Defence Statutory Bodies & Commissions/Committees Closing in 19 days TDR #57878843

Tender For Special Repair To Armoury At 503 Su Under Ge (Af) Gurgaon

Issued by Statutory Bodies & Commissions/Committees · Gurgaon, Haryana
Tender Value
42.93 Lakhs
Estimated cost
Bid Submission
26 Oct 2026
19 days left
EMD
88000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online

Tender Overview

Competition Type
NCB
Bidding Type
Tender
Location / State
Gurgaon → Haryana
EMD Exemption
Not Available
Quantity
Not Available

Project Description

Tender For Special Repair To Armoury At 503 Su Under Ge (Af) Gurgaon- 1 Demolition Of Brick Work Or Rubbled Stone Masonry Including All Quoins Arches , Pillars Etc Built In Cement Mortar And Including Removal From The Site Complete All As Specified. 2 M&L For Brick Work With Sub Class B Old Size Brick, Straight Or Curved On Plan Exc 6.0 Mtr Mean Radius Built In Cement Mortar 1:6 Etc Complete All As Specified. 3 Taking Down Cement Plaster On Brick Or Stone Walls, Etc. Including Raking Out Joints, Hacking For Key, Scrubbing Down With Water, Etc And Including Removal Of Debris And Rubbish From The Site Complete All As Specified. 4 Demolition Of Cement Concrete (Un-Reinforced) In Ground Floors And Pavings N Exc 15 Cm Thickness (Below Or Above Ground Level) Complete All As Specified. 5 M&L Rendering 15 Mm Thick On Brick Or Concrete Surfaces In Cement Mortar (1:4) Finished Fair And Even And Using Wpc, Complete All As Specified And Directed (Note : Wpc Shall Be Measured And Paid Separately. 6 M&L Rendering 15 Mm Thick On Brick Or Concrete Surfaces In Cement Mortar (1:6) Finished Even And Smooth Without Using Extra Cement, Complete All As Specified. 7 M&L Rendering 10 Mm Thick In Cement Mortar (1:3), As On Concrete Surfaces (Such As Top & Sides Of Chajjas, Beams, Balcony Ceiling Etc.) Finished Even And Smooth Without Using Extra Cement, Complete All As Specified. 8 M&L Preparing Of New Surface Of Wall And Applying Two Coats Of Exterior Emulsion Paint Over A Coat Primer On Walls Complete All As Specified And Directed By Engineer-In-Charge. Complete All As Specified And As Directed By Engineer-In-Charge . 9 M & L Preparation Of Newly Plastered Wall Surfaces Of Wall And Applying Two Coats Of Obd Over A Coat Of Chalk Whiting Putty Including Preparation Of Surfaces On Walls As Specified And Directed . 10 M&L For Preparation Of Newly Plastered Or Unplastered/Undecorated Surface Of Ceiling And Applying Two Coats Of Oil Bound Distemper Over One Coat Of Chalk Whiting Putty Complete All As Specified 11 M&L For Preparation Of Plastered Or Unplastered Old Decorated Surfaces By Complete Removal Of Existing Treatment By Mechanised Sander Of Berger Paints Or Equivalent Makes Viz Xpress Sanding Machine Having Suction Vaccum Bag Or By Manual Scrapping Tools Where Mechanical Removal Is Not Possible And Filling Of Holes And Cracks With With Suitable Material Like Cement Or Plaster Of Paris Etc And Thereafter Applying Two Coat Of Oil Bound Distemper On Walls. Note : (A) Stage For Preparation Of Surfaces Shall Be Got Approved From Engg-In-Charge Before Applying The Finishes.(B) Material Shall Be Procured From Manufacturer. 12 All As Per Item No.11 Here-In-Before But On Surfaces Of Ceiling. 13 M&L For Preparation(Complete Removal Of Existing Treatment) Of Old Decorated External Wall/Ceiling/Rppf Surface Of Existing Treatment By Scrapping With Trucare Wall Sander : L-01/H-01 (Having Mechanical Vaccum Mechanism) Having Rpm Not Less Than 1500, Sand Pad Of 80 Grit Having Dia Of 7\/9\ To Make The Surface Free From Dust, Loose Paint Etc Or Equivalent Makes Viz Xpress Sanding Machine Having Suction Vaccum Bag Or By Manual Scrapping Tools Where Mechanical Removal Is Not Possible And Applying Two Coats Of Wheather Proofing Exterior Acrylic Emulsion Paint Over Priming Coat Premium Quality On Wall/Roof Surface Upto 4Th Storey Buildings Complete All As Specified And Directed. Note : (A) Stage For Preparation Of Surfaces Shall Be Got Approved From Engg-In-Charge Before Applying The Finishes.(B) Material Shall Be Procured From Manufacturer And Work Shall Be Got Executed Through Authorised Applicator. 14 Pressed Steel Frames Made Out Mild Steel Sheet 1.25 Mm Thick, With Size Of Frame 125 Mm X 60 Mm For Doors With One Or More Rebates Including Necessary Fixing Lugs, Hinges, Lock Strike Plates Etc And Applying A Shop Coat Of Red Oxide Primer Including Providing Pcc 1:3 :6 Type C-0 Using 12.5 Mm Graded Crush Stone Aggregate For Filling Back Of Chowkhats Complete All As Specified And As Directed By The Engineer-In-Charge 15 Pressed Steel Frames Made Out Mild Steel Sheet 1.25 Mm Thick, With Size Of Frame 105 Mm X 60 Mm For Doors With One Or More Rebates Including Necessary Fixing Lugs, Hinges, Lock Strike Plates Etc And Applying A Shop Coat Of Red Oxide Primer Including Providing Pcc 1:3 :6 Type C-0 Using 12.5 Mm Graded Crush Stone Aggregate For Filling Back Of Chowkhats Complete All As Specified And As Directed By The Engineer-In-Charge 16 S & F 35Mm Thick 2Nd Class Hard Wood Glazed And Skeleton Shutters, Open Rebated And Prepared To Receive Glass, Gauze Etc. (Without Sash Bars), Edges Of Framing Plain, Chamfered Or Rounded, Fitted With Cut And Mitred Beads For Securing Glass, Etc.; Size Of Members Of Shutters As Specified In Ssr Part – I, Section – 8, Clause 8.20 (A) ; Supplied And Fitted To Chowkats All As Specified And Directed By Engineer - In - Charge 17 S & F Flush Shutter 35 Mm Thick Solid Core Construction With Block Board Core And Plywood Face Panels Commercial Type On Both Sides With Lipping / Frame To Match All As Specified And Directed By Engineer - In - Charge. 18 S & Faluminium Alloy, Anodised With Bright Bolt And Fixed, Length Of Bolt 200Mm Long All As Specified And Directed By Engineer - In – Charge . 19 S&F 300Mm Aluminium Alloy, Anodised,Sliding Door Bolt With Hasp, Staple (Bolt Type) And Fixing Clips Of Sheet, Cast Or Extruded Sections And Fixing Bolts And Sliding Bolts Of Extruded Sections Or Cast-Aluminium Alloy And Fixed 20 S & F Aluminium Handle Cast Type Anodised, 125 Mm Long All As Specified And Directed By Engineer - In - Charge . 21 S & F Stainless Steel Butt Hinges, Medium Weight 100Mm Size All As Specified And Directed By Engineer - In - Charge . 22 M&L For Providing Plain Cement Concrete (1:2:4) Type B0 (Using 12.5 Mm Graded Crushed Stone Aggregate) As In Coping Or Roof Kerbs On Roof Chamfered On Edge Including Trowelling Slightly Complete All As Specified. 23 Supply Only Intergral Water Proofing Compound Isi Marked Complete All As Specified. 24 Taking Down Chowkats Or Frames With Shutters (Without Taking Off Shutter From Frames) Not Exc. 1.5 Sqm Each, Including Cutting Holes For Removing The Hold Fast Etc (Distrubed Surface Of Wall Shall Be Make Good By The Contractor. The Rate Quoted Shall Be Deemed Included For The Same) Complete All As Specified. 25 Taking Down Chowkats Or Frames With Shutters (Without Taking Off Shutter From Frames) Exc. 1.5 Sqm But N Exc 4 Sqm Each, Including Cutting Holes For Removing The Hold Fast Etc (Distrubed Surface Of Wall Shall Be Make Good By The Contractor. The Rate Quoted Shall Be Deemed Included For The Same) Complete All As Specified. 26 Dismantling/Removing Old Damaged Worn Out App Of Any Thickness Incl Screed Bed Or Plastering Of Any Thickness And Removing The Rubish Materials Outside Mod Land At A Dumping Place Earmarked Marked By Any State Govt/Municipalities Etc Any Distance Complete All As Specified And As Directed.

BOQ

Name of Work:- Special repair to Armoury at 503 SU under GE (AF) Gurgaon
Sl. No. Item Description
1Demolition of brick work or rubbled stone masonry including all quoins arches , pillars etc built in cement mortar and including removal from the site complete all as specified.
2M&L for brick work with sub class 'B' old size brick, straight or curved on plan exc 6.0 mtr mean radius built in cement mortar 1:6 etc complete all as specified.
3Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site complete all as specified.
4Demolition of cement concrete (un-reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified.
5M&L Rendering 15 mm thick on brick or concrete surfaces in cement mortar (1:4) finished fair and even and using WPC, complete all as specified and directed (Note : WPC shall be measured and paid separately.
6M&L Rendering 15 mm thick on brick or concrete surfaces in cement mortar (1:6) finished even and smooth without using extra cement, complete all as specified.
7M&L Rendering 10 mm thick in cement mortar (1:3), as on concrete surfaces (such as top & sides of chajjas, beams, balcony ceiling etc.) finished even and smooth without using extra cement, complete all as specified.
8M&L Preparing of new surface of wall and applying two coats of exterior emulsion paint over a coat primer on walls complete all as specified and directed by Engineer-in-charge. complete all as specified and as directed by Engineer-in-Charge .
9M & L preparation of newly plastered wall surfaces of wall and applying two coats of OBD over a coat of chalk whiting putty including preparation of surfaces on walls as specified and directed .
10M&L for preparation of newly plastered or unplastered/undecorated surface of ceiling and applying two coats of oil bound distemper over one coat of chalk whiting putty complete all as specified
11M&L for preparation of plastered or unplastered old decorated surfaces by complete removal of existing treatment by mechanised sander of berger paints or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and filling of holes and cracks with with suitable material like cement or plaster of paris etc and thereafter applying two coat of oil bound distemper on walls. Note : (a) Stage for Preparation of surfaces shall be got approved from Engg-In-Charge before applying the finishes.(b) Material shall be procured from manufacturer.
12All as per item No.11 here-in-before but on surfaces of ceiling.
13M&L for preparation(complete removal of existing treatment) of old decorated external wall/ceiling/rppf surface of existing treatment by scrapping with Trucare Wall Sander : L-01/H-01 (having mechanical vaccum mechanism) having RPM not less than 1500, sand pad of 80 grit having dia of 7\\"/9\\" to make the surface free from dust, loose paint etc or equivalent makes viz Xpress sanding machine having suction vaccum bag or by manual scrapping tools where mechanical removal is not possible and applying Two coats of wheather proofing exterior acrylic emulsion paint over priming coat premium quality on wall/roof surface upto 4th storey buildings complete all as specified and directed. Note : (a) Stage for Preparation of surfaces shall be got approved from Engg-In-Charge before applying the finishes.(b) Material shall be procured from manufacturer and work shall be got executed through authorised applicator.
14Pressed steel frames made out mild steel sheet 1.25 mm thick, with size of frame 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc and applying a shop coat of red oxide primer including providing PCC 1:3 :6 type C-0 using 12.5 mm graded crush stone aggregate for filling back of chowkhats complete all as specified and as directed by the Engineer-in-Charge
15Pressed steel frames made out mild steel sheet 1.25 mm thick, with size of frame 105 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plates etc and applying a shop coat of red oxide primer including providing PCC 1:3 :6 type C-0 using 12.5 mm graded crush stone aggregate for filling back of chowkhats complete all as specified and as directed by the Engineer-in-Charge
16S & F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc.; size of members of shutters as specified in SSR Part – I, Section – 8, clause 8.20 (a) ; supplied and fitted to chowkats all as specified and directed by Engineer - in - Charge
17S & F flush shutter 35 mm thick solid core construction with block board core and plywood face panels commercial type on both sides with lipping / frame to match all as specified and directed by Engineer - in - Charge.
18S & FAluminium alloy, anodised with bright bolt and fixed, length of bolt 200mm long all as specified and directed by Engineer - in – Charge .
19S&F 300mm Aluminium alloy, anodised,sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed
20S & F aluminium handle cast type anodised, 125 mm long all as specified and directed by Engineer - in - Charge .
21S & F Stainless Steel butt hinges, medium weight 100mm size all as specified and directed by Engineer - in - Charge .
22M&L for providing plain cement concrete (1:2:4) type B0 (using 12.5 mm graded crushed stone aggregate) as in coping or roof kerbs on roof chamfered on edge including trowelling slightly complete all as specified.
23Supply only intergral water proofing compound ISI Marked complete all as specified.
24Taking down chowkats or frames with shutters (without taking off shutter from frames) not exc. 1.5 sqm each, including cutting holes for removing the hold fast etc (Distrubed surface of wall shall be make good by the contractor. The rate quoted shall be deemed included for the same) complete all as specified.
25Taking down chowkats or frames with shutters (without taking off shutter from frames) exc. 1.5 Sqm but n exc 4 Sqm each, including cutting holes for removing the hold fast etc (Distrubed surface of wall shall be make good by the contractor. The rate quoted shall be deemed included for the same) complete all as specified.
26Dismantling/removing old damaged worn out APP of any thickness incl screed bed or plastering of any thickness and removing the rubish materials outside MOD land at a dumping place earmarked marked by any state govt/municipalities etc any distance complete all as specified and as directed. Please Enable Macros to View BoQ information
27Dismantling/removing old damaged worn out APP of any thickness incl screed bed or plastering of any thickness and removing the rubish materials outside MOD land at a dumping place earmarked marked by any state govt/municipalities etc any distance complete all as specified and as directed. Please Enable Macros to View BoQ information

AI Tender Summary

OUR REF NO 57878843
AUTHORITY Statutory Bodies & Commissions/Committees
TENDER VALUE 42.93 Lakhs
LAST DATE 26-10-2026
Authority
Authority Name Military Engineer Services
Work Description Tender For Special Repair To Armoury At 503 Su Under Ge (Af) Gurgaon- 1 Demolition Of Brick Work Or Rubbled Stone Masonry Including All Quoins Arches , Pillars Etc Built In Cement Mortar And Including Removal From The Site Complete All As Specified. 2 M&L For Brick Work With Sub Class B Old Size Brick, Straight Or Curved On Plan Exc 6.0 Mtr Mean Radius Built In Cement Mortar 1:6 Etc Complete All As Specified. 3 Taking Down Cement Plaster On Brick Or Stone Walls, Etc. Including Raking Out Joints, Hacking For Key, Scrubbing Down With Water, Etc And Including Removal Of Debris And Rubbish From The Site Complete All As Specified. 4 Demolition Of Cement Concrete (Un-Reinforced) In Ground Floors And Pavings N Exc 15 Cm Thickness (Below Or Above Ground Level) Complete All As Specified. 5 M&L Rendering 15 Mm Thick On Brick Or Concrete Surfaces In Cement Mortar (1:4) Finished Fair And Even And Using Wpc, Complete All As Specified And Directed (Note : Wpc Shall Be Measured And Paid Separately. 6 M&L Rendering 15 Mm Thick On Brick Or Concrete Surfaces In Cement Mortar (1:6) Finished Even And Smooth Without Using Extra Cement, Complete All As Specified. 7 M&L Rendering 10 Mm Thick In Cement Mortar (1:3), As On Concrete Surfaces (Such As Top & Sides Of Chajjas, Beams, Balcony Ceiling Etc.) Finished Even And Smooth Without Using Extra Cement, Complete All As Specified. 8 M&L Preparing Of New Surface Of Wall And Applying Two Coats Of Exterior Emulsion Paint Over A Coat Primer On Walls Complete All As Specified And Directed By Engineer-In-Charge. Complete All As Specified And As Directed By Engineer-In-Charge . 9 M & L Preparation Of Newly Plastered Wall Surfaces Of Wall And Applying Two Coats Of Obd Over A Coat Of Chalk Whiting Putty Including Preparation Of Surfaces On Walls As Specified And Directed . 10 M&L For Preparation Of Newly Plastered Or Unplastered/Undecorated Surface Of Ceiling And Applying Two Coats Of Oil Bound Distemper Over One Coat Of Chalk Whiting Putty Complete All As Specified 11 M&L For Preparation Of Plastered Or Unplastered Old Decorated Surfaces By Complete Removal Of Existing Treatment By Mechanised Sander Of Berger Paints Or Equivalent Makes Viz Xpress Sanding Machine Having Suction Vaccum Bag Or By Manual Scrapping Tools Where Mechanical Removal Is Not Possible And Filling Of Holes And Cracks With With Suitable Material Like Cement Or Plaster Of Paris Etc And Thereafter Applying Two Coat Of Oil Bound Distemper On Walls. Note : (A) Stage For Preparation Of Surfaces Shall Be Got Approved From Engg-In-Charge Before Applying The Finishes.(B) Material Shall Be Procured From Manufacturer. 12 All As Per Item No.11 Here-In-Before But On Surfaces Of Ceiling. 13 M&L For Preparation(Complete Removal Of Existing Treatment) Of Old Decorated External Wall/Ceiling/Rppf Surface Of Existing Treatment By Scrapping With Trucare Wall Sander : L-01/H-01 (Having Mechanical Vaccum Mechanism) Having Rpm Not Less Than 1500, Sand Pad Of 80 Grit Having Dia Of 7\/9\ To Make The Surface Free From Dust, Loose Paint Etc Or Equivalent Makes Viz Xpress Sanding Machine Having Suction Vaccum Bag Or By Manual Scrapping Tools Where Mechanical Removal Is Not Possible And Applying Two Coats Of Wheather Proofing Exterior Acrylic Emulsion Paint Over Priming Coat Premium Quality On Wall/Roof Surface Upto 4Th Storey Buildings Complete All As Specified And Directed. Note : (A) Stage For Preparation Of Surfaces Shall Be Got Approved From Engg-In-Charge Before Applying The Finishes.(B) Material Shall Be Procured From Manufacturer And Work Shall Be Got Executed Through Authorised Applicator. 14 Pressed Steel Frames Made Out Mild Steel Sheet 1.25 Mm Thick, With Size Of Frame 125 Mm X 60 Mm For Doors With One Or More Rebates Including Necessary Fixing Lugs, Hinges, Lock Strike Plates Etc And Applying A Shop Coat Of Red Oxide Primer Including Providing Pcc 1:3 :6 Type C-0 Using 12.5 Mm Graded Crush Stone Aggregate For Filling Back Of Chowkhats Complete All As Specified And As Directed By The Engineer-In-Charge 15 Pressed Steel Frames Made Out Mild Steel Sheet 1.25 Mm Thick, With Size Of Frame 105 Mm X 60 Mm For Doors With One Or More Rebates Including Necessary Fixing Lugs, Hinges, Lock Strike Plates Etc And Applying A Shop Coat Of Red Oxide Primer Including Providing Pcc 1:3 :6 Type C-0 Using 12.5 Mm Graded Crush Stone Aggregate For Filling Back Of Chowkhats Complete All As Specified And As Directed By The Engineer-In-Charge 16 S & F 35Mm Thick 2Nd Class Hard Wood Glazed And Skeleton Shutters, Open Rebated And Prepared To Receive Glass, Gauze Etc. (Without Sash Bars), Edges Of Framing Plain, Chamfered Or Rounded, Fitted With Cut And Mitred Beads For Securing Glass, Etc.; Size Of Members Of Shutters As Specified In Ssr Part – I, Section – 8, Clause 8.20 (A) ; Supplied And Fitted To Chowkats All As Specified And Directed By Engineer - In - Charge 17 S & F Flush Shutter 35 Mm Thick Solid Core Construction With Block Board Core And Plywood Face Panels Commercial Type On Both Sides With Lipping / Frame To Match All As Specified And Directed By Engineer - In - Charge. 18 S & Faluminium Alloy, Anodised With Bright Bolt And Fixed, Length Of Bolt 200Mm Long All As Specified And Directed By Engineer - In – Charge . 19 S&F 300Mm Aluminium Alloy, Anodised,Sliding Door Bolt With Hasp, Staple (Bolt Type) And Fixing Clips Of Sheet, Cast Or Extruded Sections And Fixing Bolts And Sliding Bolts Of Extruded Sections Or Cast-Aluminium Alloy And Fixed 20 S & F Aluminium Handle Cast Type Anodised, 125 Mm Long All As Specified And Directed By Engineer - In - Charge . 21 S & F Stainless Steel Butt Hinges, Medium Weight 100Mm Size All As Specified And Directed By Engineer - In - Charge . 22 M&L For Providing Plain Cement Concrete (1:2:4) Type B0 (Using 12.5 Mm Graded Crushed Stone Aggregate) As In Coping Or Roof Kerbs On Roof Chamfered On Edge Including Trowelling Slightly Complete All As Specified. 23 Supply Only Intergral Water Proofing Compound Isi Marked Complete All As Specified. 24 Taking Down Chowkats Or Frames With Shutters (Without Taking Off Shutter From Frames) Not Exc. 1.5 Sqm Each, Including Cutting Holes For Removing The Hold Fast Etc (Distrubed Surface Of Wall Shall Be Make Good By The Contractor. The Rate Quoted Shall Be Deemed Included For The Same) Complete All As Specified. 25 Taking Down Chowkats Or Frames With Shutters (Without Taking Off Shutter From Frames) Exc. 1.5 Sqm But N Exc 4 Sqm Each, Including Cutting Holes For Removing The Hold Fast Etc (Distrubed Surface Of Wall Shall Be Make Good By The Contractor. The Rate Quoted Shall Be Deemed Included For The Same) Complete All As Specified. 26 Dismantling/Removing Old Damaged Worn Out App Of Any Thickness Incl Screed Bed Or Plastering Of Any Thickness And Removing The Rubish Materials Outside Mod Land At A Dumping Place Earmarked Marked By Any State Govt/Municipalities Etc Any Distance Complete All As Specified And As Directed.
Basic Detail
Tender No GE/GUR-/NIT-97/2026-27
Bidding Type Tender
Location
City Gurgaon
State Haryana
Key Dates
Publish Date 05 Oct 2026
Submission Date 26 Oct 2026
Open Date 28 Oct 2026
Finance
Tender Value 42.93 Lakhs
Tender Fee 500
EMD 88000
Exemption Not Available
Document List
b99fb542-86ba-40fe-966c-ed0b293fa752.html
BOQ_888491.xls
TenderDocumentsNIT97.pdf
Tendernotice_1.pdf

Unlock Full AI Tender Summary

Get instant access to the complete AI-generated analysis — scope, eligibility, timeline & more.

Instant Access Secure Free
Your details are secure and used only for document delivery.

Tender Timeline

Oct 05, 2026
11:30 IST

Tender Published

Tender notice published.

Completed
Oct 26, 2026
17:00 IST

Bid Submission Deadline

Online submission via eProcurement portal.

Upcoming · 19 days
Oct 28, 2026

Bid Opening Date

Technical bids will be opened and evaluated.

Upcoming · 21 days

Tender Documents

Download All (ZIP) ↓
html

b99fb542-86ba-40fe-966c-ed0b293fa752.html

xls

BOQ_888491.xls

pdf

TenderDocumentsNIT97.pdf

pdf

Tendernotice_1.pdf

Disclaimer

We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender

TenderDetail
Loading tenders