Tender For Renovation Of Kitchen At 2Nd Floor Including Provision Of One Toilet Block At Ground Floor In Mplsa, Door Sanchar Bhawan, Arera Hills, Bhopal (M.P.)
Tender Value
4.51 Lakhs
Estimated cost
Bid Submission
13 Oct 2026
7 days left
EMD
9050
Bank guarantee accepted
Document Fee
590
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Bhopal → Madhya Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Renovation Of Kitchen At 2Nd Floor Including Provision Of One Toilet Block At Ground Floor In Mplsa, Door Sanchar Bhawan, Arera Hills, Bhopal (M.P.)
BOQ
| Sl. No. | Item Description |
| 1 | Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge |
| 2 | 50 mm average thickness |
| 3 | Cleaning of reinforcement from rust from the reinforcing bars to give it a total rust free steel surface by using alkaline chemical rust remover of approved make with paint brush and removing loose particles after 24 hours of its application with wire brush and thoroughly washing with water and allowing it to dry, all complete as per direction of Engineer-In-Charge. |
| 4 | Bars above 12 mm diameter |
| 5 | Providing, mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and direction of Engineer-In-charge complete in all respect. |
| 6 | SBR Polymer (@10% of cement weight) modified cementitious bond coat @ 2.2 kg cement per sqm of surface area mixed with specified proportion of approved polymer |
| 7 | Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make. |
| 8 | Providing, mixing and applying SBR polymer (of approved make) modified Cement mortar in proportion of 1:4 (1 cement: 4 graded coarse sand with polymer minimum 2% by wt. of cement used) as per specifications and directions of Engineer-in-charge. |
| 9 | Note: Measurement and payment: The pre-measurement of thickness shall be done just after the surface preparation is completed and Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding / tapping with a blunt metal instrument and/or the 75mm size cube crushing strength at the end of 28 days to be not less than 30 N/Sqmm2). |
| 10 | 25 mm average thickness in 2 layers. |
| 11 | 50 mm average thickness in 3 layers. |
| 12 | Providing and laying in position excluding cement concrete of level: specified grade the cost of centering and shuttering - All work up to plinth |
| 13 | 1:2:4 (1 cement : 2 coarse sand (zone-Ill) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) |
| 14 | Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing : |
| 15 | 1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources: 10 graded stone aggregate 40 mm nominal size derived from natural sources). |
| 16 | Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : |
| 17 | Cement mortar 1:6(1 cement : 6 coarse sand) |
| 18 | Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. |
| 19 | Cement mortar 1:4(1 cement :4 coarse sand) |
| 20 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. |
| 21 | Granite stone slab colour black, Cherry/Ruby red |
| 22 | Area of slab upto 0.50 sqm |
| 23 | Area of slab over 0.50 sqm |
| 24 | Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. |
| 25 | Glazed Vitrified tiles Matt/Antiskid finish of size |
| 26 | Size of Tile 600 x 600 mm |
| 27 | Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer) with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make in all colours & shade in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1cement: 3 coarse sand), jointing with grey cement slurry @ 3.3kg/sqm including grouting the joint with white cement & matching pigments etc. complete. |
| 28 | Size of Tile 600x600 mm |
| 29 | Deduct for not using 20 mm thick cement mortar 1:4 (1 cement : 4coarse sand) bedding in laying of floor tiles and jointing with grey cement slurry @ 3.3kg/sqm |
| 30 | Fixing glazed/ Ceramic/ Vitrified floor tiles with cement based high polymer modified quick-set tile adhesive (Water based) conforming to IS: 15477, in average 3mm thickness. |
| 31 | Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete : |
| 32 | 250x16 mm |
| 33 | Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 34 | 150x10 mm |
| 35 | Providing and fixing aluminium pull bolt lock, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws bolts, nut and washers etc. complete. |
| 36 | Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : |
| 37 | 125 mm |
| 38 | 75 mm |
| 39 | Providing and fixing bright finished brass butt hinges with necessary screws etc. complete : |
| 40 | 75x40x2.5 mm (ordinary type) |
| 41 | Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete. |
| 42 | Twin rubber stopper |
| 43 | Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. |
| 44 | Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. ( All work Make Armstrong or equivalents) |
| 45 | 8 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of Gypsum plasterboard and laminated with white 0.07 mm thick fire retardant PVC film on the face side and 12 micron metalized polyester on the back side with all edges sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back side metalized polyester film so as to make the tile a completely sealed unit. (Tile work Make Gyproc-Saint Gobain or equivalents) |
| 46 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: |
| 47 | 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 48 | Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round UPVC Type-B Pipes including bed concrete as per standard design : |
| 49 | 110 mm diameter |
| 50 | Providing and fixing unplasticised rigid pvc SWR waste and vent pipes conforming to IS : 13592 Type B, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. |
| 51 | 110mm diameter. |
| 52 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :5382, leaving 10 mm gap for thermal expansion. |
| 53 | Single tee with door |
| 54 | 110x110x110 mm |
| 55 | Single tee without door |
| 56 | 110x110x110 mm |
| 57 | Bend 87.5° |
| 58 | 110 mm bend |
| 59 | Shoe (Plain) |
| 60 | 110 mm Shoe |
| 61 | Coupler |
| 62 | 110 mm |
| 63 | Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws etc complete as per direction of Engineer in charge. |
| 64 | 110 mm |
| 65 | 12 mm cement plaster of mix: |
| 66 | 1:6 (1 cement: 6 coarse sand) |
| 67 | 15 mm cement plaster on rough side of single or half brick wall of mix: |
| 68 | 1:6(1 cement: 6 coarse sand) |
| 69 | 6 mm cement plaster of mix: |
| 70 | 1:3 (1 cement: 3 fine sand) |
| 71 | Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 72 | Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre. of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. |
| 73 | One coat. |
| 74 | Two coats. |
| 75 | Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. |
| 76 | Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : |
| 77 | One or more coats on old work |
| 78 | Repairs to plaster of thickness 12 mm to 20 mm in patches of area 2.5 sq.meters and under, including cutting the patch in proper shape, raking out joints and preparing and plastering the surface of the walls complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. |
| 79 | With cement mortar 1:4 (1cement: 4 coarse sand) |
| 80 | Taking out existing wooden door shutter, repair by cutting, painting etc. and refixing of repaired door shutters to existing door frames, including replacement of hinges with screws, etc. as required, all complete as per the direction of the Engineer-in-charge. |
| 81 | Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. |
| 82 | Nominal concrete 1:4:8 or leaner mix (i/c equivalent design mix) |
| 83 | Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. |
| 84 | In cement mortar |
| 85 | Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : |
| 86 | Of area 3 sq. metres and below |
| 87 | Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. |
| 88 | For thickness of tiles 10 mm to 25 mm |
| 89 | Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal of rubbish to the dumping ground within 50 metres lead. |
| 90 | Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. |
| 91 | Providing and fixing wash basin with ,15 mm C.P. brass Long body pillar taps of Parryware/Jaguwar, 32 mm C.P. brass long waste coupling of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: |
| 92 | Table Top White Vitreous China Flat back wash basin size 500x 400 mm with single 15 mm C.P. long body brass pillar tap |
| 93 | Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with fittings, standard size C.P. brass waste coupling, C.P. spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556,with waste couplings in C.P. brass, including painting of fittings including bracket , faster etc as per direction of Engineer in charge |
| 94 | Single half stall urinal of 580x380x350 |
| 95 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. |
| 96 | Flexible pipe |
| 97 | 32 mm dia |
| 98 | Extra for providing opening of required size & shape for wash basin/kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete |
| 99 | Cutting holes up to 30x30 cm in walls including making good the same: |
| 100 | With common burnt clay F.P.S. (non modular) bricks. |
| 101 | Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 102 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall |
| 103 | 25 mm nominal dia Pipes |
| 104 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. |
| 105 | 20 mm nominal dia Pipes |
| 106 | Providing and fixing uplasticised PVC connection pipe with brass unions : |
| 107 | 45 cm length |
| 108 | 15 mm nominal bore |
| 109 | Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :(Parryware/Jaguar/Hindware or equivalent |
| 110 | 15 mm nominal bore |
| 111 | Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : |
| 112 | 25 to 40 mm nominal bore |
| 113 | Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 |
| 114 | 15 mm nominal bore |
| 115 | Providing and fixing CP Brasss grating of approved quality and colour. |
| 116 | Circular type |
| 117 | 125 mm nominal dia with 25 mm waste hole |
| 118 | Rectangular type with openable circular lid |
| 119 | 150 mm nominal size square 100 mm diameter of the inner hinged round grating |
| 120 | Providing and fixing PTMT Ball cock of approved quality, colour and make complete with Epoxy coated aluminium rod with L.P./ H.P.H.D. plastic ball. |
| 121 | 20 mm nominal bore, 120 mm long, weighing not less than 198 gms |
| 122 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : |
| 123 | For fixed portion |
| 124 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 125 | For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately). |
| 126 | Powder coated aluminium (minimum thickness of powder coating 50 micron) |
| 127 | Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): |
| 128 | With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) |
| 129 | Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry. |
| 130 | Providing and fixing unplasticised rigid pvc SWR fittings conforming to IS : 13592 Type B, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. |
| 131 | 110mm Y - Tee |
| 132 | Repairing of existing door / window shutter by chiseling, fixing of fittings like hinges, tower bolts, etc. if required for smooth operation of shutter all complete as per the direction of Engineer-In-Charge. |
| 133 | Cleaning of chocked sewer line including cleaning manhole by manual or mechanical means including disposal of debris in municipal dumping ground complete as per direction of Engineer-in-charge. |
| 134 | Providing and fixing Pre-laminated flat pressed 3 layer (medium density) particle board or graded wood particle board IS : 3087 marked, with one side decorative and other side balancing lamination Grade I, Type II exterior grade IS : 12823 marked, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately). |
| 135 | 18 mm thick |
| 136 | Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt / suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. |
| 137 | 1.0 mm thick. |
| 138 | Designing, fabricating,installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including: (a) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of approved shades made out of ACP panel contains, 0.21 to 0.25mm thick aluminium alloy coil along with a 2.5mm core. (c) The fastening brackets of Aluminium / MS all complete required to perform as per specification and drawing. The item includes cost of all material & labour component and working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain wall with aluminium composite panel cladding till the handing over of the building for occupation. The Contractor shall provide curtain wall with aluminium composite panel cladding, having all the performance characteristics all complete , as per the Architectural drawings, as per item description, as specified, as per the approvedshop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in sqm. up to two decimal places. |
| 139 | For fluted Shape(1'+3'+1') |
| 140 | For Plain area |
| 141 | Providing and fixing modular base cabinet fronts and internal partitions made of BWP grade plywood 19 mm thick, with front shutters finished in 1 mm laminate of approved shade, including internal shelves (where required), back panel, soft-close hinges, SS handles (upto 75 mm), and edge banding, fixed and aligned on marble slab supports provided below granite countertop, complete as per manufacturer’s specifications and direction of Engineer-in-Charge. (Measurement shall be taken as front elevated plan area of cabinet). Rate includes cost of all materials, labour, tools, fasteners, conveyance, and installation at site. (Bottom, side panels, and levelling legs not required due to marble support). |
| 142 | Providing and fixing wall-mounted modular kitchen cabinets made from BWP ply, 19 mm thick, with shelves and shutters in 1 mm laminate finish of approved shade, including soft-close hinges, aluminium handles, and adjustable hanging brackets. Carcass depth shall not be less than 350 mm, cabinet height around 600 mm. All exposed edges to be sealed with 0.8 mm PVC edge banding.Rate includes cost of all materials, labour, tools, fasteners, conveyance, cutting, wastage, and installation at site as per direction of Engineer in charge. |
| 143 | Providing and fixing cutlery drawer basket made of stainless steel (SS 304 grade) with solid bottom plate type construction (not wire mesh) of Make-Ebco / Hettich / Hafele or equivalent approved, fitted with soft-close telescopic slides, including PVC or rubber mat lining, screws, clips, and fixing hardware complete as per design.The basket shall have overall internal dimensions approximately Width 600 mm × Depth 450 mm × Height 100 mm, with smooth polished stainless-steel finish, rounded corners, and anti-corrosive coating.The rate includes cost of all materials, labour, cutting, edge finishing, fixing, alignment, and complete installation in position, (Each basket complete in position)all as directed by the Engineer-in-Charge. |
| 144 | Providing and fixing Quartz Single Bowl Kitchen Sink of size 610 × 460 × 230 mm (24\\" × 18\\" × 9\\"), made of Quartz composite material (approx. 80% natural quartz stone and 20% acrylic resin), with matt/satin finish, scratch, stain, and heat-resistant surface, including CI/SS brackets, stainless steel waste coupling (40 mm), CP bottle trap, making cut-outs in granite top, sealing joints, and making good the walls wherever required, complete in all respects as per direction of the Engineer-in-Charge. (Make: Carysil / Kaff / Franke / Nirali / Futura or equivalent) |
| 145 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. |
| 146 | Raj Nagar Plain white marble/ Udaipur green marble/ Zebra black marble |
| 147 | Area of slab upto 0.50 sqm |
| 148 | Area of slab over 0.50 sqm |
| 149 | Cleaning of existing manhole of inner size 90 cm x 80 cm, including removal of silt, sludge, debris, solid waste, and other foreign materials manually or mechanically, disposal of the same within a lead of 50 m, as directed by the Engineer-in-Charge. The work includes opening and refixing of the manhole cover, removal of water if any, and thorough cleaning of benching and channels to make the manhole fully functional, complete in all respects as per direction of Engineer-in-Charge |
| 150 | Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : |
| 151 | Inside size 90x80 cm and 45 cm deep RCC cover with frame (light duty) 455x610 mm internal dimensions,. |
| 152 | With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 |
| 153 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. |
| 154 | 15 mm nominal bore. |
| 155 | Credit for Old unserviceable CI Scrap obtained from dismantling work at site. |
| 156 | Credit for Old unserviceable aluminium section etc obtained from dismantling work at site. |
| 157 | Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 05, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysOct 15, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 9 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender