Tender For special Repair To Certain Roads, Footpath And Allied Works At Gaur Enclave Under Ge (West) Lucknow.
Tender Value
69.87 Lakhs
Estimated cost
Bid Submission
02 Nov 2026
3 days left
EMD
1.29 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Lucknow → Uttar Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Certain Roads, Footpath And Allied Works At Gaur Enclave Under Ge (West) Lucknow.
Corrigendum
| Sr No | Corrigendum Date | Corrigendum | Type | New Submission Date |
|---|---|---|---|---|
| 1 | 21-Oct-2026 | Revised BOQ | BOQ | 02-Nov-2026 |
BOQ
| Sl. No. | Item Description |
| 1 | M&L for preparing existing black top surfaces by brushing with wire brushes for removing caked mud etc sweeping with broom and finally fanning the cleaned surface with gunny bags to remove all loose dirt/ dust etc and applying evenly a priming / tack coat with bituminous primer using paving bitumen VG 10@5Kg/10 sqm complete all as specified and directed. |
| 2 | M & L for bituminous premix asphaltic semi dense concrete, 30 mm (consolidated thickness) with 5.50% paving bitumen VG-30 by weight of total mix rolled and compacted to required camber and radient with automatic sensor paver and 8 to 12 tone capacity power roller to a uniform smooth surface as specified and directed by Engr-In-Charge. Note: Hot rolling to be carriedout through Tandom roller and when temparature fallen upto 60 degree centigrade rolling to be carried out through Pneumatic Tyre Roller (PTR) for filling of voids and better compaction all as specified and directed. |
| 3 | M&L for premix bitumen macadam laid / rolled and compacted to required gradient and camber (consolidated thickness 75mm or less) by using paving bitumen, any penetration @ by weight of total mix complete all as specified and directed. |
| 4 | S&F cat eyes with two way solar reflective type with 30 mm length double shank of plastic body of size 100mm x 110mm x 20mm (overall height 50 mm) and with PAMA striplens reflector and weight 164 gram fixed with special epoxy chemical as per manufactures instructions. |
| 5 | Supply and fixing aluminium-alloy body Solar stud with following specification:-(a) Solar panel Mono-Crystalline Solar 2.4V/0 3 Watt and having charging capacity at a very low sunlight.(b) Red colour Six Super Bright LEDs with 10000 to 18000 mcd (Millicandela) 8 mm fitted at appropriate height for clear blinking point.(c) 1.2V Ni-MH or Ni-CD rechargeable battery capacity 1300 mAh. LSD (Low Self Discharge technology) fitted inside solar stud.(d) Working time 3 to 4 days successively after the battery is fully charged.(e) Charging time for full charge One full sunny day.(f) Working temperature: 10 to 75 Degree Celcius.(g) Flash rate 60 to 70 times per minute normally.(h) Brightness sensitive auto-switch, automatically turns on at dusk and turns off at dawn to ensure easy and safe night driving(i) High visibility LEDs help ensure easy and safe night driving from a distance of 1000-1100 Meters approx.(k) Solar stud should be free of maintenance and operational in all weather conditions.(i) The PCB board and solar panel should be sealed in Poly Carbonate case for extra waterproofing and high/low temperature protection. The logo of the manufacturer should be embossed on front side of the body to ensure genuinesess.Dimension/Size of the Solar Std should be 125 mmx125mmx25 mm body, with shank height 65 mm (Total height 90 mm including shank)(m) Weight of the Solar Stud should be 650 Gram approx.(n) Minimum 150 gram of a special epoxy chemical should be used per pcs to fix the stud on the road surface. |
| 6 | Providing and applying 2.5 mm thick road marking strips not exc 15 cm width with 250 gram Glass Beads (retroreflective) of specified shade/colour using hot thermoplastic material by fully/semi-automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoes heater, driven by experoenced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dier, seals, oil, grease and foreign material etc, complete as per direction and accordance with applicable specifidactions as per MoRTH specification having Titatnium -12%, Resin-19% & Intermix Glass Beads - 34% in proportion. |
| 7 | Providing and applying 2.5 mm thick road marking strips with 250 gram Glass Beads(retroreflective) of specified shade/colour using hot thermoplastic material by fully/semi-automatic thermoplastic paint applicator machine fitted with profile shoe, glass beads dispenser, propane tank heater and profile shoes heater, driven by experoenced operator on road surface including cost of material, labour, T&P, cleaning the road surface of all dier, seals, oil, grease and foreign material etc, complete as per direction and accordance with applicable specifidactions as per MoRTH specification having Titatnium -12%, Resin-19% & Intermix Glass Beads 34% in proportion. |
| 8 | Demolition of cement concrete (unreinforced) in ground floors and pavings not exc 15cm thick (below or above ground level) complete all as specified and directed. |
| 9 | M & L for 50 mm thick PCC 1:4:8, type D2( using 40mm graded stone aggrtegate) as in sub base etc complete all as specified and directed. |
| 10 | S&F 150mm dia medium grade tubes with all fittings and laid in trenches or in floors complete all as specified and directed. |
| 11 | S & F one 3-seater outdoor garden bench matching the design and quality of the reference picture. The bench must have a heavy-duty cast iron frame with rust resistant coating and seat/back support made using a minimum of 8 FRP (Fibre Reinforced Plastic) wooden finish strip suitable for outdoor use. The bench shall be measure approximately 125-140 cm in length, 40-50 cm seat height from ground, and 45-55 depth. The total weight of the bench must be between 50kg to ensure to durability and stability and all fastening hardware shall be stainless steel or equivalent corrosion - resistant material. The bench must be weather proof, Water proof, UV resistant and free from sharp edges, structural defects, cracks, rust or visible manufacturing flaws at the time delivery complete all as specified and directed by Engr-In-Charge. |
| 12 | S & F in repair solar integral AIO Post-top luminaire with solid polycarbonate housing, reliable & robust construction with IP65 protection, suitable for pole entry dia of 60mm, having Min3000 system lumens suitable for 12 hours (Dim mode) Autonomy lightining mode selectable for 2H/4H/6Halong with the CCT 3000K/4000K/6500K by remote. Lithium Pherrophosphate Battery capacity min 14.4 Ah @ 3.2V. Panel capacity min 13 Wp. CRI>=70, system Efficacy > 165Lm/W & system wattage should not be more than 18W+ 2%, if wattages increases then the size of battery & panel shall also be increased in similar percentage to maintain equal autonomy of the system. Microwave Motion Sensor 5.8GHz<=25mW. Life class of LED System 25000hrs @ L70 LED Make: CREE/NICHIA/LUMILEDS/OSRAM. CE Certified, charger efficiency>90%. The PV module should be made up of crystalline silicon solar cells \\"Mono-Crystalline\\" and must have a certificate of testing concirming to IEC 61215 Edition-II/BIS 14286 & IEC 61370-1,2 IEC 60598, Operating temp 0 degree centigrate to 55 degree Centigrate, certifying above given parameters all reports shall be from in house NABL or IECQ or any international accredited Laboratory including fixing of pole with nut and bolt and bolt grout with PCC column size 45cm x 45cm x 50cm complete all as specified and directed by Engr-In-Charge |
| 13 | M&L for preparation of Old or Previously untreated brick, stone, concrete or plastered surfaces of any description specifically for background paint for writting letters, not otherwise described and applying two coats of synthetic enamel paint, etc complete all as specified and directed by Engr -in- charge. Please Enable Macros to View BoQ information |
| 14 | M&L for preparation of Old or Previously untreated brick, stone, concrete or plastered surfaces of any description specifically for background paint for writting letters, not otherwise described and applying two coats of synthetic enamel paint, etc complete all as specified and directed by Engr -in- charge. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 21, 2026
11:30 IST
Tender Published
Tender notice published.
Completed
Nov 02, 2026
18:00 IST
Corrigendum-1 Issued
Clarifications on tender conditions and amendments issued.
Upcoming · 3 daysNov 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 3 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender