Tender For Construction Of Pisciculture Knowledge Centre-Cum-Superintendent Of Fisheries Office At Mohanpur, West Tripura
Tender Value
2.19 Crore
Estimated cost
Bid Submission
03 Nov 2026
26 days left
EMD
4.38 Lakhs
Bank guarantee accepted
Document Fee
8000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
tripura → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Pisciculture Knowledge Centre-Cum-Superintendent Of Fisheries Office At Mohanpur, West Tripura
BOQ
| Sl. No. | Item Description |
| 1 | Item Description |
| 2 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. 1:4 ( 1 cement : 4 fine sand ).All kinds of soil |
| 3 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.All kinds of soil |
| 4 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete. |
| 5 | Treatment of soil under plinth filling using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with sand filling:With Chlorpyriphos/Lindane E.C. 20% with 1% concentration. |
| 6 | Providing and laying dry flat brick flooring in required pattern complete. |
| 7 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering --All work upto plinth level:1:3:6 ( 1 Cement: 3 fine sand : 6 graded well burnt brickaggregate 40 mm nominal size) |
| 8 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering --All work upto plinth level:1:2:4 ( 1 Cement: 2 fine sand : 4 graded well burnt brick aggregate 40 mm nominal size) |
| 9 | Providing and laying inposition design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to site of laying but excluding the cost of centring, shuttering, finishingand reinforcement, including admixtures in recommended proportions as per IS9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per the direction of Engineer-in-Charge. (Note :- Cement content considered in this item is@ 418kg/cum. Excess/ lesscement used as per design mix is payable/recoverable separately).All works upto plinth levelReinforced cement concrete grade M-25 using 418 kg ofcement per cum |
| 10 | Providing and laying inposition design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to site of laying but excluding the cost of centring, shuttering, finishingand reinforcement, including admixtures in recommended proportions as per IS9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per the direction of Engineer-in-Charge. (Note :- Cement content considered in this item is@ 418kg/cum. Excess/ lesscement used as per design mix is payable/recoverable separately).All works upto Floor five levelReinforced cement concrete grade M-25 using 418 kg ofcement per cum |
| 11 | Centering shuttering including struttings, propping etc. and removal of form work for:Foundations, footings, bases for columns. |
| 12 | Centering shuttering including struttings, propping etc. and removal of form work for:Foundations, footings, bases for columns etc. for mass concrete with steel formwork |
| 13 | Columns, Pillars, Piers,Abutments, PostsandStrutswith M.S. shutters |
| 14 | Lintels, beams, plinth beams, girders, bressumers and cantilevers with shuttering ply |
| 15 | Weather shade, Chajjas, corbels etc., including edges. |
| 16 | Suspended floors, roofs, landings, balconies and access platform with M.S. plates and props |
| 17 | Stairs (excluding landings) except spiral-staircases withwooden plank |
| 18 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 19 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 20 | First class brick work in foundation and plinth including cost of all materials as required complete:In cement mortar 1:6 ( 1 cement : 6 fine sand ). |
| 21 | First class brick work In superstructure above plinth level & upto floor-five level including cost of all materials as required complete:In cement mortar 1:6 ( 1 cement : 6 fine sand ). |
| 22 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 23 | Neat cement punning. |
| 24 | 20 mm cement plaster of mix :Cement mortar 1:4 (1 cement : 4 fine sand) |
| 25 | 15mm cement plaster on the rough side of single or half brick wall of mix:Cement mortar 1:4 (1 cement : 4 fine sand) |
| 26 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, of approved brand and manufacture, of required shade and colour complete, as per manufacurer's specification. [Payment shall be made after submission of Test Certificate issued by the Manufacturer]New work ( two or more coats) over and including waterthinnable priming coat with cement primer. |
| 27 | Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives as per manufacturers specifications [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:New work (Two or more coats applied @ 1.43 litre/ 10sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm. |
| 28 | Providing and fixing exterior grade wood finish vitrified tile cladding of approved shade, texture and size (minimum 8-10 mm thick) on external wall surface over 12 mm thick cement plaster in CM 1:4 including backing coat, slurry, adhesive/polymer modified mortar, cutting, drilling, grooves, spacers, filling joints with matching epoxy grout, curing, scaffolding and all complete as per approved design and direction of Engineer-in-Charge. |
| 29 | Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately).White sand stone - 30mm thick gang saw cut stone |
| 30 | Providing and fixing dry cladding upto 10 metre heights with 30mm thick gang saw cut stone with (machine cut edges) of uniform colour and size upto 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc. and sealing the joints with approved weather sealant as per Architectural drawing and direction of Engineer-in-charge. (The steel frame work, stainless steel cramps and pins etc. shall be paid for separately). Red sand stone - 30mm thick gang saw cut stone |
| 31 | Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design, fixing in customize design etc. all complete as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge. |
| 32 | Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622- 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete as per direction of the Engineer-in-charge..Glazed Vitrified Tiles (Glossy / Mat Finish/ Anti-Skid) Size of tile 600 mm x 600 mm |
| 33 | Extra for providing and laying Vitrified tiles (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622- 2017, of approved make, in all colours and shades, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. all complete as per direction of the Engineer-in-charge.Soluble Salt Stainfree vitrified tiles (Glossy) / Double charged Stainfree vitrified tiles (Glossy) / Glazed Vitrified Tiles (Glossy / Mat Finish/ Anti-Skid) / Glazed Vitrified Tiles - Full Body (Glossy / Mat Finish/ Anti-Skid) |
| 34 | Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge. Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles 300 mm x 300 mm in all shades and designs |
| 35 | Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622- 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-in charge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in-charge450 mm X 300 mm in all shades and design |
| 36 | Providing and fixing Marble stone in floors over 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with white cement mixed with of matching shade, including rubbing and polishing etc. all complete as per direction of Engineer-in-charge.14 mm thick Marble stoneRaj Nagar plain marble |
| 37 | Extra for marble flooring complete in treads of steps andrisers using single length upto 2.00 metre. |
| 38 | Extra for pre-finished nosing to treads of steps of marblestone. |
| 39 | Providing and fixing hand rail using structural steel etc. of approved size by welding etc. to steel ladder railing, balcony railing and staircase railing etc. including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer complete as required:-M.S. tube |
| 40 | Providing and fixing gang saw cut of approvedthickness mirror polished, premoulded and prepolished, machine cut for kitchen platforms,vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 ( 1 cement : 4 fine sand ) with joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing , curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels:- 18 mm thick Granite of any colour and shade duly approved:-Area of slab over 0.50 sqm. |
| 41 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position :Local Teak Wood |
| 42 | Providing and fixing panelled / or panelled and glazed shutters for doors, windows and clerestory windows including ISI marked bright finished / black enamelled M.S butt hinges with necessary screws excluding panelling and or glazing, which will be paid for separately but including the wooden beading of 20 × 12 mm for fixing panelling and or glazing as per direction of Engineer-In-Charge.Local Teak wood35 mm thick shutters |
| 43 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge.(Glazing and paneling and dash fasteners to be paid for separately) :-Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 44 | For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):-Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 45 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :-With float glass panes of 8 mm thickness ( weight not less than 20 kg / sqm ) |
| 46 | Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embrossed on the body / plate with double spring mechanism and door weight upto 125 kg. for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece MS sheet outer box with slide plate etc. complete as per direction of the Engineer-in-charge:-With CP brass cover plate minimum 1.25 mm thickness |
| 47 | Filling the gap in between aluminium frame and adjacent RCC/brick work by providing weather silicon sealant over backer rod of approved quality etc. complete as per architectural drawing and direction of the Engineer-in charge:- (i) Upto 5 mm depth and 5 mm width. |
| 48 | Providing and fixing factory made uPVC white colour fixed glazed windows/ ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), , uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in- Charge. (Single / double glass panes and silicon sealant shall be paid separately). Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be madeFixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.) |
| 49 | Casement window double panels with S.S. friction hinges (300 x 19 x 1.9 mm) made of (small series) frame 47 x 50 mm, sash 47 x 68 mm & mullion 47 x 68 mm all having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area of window above 0.75 sqm upto 1.50 sqm). |
| 50 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm at 100 mm centre to centre and braced with flat iron diagonals 20x5mm size with top and bottom rail of T-iron 40x40x6mm with 40mm dia. steel pulleys & with riveted bolts, nuts, locking arrangement, stoppers, handles, hold fast /anchor bolt including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approved steel primer etc. complete as required. |
| 51 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. all complete.Fixed to openings /wooden frames with rawl plugs screws etc. |
| 52 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture. |
| 53 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications [Payment shall be made after submission of Test Certificate issued by the Manufacturer]:Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture |
| 54 | Providing and fixing ACP based decorative CNC Jali using 3 mm thick Aluminium Composite Panel, CNC router cut in approved pattern including aluminium supporting frame, edge finishing, screws, sealant and fixing arrangement complete including all materials, labour, transportation, loading-unloading and GST complete as directed by Engineer-in-Charge. |
| 55 | Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor.“(Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2)“For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.“ (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement. |
| 56 | Providing and fixing decorative vertical architectural fins/projections made with M.S. hollow tubular framework of suitable size sections, duly welded, grinded and finished with one coat red oxide primer and two coats synthetic enamel paint, clad externally with 4 mm thick exterior grade FR Aluminium Composite Panel (ACP) with PVDF coating of approved shade and make, including aluminium cleats, brackets, anchor fasteners, stainless steel screws, weather proof silicone sealant, cutting, routing, bending, scaffolding and all incidental works complete as per approved drawing and direction of Engineer-in-Charge. |
| 57 | Providing and fixing chequered terrazo tiles 22 mm thick with graded marble chips of size upto 6 mm, laid on floors, footpath & courtyard on 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with neat cement slurry mixed with pigment to match the shade of tiles including rubbing and polishing etc. all complete as per direction of Engineer-in-charge.Light shade pigment using white cement |
| 58 | 60 mm thick factory made c.c. interlocking paver block of M-35 GradeProviding and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per specifications & approval/ direction of Engineer-in-Charge.(a) 60 mm thick c.c. paver block of M-35 grade with approvedcolour, design and pattern. |
| 59 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete.Hot finished seamless type tubes |
| 60 | Providing corrugated G.S. sheet roofing including vertical/curved surface fixed with polymer coated J or L hooks, bolts and nuts 8 mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead and including a coat of approved steel primer and two coats of approved paint on overlapping of sheets complete (up to any pitch in horizontal/ vertical or curved surfaces) excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required etc. complete as per direction of Engineer-in-charge.0.80mm thick with zinc coating not less than 275gm/m2 |
| 61 | Providing and fixing 18 mm thick, 150 mm wide pelmet of coir veneer board ISI marked IS : 14842 - 2000, including top cover of 6 mm coir veneer board, nickel plated M.S. Pipe 20 mm dia (heavy type) curtain rod with nickel plated brackets including fixing with 25 × 3 mm M.S. flat 10 cm long and rawl plugs 50 mm long (designation 10 no.) etc. all complete. |
| 62 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using steel etc. complete as required:- In grating, frames, guard bar, railing, brackets, gates and similar works, all complete. |
| 63 | Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with :12.5 mm thick tapered edge gypsum moisture resistant board. |
| 64 | Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 - 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge.Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles 300 mm x 300 mm in all shades and designs |
| 65 | Extra for using veneered particle board conforming to IS 3097 Grade I, in item of pelmet 18mm thick 150mm wide. Particle board with decorative veneering on both sides. |
| 66 | Providing and fixing aluminium casement windows fastener of required length for aluminium windows with necessary screws etc. of approved quality complete as per direction of Engineer-in-charge:-16.11.1 Anodised aluminium of grade AC 15 ). |
| 67 | Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. of approved quality complete as per direction of Engineer-in-charge:-Anodised aluminium of grade AC 15 ). |
| 68 | Providing and fixing aluminium tubular handle bar of 32 mm outer dia, 3.0 mm thick and 2100 mm long with Stainless Steel screws etc. of approved quality complete as per direction of Engineer-in-charge:-Anodised aluminium of grade AC 15 ). |
| 69 | Providing and fixing 100 mm brass locks (best make of approved quality) with 6 levers without pair of handles for aluminium doors including necessary cutting and making good etc. complete as per direction of Engineerin- charge. |
| 70 | Providingandfixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :250 x 10 mm |
| 71 | Providingandfixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete :100 x 10 mm |
| 72 | Providing and fixing IS Imarked oxidised M.S.handles conforming to IS:4992 with necessary screws etc.complete :125 mm |
| 73 | Providing and fixing ISImarked oxidised M.S.handles conforming to IS:4992 with necessary screws etc.complete :100 mm |
| 74 | Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary screws etc. complete. Single rubber stopper |
| 75 | Providing and fixing bright finished brass 100mm mortice latch with one dead bolt and apair of lever handles with necessary screws etc. complete (best make of approved quality). |
| 76 | Providing and fixing IS:3564 marked Aluminium die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete. |
| 77 | BRAILLE SIGNAGE- providing and fixing multilungual Braille (raised dots) directional signage of size 150x225mm. as per accessibility standards 2 and having 3mm thick acrylic Base plate with upper case san serif words. white acrylic non glare cut out Letters of height 1smm raised not 3 less than 0.8mm above base plate and the Word written in Hindi or English non glare acrylic letters of height 15mm raised not less than 4 above base plate and having a non-glare acrylic cut out arrow pointing in the required direction. Each signboard as per manufacturers specifications on the wall at the approved location and at a height of 1200 mm from floor as per design specifications and harmonised guidelines as per the direction of the Engineer-in-charge |
| 78 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, havingthermal stabilityfor hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clampsat 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work including cutting chases and makinggood the walls etc.15 mm nominal outer dia .Pipes |
| 79 | 20 mm nominal outer dia .Pipes. |
| 80 | 25 mm nominal outer dia .Pipes |
| 81 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, havingthermal stabilityfor hot&cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling&testing of jointscompleteas per direction of Engineer in Charge. External work32 mm nominal outer dia .Pipes |
| 82 | 40 mm nominal outer dia .Pipes |
| 83 | Providing and fixing ball valve (brass) of approved quality High or low pressure, with plastic floats complete :20 mm nominal bore |
| 84 | Providing and fixing gunmetal gate valve with C.I. wheel of approved quality (screwed end):40 mm nominal bore |
| 85 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi Rigid PVC waste pipe for sink and wash basin 32 mm dia with length not less than 700 mm i/c PVC waste fittingsFlexible pipe 32 mm dia |
| 86 | Providing and fixing on wall face unplasticised Rigid PVC rain water pipes (working pressure 4 kg/cm2) conforming to IS : 13592 TypeA including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion etc. complete as per direction of Engineer-in-charge :Single socketed pipe - 110 mm OD |
| 87 | Providing and fixing on wall face unplasticised-PVC moulded fittings/ accessories for unplasticised Rigid PVCrain water pipes conforming to IS : 13592Type-A including jointing with seal ring conforming to IS : 5382 leaving10mm gap for thermal expansionetc. complete as per direction of Engineer-in-charge :Coupler 110 mm |
| 88 | Single pushfit Coupler 110 mm |
| 89 | Bend 87.5° 110mm |
| 90 | Plain shoe 110mm |
| 91 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fitting arrangement of approved quality and colour.600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms. |
| 92 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colours weighing not less than 105 gms. |
| 93 | Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.15mm nominal bore. |
| 94 | Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I.brackets, 40mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete including painting of fittings and brackets, cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid |
| 95 | Providing and Fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350mm and 340x410x265mm size respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required :One urinal basin with 5 litre white P.V.C. automatic flushing cistern |
| 96 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :White Vitreous China Wash basin size 630x450 mm with a pair of 15 mm C.P. brass pillar taps |
| 97 | Providing and laying cement concrete 1:5:10 (1 cement :5 fine sand:10 graded stone aggregate 40mmnominal size) upto haunches of S.W. pipes including bed concrete as per standard design :100 mm diameter S.W. pipe |
| 98 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 1st class bricks in cement mortar 1:4 (1 cement : 4 fine sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 fine sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design.Inside dimensions 500x700 mm and 45 cm deep for pipe line with one or two inlets : |
| 99 | Constructing soak pit 1.20 x 1.20 x 1.20 m filled with brickbats including S.W. drain pipe 100 mm diameter and 1.20 m long complete as per standard design. |
| 100 | Construction of septic tank of different capacities as per approved drawing with 1st class brick work in cement mortar (1:4) including two 560 mm dia. R.C.C. manhole cover(heavy type)of approved make supplied, fitted and fixed in the 100mm thick R.C.C (1:1.5:3) top slab with necessary fittings, 20mm thick cement plaster (4 : 1) with neat cement finish to the internal surfaces and 15 mm thick cement plaster (4 : 1) to outside wall upto 200 mm below G.L floor finished with 25 mm thick grey artificial stone over 100 mm thick R.C.C(1:1.5:3) bottom slab including supplying, fitting and fixing all necessry specials, fittings, S.W. tees, C.I. foot rest etc. including excavation earth in all sorts of soil, shoring, bailing out and pumping out water as necessary, ramming, dressing the bed and fefilling the sides of the tanks with earth, removing spoils, filling up the chamber with clear water, removing foreign materials from the chamber and including constructing attached inspection pit as per approved drawing and connecting all necessary pipes, joints etc. with internal plaster work and artificial stone flooring is to be done with admixture of water proofing compound @ 0.5% by weight of cement with all costs of labour and materials. Note:- (i) Finished level of Septic Tank should be 400 mm. from Ground Level. (ii) Height of 50 mm. Ventilation pipe &Mosquito proof mesh, should be follwed as per IS:2470,PartI.Payment will be made separetly on the basis of actual height based on relevant I.S.Code.For 30 users |
| 101 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 102 | Providing, supplying, and fixing Custom-Fabricated LED Illuminated Department Signage Board (approx. 12ft x 3ft size) displaying the name of the department . The signage shall consist of individual 3D acrylic letters (minimum 5-inch height) with internal high-brightness, weatherproof LED modules (IP67 rated). Letters shall be mounted on a powder-coated aluminum composite panel (ACP) backing plate. The unit must utilize constant-voltage LED drivers (Mean Well or equivalent) with surge protection and be suitable for 24/7 operation. Rate includes all fabrication, high-quality wiring, fixing onto the façade/wall using stainless steel fasteners, electrical connections, and 2-year onsite warranty. |
| 103 | Providing, supplying, installing, testing and commissioning of 2 HP, 230 V, 50 Hz, single-phase borewell submersible pump set, suitable for required discharge and total head, complete with submersible motor, suitable starter/control panel, required length of submersible cable, necessary GI/UPVC delivery pipe, cable joints, clamps, fittings, valves and all necessary accessories, including lowering into borewell, connection, testing and commissioning, complete in all respects as directed by the Engineer-in-Charge. |
| 104 | Supplying and installation of Switch disconnector fuse unit (main switch) of the following ratings with all accessories including necessary connection etc. as required250 amps TPN 415 volts front handle cubical main switch (HRC) |
| 105 | Supplying and installation of Bus bar chamber of the following ratings and sizes made of steel sheet enclosure with all accessories including necessary connection etc. as required300 amps 415 volts four strip Copper busbar chamber 6 ways of size (610mmx410mmx150mm) |
| 106 | Supplying and installation of powder coated steel sheet enclosure (MCB DB) suitable for 240/415 volts MCB/Isolator/RCCB (SP/SPN/DP/TP/TPN/FP) complete with necessary bus bar, neutral link, din rail, earth bar etc i/c connection as required. 4 way horizontal TPN MCB DB (Double door) |
| 107 | 6 way horizontal TPN MCB DB (Double door) |
| 108 | Supplying & installation of isolators of following ratings in the existing MCB DB including connection etc as required63 amps FP isolator |
| 109 | 40 amps DP isolator |
| 110 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)16 way , Double door |
| 111 | Supplying & installation of 10 KA breaking capacity, B/C curve MCB of following ratings in the existing MCB DB including connection as required:-6 to 32 amps SP MCB:- |
| 112 | Supplying & installation of isolators of following ratings in the existing MCB DB including connection etc as required40 amps DP isolator:- |
| 113 | Wiring for light/ fan/ exhaust fan/ call bell point with 2x1.5 sq. mm PVC insulated copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall complete with 6/10 amps modular type switch, cover plate, GI box including necessary connection etc. as required. |
| 114 | Providing and fixing of 3 pin 6/10 amps plug point with modular type 6/10 amps switch and socket including connection with 2 x 1.5 sq. mm PVC insulated Copper conductor cable (FR) on modular concealed switch board with cover plate earthing the 3rd pin etc. as required. |
| 115 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 116 | Wiring for Circuit/Sub-main with the following sizes PVC insulated Copper conductor cable (FR) in PVC conduit (medium gauge) recessed in slab/ wall etc. as required2 X 4 sq. mm + 1 X 4 sq. mm earth wire [ For AC Work ] |
| 117 | 2 X 10 + 1 X 4 sq mm [ For TPN to SPN ] |
| 118 | 2 X 1.5 + 1 X 1.5 sq mm [ for 2X6 Amp Separate Socket ] |
| 119 | 2 X 2.5 + 1 X 1.5 sq mm [ For Computer Board & 2X16 Amp separate Socket ] |
| 120 | Supplying and fixing of the following PVC conduit (medium gauge) with all accessories on slab/recessed on wall etc as required.20 mm dia |
| 121 | 32 mm dia |
| 122 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. [ Ref :- DSR-2022/Item-1.27/Page-6 ]8 Module (125mmX125mm) [ For 2X6 & 2X16 A ] |
| 123 | 12 Module (200mmX150mm) [ For Computer Board ] |
| 124 | Supplying and fixing of the following modular accessories including necessary connection etc. as required.3 pin 6/10 amps socket outlet (2M) |
| 125 | 6/10 amps one way SP switch (1M) :- |
| 126 | 3/6 pin 16/20 amps socket outlet (2M):- |
| 127 | 16/20 amps one way SP switch (1M) :- |
| 128 | Supplying and fixing of Copper terminal ends (LUGS) - long barrel of following sizes1.5 sq mm |
| 129 | 2.5 sq mm |
| 130 | 4 sq. mm |
| 131 | 6 sq. mm |
| 132 | 10 sq mm |
| 133 | 16 sq mm |
| 134 | Supply & delivery of one no. of cables of 1.1 KV grade,4 core 120 sqmm AL, XLPE Armoured ( Make -Gloster/Polycab/RR Cable/Finolex or equivalent )(NS) ( from Meter to Main Switch & Main Switch to Bus-bar) |
| 135 | Supply & delivery of one no. of cables of 1.1 KV Grade, 4 core 25 sqmm AL, XLPE Armoured ( Make - Gloster/Polycab/RR Cable/Finolex or equivalent )(NS) ( from Busbar to TPNDB ) |
| 136 | Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as requiredUpto 35 sq. mm (clamped with 1mm thick saddle) |
| 137 | Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp) |
| 138 | Supplying and laying of following sizes XLPE insulated PVC sheathed Aluminium conductor Un-armoured cable including necessary connection etc as required. [ For 50 Watt Flood Light ]2 core 6 Sq mm |
| 139 | Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required |
| 140 | Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, \\"C\\" curve including connections, painting etc. as required. [ For AC Indoor Installation ] |
| 141 | Supply and fixing of 25 A OLP 3+ AC Starter(Make: Electron) on 4 module GI board inclusive necessary connection as per direction of EIC [N.S] |
| 142 | Earthing with 40 mm dia G.I. Earth pipe (medium gauge) 4.5 m. long complete with masonry enclosure on top CI cover plate size 12\\"x 12\\" having locking arrangement including CC work, holes on earth pipe etc. as required incl Extra for using salt (5 kg) and charcoal (46kg) for pipe earth electrode as required.. |
| 143 | Providing and fixing earth bus of 50 mm X 5 mm copper strip onsurface for connections etc. as required. |
| 144 | Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required |
| 145 | Supplying and fixing call bell/ buzzer suitable for single phase,230 V, complete as required. |
| 146 | PROVIDING AND FIXING CIRCULAR/ HEXAGONAL G.I. BOX FORCEILING FAN CLAMP, OF INTERNAL DIA 140 MM, 73 MMHEIGHT, TOP LID OF 1.5 MM THICK G.I. SHEET WITH ITS TOPSURFACE HACKED FOR PROPER BONDING, TOP LID SHALL BESCREWED INTO THE G.I. BOX BY MEANS OF 3.3 MM DIA ROUNDHEADED SCREWS, ONE LOCK AT THE CORNERS. CLAMP SHALLBE MADE OF 12 MM DIA M.S. BAR BENT TO SHAPE AS PERSTANDARD DRAWING. |
| 147 | Supplying & fixing of 1200 mm sweep white color AC ceiling fan capacitor type double ball bearing complete with 300 mm down rod,canopies,shackles, 3nos blades, including wiring the down rod with 2x1.5 sqmm PVC insulated Copper conductor cable(FR) (ISI marked, BEE 1 star/minimum service value 4.0 m3/min/W) |
| 148 | Supplying & installation of 400 mm sweep AC wall mounting fan with metal blade including connection etc as required |
| 149 | Supplying and fixing of following surface/recess mounted LED luminaries in powder coated die cast housing complete with high efficiency polycarbonate diffuser and necessary connection etc. as required (with 50000 burning hours and minimum lumen output of 100 lm/watt)Surface mounted integrated 10 watt LED batten with polycarbonate diffuser |
| 150 | Supplying and fixing of following LED Tubes, retrofit bulbs/lamps for LED luminaries including necessary connection etc. as required18/20 watt LED tube with integral driver and polycarbonate diffuser (50000 burning hours and minimum lumen output of 100lm/watt):- |
| 151 | Supplying and fixing of following outdoor LED luminaries in powder coated die cast housing complete with heat resistant tempered glass/diffuser including necessary connection etc. as required (50000 burning hours and minimum lumen output of 100 lm/watt)50 watt LED flood light fixture with integral driver and secondary lens (IP 66) |
| 152 | Supplying and fixing of 15 W POST TOP (Make - Havells, Model No - RUBYMINIPT15WLED830PSYMTOPC) incl. all necessary connections. |
| 153 | Supplying and fixing of 15 W UP-down (Make - Havells, Model No - CLIOWLS15WLED830PSYMTOTG) incl. all necessary connections. |
| 154 | Supplying and fixing DP sheet steel enclosure on surface/ recessalong with 25/32 A 240 V \\"C\\" curve DP MCB complete withconnections, testing and commissioning etc. as required [ 01 No. for Post-top light, 01 No. for Street Light, and 01 No. for spare ] |
| 155 | Supplying and Fixing GI water proof looping cable box having hinged GI Top Cover having 4 mm thick with rubber gasket lining, railway type mechanical locking arrangement, earthing terminal with lug etc. of the following sizes as indicated below, Comprising of one 250 V, 15 A Kit-Kat fuse unit, one NL onporcelain insulator etc. and housing the same in pole muffing incl. addition and alteration to the existing CC muffing (6:3:1) after dismantling the damaged loopingcable box etc. wherenecy. incl. painting250 x 250 x 100mm |
| 156 | Supplying & installation of 300 mm sweep 900 rpm metalic body exhaust fan including connection etc as required (ISI marked) |
| 157 | Extra for fixing the louvers/ shutters complete with frame for aexhaust fan of all sizes. [ Ref :- DSR-2022/Item No - 1.50/Page-8 ] |
| 158 | Supplying, installation, testing and commissioning of following ratings online UPS with inbuilt isolation transformer, 50/60Hz (Auto sensing) frequency, P.F range 0.95-0.99, voltage regulation +/-1%, Pure sine wave form, total harmonic distortion <5% with full load, Noise level 50db at 1m, LED indication for Normal mode/Load on battery/Load on bypass/System fault, Audible alarm for Mains failure, low battery, Overload, fault and Bypass mode complete with M.S Rack for mounting battery bank, Battery inter link cables and all other necessary accessories including connections etc. as required:-2 kVA, 1 Ph input/1 Ph output Online UPS with 7200 VAH battery bank for minimum 2 hours Backup:- |
| 159 | Supply , Installation, Testing and Commissioning of Air Cooled Hi Wall split type Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface / concealed copper Refrigerant piping with insulation (closed cell elastomeric nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R- 407 Green Refrigerant, wireless Remote control, suitable for working between 180-260V with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of performing cooling, dehumidification, air circulation of following capacity with Scroll / rotary compressor. The system shall be able to deliver 100% of the rated capacity upto 42 Degree Celsius. Min 5 year Original Equipment Manufacturer (OEM) warranty both compressor and Printed Circuit Board (PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing control IS /International Electro technical Commission (IEC) 60730, hermetic compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS 12615. Complete as per CPWD specification and IS : 1391 Part II 2023. The system shall be able to operate up to 50 0C (out door ambient temperature). (Make:- Daikin/O-general or equivalent)2 TR with 3star or above BEE rating |
| 160 | 2.5 Tr with 3star or above BEE rating |
| 161 | Supply & Laying of soft drawn Copper pipe line with 0.6 mm or 0.7 mm (min) thick for Liquid Line and Suction Liine between ODU and IDU with fittings, elbows, bends, supports & brackets (Make-Ryoku/Hitachi/Nippon) [ For additional work as or where required ]Liquid Line 1/4\\" (6.35mm) Dia or as per manufacturer specification) |
| 162 | Gas Line/Suction Line 5/8\\" (15.88mm) Dia or as per manufacturer specification) |
| 163 | Supply & Fixing Pipe Insulation of Liquid Line and Suction Liine with 9 mm thick nitrile rubber tube also raping the insulation & copper wire with GKB Gold non adhesive raping tape (Make:- Accoflex/ Armacell/Supreme)Liquid Line 1/4\\" (6.35mm) Dia or as per manufacturer specification) |
| 164 | Gas Line/Suction Line 5/8\\" (15.88mm) Dia or as per manufacturer specification) |
| 165 | Supply and laying 4 core 2.5 sq mm control copper cable (PVC insulated & unshethed,un-armoured) from Condensing Unit to IDU control panel. (Make: Gloster/Havells/RR Kable /Finolex/ Polycab) [ For additional work as or where required ] |
| 166 | Supply and laying of Drain Water piping work out of UPVC hard pipes of following sizes incl. nitrile insulation with fiting accessories bends, elbows, tees flanges, tapings, wall sleeves hangers, supports, anchors etc. as required.(Make : Supreme / Astral/ EIC approved).25 mm dia. |
| 167 | Hiring Charge of Scafolding Arrangements for installation of all the Indoor & Outdoor Units. |
| 168 | Providing, supplying and placing Armed Chair with Colour Varnish model no. of CAWO-002 made by rubber board including transportation, loading, unloading and installation at site, complete in all respects as per manufacturer's specifications and approval of Engineer-in-Charge. |
| 169 | Supply, transport, unloading, and complete installation of 7B Chair with tubular powder-coated steel frame and moulded foam cushioning, with upholstered seat and backrest, delivered F.O.R. site, complete in all respects as per manufacturer’s specifications and approval of Engineer-in-Charge.Make: Godrej, Featherlite, Featherlite, Durian or equivalent. |
| 170 | Providing, supplying and placing Special Executive Revolving Chair – high-back ergonomic executive chair with cushioned seat and back, adjustable height, synchronized tilt mechanism, 360° swivel, fixed/adjustable armrests, heavy-duty nylon base with twin-wheel castors, finished in approved colour, complete with all standard accessories, transportation, loading, unloading and installation at site, complete in all respects as per manufacturer's specifications and approval of Engineer-in-Charge.Make: Godrej,Nilkamal Furniture,Featherlite or equivalent |
| 171 | Providing, supplying, and placing High-Back Mesh Ergonomic Office Chair – Aero High Back (or approved equivalent) with Knee-Tilt Synchro mechanism, height-adjustable arms, adjustable lumbar support, breathable mesh back, and BIFMA level 2 certification, complete with all transportation, loading, unloading, and site installation as directed by Engineer-in-Charge.Make: Godrej,Nilkamal Furniture,Featherlite or equivalent |
| 172 | Providing, supplying and placing Steel Almirah (72''x36''x18\\"), three shelves, Colour Varnish complete with all fittings, transportation, loading, unloading and installation at site, complete as approved by Engineer-in-Charge.Make: Godrej Interio,Methodex system,Delite Kom or equivalent |
| 173 | Providing, supplying and placing Premium oval Conference Table with the Size: 1200mm Diameter x 750mm Height., with oval design for equitable eye contact and spatial efficiency.Top of the table is 36mm thick high-density PLPB/MDF (IS:12823) with anti-scratch laminate and machine-pressed 2mm PVC edge-banding with Heavy-duty central hollow MS pedestal column with a heavy bottom base plate, powder-coated finish with Wire Management of 1 No. central flush-mounted flip-top Aluminium cutout box factory-fitted with: 2x 5/15A Power Sockets, 1x LAN (RJ45), and 1x HDMI port. as directed by EIC.Make: Godrej,Nilkamal Furniture,Featherlite or equivalent |
| 174 | Providing, supplying and fixing Notice Board (4'x3', 4mm glass,puporated sheet and shutter)NOTB-004, Colour Varnish transportation and installation as directed by Engineer-in-Charge. |
| 175 | Providing, supplying and placing Book Shelf with shutter manufactured by Rubber board (4'X16\\"X3') one shelf with colour varnish (Model No.- BRECK-002) as approved, complete with adjustable shelves, transportation, loading, unloading and installation, complete in all respects as per manufacturer's specifications and approval of Engineer-in-Charge. |
| 176 | Providing, supplying and placing File Rack manufactured by Rubber board (4'X16\\"X3') one shelf with colour varnish (Model No.- FRECK-002) as approved, complete with adjustable shelves, transportation, loading, unloading and installation, complete in all respects as per manufacturer's specifications and approval of Engineer-in-Charge. |
| 177 | Providing, supplying and placing Dinning Table (4'x3'), 12 mm glass top ,Natural Varnish TD4G-007, complete with transportation and installation as approved by Engineer-in-Charge. |
| 178 | Providing, supplying and placing Dining Chair with Dinning Chair, Rexine & 2\\" foam seat, Colour Varnish CDIN-002, complete with transportation and installation at site. complete in all respects as per manufacturer's specifications and approval of Engineer-in-Charge. |
| 179 | Providing, supplying and fixing Incumbency Board made of acrylic/aluminium frame with engraved name plates, complete with wall mounting accessories and installation.complete in all respects as per manufacturer's specifications and approval of Engineer-in-Charge.Make: 3M India ,Sign-D'Sign,Aludecor or equivalent |
| 180 | Providing, supplying and placing Wooden Podium (4\\"x20\\"x22\\"), Colour Varnish PAG-002 manufactured from laminated board with microphone provision, storage shelf and polished finish, complete with transportation and installation. complete in all respects as per manufacturer's specifications and approval of Engineer-in-Charge. |
| 181 | Providing, supplying and placing Computer Table Standard (L-42\\"x W-22\\"), Natural Varmish manufactured from pre-rubber board with model no. TCOM-001 complete with transportation and installation. complete in all respects as per manufacturer's specifications and approval of Engineer-in-Charge. |
| 182 | Providing, supplying and placing Full Secretariat Table (5'x3'x2.5', two drawer & two cupboard). Colcur Varnish TFS-002of approved size manufactured from pre-laminated board with drawer pedestal, keyboard tray and modesty panel, complete with transportation and installation. complete in all respects as per manufacturer's specifications and approval of Engineer-in-Charge. |
| 183 | Providing, supplying and placing Half Secretariat Table (4'x2.5'x2.5', one drawer & one cupboard), Natural Varnish THS-002, manufactured from pre-laminated board with drawer pedestal, complete with transportation and installation at site. complete in all respects as per manufacturer's specifications and approval of Engineer-in-Charge. |
| 184 | Providing, supplying and placing L shaped Executive Table ( (7 * 3.5 * 2.5) * ft with two drawers & one cupboard, Side extension 4ft (L)*16^ prime prime (W) * 2.5 * f' (H) & one rackTEX-002 Colour Varnish with side return, drawer pedestal, cable manager and laminate finish, complete with transportation and installation. complete in all respects as per manufacturer's specifications and approval of Engineer-in-Charge. |
| 185 | Providing, supplying and placing Rubber Board VIP Sofa Set Sofa Set (3 + 1 + 1) one center table, two sides table(6mm glass top),40 density foam cushion, (Woody's),Natural Varnish comprising one three-seater, two single-seater sofas and matching centre table with premium upholstery(Model No.SS56-003), complete with transportation and installation. complete in all respects as per manufacturer's specifications and approval of Engineer-in-Charge. |
| 186 | Providing, supplying, installing, testing and commissioning RO Water Purifier (Aquaguard or equivalent approved make) having minimum 10-litre storage capacity complete with accessories and plumbing connections. complete in all respects as per manufacturer's specifications and approval of Engineer-in-Charge.Make: Eureka Forbes ,Kent RO,Livepure or equivalent |
| 187 | Supply & Installation of Speech-Optimized PA System• Speakers: 4 Nos. linear PA column wall speakers (20W–30W RMS on a 100V line matching transformer) for highly intelligible vocal throw.• Amplification: 1 No. high-impedance 100V line core commercial PA booster amplifier (100W–120W output) with short-circuit protection.• Microphones: 1 No. premium 18\\" flexible condenser podium gooseneck microphone + 1 Set single handheld UHF wireless microphone kit.• Integration: 100V-rated twin-core cabling, PVC casing-capping routing, system accessories, and complete site commissioning as per EICMake: Yamaha ,JBL,Ahuja Radios or equivalent |
| 188 | Supply, Installation, Testing & Commissioning (SITC) of All-in-One Video Conferencing Bar for Huddle Room comprising an ultra-wide-angle 4K camera with electronic Pan-Tilt-Zoom (ePTZ), integrated beamforming microphone array, and premium speaker unit, complete with wall mount brackets and plug-and-play USB cabling as per technical specifications.Make: Logitech, Poly (HP), Bose Professional or equivalent |
| 189 | Supply, Installation, Testing, and Commissioning of 86\\" Interactive Flat Panel Display (IFPD)• Display: 86-inch 4K Ultra HD (3840x2160) D-LED backlight display with anti-glare, anti-fingerprint, and minimum Mohs Level-7 toughened safety glass panel.• Touch System: High-accuracy Infrared (IR) touch technology supporting minimum 40-point touch under Android and 20-point touch under Windows with a response time ≤ 6ms.• Processing Power: Built-in Android 14.0 (EDLA certified) with minimum Octa-Core CPU, 8GB RAM, 128GB ROM, and integrated dual-band Wi-Fi 6 with Bluetooth 5.2.• Audio-Visual & Ports: Inbuilt 2x20W stereo speakers, multi-microphone array, alongside front/rear connectivity including 3x HDMI In, 1x HDMI Out, Type-C (with 65W power delivery), and multiple USB 3.0 ports.• Hardware Add-ons: Includes a heavy-duty, customized wall-mount bracket, active styluses, remote control, and necessary structural wire routing accessories as directed by EIC.Make:ViewSonic,Benq,LG or Equivalent |
| 190 | Supply, Installation, Testing and Commissioning of 55\\" Smart LED Television (TV) comprising 55-inch 4K Ultra HD (3840×2160) display with D-LED backlight, HDR support, wide viewing angle and built-in smart TV platform with Wi-Fi and Bluetooth connectivity. The TV shall have a minimum refresh rate of 60 Hz, built-in stereo speakers with minimum 20 W total audio output, and connectivity including minimum 3× HDMI inputs, 2× USB ports, LAN/Ethernet, optical audio output and AV input. The unit shall be supplied complete with remote control, table-top stand/wall-mounting arrangement, power cable, necessary accessories, installation, testing and commissioning, complete in all respects as per manufacturer’s specifications and approval of Engineer-in-Charge.Make: LG, Samsung, Sony, Panasonic or equivalent approved make. |
| 191 | Supply, Installation, Testing and Commissioning of Desktop Computer Set comprising business-class desktop computer with minimum Intel Core i5 (13th Generation or latest) / AMD Ryzen 5 processor, minimum 16 GB DDR4/DDR5 RAM, 512 GB SSD, and dedicated 2 GB graphics card with suitable video memory, along with integrated Gigabit Ethernet, Wi-Fi and Bluetooth connectivity. The set shall include 21.5-inch or larger Full HD LED monitor, USB keyboard, optical/USB mouse, genuine licensed Windows operating system, necessary power cables, connectors and accessories. The complete system shall be supplied, installed, configured, tested and commissioned at site, complete in all respects as per manufacturer’s specifications and approval of Engineer-in-Charge.Graphics Card: Dedicated 2 GB graphics card, minimum suitable for professional office, CAD and multimedia applications.Make: HP, Dell, Lenovo, Acer, ASUS or equivalent approved make. |
| 192 | Supply, Installation, Testing and Commissioning of Laptop Supply, Installation, Testing and Commissioning of Laptop Computer comprising business-class laptop with minimum Intel Core i5 (13th Generation or latest) / AMD Ryzen 5 processor, minimum 16 GB DDR4/DDR5 RAM, 512 GB SSD, and dedicated 2 GB graphics card with suitable video memory. The laptop shall have a minimum 15.6-inch Full HD LED display, integrated Wi-Fi 6, Bluetooth, built-in HD webcam, integrated microphone and stereo speakers. The laptop shall be supplied with genuine licensed Windows operating system, original AC power adapter/charger, carrying bag and all necessary accessories. Complete with installation, configuration, testing and commissioning at site, as per manufacturer’s specifications and approval of Engineer-in-Charge.Graphics Card: Dedicated 2 GB graphics card suitable for professional office, CAD and multimedia applications.Make: HP, Dell, Lenovo, Acer, ASUS or equivalent approved make. |
| 193 | SITC of 2MP IP Dome Camera , Infrared 1080p FHD, Night Vision, HD Resolution, Image Sensor, Connectivity Technology: Wireless, Connectivity Protocol: RTSP, Controller Type: Android, ios, Ceiling Mount, [Detail Specifications: 1/2.7” 2MP PS CMOS Image Sensor 3.6MM Lens, 25/30 fps@ Resolutin: 1080P (1920×1080), DWDR, Day/Night(ICR), 3D-DNR, ROI, AWB, AGC, BLC, HLC, IR Range of 30 Mtrs, IP67, PoE, H.265+ / H.265 dual-stream encodingwith.] Including all fixing accessories.(Make: CP Plus/ Hikvision/ Dahua/ equivalent as per EIC choice.) |
| 194 | SITC of 2 MP + IP Bullet Camera + Night Vision Outdoor IR Camera: 30 Mtr. with 3.6mm Fixed Lens. [Detail Specifications: operating- Android and iOS , Can Be Watched Online, High Quality Branded Product, Easy to install, Night Vision : See crystal clear, black & white images even in complete darkness with Infra-Red LEDs, with CMOS Image Sensor for better and crisp picture quality, Smart IR Cut Filter, Up to 30m IR distance. including H.265+ & H.264+ dual-stream encoding, Max. 25/30fps@ Resolutin: 1080P (1920×1080) Full HD, 3.6mm fixed lens (2.8mm optional),DWDR, Day/Night(ICR), 3D-DNR, ROI, EIS, AWB, AGC, BLC, HLC,IR Range of 30 Mtrs, IP67, PoE,Mobile Software: iCMOB, gCMOB, CMS Software: KVMS Pro, Ceiling/ Wall Mount, viewing angle range: upto 84 deg, ] Including all fixing accessories. (Make: CP Plus/ Hikvision/ Dahua/ equivalent as per EIC choice.) |
| 195 | SITC of 32 Channel. H.265 4K Network Video Recorder (NVR), Industrial-grade embedded processor, [Detail Specifications: User Interface: Web; local GUI, Video Output: 1-ch VGA output and 1-ch HDMI output; simultaneous/ heterogeneous video sources output for VGA and HDMI is configurable, Resolution : 16MP; 12MP; 8MP; 5MP; 4MP; 3MP; 2MP; 720P; D1, Video Compression : H.265/Smart H.264+/H.264/MJPEG, Encode Strategy : Instastream, Video Display Split : 1st Screen: 1/4/8/9/16/25/36 ; 2nd Screen: 1/4/8/9, Audio Compression : PCM; G.711A; G.711U; G.726, Decoding Capability : AI off: 1 channel × 16MP@20fps; 1 channel × 12MP@20fps; 2 channels × 8MP@30fps; 4 channels × 5MP@30fps; 5 channels × 4MP@30fps; 10 channels × 1080p@30fps AI on: 1 channel × 16MP@20fps; 1 channel × 12MP@20fps; 2 channels × 8MP@30fps; 3 channel × 5MP@30fps; 4 channels × 4MP@30fps ; 8 channels × 1080p@30fps, Hard Disk : 4 SATA ports, up to 10 TB. The maximum HDD capacity varies with environment temperature, operating- Android and iOS, Playback: Play, pause, stop, fast forward, fast backward, rewind, play by frame, Full screen, backup (cut/file), partially enlarge, audio on/off, Ethernet: 2 RJ-45 10/100/1000 Mbps self-adaptive, Interface Ports: 1 front USB 2.0 port, 1 rear USB 3.0 port , 1 RS485, 1 RS232, Protocols: HTTP; HTTPS; TCP/IP; IPv4/IPv6; UPnP; SNMP; RTSP; UDP; SMTP; NTP; DHCP; DNS; IP Filter; PPPoE; DDNS; FTP; Alarm Server; IP Search; InstaOn; auto register; ONVIF (profile T/S/G); CGI; SDK] Including all fixing accessories. (Make: CP Plus/ Hikvision/ Dahua/ equivalent as per EIC choice.) |
| 196 | SITC of 24 port Power Over Ethernet (POE) Switches. [Detail Specifications: Provide 24x 100Mbps downlink PoE Ethernet ports, 2x gigabit uplink Ethernet ports and 1x gigabit Fiber port, Downlink Ethernet ports support PoE , each port supports max. 30W output, Support power consumption indication (LED indicates power output status), Accord with IEEE802.3 , IEEE802.3u, IEEE802. 3ab, IEEE802.3 af/at standard, 4K MAC address, 2.75Mb cache. operating- windows, Android and iOS] Including all fixing accessories. (Make: CP Plus/ Hikvision/ Dahua/ equivalent as per EIC choice.) |
| 197 | SITC of Surveillance HDD 6TB Drive HDD 3.5 inches SATA 6 Gb/s 256 MB Cache for DVR NVR Security Camera System with Drive Health Management. [Specifications: Best-Fit Applications are Network Video Recorders (NVR), Embedded Surveillance DVRs (SDVR), Hybrid Surveillance DVRs, and Surveillance DVRs, Lower power consumption means a reduction in heat emissions, which improves reliability in surveillance solutions. Tarnish-resistant components help protect drive from environmental elements, increasing field reliability,] with including all fixing accessories. minimum 7200 rpm for video storage. (Make: SEAGATE/ WESTERN DIGITAL/ HITACHI/ equivalent as per EIC choice.) |
| 198 | Supply & Laying of 6 core Fiber Optic Cable (Armoured) protected by Glass-yarn in between corrugated Steel tape & loose -tube, with Excellent Water Proof Layer & Good Moisture Resistance Suitable for Indoor / Outdoor (duct) Local Area Network System, [Specifications: Operating Temperature: -20 deg C to +60 deg C; Storage Temperature: -40 deg C to +60 deg C; Jacket Material: LSZH / HDPE; Outer Diameter: 9mm to 9.5mm +/- 0.3mm; Jacket Thickness: 1.8mm +/- 0.2mm; IEC: 60793-1/ 60794 -1-2; ISO: 11801; ITU-T: REC G.652D; Telecordia: GR-20 Core] (Make: Dlink/ Digisol/ Finolex / equivalent as per EIC choice.) |
| 199 | SITC of 108 cm (43 Inches) HD LED Monitor, Resolution: Crystal Processor 4K (3,840 x 2,160), Refresh Rate: 60 Hz; Connectivity: 2 HDMI ports to connect set top box, Blu Ray players, 1 USB ports to connect hard drives and other USB devices; Sound : 20 Watts Output, Dolby Digital Plus, Personal Computer, Screen Share, Music System, Display: LED Panel, Mega Contrast, PurColor, HD Picture Quality, Picture Quality Index- 900, Slim & Stylish Design] (Make: Samsung/ Sony/ LG/ equivalent as per EIC choice.) |
| 200 | Testing, commissioning & installation of whole CCTV system with qualified Engineer with own suitable tools as directed by EIC. |
| 201 | Supplying & Drawing LAN cable (CAT6) (Brand approved by EIC) in prelaid PVC rigid conduit/ in polythene pipe embeded in wall. (Make: Dlink/ Digisol/ Havells / equivalent as per EIC choice.)[ Ref :- DSR-2022 ] |
| 202 | Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm |
| 203 | Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 8 Module (125mmX125mm) [ For 2X6 & 2X16 A ] |
| 204 | Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required3 x 1.5 sq. mm [ for 2X6 Amp Separate Socket ] |
| 205 | 3 x 2.5 sq. mm [ For 2X16 Amp separate Socket ] |
| 206 | 2 X 10 sq. mm + 1 X 6 sq. mm earth wire [ For SPN ] |
| 207 | Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 A socket outlet |
| 208 | 5/6 A switch |
| 209 | 6 pin 15/16 A socket outlet |
| 210 | 15/16 A switch |
| 211 | Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)8 way , Double door |
| 212 | Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 Amp |
| 213 | Supplying and fixing 5 A to 32 A rating, 240 V , 10 kA, \\"C\\" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole |
| 214 | Supplying and fixing DP sheet steel enclosure on surface/ recess along with 25/32 A 240 V \\"C\\" curve DP MCB complete with connections, testing and commissioning etc. as required |
| 215 | Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.63 mm dia (OD-63 mm & ID-51 mm nominal) Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 06, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 03, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 26 daysNov 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 26 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender