Tender For Providing Of 04 X 125 Kva Dg Set And Allied Works At Zursar And Tasigang Under Age (I) Nyoma
Tender Value
96.35 Lakhs
Estimated cost
Bid Submission
03 Nov 2026
0 days left
EMD
1.69 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
nyoma → Jammu And Kashmir
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Providing Of 04 X 125 Kva Dg Set And Allied Works At Zursar And Tasigang Under Age (I) Nyoma
BOQ
| Sl. No. | Item Description |
| 1 | Supply, installation, testing and commissioning of diesel engine driven Generating set, self excited, self regulated, brushless AC generator of capacity 125 KVA/ 100 KW, 415 Volts, 3 Phase, 0.8 power factor, 50 Hz, 1500 RPM at NTP with silencer pipe, acoustic enclosure with sound proof canopy and sound level should be 75 DB (A) at a distance 1 Mtrs as per ISO 8528 Part-1, protected with asbetos rope independently supported from engine to outside power house up to 1 mtr, AVM pads, PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) foundation for DG set as per manufacturer's design, battery start with suitable cable for connection up to panel board. The DG set will be capable of operating in Temp range of (-) 35 degree centigrade to (+) 35 degree centigrade at an altitude of 4250 mtr above MSL complete with and including the following : (Zursar x 02 DG Set and Tasigang x 02 DG Set) |
| 2 | ALTERNATOR : Alternator rating 125 KVA (100 KW), 3 phase, 50 cycles, 415 volt, 4 wire supply, 0.8 power factor, running @ 1500 RPM self excited, self regulated, mounted on a strong fabricated steel frame, suitable for mounting on a permanent foundation 4 wire, 415 Volts, 50 cycles, 1500 RPM, self excited, self requlated, mounted on a strong fabricated steel frame suitable for mounting on a permanent foundation to be coupled with above engine. The alternator shall be conforming to BS 2613/5000 and shall be in position to generate supply with frequency regulation within ± 3% tolerance. The alternator will be suitable for tropical climate. |
| 3 | (a) Fly wheel with housing. (i) Common base frame of sturdy design suitable for anti vibration mounting and permanent concrete foundation for mounting engine and alternator as per manufacturer's instructions |
| 4 | (b) Cooling systemNaturally water cooled type (Use DAFC 50%) |
| 5 | (c) FUEL SYSTEM : Fuel injection system with fuel injector, fuel injector pump/governer electronic type fuel filter and fuel hose. |
| 6 | (d) LUR Oil SYSTEM: Lub oil pump, Electric motor driven and lub oil filter. |
| 7 | (e) AIR INTAKE SYSTEM : Air intake manifold and air cleaner dry type. |
| 8 | (f) GOVERNER : Electronic Governer |
| 9 | (g) ELECTRIC STARTING SYSTEM : Electric self starter, 24 volts DC battery (12 volt, 180 AH battery 2 Nos, Maint free charging alternator with regulator battery as per manufacturer's design, copper leads with lugs of adequate size complete with initial charging fly wheel ring and start and stop push button. |
| 10 | (h) Safe controls for Engine low lub oil pressure, high water temp, over speeding of engine and battery charging voltage display. |
| 11 | (j) GENERATOR MONITORING PANEL : Comprising of following :-(i) Micro processor based genset controller for metering, monitoring, governing and protection.(ii) Engine protection for low lub oil pressure, high coolant temperature (alarm & shutdown).(iii) Alternator protection parameters like under voltage, over current, under frequency, over frequency (alarm & shut down). |
| 12 | (k) ACCESSORIES: AVM Pads built or seperately mounted to manufacturer base frames. |
| 13 | (l) COUPLING ARRANGEMENTS : Fixed coupling. flywheel to suit fixed coupling and fly wheel housing. |
| 14 | (m) EXHAUST SYSTEM: Silencer complete with exhaust pipe of suitable size upto and Out side the building all covered with asbetos rope of suitable size all as directed. |
| 15 | (n) FUEL TANK : Daily service fuel tank of capacity suitable for 8 hours continuous operation made out of 3 mm thick (heat retardant) sheet top and bottom with caliberated level indicating arrangement, stop cock, drain plug, fuel pump of suitable capacity and connected pipe line should be installed with in built tank inside the acoustic enclosures inclusive of the cost of DG set and is as per manufacturer's design. |
| 16 | (o) ACOUSTIC ENCLOSURE : Enclosure is free standing floor mounted factory built and modular in construction to facilitate easy assembly at work site and will be drop over housing type. It will consist of acoustically treated panel housed in sheet steel will provide easy access for maintenance, repairs and operation. The enclosure is custom built to suit conditions, with the following features :-(i) Custom built product for various equipments, which ensure the optimum performance.(ii) Rugged in construction maintenance free and modular design.(iii) 16 SWG (1.6 mm) thick CRCA sheets to be used for enclosure panel to ensure longer life against weathering action. High quality acoustic insulation materials to be used for maximum sound absorption. Acoustic layers are supported by perforated sheets.(iv) Sheet metal components of the enclosure should undergo various stages of surface treatment prior to painting which leads to be better life of the enclosure against weathering action.(v) Special paint treatment with pure polyester powder / epoxy to be provided for superior weather resistance.(vi) Well designed ventilation system to be provided to pump up the heat in the chamber efficiently.(vii) For effective acoustic / weather sealing a special type weather sealing gaskets, new frame rubber gaskets to be used.(viii) Working space is to be provided around the equipment for easy maintenance / repair.(ix) Necessary cut out provision for entry and exit of fuel lines cable to be incorporated in the enclosure as per the requirement.(x) A see through transparent window (glass or acrylic) in front of engine panel to be provided for monitoring the operation. |
| 17 | In continuation of Srl item No 1.15 ......(xi) Ducting if required, bellows, mechanical hardware like locks, hinges fasteners etc. to be provided.(xii) Deliverables 75 DBA @ 1 mtr at full load under free field conditions. The temp inside the enclosure will be within as per manufacturer's recommendations above ambient temp.(xiii) The enclosure should be provided with bulk head light fitting for inside.(xiv) The battery should be placed inside the enclosure beside the DG Set on a suitable insulated platform.(xv) The DG set should be provided with external emergency stop push button.(xvi) The acoustic enclosure parts shall be of powder coated after pretreatment process. The powder coating shade should be as per manufacture's design. The base iframe should be painted with epoxy based black shade.Make for ACCOUSTIC PANEL: DG SET OEMMake of DG Set : Auth OEM OF CUMMINS /KIRLOSKAR/Mahindra |
| 18 | The following items are deemed to be included in the rate quoted for all DG sets :-(i) DHPP for testing purpose shall be supplied by the contractor without any extra charge.(ii) The contractor shall arrange for artificial load (water load) for testing for final testing of DG Set at site and the cost is deemed to be including in above offer. (iii) Testing of sound level should be carried out at the site in presence of AGE or Engr-in-Charge.(iv) One year maint spare as per manufacturer's maint schedule and as directed by Engr-in- Charge is deemed to be included in the above offer.(v) One set of latest spare part catelogue with price, exploded view of parts and user's manual are deemed to be included in the offer. Note : DG set should be testing after derating factor. |
| 19 | Supply, installation, commissioning and testing of factory made, CPRI approved LT panel of size 1.8m x 1.5m x 0.7m, outdoor type made out of CRCA sheet 3.15 mm thick, frame factory fabricated with front and back openable double door with locking arrangement, with MS angle section 50x50x6 mm support, duly powder coated painting having thickness not less than 100 microns provided suitable gasket to make it dust and vermin proof, suitable for 3 Phase, 4 wire, 415 Volts, 50 Hz, AC supply system, including copper wiring complete for all accessories, grounting the legs of panel in PCC foundation 1:4:8 platform, complete as all specified and/or as directed by Engr-in-Charge, suitable for and including the following :- (Prop Main LT Panel) |
| 20 | (i) Aluminium bus bar, 3 Phase , 4 wire , AC Supply system 50 Hz mounted on epoxy based post insulators, including drilling hole for cable connection, rating of bus bar 400 Amps - 01 Set(ii) MCCB 250 Amps, 415 Volt, 35 KA, 4 Pole, adjustable type, thermal magnetic release - 01 No for incoming(iii) MCCB 125 Amps, 415 Volt, 16 KA, 4 Pole, adjustable type, thermal magnetic release - 03 Nos for outgoing(iv) MCB 40 Amps, 415 Volt, 16 KA, 4 Pole, adjustable type, thermal magnetic release - 01 No for Local lighting(v) Indicator Lamp LED type (RYB) - 01 Set (vi) Digital type Ammeter 3 Ph with inbuilt selector switch suitable up to 300 Amp including suitable rating CTs - 01 Set(vii) Digital type Voltmeter 3 Ph with inbuilt selector switch suitable up to 500 Volt - 01 Set(viii) Timer for parallel operation of DGs, 415 Volt - 01 No(ix) S&F nature switch sensor alongwith predone switching of timer 4-8 hrs, 3 Phase 415 Volt, 3 KW - 01 No |
| 21 | Supply, installation, commissioning and testing of factory made, CPRI approved LT panel of size 1.2m x 1.2m x 0.6m, outdoor type made out of CRCA sheet 3.15 mm thick, frame factory fabricated with front and back openable double door with locking arrangement, with MS angle section 50x50x6 mm support, duly powder coated painting having thickness not less than 100 microns provided suitable gasket to make it dust and vermin proof, suitable for 3 Phase, 4 wire, 415 Volts, 50 Hz, AC supply system, grounting the legs of panel in PCC foundation 1:4:8 platform, complete as all specified and/or as directed by Engr-in-Charge, suitable for and including the following :- (Prop Sub LT Panel No 1) (Near Igloo) |
| 22 | (i) Aluminium bus bar, 3 Phase , 4 wire , AC Supply system 50 Hz mounted on epoxy based post insulators, including drilling hole for cable connection, rating of bus bar 200 Amps.(ii) MCCB 125 Amps, 415 Volt, 16 KA, 4 Pole, adjustable type, thermal magnetic release - 01 No for Incomming(iii) MCB 40 Amps, 415 Volt, 16 KA, 4 Pole, adjustable type, thermal magnetic release - 06 Nos for Outgoing(iv) Indicator lamp LED type (RYB) - 01 Set (v) Digital type Ammeter 3 Ph with inbuilt selector switch suitable upto 200 Amp including suitable rating CTs - 01 Set(vi) Digital type Voltmeter 3 Ph with inbuilt selector switch suitable upto 500 Volt - 01 Set(vii) S&F nature switch sensor alongwith predone switching of timer 4-8 hrs , 3 Phase, 415 Volt, 3 KW - 01 No(viii) Timer for parallel operation of DGs, 415 Volt - 01 No |
| 23 | Note for Ser No 2 & 3 : Drawing and Line Diagram of LT Panel Board should be approved by AGE (I) before despatch. |
| 24 | Supply and lay cable XLPE FRLS insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of following sizes :- |
| 25 | 3.5 core 150 sqmm |
| 26 | 3.5 core 70 sqmm |
| 27 | 3.5 core 50 sqmm |
| 28 | 4.0 core 25 sqmm |
| 29 | 3.5 core 25 sqmm |
| 30 | 4.0 core 16 sqmm |
| 31 | 2.0 core 16 sqmm |
| 32 | Excavation in trenches not exc. 1.5 mtr wide and not exc. 1.5 mtr in depth; for trench of cable/foundation of pole and stay etc. and getting out in hard/dense soil, complete all as specified and/or as directed by the Engr-in-Charge. |
| 33 | Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc. 25 cm in soft / loose soil, complete all as specified and/or as directed by the Engr-in-Charge. |
| 34 | Removing excavated material to a distance not exc. 50 mtr and depositing where directed at level not exc. 1.5 mtr above the starting point, complete all as specified and/or as directed by the Engr-in-Charge. |
| 35 | S&F double wall corrugated (DWC) outer pipe 40 mm and inner dia 32 mm fix complete to wall, poles etc. with suitable clamp for protection of cable, complete all as specified and/or as directed by the Engr-in-Charge. |
| 36 | S&F double wall corrugated (DWC) outer pipe 110mm and inner dia 95 mm fix complete to wall, poles etc. with suitable clamp for protection of cable, complete all as specified and/or as directed by the Engr-in-Charge. |
| 37 | S&F double wall corrugated (DWC) outer pipe 200mm and inner dia 174 mm fix complete to wall, poles etc. with suitable clamp for protection of cable, complete all as specified and/or as directed by the Engr-in-Charge. |
| 38 | M&L for earthing complete with galvanized steel earth plate electrode 60cmX60cmX6mm thick buried directly in ground, earth pit not less than 2.25m deep below normal GL with top edge of the earth plate not less than 1.25m below GL connected with earth strip 32 x 6 by means of check nuts, bolts, nuts, washers of GI or steel all as shown in plate No 3 of MES Schedule Part -1, connected to main switch board all as specified and testing on completion including provision of earth strip protected by galvanized iron 15 mm dia light grade including all excavation, earth work, PCC, RCC cover, watering by funnel etc. complete including testing on completion, complete all as specified and/or as directed by the Engr-in-Charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
TodayNov 10, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender