to the required test pressure (excluding cost of pipes and specials): 140 mm nominal outside diameter pipes. |
| 13 | 100.9.11:Laying uPVC pipes of class 2 to class 6 and specials, lowering to the trenches already made, placing in position aligning the pipeline to the lines and levels and jointing the pipes and specials with solvent cement and testing the pipeline with water to the required test pressure (excluding cost of pipes and specials): 160 mm nominal outside diameter pipes. |
| 14 | 100.59.1:Cutting the bituminous / concrete roads with cutting machine for a minimum depth of 200mm along the sides of proposed alignment of the pipe to be laid without causing any damage to other utilities, including the charges for hire and conveyance of tools and plant, cost of consumables and charges for lighting, watching, ribbon fencing, caution boards, traffic diversion, and as per the direction of departmental officers etc. complete, before carrying out the demolition of bituminous / concrete road by mechanical means and carrying out the excavation. |
| 15 | 15.59:Dismantling of flexible pavement ( bituminous courses ) by mechanical means and disposal of dismantled material up to a lead of 1 kilo metre, as per direction of Engineer-in-charge. |
| 16 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 17 | 16.78.1:Construction of granular sub- base by Providing close graded Material conforming to specifications, mixing in a mechanical mix plant at OMC, Carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in- Charge.With Material conforming to Grade - I ( size range 75 mm to 0.075 mm) having CBR Value- 30 |
| 18 | 4.1.4:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (1 Cement : 2 coarse sand (zone-III) derived from natural sources : 4 gradedstone aggregate 40 mm nominal size derived from natural sources) |
| 19 | 100.98.509:Supply of CI Plain End Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 200mm. |
| 20 | 100.31.1.5:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 200mm diameter, Class I. |
| 21 | 100.98.508:Supply of CI Plain End Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 150mm. |
| 22 | 100.31.1.4:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 150mm diameter, Class I. |
| 23 | 100.98.506:Supply of CI Plain End Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 100mm. |
| 24 | 100.31.1.2:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 100mm diameter, Class I. |
| 25 | 100.98.505:Supply of CI Plain End Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 80mm. |
| 26 | 100.31.1.1:Conveying and fixing C.I. sluice valves (with cap) by providing bolts, nuts, rubber insertions etc., complete, but excluding the cost of the valve (tail pieces, if required, will be paid separately): 80mm diameter, Class I. |
| 27 | 100.98.444:Supply of CI Air Valve, Conforming to IS 14848 - 2000, Single Orifice, Large Orifice Type S2, Size 50mm. |
| 28 | 100.32.3:Conveying and fixing C. I. Double Acting Air Valve of approved quality with bolts, nuts, rubber insertions etc., complete, but excluding the cost of air valve (tail pieces, if required, will be paid separately): 50mm Double Acting Air Valve. |
| 29 | 100.98.441:Supply of CI Air Valve, Conforming to IS 14848 - 2000, Single Orifice, Small Orifice Type S1, Size 40mm. |
| 30 | 100.32.2:Conveying and fixing C. I. Single Acting Air Valve of approved quality with bolts, nuts, rubber insertions etc., complete, but excluding the cost of air valve (tail pieces, if required, will be paid separately): 40mm Single Acting Air Valve. |
| 31 | 100.98.440:Supply of CI Air Valve, Conforming to IS 14848 - 2000, Single Orifice, Small Orifice Type S1, Size 25mm. |
| 32 | 100.32.1:Conveying and fixing C. I. Single Acting Air Valve of approved quality with bolts, nuts, rubber insertions etc., complete, but excluding the cost of air valve (tail pieces, if required, will be paid separately): 25mm Single Acting Air Valve. |
| 33 | OD142921/2026-2027: Supplying and fixing 150mm CID Joint including all accessories |
| 34 | OD142924/2026-2027:Supplying and fixing 80mm CID Joint including all accessories |
| 35 | 18.17.6:Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :80 mm nominal bore |
| 36 | OD142925/2026-2027:Linking charges to 160mm PVC to 90mm PVC line including specials, Earth work and all other charges |
| 37 | OD142922/2026-2027:Linking charges to 140mm PVC to 90mm PVC line including specials, Earth work and all other charges |
| 38 | OD142923/2026-2027:Linking charges for all branches from distribution main including earth work , etc complete |
| 39 | Supply of PVC Specials |
| 40 | OD142872/2026-2027:Supply of 160mm x140mm PVC Reducer |
| 41 | OD142873/2026-2027:Supply of 160mm x 110mm PVC Reducer |
| 42 | OD142852/2026-2027:Supply of 160mm x 90mm PVC Reducer |
| 43 | OD142878/2026-2027:Supply of 140mm x 110mm PVC Reducer |
| 44 | OD142853/2026-2027:Supply of 140mm x 90mm PVC Reducer |
| 45 | OD142888/2026-2027:Supply of 110mm x 90mm PVC Reducer |
| 46 | OD142916/2026-2027:Supply of 160mm x 140mm PVC Reducer Tee |
| 47 | OD142885/2026-2027:Supply of 160mm x 110mm PVC Reducer Tee |
| 48 | OD142859/2026-2027:Supply of 140mm x 110mm PVC Reducer Tee |
| 49 | OD142908/2026-2027:Supply of 140mm x 90mm PVC Reducer Tee |
| 50 | OD142866/2026-2027:Supply of 110mm x 90mm PVC Reducer Tee |
| 51 | OD142867/2026-2027:Supply of 160 mm PVC Coupler |
| 52 | OD142879/2026-2027:Supply of 140 mm PVC Coupler |
| 53 | OD142905/2026-2027:Supply of 110 mm PVC Coupler |
| 54 | OD142850/2026-2027:Supply of 90 mm PVC Coupler |
| 55 | OD142900/2026-2027:Supply of 160 mm PVC Elbow |
| 56 | OD142910/2026-2027:Supply of 140 mm PVC Elbow |
| 57 | OD142861/2026-2027:Supply of 110 mm PVC Elbow |
| 58 | OD142898/2026-2027:Supply of 90 mm PVC Elbow |
| 59 | OD142890/2026-2027:Supply of 140 mm PVC 45 Deg Bend |
| 60 | OD142918/2026-2027:Supply of 110 mm PVC 45 Deg Bend |
| 61 | OD142906/2026-2027:Supply of 90 mm PVC 45 Deg Bend |
| 62 | OD142899/2026-2027:Supply of 160 mm PVC TEE |
| 63 | OD142887/2026-2027:Supply of 140 mm PVC TEE |
| 64 | OD142909/2026-2027:Supply of 110 mm PVC TEE |
| 65 | OD142874/2026-2027:Supply of 90 mm PVC TEE |
| 66 | OD142915/2026-2027:Supply of 160 mm PVC End Cap |
| 67 | OD142865/2026-2027:Supply of 140 mm PVC End Cap |
| 68 | OD142864/2026-2027:Supply of 110 mm PVC End Cap |
| 69 | OD142902/2026-2027:Supply of 90 mm PVC End Cap |
| 70 | OD142858/2026-2027:Supply of 160 mm PVC FTA |
| 71 | OD142871/2026-2027:Supply of 140 mm PVC FTA |
| 72 | OD142891/2026-2027:Supply of 110 mm PVC FTA |
| 73 | OD142881/2026-2027:Supply of 90 mm PVC FTA |
| 74 | OD142876/2026-2027:Supply of 160 mm PVC MTA |
| 75 | OD142882/2026-2027:Supply of 140 mm PVC MTA |
| 76 | OD142917/2026-2027:Supply of 110 mm PVC MTA |
| 77 | OD142903/2026-2027:Supply of 90 mm PVC MTA |
| 78 | OD142913/2026-2027:Supply of PVC service saddles 200/160/140/110/90/75/63/50 mm. |
| 79 | OD142857/2026-2027:Supply of 160 mm PVC Tail Piece |
| 80 | OD142862/2026-2027:Supply of 140 mm PVC Tail Piece |
| 81 | OD142856/2026-2027:Supply of 110 mm PVC Tail Piece |
| 82 | OD142854/2026-2027:Supply of 90 mm PVC Tail Piece |
| 83 | OD142868/2026-2027:Supply of 63x50 mm PVC Reducer Tee |
| 84 | OD142892/2026-2027:Supply of 75x50 mm PVC Reducer Tee |
| 85 | OD142893/2026-2027:Supply of 75x63 mm PVC Reducer Tee |
| 86 | OD142904/2026-2027:Supply of 90x50 mm PVC Reducer Tee |
| 87 | OD142883/2026-2027:Supply of 90x63 mm PVC Reducer Tee |
| 88 | OD142880/2026-2027:Supply of 90x75 mm PVC Reducer Tee |
| 89 | OD142912/2026-2027:Supply of 63x50 mm PVC Reducer |
| 90 | OD142886/2026-2027:Supply of 75x50 mm PVC Reducer |
| 91 | OD142901/2026-2027:Supply of 75x63 mm PVC Reducer |
| 92 | OD142896/2026-2027:Supply of 90x50 mm PVC Reducer |
| 93 | OD142863/2026-2027:Supply of 90x63 mm PVC Reducer |
| 94 | OD142877/2026-2027:Supply of 90x75 mm PVC Reducer |
| 95 | OD142897/2026-2027:Supply of 75 mm PVC End Cap |
| 96 | OD142895/2026-2027:Supply of 63 mm PVC TEE |
| 97 | OD142869/2026-2027:Supply of 75 mm PVC TEE |
| 98 | OD142919/2026-2027:Supply of 63 mm PVC 45 Deg Bend |
| 99 | OD142855/2026-2027:Supply of 75 mm PVC 45 Deg Bend |
| 100 | OD142914/2026-2027:Supply of 63 mm PVC Elbow |
| 101 | OD142894/2026-2027:Supply of 75 mm PVC Elbow |
| 102 | OD142860/2026-2027:Supply of 63 mm PVC Coupler |
| 103 | OD142870/2026-2027:Supply of 75 mm PVC Coupler |
| 104 | OD142907/2026-2027:Supply of 63 mm PVC Tail Piece |
| 105 | OD142851/2026-2027:Supply of 75 mm PVC Tail Piece |
| 106 | OD142884/2026-2027:Supply of 63 mm PVC MTA |
| 107 | OD142911/2026-2027:Supply of 75 mm PVC MTA |
| 108 | OD142889/2026-2027:Supply of 63 mm PVC FTA |
| 109 | OD142875/2026-2027:Supply of 75 mm PVC FTA |
| 110 | Supply and Laying of New Distribution network in DMA - G.I Pipes |
| 111 | OD142849/2026-2027:Supplying of 150mm GI Pipe |
| 112 | 100.12.11:Conveying and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc., but excluding cost of pipes and fittings for External work: 150mm diameter nominal bore. |
| 113 | OD142847/2026-2027:Supplying of 125mm GI Pipe |
| 114 | 100.12.10:Conveying and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc., but excluding cost of pipes and fittings for External work: 125mm diameter nominal bore. |
| 115 | OD142848/2026-2027:Supplying of 100mm GI Pipe (Meadium) DLPC |
| 116 | 100.12.9:Conveying and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc., but excluding cost of pipes and fittings for External work: 100mm diameter nominal bore. |
| 117 | 18.12.8:Providing and fixing G.I. pipes complete with G.I fittings including trenching and refilling etc. External work80 mm dia nominal bore |
| 118 | Supply of GI Specials |
| 119 | OD142952/2026-2027:Supply of 80 mm GI Elbow |
| 120 | OD142936/2026-2027:Supply of 100 mm GI Elbow |
| 121 | OD142945/2026-2027:Supply of 150 mm GI Elbow |
| 122 | OD142935/2026-2027:Supply of 80 mm GI Socket |
| 123 | OD142942/2026-2027:Supply of 100 mm GI Socket |
| 124 | OD142948/2026-2027:Supply of 150 mm GI Socket |
| 125 | OD142938/2026-2027:Supply of 80 mm GI Union |
| 126 | OD142946/2026-2027:Supply of 100 mm GI Union |
| 127 | OD142947/2026-2027:Supply of 150 mm GI Union |
| 128 | OD142930/2026-2027:Supply of 80 mm GI TEE |
| 129 | OD142939/2026-2027:Supply of 100 mm GI TEE |
| 130 | OD142949/2026-2027:Supply of 150 mm GI TEE |
| 131 | OD142940/2026-2027:Supply of 80 mm GI Flange |
| 132 | OD142950/2026-2027:Supply of 100 mm GI Flange |
| 133 | OD142932/2026-2027:Supply of 150 mm GI Flange |
| 134 | OD142929/2026-2027:Supply of 80 mm GI Check Nut |
| 135 | OD142927/2026-2027:Supply of 100 mm GI Check Nut |
| 136 | OD142941/2026-2027:Supply of 80 mm GI Tank Nipple |
| 137 | OD142934/2026-2027:Supply of 100 mm GI Tank Nipple |
| 138 | OD142937/2026-2027:Supply of 80 mm GI Nipple |
| 139 | OD142953/2026-2027:Supply of 100 mm GI Nipple |
| 140 | OD142928/2026-2027:Supply of 150 mm GI Nipple |
| 141 | OD142943/2026-2027:Supply of 80 mm GI Cross |
| 142 | OD142931/2026-2027:Supply of 100 mm GI Cross |
| 143 | OD142944/2026-2027:Supply of 150 mm GI Cross |
| 144 | OD142933/2026-2027:Supply of 80 mm GI plug |
| 145 | OD142951/2026-2027:Supply of 100 mm GI plug |
| 146 | OD142926/2026-2027:Supply of 150 mm GI plug |
| 147 | Supply and Laying of New Distribution network in DMA- 200mm DI Pipe |
| 148 | 100.1.1:Excavating trenches of required width for pipes, cables, etc., including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth, including consolidating each deposited layer by ramming, watering, etc., and disposing of surplus excavated soil as directed, within a lead of 50m, in all kinds of soil. |
| 149 | 100.14.3:Conveying and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS: 8329 excluding cost of pipes and specials: 200mm diameter Ductile Iron Class K-9 Pipes. |
| 150 | 100.98.117:Supply of DI K9 Pipe Conforming to IS 8329/2000, 200mm Dia. |
| 151 | 18.67.1:Providing and laying S & S C.I. Standard specials suitable for mechanical jointing as per IS 13382:Upto 300 mm dia |
| 152 | 18.70.3:Providing push - on-joints to Centrifugally (Spun) Cast Iron Pipes or Ductile Iron Pipes including testing of joints and including the cost of rubber gasket:200 mm dia pipes |
| 153 | OD142824/2026-2027:Labour for cutting 200 mm diameter D.I. pipe |
| 154 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 155 | 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 156 | 100.37.7.1:In situ fabrication of M.S. pipes of size 200mm (I.D.) using 8mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete. |
| 157 | 100.37.7.3:Cutting 200mm (I.D.) M.S. pipes for making bends and other specials by gas cutting including cost of gas, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 158 | 100.37.7.2:Fabricating M.S. flanges of diameter 200mm using 12mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 159 | 100.37.7.4:Welding 200mm (I.D.) M.S. pipes for making bends and other specials by gas/electric welding machine including cost of gas and welding rods, all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 160 | 100.37.7.5:Grinding cut and weld edges of 200mm (I.D.) M.S. pipes during fabrication work including all labour and hire charges of tools etc., complete: For pipes fabricated with 8mm thick M.S. plates. |
| 161 | 18.31.4.2:Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately):200 mm diameterClass II |
| 162 | 18.59.2:Providing and fixing C.I double acting air valve of approved quality with bolts, nuts, rubber insertion etc. complete ( The tail pieces, tapers etc. if required will be paid separately):80 mm dia |
| 163 | 100.98.457:Supply of CI Double Flanged Sluice Valve Conforming to IS 14846 - 2000, Sluice Valve with Cap PN 1.6, Size 80mm. |
| 164 | OD142823/2026-2027:Supply of 80 mm MS Flange (12 mm Thick) |
| 165 | OD142827/2026-2027:Supplying of 80mm GI pipe Cl. Medium |
| 166 | OD142826/2026-2027:Supplying and fixing 200mm MS Saddle/Clamp including washer nut bolt etc complete |
| 167 | OD142825/2026-2027:FROM SPEC 18.31.5.2 Providing and fixing C.I. sluice valves (with cap) complete with bolts, nuts, rubber insertion etc. (the tail pieces if required will be paid separately):200 mm diameterClass II |
| 168 | Construction of Valve Chamber |
| 169 | 2.8.1:Earth work in excavation by mechanical means (Hydraulic excavator) /manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil |
| 170 | 2.26.1:Extra for every additional lift 1.5 m or part there of in excavation / banking excavated or stacked materials.All kinds of soil |
| 171 | 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 172 | 5.1.2:Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level:1:1:5:3 (1 cement 1.5 coarse sand :3 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 173 | 5.22A.6:Steel reinforcement for R.C.C work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo - Mechanically Treated bars of grade Fe-500D or more |
| 174 | 5.9.1:Centering and shuttering including strutting, etc. and removal of form for:Foundations, footings, bases of columns, etc for mass concrete |
| 175 | 5.9.2:Centering and shuttering including strutting, etc. and removal of form for:Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc. |
| 176 | 13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand) |
| 177 | 100.41.33:Supplying and fixing 500mm dia C.I. manhole cover with frame (medium duty) charges including all cost, labour charges etc., complete. |
| 178 | OD142829/2026-2027:Providing and fixing 100 mm dia GI pipe for a length of 1.5 m long as protection tube to below 150 mm sluice valve in the pipe line/ distribution system |
| 179 | Providing New FHTCs- 2000 No.s |
| 180 | OD142972/2026-2027:Shifting existing house connection from existing PVC / HDPE mains from 90 mm up to 160 mm dia., up to a length of 5m using 20mm Indian Standard Class 6 uPVC pipe and uPVC / GM/ Brass specials viz. brass ferrule, GM full way wheel valve, Elbow, MTA, FTA, couplers, PVC Service Saddle of suitable size etc. and connecting with the mains, testing the joints etc. complete including trenching and refilling in all kinds of soil up to a depth of 1.50m for main line tracing and trench of average cross section 0.3m x 0.75m for laying connection pipe and service pipe, fixing water meter, lighting, watching, providing caution boards, traffic control etc. complete including cost of materials, hire for tools, cost of consumables and labour charges but excluding cost of water meter and meter box and excluding charges for cutting the concrete / tarred / bituminous roads etc, and as per the direction of the departmental officers. |
| 181 | 100.60.1.1.2:Providing 15mm (1/2 inch) house connection with 15mm (1/2 inch) water meter from existing PVC / HDPE mains up to 110 mm dia., up to a length of 5 m using 20mm Indian Standard Class 6 uPVC pipe and uPVC / GM / Brass specials viz. brass ferrule, GM full way wheel valve, Elbow, MTA, FTA, couplers, PVC Service Saddle of suitable size etc. and connecting with the mains, testing the joints etc. complete including trenching and refilling in all kinds of soil up to a depth of 1.50m for main line tracing and trench of average cross section 0.3m x 0.75m for laying connection pipe and service pipe, fixing water meter, lighting, watching, providing caution boards, traffic control etc. complete including cost of materials, hire for tools, cost of consumables and labour charges, including the cost of tested Class B Multijet water meter with ISI mark and weather resistant PP / PE meter box of minimum size 300mm x 200mm x 150mm, but excluding charges for cutting the concrete / tarred / bituminous roads etc, and as per the direction of the departmental officers. |
| 182 | 100.60.2.1.2:Providing 15mm (1/2 inch) house connection with 15mm (1/2 inch) water meter from existing PVC / HDPE mains from 140mm to 200mm dia., up to a length of 5 m using 20mm Indian Standard Class 6 uPVC pipe and uPVC / GM / Brass specials viz. brass ferrule, GM full way wheel valve, Elbow, MTA, FTA, couplers, PVC Service Saddle of suitable size etc. and connecting with the mains, testing the joints etc. complete including trenching and refilling in all kinds of soil up to a depth of 1.50m for main line tracing and trench of average cross section 0.3m x 0.75m for laying connection pipe and service pipe, fixing water meter, lighting, watching, providing caution boards, traffic control etc. complete including cost of materials, hire for tools, cost of consumables and labour charges, including the cost of tested Class B Multijet water meter with ISI mark and weather resistant PP / PE meter box of minimum size 300mm x 200mm x 150mm, but excluding charges for cutting the concrete / tarred / bituminous roads etc, and as per the direction of the departmental officers. |
| 183 | 100.60.10.4.1:Providing 20mm (1/2 inch) PVC Air Valve in the water meter assembly for 15mm connection, using 20mm Indian Standard Class 6 uPVC pipes and specials including cost of materials, consumables, hire for tools and labour charges etc. complete and as per the directions of the department officers. |
| 184 | 100.60.3.1.1:Providing additional length of house connection pipe using 20mm Indian Standard Class 6 uPVC pipe and specials and testing the joints etc., by trenching and refilling in all kinds of soil with trench of average cross section 0.3m x 0.75m for laying of connection pipe and service pipe, lighting, watching, providing caution boards, traffic control etc., including cost of materials, hire for tools, cost of consumables and labour charges etc. complete, but excluding the cost of cutting of concrete / tarred / bituminous roads etc., and as per the directions of the department officers |
| 185 | 100.60.23.3.1:Providing 15mm PVC Tap in the water meter assembly for 15mm ( 1/2 inch ) water connection, using 20mm ( 1/2 inch ) Indian Standard uPVC Class 6 pipes, uPVC specials and PP PN 16 Compression specials including cost of materials, consumables, hire charges for tools and labour charges etc. complete and as per the direction of departmental officers. |
| 186 | 15.2.1:Demolishing cement concrete manually / by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in-Charge.Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) |
| 187 | 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 188 | OD142970/2026-2027:Providing stand post by using 75mm PVC pipe bits including cost, conveyance and all labour charges etc. |
| 189 | OD142971/2026-2027:Providing casing pipe 32mm GI Pipe as casing pipe |
| 190 | OD142973/2026-2027:Cost of Geo Tagging |
| 191 | Providing SCADA system for Monitoring |
| 192 | OD142834/2026-2027:Supplying an electro-magnetic flow meter of size 250 mm conforming to protection level of IP-68 flow sensor and IP-67 for transmitter and having an accuracy level of 0.5% with LED/LCD display unit. The flow meter should have the housing (flow sensor) to be made of SS 304/carbon steel with anti-corrosive protection and inside liner to be made up of hard rubber/neoprene all conforming to drinking water standards. The flow meter should be coupled with HART for data acquisition and transfer, with provision for wireless transfer through GSM. The manufacturers should have the calibration standards as per ISO-17025 and the product shall have sufficient warranty provisions. |
| 193 | OD142831/2026-2027:Supply and installation of Ultrasonic Level Transmitter for distribution EST/GSR/Sumps for Level monitoring weather protection to IP 68, Body material Die Cast Aluminium with integral / remote display. Medium -Potable Water, Max Level Range: 0 to 8 Mtr |
| 194 | OD142844/2026-2027:PH ANALYSER Transmitter Range: 0-14 pH, Power Supply 230 VAC, Input: One Digital Sensor, Output: 4-20mA HART,IP66 Protection / Tx protection cover required / Sensor Range 0-14 pH , able to transmit digitalsignal to transmitter, calibration data can be transferred to Transmitter , process temp: 65 deg |
| 195 | OD142842/2026-2027:TURBIDITY ANALYSER Providing, installation, testing and commissioning of Mixed LiquidSuspended Solid (MLSS) Analyser Range: 0.001 - 4000 NTU, Repeatability: ±5% of measuredvaue, Protection class: IP 68, Accuracy: ±1% of measured value, Output: 4 - 20 mA DC(Isolated)SOR - RUIDP 2023 - It. 43.2, Pg. 378 |
| 196 | OD142839/2026-2027:RESIDUAL CHLORINE ANALYSERTSS Analyser with Transmitter and Sensor Measuring Range: 0-10 mg/L, Accuracy: 3%,Resolution: 0.15 mg/L, Operating Temperature: 0- 40°C, Cleaning: Automatic Self-Cleaningusing compressed Air.SOR - RUIDP 2023 - It. 43.1.1, Pg. 378 |
| 197 | OD142836/2026-2027:Online Conductivity/TDS analyser- Items included: Transmitter, sensor, Flow through chamberSpecifications:Power Supply : 230 V AC ±10%, 50 Hz; Enclosure MOC: ABS;Enclosure Protection: IP 65; Temperature Range : 0 to 149.9°C;Automatic Temperature compensation; Accuracy : ± 0.01pH; Display: 4Digit, 1 inch Red LED; Calibration : 2 Point / 3 Point |
| 198 | OD142832/2026-2027:Online DO(Disolved Oxygen) Analyser- Items included: Transmitter, sensor, Flow through chamberSpecifications:Measuring Range: 0 - 20.00 mg/L (ppm); Supply Voltage: 220 VAC10%,50/60Hz; Mounting : Panel Mounted; Sensor Cable : 5 Meters; Temperature Range : 0~90°C; Resolution: 0.01 mg/L, 0.1°C; Display: 3.5-inch HD IPS colour LCD screen; Accuracy : better than ±1% or ±0.01mg/L, ±0.5°C ; Retransmission Output : 4 to 20 mA isolated;Communication Output : RS 485 MODBUS |
| 199 | OD142835/2026-2027:Supply and installation of Pressure Transmitter for distribution pipe lines pressuremonitoring, weather protection to IP 68, Body material Die Cast Aluminium withintegral / remote display. Medium - Potable Water,Max Pressure Range: 0 to 10 kg/cm2. |
| 200 | OD142845/2026-2027:Signal Survey, Design, Supply, FAT, Installation, Testing, Commissioning, SAT etc ofComplete GPRS based centralised SCADA Monitoring system using 100 mbps speed leasedline including modem and all connectivity accessories etc. |
| 201 | OD142841/2026-2027:Actuator Valves |
| 202 | OD142838/2026-2027:Design, supply and installation of Cabling(FOC, Ethernet, Power and Signal cables) |
| 203 | OD142843/2026-2027:Providing, installation, testing and commissioning of 1 KVA ONLINE UPS SYSTEM, SinglePhase 230 V, 50 Hz with 2 hour backup SMF battery bank as per specificationAt Each Sub DMA |
| 204 | OD142837/2026-2027:design ,supply and installation RTU Panel: Modular RTU complete with DI, DO, AI andmodbus communication ports and power supply 24 VDC or for variable power supply usingbatteries, rechargeable batteries, solar or 10.8 V DC to 28.8 V DC with integrated modem;connection to control center via Tele Control Basic, DNP3, IEC60870-5-104 andCommunication protocols, onboard I/Os min. (8 DI, 4 DQ, 4 AI), configuration and diagnosticsper web interface, RJ45 port, mobile communications antenna (GSM/UMTS), Mini SIM card,with adapter Micro SIM card also, data storage, GPRS (Multi-slot Class 10), 35 mm DIN railmounting, TCP/IP, DNP 3, Open VPN-Client. Panel Enclosure for Compact RTU Location,wall/floor mounted along with wiring and related accessories and arrangement of mounting ofRTU, Modem having IP-5X Protection. Panels shall be self-fabricate type only with Canopy.1. For Sub DMAS Pressure Transmitter for 7 Zones |
| 205 | OD142840/2026-2027:Supply and Installation of Control Panel with IIoT Switches & Solar panel with Battery backup,for operating Residual Chlorine Sensor for monitoring Chlorine levels at consumer end. |
| 206 | OD142833/2026-2027:Earthing Materials |
| 207 | Providing pressure sensors in Distribution line |
| 208 | OD142828/2026-2027:Supply and installation of Pressure Transmitter for distribution pipe lines pressure monitoring, weather protection to IP 68, Body material Die Cast Aluminium with integral / remote display. Medium - Potable Water, Max Pressure Range: 0 to 10 kg/cm2. |
| 209 | Providing Control valves |
| 210 | OD142830/2026-2027:Supply, Installation, Testing and Commissioning (SITC) of electrically actuated 250mm Control Valve suitable for potable water application, complete with valve body, actuator, positioner, limit switches, manual override, local control station, weatherproof control panel, mounting accessories, flanges, gaskets, bolts and nuts, dismantling joints wherever required, electrical power wiring, control cables, instrumentation cables, cable trays, conduits, junction boxes, earthing, testing, calibration, SCADA/PLC integration, commissioning, trial operation and handing over including all civil, mechanical, electrical and instrumentation accessories required for complete functioning of the system. |
| 211 | Providing Altitude Valves |
| 212 | OD142963/2026-2027:Supply, Installation, Testing and Commissioning (SITC) of hydraulically operated Altitude Valve for automatic reservoir level control complete with main valve, pilot system, sensing lines, isolation valves, strainers, fittings, dismantling joints, flanges, gaskets, bolts and nuts, support arrangements, all accessories, testing, calibration, commissioning, integration with SCADA monitoring system wherever specified, including all labour, transportation and incidental works required for complete installation and satisfactory operation |
| 213 | Providing Pressure Release Valves |
| 214 | OD142962/2026-2027:Supply, Installation, Testing and Commissioning (SITC) of hydraulically operated Pressure Release Valve for automatic control complete with main valve, pilot system, sensing lines, isolation valves, strainers, fittings, dismantling joints, flanges, gaskets, bolts and nuts, support arrangements, all accessories, testing, calibration, commissioning, integration with SCADA monitoring system wherever specified, including all labour, transportation and incidental works required for complete installation and satisfactory operation. |
| 215 | Providing Solar Panels |
| 216 | OD142920/2026-2027:Supply, Installation, Testing, and Commissioning (SITC) of a pole-mounted 20Wp Solar PV system, complete in all respects excluding civil foundation works. The scope includes:• Supply of 1 No. 20Wp high-efficiency Mono/Polycrystalline Solar PV Module (complying with IEC 61215/61730), framed in anodized aluminum with an IP65/67 junction box.• Supply of 1 No. Hot-Dip Galvanized (HDG) tubular steel pole (4-5 meters height, minimum 3mm thickness) featuring an integrated base plate and a heavy-duty customized module mounting bracket assembly designed to withstand wind speeds up to 150 km/h.• Supply of all required UV stabilized solar DC cables (Cu/XLPE), weather-resistant flexible conduits, and SS304 stainless steel hardware/anti-theft fasteners.• Installation comprising the mechanical erection, alignment, and plumbing of the pole onto a pre-existing civil foundation (foundation and anchor bolts by others), secure mounting of the PV module, and internal cable routing through the pole.• Testing & Commissioning including open-circuit voltage (\(V_{oc}\)) checks, short-circuit current (\(I_{sc}\)) verification, polarity checks, and handing over the system in a fully operational condition. |
| 217 | 2.6.1:Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge.All kinds of soil |
| 218 | 4.1.8:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:4:8 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 219 | Providing Mechanical and Electro Magnetic Flow meters |
| 220 | OD142958/2026-2027:Supplying and fitting of 80 mm dia mechanical flow meter of Woltman type confirming to ISO 4064 class B of ARAD /ZENNER/REYCHEMRPG/ITRON make and the flow meter shall be tested and certified by FCRI Palakkad.Including the cost of transportation, loading and unloading all taxes ,testing charges etc complete.. |
| 221 | OD142955/2026-2027:Supplying and fitting of 100 mm dia mechanical flow meter of Woltman type confirming to ISO 4064 class B of ARAD /ZENNER/REYCHEMRPG/ITRON make and the flow meter shall be tested and certified by FCRI Palakkad.Including the cost of transportation, loading and unloading all taxes ,testing charges etc complete.. |
| 222 | OD142960/2026-2027:Supplying and fitting of 150 mm dia mechanical flow meter of Woltman type confirming to ISO 4064 class B of ARAD /ZENNER/REYCHEMRPG/ITRON make and the flow meter shall be tested and certified by FCRI Palakkad.Including the cost of transportation, loading and unloading all taxes ,testing charges etc complete.. |
| 223 | OD142956/2026-2027:Supplying and fitting of 200 mm dia mechanical flow meter of Woltman type confirming to ISO 4064 class B of ARAD /ZENNER/REYCHEMRPG/ITRON make and the flow meter shall be tested and certified by FCRI Palakkad Including the cost of transportation, loading and unloading all taxes ,testing charges etc complete. |
| 224 | OD142957/2026-2027:Supplying an electro-magnetic flow meter of size 300mm conforming to protection level of IP-68 flow sensor and IP-67 for transmitter and having an accuracy level of 0.5% with LED/LCD display unit. The flow meter should have the housing (flow sensor) to be made of SS 304/carbon steel with anti-corrosive protection and inside liner to be made up of hard rubber/neoprene all conforming to drinking water standards. The flow meter should be coupled with HART for data acquisition and transfer, with provision for wireless transfer through GSM. The manufacturers should have the calibration standards as per ISO-17025 and the product shall have sufficient warranty provisions. |
| 225 | OD142959/2026-2027:Supplying an electro-magnetic flow meter of size 500 mm conforming to protection level of IP-68 flow sensor and IP-67 for transmitter and having an accuracy level of 0.5% with LED/LCD display unit. The flow meter should have the housing (flow sensor) to be made of SS 304/carbon steel with anti-corrosive protection and inside liner to be made up of hard rubber/neoprene all conforming to drinking water standards. The flow meter should be coupled with HART for data acquisition and transfer, with provision for wireless transfer through GSM. The manufacturers should have the calibration standards as per ISO-17025 and the product shall have sufficient warranty provisions. |
| 226 | Supplying Palm Held Machines |
| 227 | OD142846/2026-2027:Towards charges for supply and commissioning Palm held machine for meter reading inside DMA, specification of the palm held machine shall be as per KWA approved spec shall be provided after award of contract. |
| 228 | Supply and fixing Fully Automatic Vacuum Feed Gas Chlorination Plant & IIoT Controlled operating system |
| 229 | OD142964/2026-2027:Supply and Installation of 3.0 Kg / hr. Fully Automatic Vacuum Feed Gas Chlorinators and IIoT Controlled operating system with software support, Mobile Applications and Automatic Residual Chlorine sensors |
| 230 | Isolation of DMA |
| 231 | OD142954/2026-2027:Isolation of DMA for pipe line ranging from 90mm PVC to 250mm DI pipes - For isolating from other divisions and branches |
| 232 | Scada Commanding Station |
| 233 | OD142807/2026-2027:Linear Workstation - 1200L x 600D x 1200htSpecification:System Partition - 75mm thick insert type system of 1200Ht, finished with Fabric above & laminate tile below table top with one Soft Board Tile & Marker Tile. 600mm length returnpartition is also considered in between and both end of workstation. Table top - 25mm thick pre laminated particle board finished with 2mm edge banding finish.Understructure - 18mm thick Gable End fitted with suitable brackets where ever required. Wire Management - Raceway Below Table topand Skirting is considered only on Main Spine &rest with Skirting only. |
| 234 | OD142811/2026-2027:L - shaped Workstation - (1500+1500)L x 600Dx 1050ht Specification: Frames - CRCA Square Tube with size 50mm x1.6 mm thick fabricated structure and crossmembers with tube size 40 x 20 x 1.2mm thick upto a height of 725mm. Raceway - Separate metal raceway for electrical & data wiring will be provided with 75mm thickness for a height of 250mm.Privacy panel - 8mm thick laminated glass with size 1200 x 300mm having 4 side radius cutting fixed with powder coated die cast aluminium holder. Privacy panel is not considered for returnsides.Table top - 25mm thick pre laminated particle board finished with 2mm edge banding finish. |
| 235 | OD142821/2026-2027:Cabin Table - 1800L x 900D x 750ht ,Side Storage - 900L x 450D x 750htSpecification: Table top - 25mm thick pre laminated particle board finished with 2mm edge lipping finish.Understructure - 18mm thick pre laminated particle board gable end and modesty panel is considered.Wire management - Not considered Storage - Top is made of 25mm thick pre laminated particle board finished with 2mmedge lipping finish and rest all made of 18mm thick particle board with 2 nos drawers and lock. |
| 236 | OD142818/2026-2027:Cabin Table - 1500L x 750D x 750ht Side Storage - 900L x 450D x 750ht Specification: Table top - 25mm thick pre laminated particleboard finished with 2mm edge lipping finish. Understructure - 18mm thick pre laminated particle board gable end and modesty panel isconsidered. Wire management - Not considered Storage - Top is made of 25mm thick pre laminated particle board finished with 2mmedge lipping finish and rest all made of 18mm thick particle board with 2 nos drawers and lock. |
| 237 | OD142813/2026-2027:Metal keyboard tray without mousepad and with soft pad |
| 238 | OD142817/2026-2027:CPU Trolley with MS powder coated finish, made up of 0.8 mm section on the sides and 1.0mm section on the base with widthadjustment and lockable castors |
| 239 | OD142810/2026-2027:Mobile Pedestal (2D+1F) 400W x 450D x 640ht. Made of 18mm thick pre laminated particle board With 2 Drawers & 1 filing Cabinet and lock. |
| 240 | OD142814/2026-2027:High back mesh chair with syncro tilt multi locking mechanism and seat slider, head rest, lumbar support, 6 way adjustable arm rests with PU pads, and MS chrome base with castors. |
| 241 | OD142801/2026-2027:High back mesh chair with syncro tilt mechanism with single locking, adjustable lumbar support, height adjustable arm restswith PU pads and nylon base with castors. |
| 242 | OD142812/2026-2027:Medium back mesh chair with syncrotilt mechanism with single locking, adjustable lumbar support, height adjustable arm restswith PU pads and nylon base with castors. |
| 243 | OD142806/2026-2027:Medium mesh back visitor chair with fixed armrest, lumbar support and powder coated metal legs. |
| 244 | OD142815/2026-2027:Steel Cupboard for office |
| 245 | OD142820/2026-2027:Supply and fixing sound system with mic (Includes Amplifier 2 Mic, 2 Aux Inputs and CD/Stereo input (L&R), Built-in MP3 player with remote control for USB, SD/MMC card reader min 200 W out put- 2 nos. of Speakers of 200 W, each floor standing type with auxiliary connectivity technology-1 no. of Head band microphone can be connected to the amplifier directly HBM-60CC with free Maxcord brand pin. 1 no. of 98 XLR Unidirectional Dynamic Microphone corded Mic) with all connections, minimum 2 years guarantee |
| 246 | OD142805/2026-2027:Projector LCD -3600 luminous brightness minimum, with wireless, USB and HDMI connectivity with PC and other systems, resolution XGA 1024 x 768 Resolution minimum, including table top vertical tripod base, with Display white screen unit (8 x 6 Feet Tripod Projector Screen) with focus, angle change and skew correction facilities. Minimum 2 years guarantee |
| 247 | OD142819/2026-2027:All in one PC with Server Capasity of 32 GB RAM - C21GLPA HP AiO 24-cr0485in PC 24 Intel i5-1354U NA Windows 11 Microsoft Office Home & Student Edition 2024 + 1 Year M365 Basic 32GB DDR4 1TB SSD Graphics UMA , USB type C , USB type A , RJ 45 , 1 HDMI Out Wireless 24 inch Antiglare IPS & FHD IR Tiltable Camera Shell White should have 2 yrs minimum gurantee. |
| 248 | OD142808/2026-2027:Personal ComputerIntel core i3 8th gen,h310 gigabyteMb,4gb Ram,256 GB ssd,18.5? LGmonitor,Fingers cabnet,keyboard&mouse dellwarranty:3 year |
| 249 | OD142816/2026-2027:PrinterEpson 2170 black only printer Epson2170 warranty:3 year |
| 250 | OD142804/2026-2027:Colour Printer3012 colour all in oneprinter Scan ,copy, printwarranty:1 year |
| 251 | OD142822/2026-2027:Supply and Installation of 43 inches 4K Ultra HD Smart LED Google TV with all accessories should have minimum 2 years guarantee. |
| 252 | OD142803/2026-2027:Supplying and connecting 2KVA on line UPS and Supplying 12 V, 100A Batteries of 4 nos. for 2KVA on line UPS for 3 Hr Backup. Should have 2 yrs guarantee. |
| 253 | OD142802/2026-2027:Supply of Air conditioner- 1 Ton Inverter AC, 5 Star with all accessories and installation |
| 254 | OD142809/2026-2027:Supply of Ceiling Fan Sweep Size 1200 mm, Motor Type BLDC, Power Use 35 Watts, 360 RPM with all accessories and its installation |
| 255 | 13.48.1:Finishing with Deluxe Multi surface paint system for interiors and exteriors using primer as per manufacturers specifications:Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of special primer applied @ 0.75 ltr /10 sqm |
| 256 | 13.60.1:Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 257 | 13.71:Lettering with black Japan pint of approved brand and manufacture |
| 258 | 12.1.2:Providing corrugate G.S. sheet roofing including vertical/ curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead, including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete ( up to any pitch in horizontal / vertical or curved surfaces), excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.0.80 mm thick with zinc coating less than 275 gm/m2 |
| 259 | 10.2:Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 260 | 13.50.3:Applying priming coat:With ready mixed red oxide zinc chromate primer of approved brand and manufacture on steel galvanised iron /steel works |
| 261 | 13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work |
| 262 | 4.1.3:Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level:1:2:4 (cement : 2 coarse sand (zone-III)derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 263 | Road restoration- LSGD- Chipping Carpet |
| 264 | 3.5.3:Excavation in Soil using Hydraulic Excavator and Tippers with disposal upto 1000 m Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross-sections, and transporting to the embankment location with a lift upto 1.5 m and lead upto 1000 m as per Technical Specification Clause 302.3 |
| 265 | 4.1.A.1:Granular Sub-base with Well Graded Material (Table 400.1) (A) By Mix in Place Method Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. (i) For Grading I Material |
| 266 | 4.9:Wet Mix Macadam Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406. By Mechanical Means with 1 km lead |
| 267 | 5.1.1a:Prime Coat :- Low porosity Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502 |
| 268 | 5.2.3a:Tack Coat Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.30 kg per sqm on the prepared granular surfaces treated with primer & cleaned with Hydraulic broom as per Technical Specification Clause 503. |
| 269 | 5.9.1.2a:20mm thick Open-Graded Premix Carpet using Bituminous (penetration grade/modified bitumen) Binder - Bitumen S-65 Providing, laying and rolling of open-graded premix carpet of 20 mm thickness composed of 13.2 mm to 5.6 mm aggregates either using penetration grade bitumen or emulsion to required line, grade and level to serve as wearing course on a previously prepared base, including mixing in a suitable plant, laying and rolling with a three wheel 80-100 kN static roller capacity, finished to required level and grades to be followed by seal coat of either Type A or Type B or Type C as per Technical Specification Clause 508. Case - I By Manual Means (II) Bitumen (S-65) |
| 270 | 5.12.A.3.2a:Seal Coat - Manual Means - Type C - Bitumen S-65 Providing and laying seal coat sealing the voids in a bituminous surface laid to the specified levels, grade and cross fall using Type A, Type B and Type C as per Technical Specification Clause 510 A. By Manual Means :- Case - III : Type C (II) Bitumen (S-65) |
| 271 | Road restoration-PWD- BMBC |
| 272 | 3.6:Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m |
| 273 | 4.1.B.1:Construction of granular sub-base by providing graded material, spreading in uniform layers with a motor grader on a prepared surface, mixing by mix in-place method with rotavator at OMC, and compacting with a vibratory roller to achieve the desired density, complete as per clause 401. Grading-V - For sub-base cum drainage layer - Mix in Place Method |
| 274 | 4.12:Providing, laying, spreading and compacting graded stone aggregate to Wet Mix Macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density. |
| 275 | 5.1.a:Providing and applying primer coat with bitumen emulsion ( SS) on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.70 - 1.0 kg/sqm using mechanical means. |
| 276 | 5.2.a:Providing and applying tack coat with bitumen emulsion( RS) using emulsion pressure distributor at the rate of 0.20 - 0.30 kg per sqm on the prepared bituminous surface cleaned with mechanical broom. |
| 277 | 5.3.2.a:Providing and laying bituminous macadam with 80-100 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading premixed with a bituminous binder (VG 30), transported to the site, laid over a previously prepared surface with paver finisher to the required grade, level, and alignment and rolled as per clauses 501.6 and 501.7 to achieve the desired compaction For Grading II - (19 mm nominal size) |
| 278 | 5.6.2.a:Providing and laying bituminous concrete with 80-100 TPH hot mix plant producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with a bituminous binder( NRMB) @ 5.4 percent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level, and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MORTH specification clause No. 507 complete in all respects For Grading - II (13.2 mm Nominal Size) |
| 279 | Water Audit, Survey and Study of DMA after the Award of Contract |
| 280 | OD142968/2026-2027:Water Audit including Flow and Pressure assessment at various points , quality testing like residual chlorine, Turbidity, pH, report generation & assessment of NRW by identifying water losses using ultra sonic flow meters and field survey. Allmeters shall be accredited at NABL accredited labs, (DMA-wise NRW assessment, Water balance calculation (IWA methodology), Identification of apparent and real losses, Leak detection strategy and NRW reduction plan, Recommendation for NRW cell formation)-All design and Document preparation to be done separately for one DMA. All survey/design data to be submitted in forms of report/ drawings and submit in digital format also. Test Pit Excavation and Rehabilitation for measuring the pressure, quality & quantity of water at various points including road restoration. |
| 281 | OD142967/2026-2027:Creation / updating of GIS base map, Digitization of Reservoirs, feeder mains, distribution network Valves, bulk meters, pressure points, DMAs and Operational Zones , Consumer geo-coding and asset attribute database. Consumer Indexing by door to door survey of the residences, find the details of connection point length, number of family members, existing source details including quality and quantity and categorization and tracking of consumers and link to the GIS framework. (Geotagging of House Service Connections (HSCs), Identification of illegal connections Meter details and condition, Water use pattern & willingness to pay, Point load survey (institutions, commercial, bulk users),Mapping of all infrastructure on GIS platform. Creation / updating of GIS base map-Digitization of :Reservoirs, feeder mains, distribution network Valves, bulk meters, pressure points, DMAs and Operational Zones, Ward / DMA-wise population and density)-All design and Document preparation to be done separately for One DMA. All survey/design data to be submitted in forms of report/ drawings and submit in digital format also. |
| 282 | OD142965/2026-2027:Conduct Topographical survey of the proposed project area, Assess Existing system (actual hours of supply, NRW%, pressure range etc.) in consultation with KWA, Demonstrate Storage adequacy OHSR using balancing calculations, ConductEvidence-based baseline assessment while converting intermittent to 24×7 water supply, Conduct Detailed conditional assessment/ gap analysis of existing infrastructure (Intakes, Pumping Stations, WTPs, OHTs, distribution networks, tap connections etc.). Integrate existing infrastructure in proposed network, Hydraulic analysis of existing infrastructure in respect to proposed water demand etc to be done as per direction from department officers. Census data of previous decades alsorequired. Present population in proposed DMA is to be identified and population projection to be submitted with calculation (method wise population forecasting and methodology adopted for final population projection and justification also required, ) Other water demand such as domestic, institutional, commercial, firefighting, floating population etc. to be identified. determination of storage requirements, detailed condition assessment / gap analysis of existing infrastructure (intake pumpingstations, WTPs, OHTs, Distribution networks, tap connections etc required. Integration of existing infrastructure in proposed network also required. Review of existing city-level water supply system, Collection and validation of secondary datafrom ULB, Assessment of Water sources, allocation, reliability, quality, Per capita supply, coverage, pressure, continuity, Raw water mains, feeder mains, service reservoirs, Distribution network, valves, meters, SCADA, NRW / UFW status,Calculation of Service Level Benchmarks (SLBs), Condition assessment of assets, Validation of ULB-identified priority, Operational Zone / DMA and Preparation of As-Is Assessment Report also required. Overall scheme layout plan/maps of complete scheme to be prepared and provided in consultation with KWA. Detailed engineering drawings to be prepared and provided for the following such as ULB Plan with road network, reservoir Locations, hydraulic particulars of reservoirs, etc. , Reservoir command area plans , Ward plan , Flow Chart of the water supply system , Primary network plan with valve and other locations , Operational Zone plan ,DMA Plan with Distribution network, Bulk flow meters, hydraulic parameters ,Residual pressure drawing in DMA with critical control points and Detailed Hydraulic model Calculations of DMA and output. Hydraulic design to be done and submitted. Finalization of design parameters as per CPHEEO DFT Manual- Identification andfinalization of: Operational Zones; Pressure zones in 2 DMAs (size, boundaries, isolation), GIS-based hydraulic modelling (e.g., EPANET), Pipe network analysis and optimization, Nodal pressure analysis and boosting requirements, Design of:Distribution rehabilitation / replacement; Valves, PRVs, FCVs; Bulk and consumer metering. Validation of transmission mains and surge analysis. SCADA, Automation & Digital Systems- Assessment of existing automation systems, Recommendations for: SCADA architecture (DMA / city level), Flow, pressure, water quality monitoring, IoT / telemetry / digital twin solutions, Integration strategy with GIS and MIS, Capital cost estimation (SoR + market rates), O&M cost estimation, Financial feasibility analysis, Tariff analysis and cost recovery assessment, Sensitivity and sustainability analysis, All design and Documentpreparation to be done separately for one DMA. All survey/design data to be submitted in forms of report/ drawings and submit in digital format also. |
| 283 | Provision for other Items |
| 284 | OD142961/2026-2027:Provision for items not included in this bill of quantities, either fully or partially, and are covered in the scope of work of this contract, and as per specifications and special conditions laid out in this contract. |
| 285 | Cost for Maintenances (O and M cost) |
| 286 | OD143003/2026-2027:Operation and Maintenance for a period of 5 years of the system from OHSR / GLSR / DMA Boundary to consumer end, including DMA bulk meters, distribution network, valves, appurtenances, house service connections, consumer meters, SCADA / IoT instrumentation within the defined O&M boundary, water quality monitoring arrangements, NRW monitoring systems and related assets created under the Contract within such boundary, and including O&M works covered in the scope of work in this contract, and as per specifications and special conditions of this contract includes Leak rectification work in 50mm, 63mm,75mm, 90mm, 160mm uPVC (Class 2 to 6) pipeline including detecting and locating leak, earthwork excavation in all kinds of soil for exposing leak portion of the pipe including tar cutting / concrete cutting, cutting the pipe diametrically perpendicular to the axis of pipeline without causing any damages to the balance portion, dismantling and lifting the pipe from trenches, smoothening the cut ends, conveying the new pipe, cutting and lowering new pipe into the trenches, placing in position, aligning the pipe to line and level and jointing the new pipe with the existing pipe with solvent cement or repairable joint and testing the pipeline by operating the valves concerned, and rectifying the defects if noticed and refilling the trenches in layers not exceeding 20cm depth including consolidating each layers by ramming, watering, charges for removing surplus soil from work site, without causing any damage to the existing utilities, including hire for tools and plant, conveyance of tools and materials, bailing out water, providing caution boards, ribbon fencing, lighting, watching, traffic control etc., complete as per the direction of Departmental officers, including the cost of pipe & specials but excluding the cost of C.I.R. Joints; uPVC Pipes and specials shall be of good quality and conforming to relevant standards. Repairing leakage/breakage of 80mm A.C. pipeline. Rectification of joint leakages in 250mm D.I. Pipe, Replacement of faulty/ Damaged water meter, Replacement of faulty/damaged water meter with Indian Standard, Class B, Multi jet, 15mm ( 1/2), without any damage to the existing system. The meter should be replaced for any defects with in a period of 2 years. Service charges remittable to KWA for Meter testing and Meter replacement. Leak Rectification work for FTHC including all Earth work , Specials ,pipes etc complete. Supply, Conveying and fixing C. I. Double Acting Air Valve, Towards charges for Engaging Driver (as per G.O No_54_2025_Fin_Dated_19-04-2025_KS). Providing 15mm PVC Tap in the water meter assembly for 15mm ( 1/2 inch ) water connection, using 20mm ( 1/2 inch ) Indian Standard uPVC Class 6 pipes, uPVC specials and PP PN 16 Compression specials including cost of consumables, hire charges for tools and labour charges etc. complete, but excluding cost of materials and as per the direction of departmental officers. Towards fuel for running Vehicle per Month(100 litres per Month) Providing Valve Operator wherever necessary for 24*7 water supply. (First year) |
| 287 | OD143005/2026-2027:Operation and Maintenance for a period of 5 years of the system from OHSR / GLSR / DMA Boundary to consumer end, including DMA bulk meters, distribution network, valves, appurtenances, house service connections, consumer meters, SCADA / IoT instrumentation within the defined O&M boundary, water quality monitoring arrangements, NRW monitoring systems and related assets created under the Contract within such boundary, and including O&M works covered in the scope of work in this contract, and as per specifications and special conditions of this contract. Includes Leak rectification work in 50mm, 63mm,75mm, 90mm, 160mm uPVC (Class 2 to 6) pipeline including detecting and locating leak, earthwork excavation in all kinds of soil for exposing leak portion of the pipe including tar cutting / concrete cutting, cutting the pipe diametrically perpendicular to the axis of pipeline without causing any damages to the balance portion, dismantling and lifting the pipe from trenches, smoothening the cut ends, conveying the new pipe, cutting and lowering new pipe into the trenches, placing in position, aligning the pipe to line and level and jointing the new pipe with the existing pipe with solvent cement or repairable joint and testing the pipeline by operating the valves concerned, and rectifying the defects if noticed and refilling the trenches in layers not exceeding 20cm depth including consolidating each layers by ramming, watering, charges for removing surplus soil from work site, without causing any damage to the existing utilities, including hire for tools and plant, conveyance of tools and materials, bailing out water, providing caution boards, ribbon fencing, lighting, watching, traffic control etc., complete as per the direction of Departmental officers, including the cost of pipe & specials but excluding the cost of C.I.R. Joints; uPVC Pipes and specials shall be of good quality and conforming to relevant standards. Repairing leakage/breakage of 80mm A.C. pipeline. Rectification of joint leakages in 250mm D.I. Pipe, Replacement of faulty/ Damaged water meter, Replacement of faulty/damaged water meter with Indian Standard, Class B, Multijet, 15mm ( 1/2), without any damage to the existing system. The meter should be replaced for any defects with in a period of 2 years. Service charges remittable to KWA for Meter testing and Meter replacement. Leak Rectification work for FTHC including all Earth work , Specials ,pipes etc complete. Supply, Conveying and fixing C. I. Double Acting Air Valve, Towards charges for Engaging Driver (as per G.O No_54_2025_Fin_Dated_19-04-2025_KS). Providing 15mm PVC Tap in the water meter assembly for 15mm ( 1/2 inch ) water connection, using 20mm ( 1/2 inch ) Indian Standard uPVC Class 6 pipes, uPVC specials and PP PN 16 Compression specials including cost of consumables, hire charges for tools and labour charges etc. complete, but excluding cost of materials and as per the direction of departmental officers. Towards fuel for running Vehicle per Month(100 litres per Month) Providing Valve Operator wherever necessary for 24*7 water supply. (Second year) |
| 288 | OD143034/2026-2027:Operation and Maintenance for a period of 5 years of the system from OHSR / GLSR / DMA Boundary to consumer end, including DMA bulk meters, distribution network, valves, appurtenances, house service connections, consumer meters, SCADA / IoT instrumentation within the defined O&M boundary, water quality monitoring arrangements, NRW monitoring systems and related assets created under the Contract within such boundary, and including O&M works covered in the scope of work in this contract, and as per specifications and special conditions of this contract. Includes Leak rectification work in 50mm, 63mm,75mm, 90mm, 160mm uPVC (Class 2 to 6) pipeline including detecting and locating leak, earthwork excavation in all kinds of soil for exposing leak portion of the pipe including tar cutting / concrete cutting, cutting the pipe diametrically perpendicular to the axis of pipeline without causing any damages to the balance portion, dismantling and lifting the pipe from trenches, smoothening the cut ends, conveying the new pipe, cutting and lowering new pipe into the trenches, placing in position, aligning the pipe to line and level and jointing the new pipe with the existing pipe with solvent cement or repairable joint and testing the pipeline by operating the valves concerned, and rectifying the defects if noticed and refilling the trenches in layers not exceeding 20cm depth including consolidating each layers by ramming, watering, charges for removing surplus soil from work site, without causing any damage to the existing utilities, including hire for tools and plant, conveyance of tools and materials, bailing out water, providing caution boards, ribbon fencing, lighting, watching, traffic control etc., complete as per the direction of Departmental officers, including the cost of pipe & specials but excluding the cost of C.I.R. Joints; uPVC Pipes and specials shall be of good quality and conforming to relevant standards. Repairing leakage/breakage of 80mm A.C. pipeline. Rectification of joint leakages in 250mm D.I. Pipe, Replacement of faulty/ Damaged water meter, Replacement of faulty/damaged water meter with Indian Standard, Class B, Multijet, 15mm ( 1/2), without any damage to the existing system. The meter should be replaced for any defects with in a period of 2 years. Service charges remittable to KWA for Meter testing and Meter replacement. Leak Rectification work for FTHC including all Earth work , Specials ,pipes etc complete. Supply, Conveying and fixing C. I. Double Acting Air Valve, Towards charges for Engaging Driver (as per G.O No_54_2025_Fin_Dated_19-04-2025_KS). Providing 15mm PVC Tap in the water meter assembly for 15mm ( 1/2 inch ) water connection, using 20mm ( 1/2 inch ) Indian Standard uPVC Class 6 pipes, uPVC specials and PP PN 16 Compression specials including cost of consumables, hire charges for tools and labour charges etc. complete, but excluding cost of materials and as per the direction of departmental officers. Towards fuel for running Vehicle per Month(100 litres per Month) Providing Valve Operator wherever necessary for 24*7 water supply. (Third year) |
| 289 | OD143036/2026-2027:Operation and Maintenance for a period of 5 years of the system from OHSR / GLSR / DMA Boundary to consumer end, including DMA bulk meters, distribution network, valves, appurtenances, house service connections, consumer meters, SCADA / IoT instrumentation within the defined O&M boundary, water quality monitoring arrangements, NRW monitoring systems and related assets created under the Contract within such boundary, and including O&M works covered in the scope of work in this contract, and as per specifications and special conditions of this contract. Includes Leak rectification work in 50mm, 63mm,75mm, 90mm, 160mm uPVC (Class 2 to 6) pipeline including detecting and locating leak, earthwork excavation in all kinds of soil for exposing leak portion of the pipe including tar cutting / concrete cutting, cutting the pipe diametrically perpendicular to the axis of pipeline without causing any damages to the balance portion, dismantling and lifting the pipe from trenches, smoothening the cut ends, conveying the new pipe, cutting and lowering new pipe into the trenches, placing in position, aligning the pipe to line and level and jointing the new pipe with the existing pipe with solvent cement or repairable joint and testing the pipeline by operating the valves concerned, and rectifying the defects if noticed and refilling the trenches in layers not exceeding 20cm depth including consolidating each layers by ramming, watering, charges for removing surplus soil from work site, without causing any damage to the existing utilities, including hire for tools and plant, conveyance of tools and materials, bailing out water, providing caution boards, ribbon fencing, lighting, watching, traffic control etc., complete as per the direction of Departmental officers, including the cost of pipe & specials but excluding the cost of C.I.R. Joints; uPVC Pipes and specials shall be of good quality and conforming to relevant standards. Repairing leakage/breakage of 80mm A.C. pipeline. Rectification of joint leakages in 250mm D.I. Pipe, Replacement of faulty/ Damaged water meter, Replacement of faulty/damaged water meter with Indian Standard, Class B, Multijet, 15mm ( 1/2), without any damage to the existing system. The meter should be repalced for any defects with in a period of 2 years. Service charges remittable to KWA for Meter testing and Meter replacement. Leak Rectification work for FTHC including all Earth work , Specials ,pipes etc complete. Supply, Conveying and fixing C. I. Double Acting Air Valve, Towards charges for Engaging Driver (as per G.O No_54_2025_Fin_Dated_19-04-2025_KS). Providing 15mm PVC Tap in the water meter assembly for 15mm ( 1/2 inch ) water connection, using 20mm ( 1/2 inch ) Indian Standard uPVC Class 6 pipes, uPVC specials and PP PN 16 Compression specials including cost of consumables, hire charges for tools and labour charges etc. complete, but excluding cost of materials and as per the direction of departmental officers. Towards fuel for running Vehicle per Month(100 litres per Month) Providing Valve Operator wherever necessary for 24*7 water supply. (Fourth year) |
| 290 | OD143040/2026-2027:Operation and Maintenance for a period of 5 years of the system from OHSR / GLSR / DMA Boundary to consumer end, including DMA bulk meters, distribution network, valves, appurtenances, house service connections, consumer meters, SCADA / IoT instrumentation within the defined O&M boundary, water quality monitoring arrangements, NRW monitoring systems and related assets created under the Contract within such boundary, and including O&M works covered in the scope of work in this contract, and as per specifications and special conditions of this contract. Includes Leak rectification work in 50mm, 63mm,75mm, 90mm, 160mm uPVC (Class 2 to 6) pipeline including detecting and locating leak, earthwork excavation in all kinds of soil for exposing leak portion of the pipe including tar cutting / concrete cutting, cutting the pipe diametrically perpendicular to the axis of pipeline without causing any damages to the balance portion, dismantling and lifting the pipe from trenches, smoothening the cut ends, conveying the new pipe, cutting and lowering new pipe into the trenches, placing in position, aligning the pipe to line and level and jointing the new pipe with the existing pipe with solvent cement or repairable joint and testing the pipeline by operating the valves concerned, and rectifying the defects if noticed and refilling the trenches in layers not exceeding 20cm depth including consolidating each layers by ramming, watering, charges for removing surplus soil from work site, without causing any damage to the existing utilities, including hire for tools and plant, conveyance of tools and materials, bailing out water, providing caution boards, ribbon fencing, lighting, watching, traffic control etc., complete as per the direction of Departmental officers, including the cost of pipe & specials but excluding the cost of C.I.R. Joints; uPVC Pipes and specials shall be of good quality and conforming to relevant standards. Repairing leakage/breakage of 80mm A.C. pipeline. Rectification of joint leakages in 250mm D.I. Pipe, Replacement of faulty/ Damaged water meter, Replacement of faulty/damaged water meter with Indian Standard, Class B, Multijet, 15mm ( 1/2), without any damage to the existing system. The meter should be replaced for any defects with in a period of 2 years. Service charges remittable to KWA for Meter testing and Meter replacement. Leak Rectification work for FTHC including all Earth work , Specials ,pipes etc complete. Supply, Conveying and fixing C. I. Double Acting Air Valve, Towards charges for Engaging Driver (as per G.O No_54_2025_Fin_Dated_19-04-2025_KS). Providing 15mm PVC Tap in the water meter assembly for 15mm ( 1/2 inch ) water connection, using 20mm ( 1/2 inch ) Indian Standard uPVC Class 6 pipes, uPVC specials and PP PN 16 Compression specials including cost of consumables, hire charges for tools and labour charges etc. complete, but excluding cost of materials and as per the direction of departmental officers. Towards fuel for running Vehicle per Month(100 litres per Month) Providing Valve Operator wherever necessary for 24*7 water supply. (Fifth year) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 07, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Oct 23, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 5 daysOct 23, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender