Tender For annual repair & maintenance of To Nrb At Old Sectt. Dg 2026-27 (Sh: Renovation Of Pa To Honble Cms Secretary Room, Renovation Of Female Rest Room ,Improvement Of Fountain Area From Gate No 3 To 4 And Raising Of Boundary Wall Near Cm Office
Tender Value
98.84 Lakhs
Estimated cost
Bid Submission
13 Oct 2026
4 days left
EMD
1.97 Lakhs
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Delhi → Delhi
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for annual repair & maintenance of To Nrb At Old Sectt. Dg 2026-27 (Sh: Renovation Of Pa To Honble Cms Secretary Room, Renovation Of Female Rest Room ,Improvement Of Fountain Area From Gate No 3 To 4 And Raising Of Boundary Wall Near Cm Office At Delhi Vidhan Sabha ).
BOQ
| Sl. No. | Item Description |
| 1 | By Mechanical Transport including loading,unloading and stacking Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge. Note - Item to be applicable in urban areas having directions for restricted hours for movement/plying of load carrying motor vehicle of 3.5 cum or more. |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.All kinds of soil. |
| 3 | Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m: All kinds of soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia |
| 4 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 5 | Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:5:10 (1 cement : 5 coarse sand (zone-Ill) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources) |
| 6 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6(1 cement :6 coarse sand) |
| 7 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6(1 cement : 6 coarse sand) |
| 8 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4(1 cement :4 coarse sand) |
| 9 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.Granite stone slab of colour black, Cherry/Ruby red Area of slab upto 0.50 sqnn |
| 10 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.Granite stone slab of colour black, Cherry/Ruby red Area of slab over 0.50 sqm |
| 11 | Stone work (machine cut edges) for wall lining etc. (veneer work) upto 10 metre height, backing filled with a grout of average 12 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) including pointing in white cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment matching the stone shade : (To be secured to the backing and the sides by means of cramps and pins which shall be paid for separately) : Gang saw cut stone 30 mm thick Red sand stone |
| 12 | Providing and fixing stainless steel cramps of required size and shape for anchoring stone wall lining to the backing or securing adjacent stones in stone wall lining in cement mortar 1:2 (1 cement: 2 coarse sand), including making the necessary chases in stone and holes in walls wherever required. |
| 13 | Providing and fixing plywood 4 mm thick, one side decorative veneer conforming to IS: 1328 (type-1), for plain lining / cladding with necessary screws, including priming coat on unexposed surface with: Decorative veneer facings of approved manufacture |
| 14 | Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3(1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. |
| 15 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). Second class teak wood |
| 16 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 17 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 250x10 mm |
| 18 | Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 150x10 mm |
| 19 | Providing and fixing bright finished brass handles with screws etc. complete: 125 mm |
| 20 | Providing and fixing bright finished brass handles with screws etc. complete: 100 mm |
| 21 | Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. |
| 22 | Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete. |
| 23 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : 250x16 mm |
| 24 | Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and lnline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately. Note:- Structural design proof checked from a Government Engineering Institute, to be provided by the manufacturer for (i) Sites with basic wind speed > 45 m/sec as per IS 875 — Part 3 (ii) Sites with structure height more than 20m for all wind speeds Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R2 series with frame (70 mm & above) x (40 mm & above) & both glazed and fly screen sash (25 mm & above) x (50 mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre). |
| 25 | Ventilator Casement window single panel with or without fixed panel with S.S. 304 friction hinges as per size and weight of sash, single point locking zinc alloy (zannak) powder coated handles.Using R2 series with frame (39 mm & above) x (39 mm & above) & sash /mullion (39 mm & above) x (60 mm & above). (Height upto 1.2 metre) |
| 26 | Providing and fixing frame work for partitions/ wall lining etc. made of 50x50x1.6 mm hollow MS tube, placed along the walls, ceiling and floor in a grid pattern with spacing @ 60 cm centre to centre both ways (vertically & horizontally) or at required spacing near opening, with necessary welding at junctions and fixing the frame to wall/ ceiling/ floors with steel dash fasteners of 8 mm dia, 75 mm long bolt, including making provision for opening for doors, windows, electrical conduits, switch boards etc., including providing with two coats of approved steel primer etc. complete, all as per direction of Engineer-in-charge. |
| 27 | Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. |
| 28 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes |
| 29 | Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts complete. Stainless steel (grade 304) wire gauze of 0.5 mm dia wire and 1.4 mm aperture on both sides |
| 30 | Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement :4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. |
| 31 | Providing and laying Vitrified tiles in floor in diferent sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Double charge vitrified tile polished finish of size Size of Tile 600 x 1200 mm |
| 32 | Providing and laying Vitrified tiles in floor in diferent sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 600 mm |
| 33 | Providing gola 75x75 mm in cement concrete 1:2:4(1 cement :2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement: 3 fine sand) as per standard design : In 75x75 mm deep chase |
| 34 | Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. |
| 35 | Providing sand stone slab for roofing and laying them in cement mortar 1 : 4 (1 cement: 4 coarse sand) over wooden karries or R.C.C. battens or structural steel sections (Karries or battens or structural steel sections to be paid separately), including pointing the ceiling joints with cement mortar 1:3 (1 cement: 3 fine sand ) complete: Red sand stone slab 40 to 50 mm thick |
| 36 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter |
| 37 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like difusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.GI Metal Ceiling Lay in plain Tegular edge Global white color tiles of size 595x595 mm, and 0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. |
| 38 | 12 mm cement plaster of mix: 1:6 (1 cement: 6 coarse sand) |
| 39 | 15 mm cement plaster on rough side of single or half brick wall of mix: 1:6(1 cement: 6 coarse sand) |
| 40 | Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof. |
| 41 | Finishing walls with ready mixed Premium acrylic emulsion paint (Company Depot Tinted) having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade with silicon additives.New work (Two or more coats applied @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. |
| 42 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 43 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.Two coats |
| 44 | Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre |
| 45 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 46 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade: One or more coats on old work |
| 47 | Melamine polishing on wood work (one or more coat). |
| 48 | Providing and fixing double scaffolding system (cup lock type) on the exterior side, up to seven story height made with 40 mm dia M.S. tube 1.5 m centre to centre, horizontal & vertical tubes joining with cup & lock system with M.S. tubes, M.S. tube challies, M.S. clamps and M.S. staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for the required duration as approved and removing it there after. The scaffolding system shall be stiffened with bracings, runners, connection with the building etc wherever required for inspection of work at required locations with essential safety features for the workmen etc. complete as per directions and approval of Engineer-in-charge. The elevational area of the scaffolding shall be measured for payment purpose. The payment will be made once irrespective of duration of scaffolding. Note: - This item to be used for maintenance work judicially, necessary deduction for scaffolding in the existing item to be done. |
| 49 | Dismantling W.C. Pan of all sizes including disposal of dismantled materials including malba all complete as per directions of Engineer-in-Charge. |
| 50 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. Nominal concrete 1:3:6 or richer mix (including equivalent design mix) |
| 51 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. In cement mortar |
| 52 | Removing mortar from bricks and cleaning bricks including stacking within a lead of 50 m (stacks of cleaned bricks shall be measured): From brick work in cement mortar |
| 53 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below |
| 54 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm |
| 55 | Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 metres lead. |
| 56 | Dismantling barbed wire or flexible wire rope in fencing including making rolls and stacking within 50 metres lead. |
| 57 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 58 | Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as directed by Engineer- in-charge. |
| 59 | Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sq. mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately) |
| 60 | Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60 mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern. |
| 61 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.20 mm nominal dia Pipes |
| 62 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 25 mm nominal dia Pipes |
| 63 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :25 to 40 mm nominal bore |
| 64 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 65 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 66 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 67 | Grading roof for water proofing treatment with Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) |
| 68 | Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991, in true horizontal level suspended on inter-locking metal powder coated T-Grid of hot dipped galvanised iron section of 0.40 mm thick on Silhouette profile,rotary stiched double webbed white with 6 mm reveal profile (white/ black),comprising of main-T runners of size 15x42 mm of length 3000 mm, cross - T of size 15x42 mm of length 1200 mm and secondary intermediate cross-T of size 15x42 mm of length 600 mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 22x19x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall S.S screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.With 15 mm thick integral densified micro edge light weight calcium silicate false ceiling tiles |
| 69 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Clerestory windows & other Frames/ Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5 mm tolerance in dimensions i.e depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. Frame size 50 x 100 mm |
| 70 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)30 mm thick |
| 71 | Modified Estimated Cost after using correction factor on DSR 2023 on account of GST@ 0.973 (vide No. 158/SE(TAS)/GST/2024/02-E-dated 08.08.2024) |
| 72 | Add Cost index @ 4.03% |
| 73 | Providing and fixing table top wash basin(530x420x140mm) with pop up waste of standard pattern, cutting and making good the walls wherever required, complete as per direction of Engineer-in-charge.(a) Rectangle shape of make jaquar ( cat.no- JDS-WHT-25907N or equivalent in cost & specifications. |
| 74 | Providing and fixing C.P. brass bib cock with CP brass wall flange of approved make etc. all complete as per direction of Engineer-in-charge. 15 mm nominal bore. (Make Jaquar (code-OPPCHR-15037PM) or equivalent in cost & specifications. |
| 75 | Providing and fixing C.P. brass Two way angle Valve with wall flange of approved make etc. all complete as per direction of Engineer-in-charge. (Make Jaquar (code-OPP-CHR-15041PM) or equivalent in cost & specifications. (a) 15 mm nominal bore. |
| 76 | Providing and fixing C.P. brass angular stop cock / angle valve with wall flange of approved make etc. complete as per direction of Engineer-in-Charge. 15 mm nominal bore. (Make Jaquar (code-OPP-CHR-35053PM) or equivalent in cost & specifications. |
| 77 | Providing and fixing C.P. brass toilet paper roll holder with flap with CP brass flange of approved make including fixing with PVC rawl plugs & screws etc. complete as per direction of Engineer-in-Charge. Make of Jaquar Cat.-ACN-1153S or equivalent in cost & specifications. |
| 78 | Providing and fixing C.P. brass soap dispensor with CP brass flange of approved make including fixing with PVC rawl plugs & screws etc. all complete as per direction of Engineer-in-charge. (Make Jaquar (Cat.-AKP-CHR-35735P) or equivalent in cost & specifications. |
| 79 | Providing and fixing C.P. brass Hand shower (Health Faucet) having flexible tube of required length and wall hook of approved make etc. all complete as per direction of Engineer-in-charge. (Make Jaquar Cat- or equivalent in cost & specifications. |
| 80 | Providing and Fixing 32mm Click clack waste coupling of 130mm height for wash basin, Urinal of Jaquar make Code ALD-CHR-727 or qquivalent in cost & specification as per approved sample shape all complete as per direction of engineer-in-charge. |
| 81 | Providing and fixing C.P. brass towel rail 600 mm long with brackets fixed to wooden clats / rawl plugs with CP brass screws of approved make etc. complete as per direction of Engineer-in-Charge. Make Jaquar Cat.-AQN-CHR-7711 or equivalent in cost & specification. |
| 82 | Providing and fixing C.P. brass bottle trap, 32mm nominal bore of approved make etc. all complete as per direction of Engineer-in-charge. Make Jaquar Cat.-ALD-769L300x190 or equivalent in cost & specifications |
| 83 | Dismantling wall tile inclusive base plasterof all thickness fixed in cement mortar / tile adheshive including racking out joints and cleaning the surface including disposal of rubish to the designated location etc. complete as per direction of Engineer-in-charge. |
| 84 | Providing and fixing 450mm long braided hose/copper connections with two nos. nuts & rubber washers with or without nippleof approved make etc. complete as per direction of Engineer-in-Charge. Make Jaquar cat no.ALD-805B or equivalent in cost and specifications. |
| 85 | Providing and fixing white vitreous china battery based infrared sensor operated urinal of size 340 x 325 x 650 mm having pre & post flushing with water (0.75 ltr water consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge. Jaquar make model cat no URS-WHT_13263 snow white. |
| 86 | Providing and fixing Stainless steel (304 grade) floor drainer/Waste water floor drain having size 5\\"X 5\\" with stainless trap and side hole with collar of approved make and design etc.complete as per direction of Engineer-in-Charge. |
| 87 | Providing and fixing Rimless Wall Hung WC with UF slim soft close seat cover, Hinges, Accessories Set, Size: 360 x 500 x 330 mm (CNS-WHT-963UFSM) with Single Piece Slim Concealed Cistern Body with Installations Kit & “S-Type” drain pipe connection set for Wall Hung WC and Control Plate(JCP-CHR-352415)and Cistern Full Frame (JCS-WHT-2400FS) all fittings and fixtures/ model kubix series of jaguar make with all fittings and fixtures complete including cutting and making good the walls etc complete as per direction of engineer in charge. |
| 88 | Providing and fixing Urinal partition Curved 10mm of size (900x450mm) of required length and wall hook of approved make etc. all complete as per direction of Engineer-in-charge. (Make Jaquar Cat-JSE -CHR-110UC450X) or equivalent in cost & specifications. |
| 89 | Providing and Fixing Quartz Stone work (polished and machine cut) of approved make such as Haffle ,Relay, kalinga ,Miraak etc of thickness 20 mm for Washbasin Counter, backing filled with pasting araldite adhesive (1.25kg/sqm) including Edge moulding ,pointing with white cement or matching pigment with an admixture of pigment to match the Quartz shade . Quartz in any colour. Area of slab above 0.50 sqm |
| 90 | Providing and fixing Stop Cock consisting of exposed part (sleeve,lever,wall flange ) and concealed part suitable for 15mm and 20mm pipe line with inner head of jaquar make ( Exposed part SOL-CHR-6083KL and Concealed part code- ALD-CHR-083R )with sport flange or equivalent in cost & specification in cost of approved make etc. complete as per direction of Engineer-in-Charge. |
| 91 | Providing and installing prefabricated sandwich PUF panel comprising of on two faces PPGL (galvalume ) colour coated 0.5mm TCT sheet and CFC free close cell high density figid polyurethane foam of high density (40+_2kg/m3 ) having a thermal conductivity value of 0.023 w/mk and of reuired thickness sandwich between the two galvalume sheet .the outer & inner galvalume sheet of 0.50mm TCT steel 550 Mpa shall have a coating mass of 150 g/sqm zinc aluminum alloy coating total of both sides as per AS1397 and finished with 20 microns colour coating of SMP polyster quality paint as per AS/NZS-2728:1997 (category=3) over a 5 micron primer on exposed side and a back coat of 5 microns on inner side over a 5 micron primer . the panels should be required length and required width with maximum width upto 1190mm with tongue & groove configuration the prefabricated panels shall be ficced dirctly to the girth using self drilling fasteners the metal sheet shall confirm to IS 513.AS1397&2728. The polyurethane insulation shall confirm to IS 12436. The rate of the item is inclusive of all materials erectionaccessories incidental charges coast of dash fasteners etc cost of making provision for door windows, ventilators and concealed pipe conduits and support for electrial and sanitary appliance etc and other incidental charges as per sample for payment finished puf sand witch panels shall be measured upto half centimetres for claculating area upto two places of decimal no deduction shall be made for opening upto 0.20sqm and no extra payment shall be made for wastages for roof panels 50(50/80) mm thick roofing panels having finished with 0.50mm thick TCT galvalume hi-rib sheet on outer side and 0.50mm TCT plain galvalume sheet on inner side including miscellaneous expenses of fixing accessories such as dash fasteners and making arrangement for concealed conduits etc. |
| 92 | Finishing of internal walls with high class Royal Luxury Paint of Asian or equivalent paint of approved brand and manufacture Two or more coats to give an even shade etc complete as per direction of Engineer-in-Charge. |
| 93 | Providing and fixing Premium quality Glazed vitrified wall tiles polished finish of size 600x600 cm conforming to IS :15622 (thickness to be specified by the manufacturer) of approved make in all colours, shades except burgundy, bottle green, black of size as approved by Engineer -in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry+B32@ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. |
| 94 | Granite work gang saw cut (polished and machine cut) of thickness 18mm for wall lining (veneer work), backing filled with a grout of average 12 mm thick in cement mortar 1:3 (1 cement : 3 coarse sand) including pointing with white cement mortar 1:2 (1 white cement : 2 marble dust) with an admixture of pigment to match the granite shade: (To be secured to the backing by means of cramps, which shall be paid for separately). |
| 95 | Providing and fixing 6 mm thick toughened glass for UPVC window / door with EPDM rubber/neoprene gasket etc.complete as per the architectural drawing , approved brand and manufacture, as per direction of Engineer-in-charge |
| 96 | Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to existing frames including priming coat with approved steel primer all complete. |
| 97 | Providing and fixing CPVC Ball valve Long handle (CTS Socket) of approved quality (screwed end) :25 mm nominal bore |
| 98 | Providing and fixing soil,waste and vent pipes : 150 mm dia. PVC Pipe |
| 99 | Providing, supplying and fixing PVC bend of required angle/degree for 160 mm dia PVC pipe, including all fittings, jointing materials, cutting, making connections complete, as directed by the Engineer-in-Charge. |
| 100 | Providing and fixing ISI marked IS:1341 S.S Bearing hing 304 Grade pressed butt hinges bright finished with necessary screws etc.complete : Size 100 x 75x3 mm |
| 101 | Providing and fixing superior class Bright finished special quality tower bolt size 450x10 mm with necessary screws etc. complete as per approved sample and as per the direction of Engineer-in-charge. |
| 102 | Providing and fixing superior class Bright lacker finished special quality tower bolt size 250x10 mm with necessary screws etc. complete as per approved sample and as per the direction of Engineer-in-charge. |
| 103 | Providing and fixing superior class Bright lacker finished special quality tower bolt size 150x10 mm with necessary screws etc. complete as per approved sample in DVS/ drawings and as per the direction of Engineer-in-charge. |
| 104 | Providing and fixing superior class bright finished special quality brass handles with necessary screws etc., completed size of 300 x25 mm complete as per approved sample and as per the direction of Engineer - in-Charge. |
| 105 | Providing and fixing superior class bright finished special quality brass handles with necessary screws etc., completed size of 200 mm complete as per approved sample and as per the direction of Engineer - in-Charge. |
| 106 | Providing and fixing brass sliding door bolt 300 mm of Approved Quality with nuts and screws etc. complete as per the direction of Engineer-in-charge. |
| 107 | Providing and fixing factory made 25mm or required size as per direction of engineer in charge beading with colour matching of wall panelling board original quarter round moulded fixed with wooden adhesive of approved quality and screws/ nails as per direction of Engineer-in-charge. |
| 108 | Providing and fixing Fibre Reinforced Polymer (FRP) gully Cover with the frame of Size 900 x 450 mm Clear Opening (heavy duty of load bearing capacity 40 MT) process molecular binding technology & hot system etc. of approved quality & as per direction of the Engineer-in-Charge. |
| 109 | Providing and fixing Fibre Reinforced Polymer (FRP) gully Cover with the frame of Size 600 x 450 mm Clear Opening (heavy duty of load bearing capacity 40 MT) process molecular binding technology & hot system etc. of approved quality & as per direction of the Engineer-in-Charge. |
| 110 | Providing and fixing Action tesa wooden laminated flooring i/c quarter round 18mm thick of size 1900mmX18mm thick with planks of 8mm thick,600mm length & 99mm wide 8mm of AC-4 (Heringbone) of approved colour, texture and finish quality with 2mm thick PU foams as per approved colour, shade and design complete as per direction of Engineer-in-charge. |
| 111 | Providing and fixing 12 mm thick HDHMR-Plain board moisture resistance type,linned with necessary screws/nuts and bolts/nails and fixed on aluminium frame work (Aluminium frame work will be paid separtely) all complete as per direction of engineer-in-charge. |
| 112 | Providing and fixing Sheer Dimout Zebra blinds of Essence series plain cassette premium mechanism of Vista make or equivalent as per approved sampe and shade including all necessary fittings, rails,palmet etc . all complete as per manufacturer's specifications and as per the direction of Engineer-in-Charge.(Note:-Blinds Should have warranty of 1 year or more .copy of invoice & warranty documents to be submitted by the contractor .Blinds Catalogues are to be provided by the the contractor free of cost). |
| 113 | 40 mm thick gang saw cut stone flooring over 20 mm (average) thick base of cement mortar 1:5 (1 cement : 5 coarse sand) with joints 3 mm thick, side buttered with cement mortar 1:2 (1 cement : 2 stone dust) admixed with pigment to match the shade of stone and pointing with same mortar.Red Sand Stone |
| 114 | Providing edge moulding to 40 mm thick Red sand stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Red Sand Stone |
| 115 | Providing and fixing Single Lever Basin Mixer including Exposed part kit of Jaquar make(code-KUP-CHR-35233NKPM) and Concealed Body of Jaquar make(code-ALD -CHR-233N) of Single Lever Basin Mixer Wall Mountedwith 150mm extension body fixed spout without popup waste system or equivalent in cost & specification in cost of approved make etc. complete as per direction of Engineer-in-Charge. |
| 116 | Credit for Dismantled C.P Fittings |
| 117 | Credit for Dismantled M.S./Reinforement bar materials Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 4 daysOct 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 4 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender