Tender For Maintenance Of Hospital Quarters (Type-I, Ii & Iii) At Debdaru Phc, South Tripura District During The Year 2026-27./Sh:Dismantling Works, Wood Works, Aluminium Works, Finishing Works,Sanitary Fittings, Roof Grading Etc.
Tender Value
15.29 Lakhs
Estimated cost
Bid Submission
07 Oct 2026
5 days left
EMD
30598
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
tripura → Tripura
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Maintenance Of Hospital Quarters (Type-I, Ii & Iii) At Debdaru Phc, South Tripura District During The Year 2026-27./Sh:Dismantling Works, Wood Works, Aluminium Works, Finishing Works,Sanitary Fittings, Roof Grading Etc.
BOQ
| Sl. No. | Item Description |
| 1 | SUB HEAD : DISMANTLING AND DEMOLISHING WORK:Dismantling old plaster or pointing,raking out joints,cleaning and preparing the surface for replastering or re-pointing including disposal of rubbish to the dumping ground with all leads and lifts etc. complete as per direction of the Engineer- in-charge. |
| 2 | Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres leadOf area 3 sqm and below. |
| 3 | Dismantling old glass panes from wooden / steel structures including stacking of serviceable materials and disposal of rubbish and unserviceable materials to the dumping ground with all leads and lifts etc.complete as per direction of the Engineer- incharge. |
| 4 | Dismantling of flushing cistern of all types (C.I./PVC/Vitrious China) including stacking of useful materials near the site and disposal of unserviceable materials within 50 metres lead. |
| 5 | SUB HEAD : WOOD WORKProviding wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position : Local Teak Wood |
| 6 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veeners on both faces of shutters.35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws. |
| 7 | Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinforced with 19×19mm MS square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame . The door frame to be fixed to the wall usuing MS screws of 65/100 mm size complete as per manufacturers' specification and direction of Engineer-In-Charge. |
| 8 | Providing and fixing to existing door frames. 30mm thick factory made solid panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for stiles, top & bottom rails. M.S .frame shall have a coat of steel primers of approved make and manufacture M.S. frame covered with 5mm thick heat moulded PVC ‘C channel of size 30mm thickness, 110mm width out of which 90mm shall be flat and 20mm shall be tapered in 45 degree angle on either side forming stiles; and 5mm thick, 110mm wide PVC sheet out of which 90mm shall be flat and 20mm shall be tapered on the inner side to form top and bottom rail and 130mm wide PVC sheet out of which 90mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top bottom and lock rails shall be provided either side of the panel. 10mm (5mm x 2) thick, 20mm wide cross PVC sheet shall be provided as gap insert for top rail & bottom rail. Panelling of 5mm thick PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with 7mm (5mm +2mm) thick x 15mm wide PVC sheet bending on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the ‘C Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in charge, manufacture’s specification & drawing. |
| 9 | Providing 40 × 5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30 × 10 × 15 cm 1:3:6 mix (1 cement : 3 fine sand : 6 graded stone aggregate 20mm nominal size) |
| 10 | Providing and fixing bright finished brass towerbolts (barrel type)with necessary screws etc. complete :250 x 10 mmProviding and fixing bright finished brass towerbolts (barrel type)with necessary screws etc. complete :250 x 10 mm |
| 11 | Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: |
| 12 | Providing and fixing chromium plated brass handles with necessary screws etc. complete: 125 mm |
| 13 | SUB-HEAD - ROOFING WORKSupply & installation of pre-painted Galvalume sheets for roofing/cladding (size, shape and pitch ofcorrugation as approved by Engineer-in-charge) in 550mpa steel grade, made out of Cold Rolled Steelcoated with Zinc-Aluminium alloy coating of 43.5% Zn 55% Al and 1.5% Silicon confirming to ASTMA792/A792M and AS1397, Alloy coating AZ150/AZ70,colour coated with high quality Polyester coating, topcoated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micronon both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches whiletransportation and should be supplied in single length upto 12 metre or as desired by Engineer-incharge.The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDMwashers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfacesexcluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever requiredand as per direction of Engineer-in-charge.0.50mm thickness |
| 14 | SUB-HEAD - FINISHING WORKFinishing walls with acrylic smooth exterior paint of required shade of approved brand and manufacture[Payment shall be made after submission of Test Certificate issued by the Manufacturer] New work ( two or more coats applied @ 1.67 litre/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm |
| 15 | 15 mm cement plaster on the rough side of single or half brick wall of mix: : Cement mortar 1 : 4 ( 1 cement : 4 fine sand ) |
| 16 | Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surfaceeven and smooth complete. |
| 17 | 12 mm cement plaster of mix Cement mortar 1 : 4 ( 1 cement : 4 fine sand ) |
| 18 | Applying priming coat [Payment shall be made after submission of Test Certificate issued by theManufacturer] :- With ready mixed Pink or Grey primer of approved brand and manufacture on wood work ( hard & soft wood ). |
| 19 | Painting with synthetic enamel paint of approved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: Two or more coats on new work |
| 20 | Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 grams/ litre, ofapproved brand and manufacture to give an even shade [Payment shall be made after submission of Test Certificate issued by the Manufacturer] : [Payment shall be made after submission of Test Certificate issued by the Manufacturer] :New work ( two or more coats) over and including water thinnable priming coat with cement primer. New work ( two or more coats) over and including waterthinnable priming coat with cement primer |
| 21 | SUB HEAD : ALUMINIUM WORK & STRUCTURAL GLAZING:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineerincharge. (Glazing and paneling and dash fasteners to be paid for separately) :-(a) For fixed portion of approved quality:-Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 22 | For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required ( Fittings shall be paid for separately ):-Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodiccoating of grade AC 15). |
| 23 | Providing and fixing glazing of aproved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber/ neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) :-With float glass panes of 5.5 mm thickness ( weight not less than 13.50 kg / sqm ) |
| 24 | SUB HEAD : SANITARY INSTALLATIONProviding and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid |
| 25 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps,32 mm C.P. brass waste ofstandard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require :White Vitreous China Wash basin size 630x450 mm with apair of 15 mm C.P. brass pillar taps. |
| 26 | Providing and fixing Stainless Steel AISI 304 (18/8) kitchen sink as per IS 13983 with C.I. brackets andstainless steel plug 40 mm including painting of fittings and brackets, cutting and making good the walls wherever required:- Kitchen sink with drain board, 510x1040 mm bowl depth 250mm |
| 27 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.Semi rigid pipe 32 mm dia |
| 28 | Providing and fixing mirror of superior glass (of approved quality) and of required shape and size withplastic moulded frame of approved make and shade with 6 mm thick hard board backingRectangular shape 453x357mm |
| 29 | Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from wall ofstandard shape with bracket of the same materials with snap fittings of approved quality and colours weighingnot less than 105 gms. |
| 30 | Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screwswith concealed fitting arrangement of approved quality and colour.600mm long towel rail with total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms. |
| 31 | SUB-HEAD-WATER SUPPLYProviding and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall(i)15 mm dia. nominal bore |
| 32 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. (ii)20 mm dia. nominal bore |
| 33 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement ,trenching ,refilling & testing of joints complete as per direction of Engineer in Ch. (i)25 mm dia. nominal bore |
| 34 | Providing and fixing PTMT bib cock of approved quality and colour.15mm nominal bore, 86 mm long, weighing not less than 88 gms. |
| 35 | Providing and fixing PTMT stop cock of approved quality and colour. 15 mm nominal bore, 86mm long, weighing not less than 88 grams. |
| 36 | Providing and fixing PTMT pillar cock of approved quality and colour 15mm nominal bore, 107mm long, weighing not less than 110 grams. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysOct 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender