Tender For Special Repair To Bldg No Owt-28,Owt-29, Owt-30 And Owt-54 (Chdh) At Borarupak Mil Stn Under Ge 872 Ews
Tender Value
42.19 Lakhs
Estimated cost
Bid Submission
26 Oct 2026
11 days left
EMD
84400
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Upper Subansiri → Arunachal Pradesh
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Special Repair To Bldg No Owt-28,Owt-29, Owt-30 And Owt-54 (Chdh) At Borarupak Mil Stn Under Ge 872 Ews
BOQ
| Sl. No. | Item Description |
| 1 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposal of debris and rubbish complete all as specified and directed. |
| 2 | Demolition of un-reinforced cement concrete in ground floors and pavings n.exc 15cm thickness, (Below or above Ground level) and disposal of debris and rubbish to a distance complete all as directed. |
| 3 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as directed and directed |
| 4 | Demolition of brick work or stone masonary built in cement mortor including all quoins & jambs etc. complete all as specified and directed |
| 5 | Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in mortar complete all as specified and directed. |
| 6 | Taking down chowkats or frame, n.exc 1.5 Sqm each with shutters (without taking off shutter from the frame) complete all as specified and directed. |
| 7 | Taking down chowkats or frames, exc 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed. |
| 8 | Taking down Shutters, exc 1.0 but n.exc. 2.00 Sqm with fittings complete all as specified and directed. |
| 9 | Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water and removing rubbish complete all as specified and directed |
| 10 | Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges and keeping serviceable sheets in safe custody for reuse in the work complete as directed. |
| 11 | Dismantling of wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed. |
| 12 | Dismantling Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets/ snap grid frame etc complete all as specified and directed. |
| 13 | Taking up or down 15 mm bore, Steel tubing and connections and keeping serviceable pipes in safe custody for reuse in the work after and including cleaning as directed. |
| 14 | Taking up or down 25 mm bore, Steel tubing and connections and keeping serviceable pipes in safe custody for reuse in the work after and including cleaning as directed. |
| 15 | Taking up or down 20 mm bore, Steel tubing and connections and keeping serviceable pipes in safe custody for reuse in the work after and including cleaning as directed. |
| 16 | Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, trenches for shafts, wells, cesspits, manholes, pier holes, cable etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed. |
| 17 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed. |
| 18 | Removing excavated material not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed. |
| 19 | M & L Reinforced Cement Concrete 1:2:4, Type B-1(nominal design mix (20mm graded crushed stone aggregate) as in Slab supported on Walls, complete all as specified and as directed. |
| 20 | M & L for Pre-cast cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate), block masonry with solid blocks of size 300x200x200mm or 300x200x100mm, having compressive strength of not less than 100 Kg/Sq Cm (As per IS-2185) exc. 10 cm in width and setting in mortar 1:6 complete all as specified and directed. |
| 21 | M & L for Providing, cement concrete 1:2:4 type B-1(using 20 mm graded) as in copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, all as specified & directed |
| 22 | S&F Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and as directed. |
| 23 | S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc., complete all as specified and as directed. |
| 24 | S & F Anodised aluminium door shutters,aluminium section weighing 0.55 kg/m including necessary joining cleats,glazing clips, ruber neoprene packing,handles 2 Nos in each door, hinges,anodised aluminum snap beading screws etc. complete all as specified & directed. |
| 25 | S&F Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed .Note:- Fixing of wire mesh and glass shall be measure and paid separately under relevant items. |
| 26 | M&L Steel Ventilator with frame ,top hung shutter including hinges, steel peg stay, complete with glazing bars ,dovetailed or welded complete all as specified and as directed. |
| 27 | M&L Steel Ventilator with frame ,top hung shutter including hinges, steel peg stay, complete without glazing bars ,dovetailed or welded complete all as specified and as directed. |
| 28 | S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides fitted to cowkhats complete all as specified and directed. |
| 29 | S&F for 2nd class hardwood 30 mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats as specified in SSR Part-I 2009.complete all as specified and directed |
| 30 | M & L 35 mm thick , 2nd class hardwood plain , framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats , complete all as specified & directed. |
| 31 | M & L 18/19 mm Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work all as specified & directed. |
| 32 | S & F Stainless steel wire cloth. 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 33 | S & F in repair Stainless steel wire cloth. 0.56mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staples complete all as specified and directed. |
| 34 | S & F 5.5 mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed. |
| 35 | S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed. |
| 36 | S & F 100 mm long, stainless steel butt hinges fixed with stainless steel hinge pin etc complete all as specified and directed. |
| 37 | S & F 150 mm long, Aluminium anodised, barrel tower bolts of extruded section complete all as specified and directed. |
| 38 | S & F 150 mm size, extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed. |
| 39 | S & F 300 mm Aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clipes of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy, length of bolt complete all as specified and directed. |
| 40 | S & F 300 mm size MS door spring including roller plate by means of welding or screwing down complete all as specified and directed. |
| 41 | S&F Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring (overall length of cover plate 150mm) complete all as specified and as directed. |
| 42 | S & F Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer's instruction complete all as specified and directed. |
| 43 | S & F Pre-Painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/vally gutter, fixed with self tapping screws as per manufacturer's instruction complete all as specified and directed. |
| 44 | M&L Mild Steel Work in Tubular Trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conform-ing to IS:1161-1979 grade St.-240, complete all as specified and as directed. |
| 45 | S&F Rolled mild steel as in Compound girders and stanchions, lattice girders, aerial masts, staging for water tanks and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc. and fixing complete Fe 290 Gde-E-165 quality-A complete all as specified and directed. |
| 46 | M & L Rolled sections as in iron chowkats ,framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc.(Grade Fe 290 E165) all as specified & directed. |
| 47 | S & F Chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 all as specified & directed. |
| 48 | S & F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe-410-W (Gde-E-250) quality-B complete all as specified and directed. |
| 49 | S & F mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed. |
| 50 | S & F high strength TMT steel bars 10 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed. |
| 51 | S & F aluminium Anodised snap grid frame work of size 605mm x 605mm frame work for ceiling with aluminium T section of size 38mm x 25mm x 1.5mm thick for main runners, 25x25x1.5mm thick for cross runner and angle size 25x25x1.5mm thick alongwith wall suspended and including Hangers 4/2 mm dia. G.I. (upto 1200mm length) adjusting level fixed to ceiling members in proper position, fixed with aluminium staple on snap grid as per manufacturer's instructions including 6 mm thick non asbestor E-board, HSPC, designer fixed to frame complete all as specified and directed. |
| 52 | M & L for 25 mm thick, plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in flooring, etc and finished the surface even and smooth without using extra cement complete all as specified and directed. |
| 53 | M & L 75 mm thick cement concrete 1:3:6 type C-1( using 40 mm graded stone aggregate)as in sub base for receving the floors finishes,complete all as specified and directed. |
| 54 | M & L 40 mm thick cement concrete 1:2:4 type B-2( using 20 mm graded stone aggregate0as in sub base for receving the floors finishes ,complete all as specified and directed. |
| 55 | M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed. |
| 56 | M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, in floors etc, and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortor 1:6 complete all as specified and directed. |
| 57 | M&L Glazed Ceramic Coloured Tile 450 x 350 x 7.0mm thick on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc., Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over and including 10mm thick backing layer in cement mortar (1:4) complete all as specified and as directed. |
| 58 | M&L Granite (of any type) Work (Table rubbed and polished) 18 to 20 mm thick, in Steps, Cooking Platforms and like, Set in Screed bed of 20mm thick in Cement Mortar 1:4 including Pointing in White Cement 1:2 using Marble Dust with admixture of Pigment to match with Shade of Granite including Cutting and Polishing including half round edges, complete all as specified and as directed. |
| 59 | S&F Machine cut kota stone slab flooring 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and granite finish polishing complete over 20mm thick 1:6 cement mortar screed bed complete all as specified and as directed. |
| 60 | M & L for Chequered cement concrete tiles of size 20cm x 20cm x 25mm thick, as in floors etc, including 15 mm thick screed bed in cement mortar 1:6 and set & jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and directed. |
| 61 | M & L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished the surfaces even and fair complete all as specified and directed. |
| 62 | M&L 15 mm thick rendering in cement mortar (1:4) on fair faces of brick or concrete external surfaces in two layers (each 10mm + 5 mm thick) finished even and smooth without using extra cement using water proofing compound on top layer @2% by weight of cement or as per manufactures instruction complete all as specified and directed.Note : WPC shall be measured and paid seperately |
| 63 | M&L Rendering 15mm thick in Cement Mortar 1:4 on other than fair faces of Brick Walls or on Concrete Surfaces, finishing plastered surfaces Even and Smooth without using Extra Cement complete all as specified and as directed. |
| 64 | S & F water proofing compound (as approved), conforming to IS : 2645-2003, complete all as specified & directed. |
| 65 | M & L for Preparation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of alkali resistant primer complete all as specified and directed. |
| 66 | M & L for preparing newly plastered surfaces of walls, etc and applying three coats of white wash complete all as specified and directed. |
| 67 | M&L for Preparation of new plastered surfaces and applying two coats of oil emulsion distemper (any colour/tint) over a coat of primer over 3 mm thick wall care putty (Birla/Asian) on wall surfaces including rubbing with emmery paper to make wall surface smooth and even complete all as specified and directed. |
| 68 | M & L for preparation of old painted surfaces of wall panel/plaster surface over 10 cm width or girth , not otherwise described and applying two coats of synthetic enamel paint over a coat of primer , complete all as specified & directed. |
| 69 | M & L for preparation of plastered or unplastered old decorated surfaces of walls by brooming down or steel wire brushing scrapping down smoke soot , moulds , moss and efflorescent , salts and trading oil greasy spots and applying one coat of cement base paint on walls , complete all as specified & directed. |
| 70 | M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zine chrome primer complete all as specified and directed. |
| 71 | M & L for Preparation of old painted steel surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint complete all as specified and directed. |
| 72 | S & F in repair 15 mm bore, pillar taps, fancy type, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed. |
| 73 | S & F in repair 15 mm bore, Stop/angle valves, cast copper alloy, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed. |
| 74 | S & F in repair 15 mm bore, bib taps, fancy type, cast copper alloy, chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule fixed in repair complete all as specified and directed. |
| 75 | S & F in repair 20 mm bore, gun metal Gate valves, with iron wheel head, Class-I, Pressure Tested of 1.5 Mpa, screwed both ends for iron pipe complete all as specified and directed. |
| 76 | S&F in repair Rotational Moulded Polyethylene (HDPE) Water Storage Tank 1000 Litre Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I including provision of 25mm x 100mm GI nippples with check nuts for inlet, outlet wash and overflow pipe including 20 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe and including Lowering of old/unserviceable Water Storage Tank of any description, complete all as specified and as directed. |
| 77 | S&F in repair PVC connection 15mm size with PTMT nut of length 450mm complete all as specified and directed. |
| 78 | S&F in repair Brass chromium plated tubular towel rail, 20mm dia, D type, 60,cm long between flanges as in repair complete all as specified and directed. |
| 79 | S&F 20mm dia brass chromium plated tubular curtain rod with fixing brackets, stops, rollers etc complete all as specified and as directed. |
| 80 | S & F in repair 600mmX450mm bevelled edge mirror of selected quality glass, mounted on 6mm thick AC building board or commercial plywood and fixed to wooden plug with chromiun plated brass screws and cup washers complete all as specified and directed. |
| 81 | S & F High density polyethylene pipes (HDPE)50 mm of pressure rating 6 kgf/cm2 fixed complete to walls, ceiling or in floors etc. including fittings required complete all as specified & directed. |
| 82 | S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm all as specified & directed. |
| 83 | S&F CPVC pipes 25 mm outer diameter of SDR 11 & plain CPVC SDR 11 fittings fixed on Walls, Ceiling or laid in Floors or any other Situation, etc incl all fittings complete as all specified and as directed. |
| 84 | S&F CPVC pipes 32 mm outer diameter of SDR 11 & plain CPVC SDR 11 fittings fixed on Walls, Ceiling or laid in Floors or any other Situation, etc incl all fittings complete as all specified and as directed. |
| 85 | S&F CPVC pipes 20 mm outer diameter of SDR 11 & plain CPVC SDR 11 fittings fixed on Walls, Ceiling or laid in Floors or any other Situation, etc incl all fittings complete as all specified and as directed. |
| 86 | S&F in repair Vitreous China Wash Hand Basin Pedestal type 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia Brass Chromium Plated Waste Fitting, a pair of Cast Iron Brackets duly painted including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 complete all including taking down old/unsv wash basin ,fittings etc.as specified and as directed. |
| 87 | Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc. complete all as specified and directed. |
| 88 | Taking down unserviceable main switches, DBs, bus bars chambers, VTPN etc any capacity including all fittings and fixtures such as MCBs, isolator, etc and removing from site complete all as specified and directed. |
| 89 | Taking down copper/aluminium submain wiring complete ,including fixture and fittings such as PVC casing caping/conduit , junction box and including GI wire accessories etc. and making good disturbed surfaces of walls, floors, etc complete all as specified and directed. |
| 90 | M & L for Point wiring for one light/exhaust fan/fan point/call bell controlled by one way switch with two runs of single core 1.5 Sq.mm. (Nominal area) PVC insulated unsheathed multistranded copper conductor cable FRLSH (ISI marked) drawn through and including non metallic PVC casing capping (ISI marked) (aprox size 20/25/40mm width) surface type with all fittings/fixtures such as Tee, Bend, elbow, socketr, shaddle etc including 1.5mm thick MS sunken/terminal box including 3mm thick backelite sheet cover for fixing flush type switches, sockets, regulators etc. including provision of multistranded 1.5 Sq.mm copper conductor cable FRLSH [ISI marked] as earth wire connected to common earth dolly and earth in distribution board complete all as specified and as directed.(Note.: (i) The rate quoted is deemed to include making good the disturbed sufaces and to match the adjoining surface.) |
| 91 | All as per item No. 90.00 above but for One 3/5 pin socket outlet 6 amps point on same board complete ditto , all as specified and directed. |
| 92 | All as per item No. 90.00 above but for One 3/5 pin socket outlet 6 amps on independent board complete ditto ,all as specified and directed. |
| 93 | All as per item No. 90.00 here in before but for one 15 Amps power point on the independent board with two runs of PVC insulated and unsheathed copper conductor cable of size 2.5 sqmm multistranded FR (ISI marked) and 2.5 sqmm PVC insulated unsheathed solid copper conductor cable FR (ISI marked) as earth lead complete ditto , all as specified and directed. |
| 94 | M&L Sub main wiring with2 runs of single core 10.0 sqmm PVC insulated unsheathed 1100 volts grade ,copper multi stranded conductor drawn in PVC conduit ISI marked including with its fittings and fixtures such as tees , bends , elbows , junction boxes etc. including multistrand copper conductor 10.0 sqmm (nominal cross sectional area) single core , PVC insulated , unsheatered FRLSH cable 1100 volts grade , ISI marked with vailed CML number as continuity earth wire drawn through and connected to main switch/DB and socket for AC complete all as specified and directed. |
| 95 | S & F Modular switch one way 6 Amp 240 volts, 1 module ,240 volt AC and connecting up ,complete all as specified and as directed. |
| 96 | S & F Modular Socket outlet 2 in 1, 3 pin, 5/6 Amps, flush type complete all as specified and as directed. |
| 97 | S & F Modular Switch socket combination 2 in 1, 3 pin, 6 Amp, flush type, universal complete all as specified and as directed. |
| 98 | S & F Modular Switch socket combination 2 in1, 3 pin, 6 and 16Amp, flush type, universal complete all as specified and as directed. |
| 99 | S & F ceiling rose, 65 X 50mm two to three terminals, PVC/polycarbonate, insolated body complete all as specified and directed. |
| 100 | S & F Modular fan step regulator,120W-2 module, 240 volt and connecting complete all as specified up ,complete all as specified & directed. |
| 101 | S & F LED Bulb 15 watt complete all as specified & directed. |
| 102 | S & F Angle Holder , PVC /polycarbonate type with backplate including LED Bulb , 15 watts , B-22 Lumen ≥ 900, Luminous afficancy ≥ Lum/watt, CCT: WW/NW/CW, CRI > 80 Ra , IP20 rated ,overmounted plastic housing, polycarbonate diffuser , 4 KV surge protection with over Voltage protection withstand upto 440 V (for 10 minute) with open and short circut protections as per IS :16102 complete all as specified & directed. |
| 103 | S & F LED tube light fittings, retro bar professional WH 5700K to 6000K, 20 Watt and 2000 Lumens of cool white with all accessories, internally prewired and connecting up with twin core twisted copper conductor cable of suitable size including tube lamp complete all as specified and directed. |
| 104 | S & F 36 Watt (100lm/w), 2ftx2ft, LED recessed full lit luminaire with glare free uniform illumination with loger life and less maintenance with all accessories, internally prewired and connecting up including tube lamp complete all as specified and directed. |
| 105 | S & F LED Bulk Head, 10 Watt, IP 65 rated, compact design, PC Co extruded with high energy saving with all accessories and connecting up including lamp complete all as specified and directed. |
| 106 | S & F LED building security light fitting of capacity 18 watt, 240 V AC outdoor type with for fixing to Bldg , complete all as specified & directed. |
| 107 | M & L for Street light bracket made out of 60 cm long 32/40 mm dia light grade GI pipe welded to 200 mm long 100 mm GI pipe with provision of nut and bolts for fixing on top of the pole duly painted with two coats of silver paint over a coat of red oxide primer, complete all as specified & directed. |
| 108 | S & F sheet metal enclosure for DB's when MCBs to be used 12-way, SPN , 240V, Double door with IP 43 protection epoxy based powder coated suitable for mounting MCB DP/SPN as incomer and MCB SP as out -goings with 200 amps rated Bus-bar , neutral Bar, earth bar, connecting cable links and connecting up , including taking down unserviceable sheet metal enclosure of any description ,complete all as specified and as directed. |
| 109 | S & F sheet metal enclosure for DB's when MCBs to be used 8-way, SPN , 240V, Double door with IP 43 protection epoxy based powder coated suitable for mounting MCB DP/SPN as incomer and MCB SP as out -goings with 200 amps rated Bus-bar , neutral Bar, earth bar, connecting cable links and connecting up , including taking down unserviceable sheet metal enclosure of any description ,complete all as specified and as directed. |
| 110 | S & F sheet metal Enclosure socket plug Top and MCB Double pole and neutral enclosure with a two pin and earth plug and socket of 20 Amp complete with one double pole MCB complete all as specified & directed. |
| 111 | S & F MCB SPN 6-32A Amps, 240 Volts, 10KA, C Curve complete all as specified and as directed |
| 112 | S & F Isolator TPN, 415 Volts, complete all as specified and as directed Please Enable Macros to View BoQ information |
| 113 | S & F Isolator TPN, 415 Volts, complete all as specified and as directed Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 03, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 26, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysOct 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 13 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender