Tender For Construction Of Civil Work In Examination Hall Of Second Floor) Under Dmft (Pmkkky).
Tender Value
8.57 Lakhs
Estimated cost
Bid Submission
11 Oct 2026
5 days left
EMD
18000
Bank guarantee accepted
Document Fee
350
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Solan → Himachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Civil Work In Examination Hall Of Second Floor) Under Dmft (Pmkkky).
BOQ
| Sl. No. | Item Description |
| 1 | Providing form work with steel plates 3.15mm thick welded with angle ron in frame30x30x5mm. so as to give a fair finish including centring, shuutering, strutting and propping etc.with wooden battens and ballies, height of propping and centring below supporting floor to ceiling not exceeding 4 Mtrs, and removal of the same for insitu-reinforced concrete & plain concrete workinCentering and shuttering including strutting, proping etc, and removal for the same complete including carnage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 2 | Beams, cantilever, girders and lintels Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels not exceeding 1 metre in depth in all heights from floor |
| 3 | Flat surfaces such as soffits of suspended floors, roofs, landings and the like |
| 4 | Stair cases (except spiral stair cases) excluding but including preparing of the surface and finishing of the nosing upto all floor level complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 5 | Providing and laying in position specified grade of reiforceed cement concrete, excluding the cost of centring, shuttering, finishing and reinforcement-work upto floor two level complete and as per HP. PWD specifications of 1990 volume-1. including carriage of all, labour, equipments and materials to various location through all modes of transportation with in all leads, lifts, and other incidental charges |
| 6 | 1:1.50:3 (one cement isto one point five course sand isto three graded stone aggregate 20.00 mm (twenty milimeter) nominal size (Lintels, beams girders bressumers and cantilevers upto floor two level) complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 7 | Providing hoisting and fixing above plinth level upto floor five level Stair cases (except spiral stair cases) excluding landing but including preparing of the surface and finishing of nosing upto floor two level but excluding the cost of required centering shuttering with 1:1.5:3(one cement, one point five sand, three graded stone aggregate twenty milimetre nominal size (including carmage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer in-Charge |
| 8 | Steel reinforcement for reinforced cement concrete work including cutting/bending. binding and placing in position complete including cost of binding wire upto floor all level including camage of materials upto all leads and lifts as per the direction of the Engineer-in-Charge (a)Tor steel. |
| 9 | Brick work with common bunt clay building bricks F.P.S (Non modular) bricks of class designation 7.50 (seven point five) in super structure above plinth level upto all floor all levels in all shapes and sizes in cement mortar 1:6 (One cement Six sand) complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 10 | Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base lies of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strike plate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Chargee: |
| 11 | Providing and fixing Window and ventilators frames manufactured of channel section 75 x 21.60 40 (Seventy Five into Forty) millimeters for end frames and for center frame channel section 75 x 40 (Seventy Five into Forty) millimeters with Mild Steel flat (Seventy Five into Four) millimeters in combination welded together to make one frame with making square steel section with Mild Steel fiat of 20 x 4 (Twenty into Four) millimeters and 12 x 4 (Twelve into Four) millimeters, shutters of rolled steel section F-7B (Seven B) section including glass panes of 4 (Four) millimeters thick in glazed panel and wire gauge of designation 85 (Eighty Five) with 0 56 (Zero point Five Six) millimeters dia in wire gauge panel and fixed glazing fixed with anglecomplete including carriage of materials, labour tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 12 | Providing and fixing ISI marked flush door shutters conforming to IS 2202 (Part 1) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross 35 mm thick Including ISI marked Stainless Steel bult hinges with necessary screws complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 13 | Providing and fixing M.S grills of required pattern in frames of windows etc. with M.S flats, square or round bars etc. including priming coat with approved steel primer all complete Fixed to openings /wooden frames with rawl plugs screws etc complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 14 | 15mm cement plaster in single coat on fair side of brick/concrete/stone walls for interior plastering upto floor two level including arises, intermal rounded angles,chamfers and/or rounded angles nol exceeding 80 mm in girth and finished even and smooth (1) Cement Mortar 1:6 (1 cement 6 sand).complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 15 | 15mm Cement plaster in single coat on the rough side of brick/ concrete/stone walls for interior plastering upto floor two level including arises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth (iv) Cement Mortar 1:6(1Cement6 Sand) complete including carriage of matenais, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 16 | 6mm (six milimetre) cement plaster 1:3 (One cement isto three coarse sand) finished with a floating coat of neat cement and thick coat of lime wash on top complete, including carriage of all labour equipment & materials to various location through all leads, lifts & other incidental charges complete as per entire satisfaction of the Enginner-in-charge. |
| 17 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth.complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 18 | Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: 13.43.1 Water thinnable cement primer complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 19 | Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67ltr/10 sqm over and Including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 20 | Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone /plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metting thesurfacecomplete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 21 | Applying priming coal over new steel & other metal surfaces after & including preparing the surface by thoroughly cleaning oil grease dirt and other foreign matter and scoured with wire brushes fine steel wool scrapers and sand paper complete. With ready mixed priming paint brushing red lead, Red-oxide/zinc oxide chrom) complete including carnge of material upto all leads and lifts by all means and as per the direction of Engineer-In-charge |
| 22 | Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete 13.52.1 On steel works complete wherever required Including carrige of material upto all leads and lifts by all means and as per the direction of Engineer-In-charge |
| 23 | Providing and laying vitrified floor bles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement: 4 coarse sand), jointing with grey cement slurry @33 kg/sqm including grouting the joints with while cement and matching pigments etc, complele Size of Tile 600x600 mm complete including carige of material upto all leads and lifts by all means and as per the direction of Engineer-In-charge |
| 24 | Precast terrazzo tiles hydraulic compressed 20 mm thick (with marble chips of specified 3.93 sizes) in skirting and risers of steps not exceeding 30 cm in height on 10 mm thick cement plaster 1.3 (1 cement 3 sand) jointed with neat cement slurry mixed with pigment to match the shade of biles (wherever required)including rubbing and polishing complete with tiles offollowing shades - MEDIUM Shade complete. including carige of material upto all leads and lifts by all means and as per the direction of Engineer-in-charge |
| 25 | Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete including camage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 26 | Providing and fixing M.S. tower bolts (barrel type) with necessary screws etc. complete. including carrige of material upto all leads and lifts by all means and as per the direction of Engineer-In-charge 250x10 mm complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 27 | Providing and fixing M.S. tower bolts (barrel type) with necessary screws etc.complete..including carrige of material upto all leads and lifts by all means and as per the direction of Engineer-In-charge 150x10 mm complete including camage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 28 | Providing and fixing M.S. handles with necessary screws complete 125 mm complete Including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 29 | Providing and fixing bright finished brass hard drawn hooks and eyes 300 mm complete including carriage of materials, labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge |
| 30 | Providing and fixing M.S. sliding door bolts bright finished or/and black enamelled with nuts and screws etc complete 300x16mm complete including carriage of materials. labour, tool and plant through all modes of transportion within all leads and lifts and as per direction of Engineer-in-Charge Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 04, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 11, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysOct 12, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender