Tender For Provision Of Certain Minor Works At Technical And Domestic Area Under Age (I) Af Amritsar

Sharing tender

Tender For Provision Of Certain Minor Works At Technical And Domestic Area Under Age (I) Af Amritsar- 1 Cutting Out Bricks, Forming Toothing For, And Bonding New Into Old Work In Cement Mortar 1:4 Including Value Of New Materials Entering Old Walls And Jointing And Pointing (Measured On Vertical Face In Contact With Old Wall Only) Complete All As Specified And Directed . 2 M&L Brick Work With Sub-Class B Bricks, Straight Or Curved On Plan To Any Radius In Half Brick Thk Walls Built In Cm 1:4 Complete All As Specified And As Directed. 3 M&L 15Mm Thick Cement Plastering In Cm 1:6 On Brick Or Concrete Surfaces Other Than Fair Surface, Finished The Surfaces Even And Smooth Without Using Extra Cement Including Taking Down Complete All As Specified And Directed By Engr-In-Charge 4 Material And Labour For Preparation Of New Plastered Surfaces Of Walls And Applying Two Coats Of 1St Quality Acrylic Distemper(Ready Mixed) Havingvoc Content Less Than 50Gms/Litre Over And Including 1Mm Thick Birla/Jk Wall Care Putty To Obtain Smooth Regular/Even Finish Over A Coat Of Primer, Complete All As Specified And Directed. 5 M&L Rcc (Nominal Mix) Type B-1 1:2:4 Using 20Mm Graded Aggregate In Roof Slabs Supported On Walls, Beams And Columns Etc./Complete All As Specified And As Directed By Engr-In-Charge. 6 Material And Labour For Formwork To Sides And Soffits Of Roof Beams, Lintels, Cantilever, Shelves, Splay Between Floor And Beam Etc., Flat Fair Finished Concrete Surfaces, Complete All As Specified And Directed. 7 S&F Mild Steel Tmt Bars 10Mm Dia And Over Cut To Length Bent To Shape Reqd, Incl Cranking Bending Spirally For Hooping For Col,Hooking Ends And Binding With And Incl Ms Wire (Annealed) Not Less Than 0.9 Mm Dia Or Securing With Clips Qty Confirming To Fe-410W(Gde- E-250) Or Fe-290(Gde-E-165) Complete All As Specified And As Directed. 8 M&L Framed Work Such As Grills, Gratings , Etc With Ends Of Bars Shouldered And/Or Riveted, Or Forged Into Spikes; Framed Gaurd Bars;Barred Iron Doors ;Ladders; Framed Balusters;Walk Ways;Railings; Frameworks Of Water Tanks And Similar Work Conforming To Fe 290.Gde-E-165 For Portions Framed And Hung As Gates , Including Hand Made Sliding Bolts Etc In Doors Or Gates Of Angle Or Other Section With Gusset Plates, Rails, Braces, Etc., Fixing Complete All As Specified And Directed By Eic. 9 Providing And Fixing Factory Made Single Extruded Wpc (Wood Polymer Composite) Solid Plain/Decorative Type Flush Door Shutter Of Size 30Mm Thick Comprising Of Virgin Polymer Of K Value 58-60 (Suspension Grade), Calcium Carbonate And Natural Fibers (Wood Powder/ Rice Husk/Wheat Husk) And Non Toxic Additives (Maximum Toxicity Index Of 12 For 100 Gms) Having Minimum Density Of 650 Kg/Cum And Screw Withdrawal Strength Of 1800 N (Face) & 900 N (Edge), Minimum Compressive Strength 50 N/Mm2 , Modulus Of Elasticity 850 N/Mm2 And Resistance To Spread Of Flame Of Class A Category With Property Of Being Termite/Borer Proof, Water/Moisture Complete All As Specfied And Directed By Engr-In-Charge . 10 S&F 250 Mm Isi Marked In Size Aluminium Alloy, Anodised, Sliding Door Bolt With Hasp, Staple(Bolt Type) With Bright Bolt Not Less Than 12 Mm Dia With And Including A Minimum Of 6 Bolts And Nuts, Four On Bolt Plate And Two On Staple Plate Complete And Fixing Clips Of Sheet Cast Or Extruded Sections And Fixed Complete All As Specified And As Directed. 11 S&F 100 Mm Isi Marked In Size Butt Hinges Extruded Aluminium Alloy With Galvanised Mild Steel Hinges Pin, Anodised And Fixed Type B-21 Complete All As Specified And As Directed. 12 S&F 150 Mm Isi Marked In Size Aluminium Alloy Handles , Anodised, Fabricated Type, Anodised Complete All As Specified And As Directed. 13 M&L For Two Coat Synthetic Enamel Paint Over A Coat Red Oxide Primer On New Steel Surface Of Any Description Over 10 Cm Width Or Girth Not Otherwise Described Including Prepration Of Surface Complete All As Specified And Directed 14 M&L For Demolition Of Cement Concrete In Any Position And Any Description Complete All As Specified And Directed By Engr-In-Charge. 15 M & L For 40 Mm Thick Pcc 1:2:4 Type B-1 (Using 20 Mm Graded Stone Aggregate) As In Flooring , Finishing Cement Concrete Surface Even And Smooth Complete All As Specified And Directed By Engr-In-Charge. 16 M&L For Cutting Holes In Brick Walls In Cement Mortars Exc. Half Brick Not Exc One Brick For Inserting Hold Fasts Of Doors/Windows Etc And Making Good Dismantled Portion In Cm 1:3 Or Cement Mortar 1:2:4 Type B-1 All As Specified And Directed By Engineer In Charge . 17 M&L Framed Work Such As Grills, Gratings , Etc With Ends Of Bars Shouldered And/Or Riveted, Or Forged Into Spikes; Framed Gaurd Bars;Barred Iron Doors ;Ladders; Framed Balusters;Walk Ways;Railings; Frameworks Of Water Tanks And Similar Work Conforming To Fe 290.Gde-E-165 For Portions Framed And Hung As Gates , Including Hand Made Sliding Bolts Etc In Doors Or Gates Of Angle Or Other Section With Gusset Plates, Rails, Braces, Etc., Fixing Complete All As Specified And Directed By Eic. 18 M&L For Two Coat Synthetic Enamel Paint Over A Coat Red Oxide Primer On New Steel Surface Of Any Description Over 10 Cm Width Or Girth Not Otherwise Described Including Prepration Of Surface Complete All As Specified And Directed 19 Material And Labour For Preparation Of New Plastered Surfaces Of Walls And Applying Two Coats Of 1St Quality Acrylic Distemper(Ready Mixed) Havingvoc Content Less Than 50Gms/Litre Over And Including 1Mm Thick Birla/Jk Wall Care Putty To Obtain Smooth Regular/Even Finish Over A Coat Of Primer, Complete All As Specified And Directed. 20 Surface Excavation N.Exc (Not Exceeding) 30 Cm Deep And Averaging 15Cm Deep And Getting Out In Soft & Loose Soil. 21 M&L For Excavating In Trenches, N Exc 1.5 M Wide And N Exc 1.5 M In Depth; For Foundation, Etc. Or For Shafts, Wells, Cesspits,Manholes, Pier Holes, Etc. Nexc 10 Sq M On Plan And N Exc 1.5 M In Depth And Getting Out All As Specified And Directed. 22 M&L For Removal Of Excavated Material Exc. 500M Upto Distance Of 1.5 Km And Depositing All As Specified And Directed. 23 Demolition Of Cement Concrete (Unreinforced) In Ground Floors And Pavings Not Excceding 15Cm Thickness (Above Or Below Ground Level) All As Specified. 24 M&L Pcc 1:2:4 Type B-2 Using 40 Mm Graded Crushed Stone Aggr As In Foundation, Filling And Mass Concrete To Be Laid In Alternate Bays All As Specified And Directed By Engineer In Charge. 25 M&L Pcc 1:5:10 Type E-2 Using 40Mm Graded Crushed Stone Aggr As In Sub Base/Foundation All As Specified And Directed By Engineer In Charge. 26 M&L, Brick Work With Sub Class B Bricks, Straight Or Curved On Plan Exc 6 M Mean Radius Built In Cm 1:4 Complete All As Specified And As Directed. 27 M&L Rendering 15 Mm Thick In Cm 1:4 On Fair Faces Of Brick Work Or Concrete Surfaces Incl Wpc, Finished Even And Smooth Without Using Extra Cement All As Specified And As Directed. 28 M&L For Preparing New Plastered Surface And Applying Two Coats Of Whitewash On Plastered Surface Of Ceiling, Walls All Specified And Directed By Engr-In-Charge. 29 Excavating In Post Holes( Or Similar Holes) Each N Exc 0.5 Cu.M. Getting Out And Removing Surplus Soil To A Distance N.Exc 50 M And Making Good Surface Complete All As Specified And Directed By Eic. 30 M & L For Pcc (1:3:6) Type C-2 With Using 40Mm Graded Stone Aggregate As In Foundation, Filling And Mass Concrete All As Specified And Directed 31 M&L Ms Plate(Plain Or Chequred)Channels,Square Cut Or Notched (Ordinary And Counter Sunk)Forming Holes, Without Any Attachment Also Fastening And Fixing Completeall As Specified And Directed By Eic. 32 S&F Mild Steel Bolts Purpose Made With Hexagonal Or Square Head One End And Screwed The Other , Or Screwed Both Ends; Each Screwed End To Be Fitted With Washers And One Hexagonal Nut Exc. 30 Cm Long , Having Dia Not Exc 12Mm All As Specified And Directed By Eic . 33 S&F Pre-Painted Galvatume Aluminum Zinc Coating Gi Based Corrugated Steel Sheet 0.50Mm Thick Of Any Pattern Having Tensile Strength Of 550 Mpa As In Roof Covering/ Cladding To Wall, Fixed With Self Tapping Screws As Specified. 34 S&F Steel Work In Tubular Trusses Including Special Shaped Washer Etc. Complete Using Erw Or Induction Butt Welded Tubes Conforming To I.S 1161-1979 Grade St. 240 All As Specified And Directed By Eic. 35 M&L For Two Coat Synthetic Enamel Paint Over A Coat Red Oxide Primer On New Steel Surface Of Any Description Over 10 Cm Width Or Girth Not Otherwise Described Including Prepration Of Surface Complete All As Specified And Directed By Engineer-In-Charge. 36 M&L Framed Work Such As Grills, Gratings , Etc With Ends Of Bars Shouldered And/Or Riveted, Or Forged Into Spikes; Framed Gaurd Bars;Barred Iron Doors ;Ladders; Framed Balusters;Walk Ways;Railings; Frameworks Of Water Tanks And Similar Work Conforming To Fe 290.Gde-E-165 For Portions Framed And Hung As Gates , Including Hand Made Sliding Bolts Etc In Doors Or Gates Of Angle Or Other Section With Gusset Plates, Rails, Braces, Etc., Fixing Complete All As Specified And Directed By Eic