Tender For special Repair To Bldg No T-450 And T-277 And Allied Works Jn Line And Certain Revenue Work Under Cijw School Vairengte
Tender Value
40.50 Lakhs
Estimated cost
Bid Submission
24 Oct 2026
21 days left
EMD
81000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Kolasib → Mizoram
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for special Repair To Bldg No T-450 And T-277 And Allied Works Jn Line And Certain Revenue Work Under Cijw School Vairengte
BOQ
| Sl. No. | Item Description |
| 1 | B & R Division Items |
| 2 | Demolition of un-reinforced cement concrete in ground floor and paving not exceeding 15 cm thick (below or above ground level) complete all as specified and directed. |
| 3 | Demolition of brick work or stone/ boulder masonry, built in cement mortar including all quoins, pillars etc. complete all as specified and as directed. |
| 4 | Dismantling mild steel work or wrought iron of any description and in any position complete all as specified and as directed. |
| 5 | Dismantling plain or corrugated steel sheeting, any gauge or any thickness as in roof covering, wall cladding, etc.including all necessary staging / scaffolding, etc. as required complete all as specified and as directed. |
| 6 | Dismantling wall and ceiling boards (fibre, pulb, insulation etc) or insulation boards slabs/blankets any thickness including cover fillets all as specified and as directed. |
| 7 | Taking down cement plaster on brick or stone walls etc, including raking out joints, hacking for key scrubing down with water etc complete all as specified and as directed. |
| 8 | Taking down chowkhats or frame with shutters (without taking off shutters from frame) each not exceeding 1.50 Sqm each complete all as specified. |
| 9 | Taking down Chowkhats or frames with shutters exceeding 1.5 Sqm but not exceeding 4 Sqm each (without taking off shutters from the frame) complete all as specified. |
| 10 | Excavating in trenches, n exc 1.50 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out soft/ loose type of soil complete all as specified and directed. |
| 11 | Returning, filling in trenches including spreading, leveling watering and ramming in layers not exceeding 25cm all as specified. |
| 12 | Removing of surplus soil not exceeding 50 m and deposited where directed at a level not exceeding 1.50m above the starting point all as specified. |
| 13 | M&L for Hardcore broken stone of gauge exc 40mm and n exc 63mm deposited spread and levelled in layers n exc 15cm thick watered and rammed to a true surface complete all as specified and directed. |
| 14 | M&L for PCC (1:4:8), Type D2 using 40 mm graded stone aggregate as in foundations, sub-base,filling and mass concrete complete all as specified. |
| 15 | M & L for 75mm thick plain cement concrete 1:3:6 type C1 using 20mm graded stone aggregate as in plinth protection finished even and fair without using extra cement complete all as specified. |
| 16 | M & L for 40 mm thick Plain Cement concrete type B2 1:2:4 (20mm graded crushed stone aggregates) as in floor surface finished even and fair all as specified and directed. |
| 17 | M & L for Cement Concrete nominal mix 1:2:4 type B1 using 20 mm graded aggregate aS in surface channels, drains ( forming fair finished channel shall be measured and paid for seperately ) complete all as specified and directed. |
| 18 | M & L for Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms, moulds mitered/stopped ends, etc all as specified. |
| 19 | Forming Construction joint 30 mm deep x 10 mm wide filled with sealing compound grade 'A' complete all as specified and directed by Engr-in-Charge. |
| 20 | Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter rough finished flat surfaces of concrete complete all as specified and as directed. |
| 21 | Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete all as specified and directed. |
| 22 | Use and waste Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide all as specified and directed. |
| 23 | M & L for providing Reinforced Cement Concrete nominal mix 1:1.5:3 type A1 using 20 mm graded aggregate a in foundation including rafts, footings, foundation beams, plinth beams, bases for columns etc complete all as specified and directed. |
| 24 | M & L for providing Reinforced Cement Concrete nominal mix 1:1.5:3 type A1 using 20 mm graded aggregate as in columns, pillars, piers, posts and struts complete all as specified and directed. |
| 25 | M & L for providing Reinforced Cement Concrete nominal mix 1:1.5:3 type A1 using 20 mm graded aggregate as in beams, cantilever, lintels over 1.5 m complete all as specified and directed. |
| 26 | M & L for 10mm dia and over TMT bars, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 27 | M & L for 6mm to 8mm dia and over TMT bars, cut to length bend to shape as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed. |
| 28 | M & L for Mild Steel TMT Bar 6mm dia and over up to 10 mm dia as in stirrups, spacers and binders as required including cranking, hooking etc and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete all as specified and directed |
| 29 | M & L for brickwork with subclass 'B' bricks, straight or curved on plan exc 6 m mean raduis, built in CM (1:6) complete all as specified and directed. |
| 30 | M & L for brick work in cement mortar (1:4) straight or curved on plan to any radius with locally available Subclass ‘B’ half brick thick wall complete all as specified . |
| 31 | M & L for 15 mm thick rendering in cement mortar 1:6 on fair faces of brick wall or concrete surfaces, finished the surfaces even and fair without using extra cement complete all as specified. |
| 32 | M & L rendering 15 mm thick cement mortar (1:4) on fair faces of brick wall or concrete surfaces, in two layer each of 10+5 mm thick & water proofing compound mixed with second layer @ 3% finished fair and even complete all as specified. (Note :WPC measured separately). |
| 33 | M&L for 15 mm thick screed bed of cement mortar 1:6 for laying floor finishes complete all as specified. |
| 34 | Supply only integral water proofing compound WPC complete all as specified. |
| 35 | M & L light vitrified ceramic tiles coloured 7 to 8mm thick (square/ rectangular) area of each tile not exceeding 0.36 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over including 15 mm thick screed bed or bedding layers in cement mortar 1:6 for tile over brushing with neat cement slurry as specified |
| 36 | M & L light vitrified ceramic tiles coloured ceramic tiles 7 to 8 mm thick ( square/rectangular) area of each tiles exc 0.18 sqm but not exc 0.38 sqm set in vertical surfaces as skirting/dado and jointed in neat cement slurry and pointed in white or colour cement to match over & including 10mm thick screed bed or backing coat in cement mortar 1:4 laying of skirting/dado on walls all as specified and directed. |
| 37 | M & L Non Skid ceramic tiles coloured 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.06 but not exceeding 0.11 sqm, as in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15 mm thick screed bed or bedding layers in cement mortar 1:6 complete all as specified and directed |
| 38 | M & L Glazed ceramic coloured tiles in vertical surface size 450mm x 300mm x & ( 6mm to 7mm )mm thick set on Skirting/Dado and jointed in neat cement slurry and pointed in white or colour cement to match over & including 10mm thick screed bed or backing coat in cement mortar 1:4 laying of skirting/dado on walls all as specified and directed. |
| 39 | M&L chequered coloured cement concrete tiles 25mm thick, with grey cement and pigment set, jointed and pointed in neat cement slurry, laid over 20mm thick screed bed in CM (1:6) complete all as specified and as directed. |
| 40 | S & F pre-painted galvalume aluminium zinc coating GI based corrugated/trepozoidal steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 41 | S & F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified. |
| 42 | S & F Framed work such as grills, gratings, etc.. with ends of bars or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed. |
| 43 | S & F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers,hold fasts, bands, straps, wall ties, plain angle cleats, eaves board frame and similar articles conforming to Fe-290 Gde-E-165 complete all as specified and directed. |
| 44 | S & F structural steel work in tubular/hollow sections trusses , Purlin , posts, rafter etc including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St.-240 complete all as as specified and directed. |
| 45 | S & F Solid PVC door frame of size 50mm X 47mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube complete all as specified in clause 8B.3.1 and shown on page 150 of MES Schedule Part-II (2010). |
| 46 | S & F factory made single extruded PVC double door frame of size 50mm X 95mm made of 5 mm single side prelaminated colour PVC sheet reinforced with mild steel square tube ,fixed in opening as per specification & drawing complete all as specified . |
| 47 | S & F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, fixed in the frame at site as per clause 8 B.2.1 of MES schedule Part-II (2004) complete all as specified. Make: Rajshri or equivalent as approved. |
| 48 | S & F Factory made wire gauzed PVC moulded door shutter 30 mm thick (style) wire gauzed i.e. panel will be of wire gauze in lieu of wood grain printed PVC sheet panel. The wire gauze shall be wrapped on an additional square 8mm M.S. Solid tube and this tube shall be welded to M.S. tubes. The wire gauge shall be stretched to tighten firmly consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded wood grain printed PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of wood grain printed PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing. |
| 49 | S & F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick prelaminated Moulded PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing complete all as specified. |
| 50 | M & L Plain Cement concrete (1:3:6), type C-1 using 20mm graded stone aggregate as in filling of hallow steel chowkhats, bed block, fixing of holdfast and similar likes including necessary formwork complete all as specified. |
| 51 | S & F 3 ways sliding anodized aluminium glazed window shutter with frame with the following specification all as specified & directed.(a) Window frame 3 track of size 95mm × 25mm × 1.5mm thick.(b) Stiles and rails of size 35mm × 25mm × 1.5mm.(c) 35mm × 35mm × 1.5mm T section mullion.(d) PVC gasket with 4mm thick tinted glass, incl. aluminium handles with necessary locking arrangement for 02 Nos glazed shutter.(e) Stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40 mm, fixed with stainless steel wire staples, incl. aluminium handles with necessary locking arrangement for 01 No gauzed shutter.Note: Measurement to be taken as overall width and height of window. No shutter or frame to be measured separately. All necessary accessories including tinted glass and stainless steel wire cloth required for assembling and fixing window at proper place complete are deemed to be inclusive. |
| 52 | S & F 2 way sliding anodized aluminium glazed ventilator shutter with frame consists of following specification all as specified & directed.(a) Ventilator frame 2 track of size 60mm X 25mm X 1.5mm thick.(b) Stiles and rails of size 35mm X 25mm X 1.5mm.(c) 35mm X 35mm X 1.5mm T section mullion.(d) PVC gasket with 4mm thick tinted glass, incl. aluminium handles with necessary locking arrangement.Note: Measurement to be taken as overall width and height of ventilator. No shutter or frame to be measured separately. All necessary accessories including tinted glass required for assembling and fixing window at proper place complete are deemed to be inclusive. |
| 53 | S&F 100mm long stainless steel Butt hinges, with stainless steel screws complete all as specified and directed. |
| 54 | S & F 150 mm long aluminium handles cast type anodised complete all as specified & directed . |
| 55 | S & F 150 mm long extruded brass handles fabricated type polished complete all as specified & directed . |
| 56 | S & F 200 mm long brass barrel tower bolts of with cast or sheet barrel and rolled or cast bolts and fixed complete all as specified and directed. |
| 57 | S & F 200 mm long aluminum anodised barrel tower bolts of extruded section complete all as specified and directed. |
| 58 | S & F 250mm brass sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolts with rolled or drawn brass bolts and fixed complete all as specified. |
| 59 | S&F as in repairs 25 mm dia stainless steel curtain rods with brackets incl fixing stops, rollers bracket etc with harrison rails all as specified and directed . |
| 60 | S & F, vitreous china wash basin, white flat back size 550 x 400 mm, excluding taps, waste chain, plug and porcelain stopper but including waste coupling, brackets, cutting for and pinning in ends of bracket or erecting stand complete all as specified. |
| 61 | S & F in repair vitreous china Squatting pan, 'Orissa' pattern, Size 580 X 440mm ,with integral foot rests (excluding flushing ciestern and flush pipe) incl necessary cement concrete bedding all as specified & as directed . |
| 62 | S & F soap dish chromium plated standerd quality fixed on wall with brass screw complete all as specified. |
| 63 | S & F PVC waste coupling of PTMT ( half or full threaded) minimum weight 45gms for 32mm dia dischartge pipe complete in all respect as specified |
| 64 | S & F PVC connections 15mm dia size with PTMT nuts of length 450mm complete in all respect as specified |
| 65 | S & F 15mm bore pillar tap cast copper alloy with capstan head, chromium plated concealed screwed down high pressure with or without hot or cold with long shunk screwed shanks and fly nuts screwed for iron pipes and connecting to water pipe line complete all specified and directed. |
| 66 | S & F 15mm bore stop valves/angle valve of cast copper alloy, concealed, cup screwed down, high pressure with crutch or butter fly handle, chromium plated, fancy type with long shank fixed complete all as specified. |
| 67 | S & F Towel rail tubular, 20mm dia brass chromium plated, 600mm long, D type with fancy type brass chromium plated brackets on both sides and fixed with steel screws and wooden/rawl plugs complete all as specified. |
| 68 | S & F 600mm X 450mm bevelled edge mirror of selected quality glass, mounted on 9mm thick commercial plywood and PVC moulding frame fancy type complete all as specified and directed. |
| 69 | M&L for PCC (1:3:6),Type C2 using 40 mm graded stone aggregate as in bed to drain for 300 mm bore including packing under and hunching against side of pipe after they are laid and tested complete all as specified. |
| 70 | S&F LLDPE Septic tank at site designed to carry sewage and sullage water, excavation in any type of soil, 150mm thick PCC 1:4:8 type D-2 use for foundation, vent shaft, connection etc for 30 user all as specified and directed |
| 71 | S & F 15mm bore galvanised iron water tubes medium grade with all fittings and fixed to wall, ceiling or laid in floor and trench complete all as specified. |
| 72 | S & F 20mm bore galvanised iron water tubes medium grade with all fittings and fixed to wall, ceiling or laid in floor and trench complete all as specified. |
| 73 | S & F 150mm bore PVC pipes single socketed with rubber ring joint, in any length, laid in trenches, or in floor, for eves gutter complete all as specified. |
| 74 | S & F 110mm bore PVC (SWR) pipes single socketed with rubber ring joint, in any length, laid in trenches or in floors / fixed to walls complete all as specified. |
| 75 | S & F 75mm bore PVC (SWR) pipes single socketed with rubber joint, in any length fixed to walls / floors or in trenches complete all as specified. |
| 76 | S & F 150mm bore PVC (SWR) bend suitable for pipe complete all as specified. |
| 77 | S & F 110mm bore PVC (SWR) bend suitable for pipe complete all as specified. |
| 78 | S & F 75mm bore PVC (SWR) bends suitable for pipe complete all as specified. |
| 79 | M & L for Cutting into existing manholes for connecting new drains of 150mm internal dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1½ round or 3/4 Section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required. |
| 80 | S & F 150mm bore PVC (SWR) junction, single T equal or unequal with or without door access complete all as specified. |
| 81 | M & L PVC(SWR) floor trap, 75mm dia outlet, plain with grating including jointing with solvent cement complete all as specified. |
| 82 | S&F Solid PVC Wall Lining consisting of 5mm thick wood grain printed PVC sheet inclusive of solvent cement and fixing at site on PVC frame complete all as specified and directed. |
| 83 | S & F 5mm thick PVC sheet fillet of width 35mm for wall paneling, inclusive of fixing on to wall to make PVC frame complete all as specified and directed. |
| 84 | S & F in repairs for 4mm dia GI wire fixed to both ends of wall by means of necessary fastening bolts or T-shape nut and bolt for hold the wire all as specified and as directed. |
| 85 | S & F false ceiling with semi perforated 12 mm thick micro tegular edged or 10 mm thick square edge at all heights with GRG (Glass Fiber Reinforced Gypsum) false ceiling tiles of size 595 × 595 mm of approved texture design and pattern having moisture content less than 2%, humidity resistance of 99%, NCR 0.50 to 0.75 as per IS 8225 : 1987, non-combustible as per BS 475 (Part-IV) 1970 and light code description Unit Rate No. 429, Sub Head 26.0 – New Technologies and Material, reflectance of 85% minimum, laid in true horizontal level, suspended on interlocking metal T-grid of hot dipped galvanized iron section of 0.33 mm thick (galvanized @ 120 gms/sqm including both sides) comprising of:Main T runner of size 15 X 32 mm, length 3000 mm.Cross T of size 15 X 32 mm, length 1200 mm.Secondary intermediate cross T of size 15 X 32 mm, length 600 mm.To form grid module of size 600 X 600 mm, suspended from ceiling using galvanized metal sheet item (galvanized @ 80 gms/sqm), i.e. 50 mm long, 8 mm outer diameter M-6 fasteners, 6 mm dia fully threaded hanger rod up to 1000 mm length, and L-shape level adjusters of size 85 X 25 mm, galvanized iron perimeter wall angle of size 24 X 24 X 0.40 mm, length 3000 mm, to be fixed on perimeter of wall/partition with the help of plastic rawl plugs at 450 mm centre to centre and 40 mm long drywall screws.The work shall be carried out as per specification, drawing and as per direction of Engr-in-Charge |
| 86 | M & L for preparation of new or previously untreated wall surfaces and applying three coats of white wash complete all as specified and directed. |
| 87 | M & L for preparation of new or previously untreated wall surfaces and applying two coats of cement base paint over one coat of primer on walls complete all as specified and directed |
| 88 | M & L for preparation of new plastered surface and applying wall care putty in two coats of 1.5mm thickness over plastered surface to prepare the surface even and smooth complete all as specified. |
| 89 | M & L preparation of new plastered surface of walls and applying two coat of acrylic distemper over a coat of alkali resistant primer including preparation of newly plastered surfaces, complete all as specified. |
| 90 | M&L for preparation of new plastered untreated surface and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm using roller complete all as specified and directed. |
| 91 | M & L for preparation of new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer complete all as specified and as directed. |
| 92 | M & L for preparation of old steel surfaces of any description not otherwise described over 10cm width or girth applying one coats of synthetic enamel paint complete all as specified and as directed. |
| 93 | E & M Division items |
| 94 | Taking down carefully copper/aluminium point wiring (light, fan, buzzer, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc including removing from site for taking credit and making good to disturbed surface of walls, floors etc as per existing specification complete all as specified and as directed. |
| 95 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty,concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One light point controlled by one switch. |
| 96 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One fan point/exhaust fan point controlled by one, one way switch 5 Amp. |
| 97 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, concealed PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One 3 pin 5 Amp socket outlet point controlled by one switch on the same board. |
| 98 | M & L for point wiring with FRLSH stranded copper conductor 1.5 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, PVC Conduit including all accessories etc ISI marked, with GI sunken box suitable for fixing switches, sockets and regulators including PVC insulated stranded copper conductor 1.5 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for One 3 pin 5 Amp socket outlet point controlled by one switch on independent board. |
| 99 | M&L for point wiring with FRLSH stranded copper conductor 4.0 sqmm (nominal area), two single core, PVC insulated cable 1100 volts grade, ISI-694 marked in and including heavy duty, concealed PVC Conduit concealed type of suitable size including all accessories etc ISI marked, with GI sheet pressed terminal box (recessed) with 3mm thick laminated hylem sheet top cover for fixing switches, sockets and regulators including PVC insulated FRLSH stranded copper conductor 4.0 sqmm (nominal area) single core cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for one power point on independent board of AC/equipments etc controlled by one SP/SPN MCB. Note: The point wiring will be done from DBs to the switch sockets of any size with three wires running independently for each point and with no tappings. |
| 100 | S&F switch piano flush type button single pole one way 5 Amps all as specified and directed. |
| 101 | S&F socket outlet combination 2 in 1, 3 pin 6 and 16 Amp flush type universal all as specified and directed. |
| 102 | S&F socket outlet combination 2 in 1, 3 pin 6 Amp flush type universal all as specified and directed. |
| 103 | S&F Socket outlet 2 in 1, 3 pin, 5 and 15amp flush type all as specified and directed. |
| 104 | S&F ceiling rose surface bakelite with three terminals all as specified and directed |
| 105 | S&F lamp holder insulated body withback plate for batten fitting including necessary connection complete all as specified. |
| 106 | S & F surface mounting batten tube light fitting 20 Watt 4 feet long, integrated polycarbonate LED channel with white acrylic cover complete suitable for and including Lamp 1X20 Watt fixed properly on wall surface and connecting complete from ceiling rose to fitting by three core copper conductor cable of overall sheathed size 2.5 Sqmm which shall be passed through PVC flexible conduit complete all as specified and directed.. |
| 107 | S&F building security light LED fitting 25/35 watt 230V AC outdoor type with high pressure die cast aluminum housing and heat resistant, epoxy powder coated dark graphite grey colour finish and prismatic polycarbonate cover with individual LED lences suitable for including lamp LED 25/35 watt, fixed/connect properly at directed location on building with IP 65/66 protection complete including taking down existing old one complete all as specified and as directed. |
| 108 | S & F bracket for street light fittings of any size made out of Gl pipe medium grade 25/32 mm dia 1.25 mtr length bend to required size and shape including provision of clamps and fittings in position and two coat of aluminum paint over a coat of red oxide primer complete including taking down existing old one complete all as specified and as directed. |
| 109 | S&F for Plastic body Exhaust Fan 250 mm sweep, single phase 230 volts AC, 900 RPM four blade with louver shutters complete fixed properly on wall surface with the provisioning of suitable sizes of rag bolts, nuts, washer and to connect by using cable PVC insulated copper stranded conductor of size 1.5 Sqmm 3 core and overall PVC sheathed which shall be passed through PVC flexible conduit of length not exceeding 0.50 mtr complete including taking down existing old one complete all as specified and as directed. |
| 110 | S&F Ceiling fan 1200mm sweep single phase 230 volts AC, min air delivery 210 CFM with service valve 6.00 BEE 5 star rating with brushless direct current motor (BLDC) with blade down roads electronic regulator and complete accessories complete fixed properly on wall surface with the provisioning of suitable sizes of rag bolts, nuts, washer and to connect by using cable PVC insulated copper stranded conductor of size 2.5 Sqmm 3 core and overall PVC sheathed which shall be passed through PVC flexible conduit of length not exceeding 0.50 mtr all as reqd complete including taking down existing old one and deposit to AGE Vairengte E/M Store (not in Schedule of Credit) complete all as specified and as directed. |
| 111 | S&F Factory made distribution board sheet metal enclosure powder coated single phase neutral (SPN) 8 way double door with Aluminum bus bar 100 Amp including grouting on the wall by means of screws and rawal plugs and making good disturbed surfaces complete all as specified and directed. |
| 112 | S&F MCB SPN of capacity 6-32 Amps, 240 V, 10 KA 'C' curve complete including taking down existing old one complete all as specified and as directed. |
| 113 | S&F MCB SP of capacity 5-32 Amps, 240 V, 10 KA 'C' curve complete including taking down existing old one complete all as specified and as directed. |
| 114 | Taking out existing old earthing and M & L for new earthing with galvanised steel earth plate electrode 600mmX600mmX6mm thick burried directly in ground (earth pit not less than 2.25 mtr below ground level) with top edge of the plate not less than 1.5 mtr below ground level connected to 4mm dia GI wire protected by 20 mm bore light grade galvanised iron pipe and other end connected to test point as directed including funnel with wire mesh and watering pipe 20 mm bore medium grade galvanised iron pipe with charcoal and common salt in alternaterlayers of 15 cm thickness all around the GI plate electrode with concrete pit in PCC 1:3:6 type C-1 with cast iron frame including cast iron cover 10mm thick hinged to CI frame and 6mm MS rod for handle, necessary excavation and earth wok in hard/dense soil and disposal of spoil to a distance n exc 50 m and necessary testing complete all as shown in electrical plate No 3 of SSR part-I complete all as specified and directed. |
| 115 | Supply, fixing, commissioning & testing of XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, Electric power cable (heavy duty) with aluminium conductors, cross sectional area 16 sqmm 4.0 core 1100 volts grade laid in trenches/fixed to wall/under road/pipe etc with copper cable glands & copper thimbles complete all as specified and directed. |
| 116 | S & F for steel water tubing 32mm dia, medium grade galvanised with new fittings laid in trenches or on wall with clamp digging complete all as specified and directed. |
| 117 | S & F for steel water tubing 25mm dia, medium grade galvanised with new fitting laid in trenches or on wall with clamp digging complete all as specified and directed. |
| 118 | M&L for Fan hook fabricated with MS Flat 25X6mm 350mm long 02 nos bend to shape drilled with holes and MS nut, boltsandwasher of required as per side with one coatof primer and two coatof paints as per site complete including taking down existing old one complete all as specified and as directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 03, 2026
11:30 IST
Tender Published
Tender notice published.
TodayOct 24, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 21 daysOct 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 24 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender