Tender For 1)Development Of Natural Football Ground At Bholagiri Near Tuda Housing Complex. 2)Construction Of Multipurpose Sports Hall (40Mx60m) At Bholagiri Ground Near Tuda Housing Complex,Agartala,West Tripura. 3)Construction Of International Size
Tender Value
Ref. Documents
Estimated cost
Bid Submission
28 Oct 2026
24 days left
EMD
45.57 Lakhs
Bank guarantee accepted
Document Fee
10000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
tripura → Tripura
EMD Exemption
Not Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for 1)Development Of Natural Football Ground At Bholagiri Near Tuda Housing Complex. 2)Construction Of Multipurpose Sports Hall (40Mx60m) At Bholagiri Ground Near Tuda Housing Complex,Agartala,West Tripura. 3)Construction Of International Size Swimming Pool At Bholagiri Ground, Near Tuda Housing Complex,Agartala, West Tripura.
BOQ
| Sl. No. | Item Description |
| 1 | Development of Natural Football Ground at Bholagiri near TUDA Housing complex. |
| 2 | Clearing grass and removal of the rubbish upto a distanceof 50 m outside the periphery of the area cleared. |
| 3 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm indepth, 1.5m in width as well as 10 sqm on plan) includingdisposal of excavated earth, lead upto 50m and lift upto1.5m, disposed earth to be levelled and neatly dressed.-All kinds of soil |
| 4 | Earth work in excavation by mechanical means (Hydraulicexcavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) includingdressing of sides and ramming of bottoms, lift upto 1.5 m,including getting out the excavated soil and disposal ofsurplus excavated soil as directed, within a lead of 50 m.-All kinds of soil |
| 5 | Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres as per direction of the of the Engineer-in-Charge. |
| 6 | Filling available excavated earth (excluding rock) intrenches, plinth, sides of foundations etc. in layers notexceeding 20cm in depth, consolidating each depositedlayer by ramming and watering, lead up to 50 m and liftupto 1.5 m.-All kinds of soil |
| 7 | Excavating, supplying and filling of local earth (includingroyalty) by mechanical transport upto a lead of 5 km also including ramming and watering of the earth in layers notexceeding 20 cm in trenches, plinth, sides of foundation etc.complete. |
| 8 | Supplying and filling in plinth, under floor, foundations etc.with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading torequired slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitablemethod complete. |
| 9 | Spreading of Sludge / Farm Yard Manure / good Earth Spreading of sludge/ farm yard manure/ good earth inrequired thickness (cost of sludge, farm yard manure or/and good earth to be paid for separately) MoRT&Htechnical specifications Clauses 307. |
| 10 | 401 Granular Sub-base with Well Graded Material (Table 400.1)(A) By Mix in Place Method,Construction of granular sub-base by providing well graded material spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per MoRT&H Technical Specification Clause 401.(i) For Grading I Material |
| 11 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering --All work upto plinth level:- |
| 12 | 1:2:4 ( 1 Cement: 2 fine sand : 4 graded stone aggregate20 mm nominal size) |
| 13 | Providing and laying in position specified grade ofreinforced cement concrete excluding the cost ofcentring, shuttering, finishing and reinforcement--All work upto plinth level: 1:1½:3 ( 1 Cement: 1½ fine sand : 3 graded stone aggregate 20 mm nominal size) |
| 14 | Reinforcement for R.C.C. work including straightening,cutting, bending, placing in position and binding allcomplete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 15 | Centering shuttering including struttings, propping etc.and removal of form work for: |
| 16 | Foundations, footings, bases for columns etc. for mass concrete with timber plank |
| 17 | Columns, Pillars, Piers, Abutments, Posts and Struts with shuttering ply |
| 18 | First class brick work in foundation and plinth including cost of all materials as required complete:- In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 19 | Steel work welded in built up section/framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using Ingrating, frames, guardbar, railing, brackets, gates and similar works, all complete. |
| 20 | 6 mm cement plaster of mix : Cement mortar 1:4 (1 cement : 4 fine sand) |
| 21 | Neat cement punning. |
| 22 | Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture |
| 23 | Finishing walls with water proofing cement paint of required shade of approved brand and manufacture [Payment shall be made after submission of Test New work ( two or more coats applied @ 3.84 kg/10 sqm) |
| 24 | 60 mm thick factory made c.c. interlocking paver block of M-35 Grade Providing and laying factory made coloured chamfered edge Cement Concrete paver blocks of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. complete as per specifications & approval/ direction of Engineer-in-Charge . (a) 60 mm thick c.c. paver block of M-35 grade with approved colour, design and pattern. |
| 25 | Plantation for football ground using bermuda grass (by seed/vegetative plantation),including ground preparation, sowing,watering,application of manure, fertilizer,pesticide,and maintenance, complete as per direction of Engineer-in-charge.(protection till establishment with own cost and risk) |
| 26 | Supplying and installation of football goalpost Aluminium-fixed/ socket-type(removable FIFA standard specification-made of alluminium 120mm dia as per fifa specification,ground sleeves made from 123 ID ms pipe,goal-post are duly tested and passed as per the requirements BS:EN-748-2013+A1-2018,size of goal post length 24' x Height 8' |
| 27 | Providing and laying 200 mm dia PVC perforated pipe (6 kg/cm² pressure) in trench including excavation, sand bedding,(granular backfill payment will be paid seperately) jointing with approved PVC solvent cement, maintaining proper alignment and slope @ 1:300, refilling, disposal of surplus earth, testing and all incidental works complete as directed by Engineer-in-Charge. |
| 28 | Supplying & Fixing Chain link fabric fencing mesh of size 50x50 mm made of G.I. wire of dia 4 mm GI/MS wire) with MS angle vertical posts at 2.50 m C/C,including necessary horizontal and diagonal bracing with MS angle,fixing with nuts, bolts, binding wire,welding etc. complete.( height of fencing 1.60m to 2.40m) |
| 29 | Supply & installation of Dugout(international standard)length-7.31m x width-1.22m x height-2.13m(24'x4'x7'),base structure made of 100mmx50mm MS rectangular pipe,Top structure made of 50x50 MS square pipe,Six non-marking wheels movable and lockable,Polycarbonate sheet 2.5mm made by 100% virgin lexan material,PC sheet UV stabalized complete including nuts,bolts etc as direction of Engineer-in-charge. |
| 30 | Supplying assembling boring / drilling bore well of 150 - 200 mm dis & lowering 75mm dia PVC (oriplast brand) casting pipe including 75 mm dian strainer pipe (at least 5 X 10 = 50ft ) including 32mm PVC (oriplast) column pipe including necessary clamp, well cap head base socket point safety wire bend etc. complete including gravels size range 5-10 mm (atleast 0.50mm). (payment should be made for successfull boring only for the length of casing pipe & Strainer pipe) |
| 31 | Supply and installing 1HP 15 Stage 3\\" 1Phase Water Filled Borewell Submersible Pump (KS3D-1015, Kirloskar) including Control panel and necessary 2.5sqmm pvc insulated three core flat copper wire including fitting fixing and lowering etc complete as specified and as directed by the Engineer-in-Charge. |
| 32 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 15 mm nominal outer dia .Pipes. |
| 33 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 20 mm nominal outer dia .Pipes. |
| 34 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 25 mm nominal outer dia .Pipes. |
| 35 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 40 mm nominal outer dia .Pipes. |
| 36 | Construction of Multipurpose Sports hall(40x60m) at Bholagiri Ground, near TUDA housing complex, Agartala,west Tripura |
| 37 | Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared |
| 38 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. for all kind of Soil |
| 39 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kind of soil |
| 40 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. All kind of soil |
| 41 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. |
| 42 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete |
| 43 | Treatment of soil under plinth filling using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with sand filling: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 44 | Providing and laying in position cement concrete of specified grade excluding the cost of centring and shuttering 1:4:8 ( 1 Cement: 4 fine sand : 8 graded well burnt brick aggregate 40 mm nominal size) - All works upto Plinth Level. |
| 45 | Providing and laying in position ready mixed plain cement concrete, with cement content as per approved design mix and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for plain cement concrete work, including pumping of R.M.C. from transit mixer to site of laying and curing, excluding the cost of centering, shuttering and finishing, including cost of curing, admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. Note : 1) Excess/less cement used than specified in this item is payable/ recoverable separately. M-15 grade plain cement concrete (cement content considered @ 240 kg/cum) - All works upto Plinth Level. |
| 46 | Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of gradeM-25 of specified diameter and length below the pilecap, to carry a safe working load not less thanspecified, excluding the cost of steel reinforcement but including thecost of boring with bentonite solution and temporary casing ofappropriatelengthforsetting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct Mud Circulation(DMC) or Bailerand Chisel Technique by Tripod and Mechanical Winch Machine all complete, including removal of excavated earth with all itsliftsandleads. (Lengthofpileforpaymentshall bemeasured upto bottomof pile cap). Note: Truck Mountedrotary/TMR/Tubewell Boring Machines hall not be used. |
| 47 | Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer incharge: Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic Method of Testing Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in Charge.Initial test (Test Load 2.5 times the safe Capacity). |
| 48 | Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per specification & the direction of Engineer incharge: Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic Method of Testing Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-inCharge. Routine test (Test Load 1.5 times the safe Capacity) |
| 49 | Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per the direction of Engineer-in-Charge. (Note :- Cement content considered in this item is @ 418 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level Reinforced cement concrete grade M-25 using 418 kg of cement per cum |
| 50 | Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per the direction of Engineer-in-Charge. (Note :- Cement content considered in this item is @ 418 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto Floor five level Reinforced cement concrete grade M-25 using 418 kg of cement per cum |
| 51 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 52 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 53 | Centering shuttering including struttings, propping etc. and removal of form work for: Foundations, footings, bases for columns etc. for mass concrete with timber plank |
| 54 | Centering shuttering including struttings, propping etc. and removal of form work for: Suspended floors, roofs, landings, balconies and access platform with 12 mm thick shuttering ply. For all floors |
| 55 | Centering shuttering including struttings, propping etc. and removal of form work for: Lintels, beams, plinth beams, girders, bressumers and cantilevers with shuttering ply. For all floors |
| 56 | Centering shuttering including struttings, propping etc. and removal of form work for: Columns, Pillars, Piers, Abutments, Posts and Struts with shuttering ply. For all floors |
| 57 | Centering shuttering including struttings, propping etc. and removal of form work for:Stairs (excluding landings) except spiral-staircases with wooden plank. For all floors |
| 58 | Providing precast cement concrete Jali 1:2:4 (1 cement: 2 coarse sand : 4 graded stone aggregate 6mm nominal size) reinforced with 1.6 mm dia mild steel wire including centring and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3(1cement : 3 fine sand) etc. complete, excluding the plastering of jambs, sills and soffits. For all floors |
| 59 | Extra for additional height in centring, shuttering where ever required with adequate bracing, propping etc. including cost of de-shuttering and decentring at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof: Suspended floors, roofs, landing, beams and balconies (Plan area to be measured). |
| 60 | Providing and fixing Galvanized chicken mesh (24 guage, 12 mm size) properly stretched and nailed ensuring equal thickness of plaster at junction of masonry work and concrete members. |
| 61 | First class brick work in foundation and plinth including cost of all materials as required complete. In cement mortar 1:5 ( 1 cement : 5 fine sand ). |
| 62 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:- In cement mortar 1:5 ( 1 cement : 5 fine sand ). |
| 63 | Half brick masonry work with first class bricks in superstructure upto floor five level including cost of all materials as required complete:- In cement mortar 1:4 ( 1 cement : 4 fine sand ). |
| 64 | Providing and laying Polished Granite stone flooring and sill jambs in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 fine sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18 mm thick stone slab |
| 65 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framedand fixed in position : Local Teak Wood |
| 66 | Providingandfixingpanelled/orpanelledandglazed shutters fordoors,windowsandclerestorywindows including ISI marked bright finished / black enamelled M.S butt hinges with necessary screws xcludingpanellingandorglazing,which will be paid separatelybutincludingthewoodenbeadingof 20 ×12mmfor fixingpanellingandor glazing as per direction of Engineer-In-Charge. 35 mm thick shutters |
| 67 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90mm x 45mm having single rebate of 32mm x 15mm to receive shutter of 30mm thickness .The laminate shall be molded with fire resistant grade unsaturated polyester resin and chopped mat .Doorframe laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fibreglass from all sides. MS stay shall be provided at the bottom to steady the frame |
| 68 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 69 | Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of shutters (over all area of door shutter to be measured) |
| 70 | Providing and fixing ISI marked oxidised M.S. door latches conforming to IS:5930 with screws etc. complete :300 x 20 x 6 mm |
| 71 | Providing and fixing to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5mm thick FRP laminate for panels confirming to TADS 6: 1993 and / or IS: 14856 - 2000 including fixing to frames |
| 72 | Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 125 mm |
| 73 | Providing structural steel work in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required. For all floors |
| 74 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes Kg. |
| 75 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 76 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm at 100 mm centre to centre and braced with flat iron diagonals 20x5mm sizewith top and bottom rail of T-iron 40x40x6mm with 40mm dia. steel pulleys & with riveted bolts, nuts, locking arrangement, stoppers, handles, hold fast /anchor bolt including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approvedsteel primer etc. complete as required. |
| 77 | Providing and fixing Kota stone in floors over 20 mm thick bed of cement mortar 1 : 4 ( 1 cement : 4 fine sand ) jointed with ordinary cement slurry including pointing with ordinary cement mixed with pigment of matching shade, including rubbing and polishing etc. all complete as per direction of Engineer-in-charge. Kota stone slab 25mm thick |
| 78 | Providing and fixing 1st class quality ceramic glazed wall tiles conforming to IS : 15622- 2017 (thickness to be specified by the manufacturer) of approved make in all colours, shades of any size as approved by Engineer-in charge in skirting, risers of steps and dados, laid over 12 mm thick bed of cement mortar 1 : 3 (1 cement : 3 fine sand) jointed with ordinary cement slurry including pointing with white cement mixed with pigment of matching shade etc. all complete as per direction of the Engineer in-charge. |
| 79 | Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 - 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge. Antiskid Tiles. Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles. 300 mm x 300 mm in all shades and designs. |
| 80 | Providing and laying 1st class quality vitrified floor tiles in different sizes (thickness to be specified by themanufacturer) with water absorption less than 0.08% and conforming to IS: 15622 - 2017, of approved make, in all colours and shades, laid over 20mm thick cement mortar 1:4 (1 cement : 4 fine sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. all complete as per direction of the Engineer-in-charge.. Glazed Vitrified Tiles (Glossy / Mat Finish/ Anti-Skid).Size of tile 600 mm x 600 mm. |
| 81 | ProvidingandfixingPrecastchequeredcementconcrete tiles18mmthick, laid in footpath&courtyard, on 20 mm thick bed of cementmortar1:4(1cement :4fine sand) jointedwithneatcementslurryincludingrubbing and cleaning etc. all complete as per direction of Engineer-in-charge. In dark shade using ordinary cement |
| 82 | Supplying and installing of wooden (BWF) approved Teak Wood, 21mm imported Teak Flooring, 70 X 40mm pine runner random length anti treated sleepers, 19 mm air crush rubber pad) sports Flooring system complete as specified and as directed by the Engineer-in-Charge |
| 83 | Supply & installation of pre painted Galvalume sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) in 550mpa steel grade, made out of Cold rolled steel coated with Znic-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to ASTM A 792/A782M, ASTM A90/A90M, ASTM AS 1937, ASTM A924/A92M, Alloy coating AZ150/AZ100, colour coated with high quality polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal or with polymer coated J or L hooks, bolts and nuts 8mm diameter with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete upto any pitch in horizontal/ vertical or curved surfaces excluding the cost of purlins,rafters and trusses and including cutting to size and shape wherever required.a) 0.60mm thickness. |
| 84 | Providing and fixing Industrial TURBO ROOF VENTILATOR throat diameter 600 mm with stainless steel polished, Non Power Driven on Roof mounted over Polycarbonate skylight sheet for entering day light complete as specified and as directed by the Engineer-in-Charge |
| 85 | Supply & installation of pre-painted Galvalume sheets roofing accessories in 550mpa steel steel grade, made out of Cold rolled steel coated with Zinc-Aluminium alloy coating of 43.5% Zn, 55% Al and 1.5% Silicon confirming to AASTM A792/A792M and AS1397, Alloy coating AZ150/AZ70, colour coated with high quality polyester coating, top coated of modified polyester of 20 micron, back side coat of 5 micron, having epoxy primer coat of 5 micron on both side etc. complete as per direction of Engineer-in-charge. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. Sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation. The sheet shall be fixed using self drilling /self tapping screws with EPDM washers complete Ridges/Valley/Gutter/Flashing of width 610mm, 0.60mm thickness |
| 86 | Extra for providing and fixing wind ties of 40x 6 mm flat iron section. |
| 87 | 6 mm cement plaster of mix : Cement mortar 1:3 (1 cement : 3 fine sand). For all floor |
| 88 | Neat Cement punning |
| 89 | 12 mm cement plaster in single coats Cement mortar 1:3 (1 cement : 3 fine sand). For all floor |
| 90 | 15 mm cement plaster on the rough side of single or half brick wall of mix: Cement mortar 1:3 (1 cement : 3 fine sand) |
| 91 | Providing and applying white cement based putty ofaverage thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 92 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm |
| 93 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture |
| 94 | Varnishing with varnish of approved brand and mamufacturer [Payment shall be made after submission of Test Certificate issued by the Manufacturer]. Two or more coats of glue with spar varnish over an under coat of flatting varnish. |
| 95 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture |
| 96 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineer incharge. (Glazing and paneling and dash fasteners to be paid for separately) :- Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 97 | For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required. Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 98 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm ) |
| 99 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 100 | Providing and fixingwhite viterous china pedestal type water closet (Europena type WC pan) with seat & lid, 10 ltr. low level white PVC fklushing cistern & CP flush bend with fittings & CI brackets, 40 mm flush bend, overflow arrangement with special of standard make & mosquito proof coupling of approved municipal design complete including painting of fittings & brackets, cutting & making good the walls & floors wherever required. WC pan with ISI marked white solid plastic seat & lid |
| 101 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x400 mm with single 15mm C.P. brass pillar tap. |
| 102 | Providing and fixing PTMT Waste Coupling for washbasin and sink, of approved quality and colour. Waste coupling 38mm of 83mm length and 77mm breadth, weighing not less than 60gms. |
| 103 | Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 38mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 263gms. |
| 104 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 40 mm dia |
| 105 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: (a) 100 mm inlet and 100 mm outlet. Sand Cast Iron S&S as per IS: 1729. |
| 106 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: (b) 100 mm inlet and 75 mm outlet. Sand Cast Iron S&S as per IS- 1729. |
| 107 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 108 | Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan. |
| 109 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge |
| 110 | Providing and fixing on wall face unplasticised Rigid PVC soil, waste & vent pipes (working pressure 4 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: Single socketed pipe - 75 mm OD |
| 111 | Providing and fixing on wall face unplasticised Rigid PVC soil, waste & vent pipes (working pressure 4 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: Single socketed pipe - 110 mm OD |
| 112 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Single unequal junction of required degree with door. 110x110x75 mm |
| 113 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Plain Shoe. 75 mm |
| 114 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Coupler. 110 mm |
| 115 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Terminal Guard. 75mm |
| 116 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Terminal Guard. 110mm |
| 117 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:. Double equal junction of required degree with door. 110x110x110 x110 mm |
| 118 | Providing and fixing 25mm x 1.40 mm clips made out of aluminium strip of approved design to unplasticised - PVC soil, waste & vent pipes by means of Plastic Wall Plugs fitted in the brick work/R.C.C work by drilling with the help of mechaine and screwed with M.S. screws of required length and making good the wall etc.complete. 75mm |
| 119 | Providing and fixing 25mm x 1.40 mm clips made out of aluminium strip of approved design to unplasticised - PVC soil, waste & vent pipes by means of Plastic Wall Plugs fitted in the brick work/R.C.C work by drilling with the help of mechaine and screwed with M.S. screws of required length and making good the wall etc.complete. 110mm |
| 120 | Providing and fixing to the inlet mouth of soil, waste & vent pipes pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. complete. 75mm |
| 121 | Providing and fixing to the inlet mouth of soil, waste & vent pipes pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. complete. 110mm |
| 122 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 15 mm nominal outer dia .Pipes. |
| 123 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 20 mm nominal outer dia .Pipes. |
| 124 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 25 mm nominal outer dia .Pipes. |
| 125 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 40 mm nominal outer dia .Pipes. |
| 126 | Providing and fixing brass bib cock of approved quality : 15mm Nominal Bore |
| 127 | Providing and fixing brass stop cock of approved quality : (a) 15mm Nominal Bore |
| 128 | Providing and fixing brass stop cock of approved quality : (b) 20mm Nominal Bore |
| 129 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 25 mm nominal bore |
| 130 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 40 mm nominal bore |
| 131 | Providing and Fixing C.P. brass shower rose with 15mm or 20mm inlet. (A) 100mm dia. Each |
| 132 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. (a) 15mm Nominal Bore |
| 133 | Providing and fixing PTMT stop cock of approvedquality and colour. 15 mm nominal bore, 86mm long, weighing not less than 88 grams. |
| 134 | Providing and placing on terrace (at all floor levels)polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 135 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 1st class bricks in cement mortar 1:4 (1 cement : 4 fine sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 fine sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design : Extra for depth beyond 450 mm of brick masonry chamber for underground C.I. inspection chamber with same specification as mentioned in item no 20.330 complete as per standard design : Inside dimensions 455x610 mm and 45 cm deep for single pipe line : |
| 136 | Extra for depth beyond 450 mm of brick masonry chamber for underground C.I. inspection chamber with same specification as mentioned in item no 20.330 complete as per standard design :For 500x700 mm size. |
| 137 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with well burnt 2nd class bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 138 | Compacting Original Ground (i) Compacting original ground supporting subgrade Loosening of the ground upto a level of 500 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of Tables 300.2 for subgrade construction as per MoRT&H Technical Specification clauses of section 300. |
| 139 | 80 mm thick factory made c.c. interlocking paver block of M-35 Grade Providing and laying factory made chamfered edge Cement Concrete paver blocks of required strength, thickness & size/ shape, made by table vibratory method to attain superior smooth finish using PU or equivalent moulds, laid in required grey colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per specifications & approval/ direction of the Engineer -in-Charge: (a) 80 mm thick c.c. paver block of M-35 grade with approved colour, design and pattern. |
| 140 | Supplying assembling boring / drilling bore well of 150 - 200 mm dis & lowering 75mm dia PVC (oriplast brand or equivalent ) casting pipe including 75 mm dian strainer pipe (at least 5 X 10 = 50ft ) including 32mm PVC (oriplast or equivalent ) column pipe including necessary clamp, well cap head base socket point safety wire bend etc. complete including gravels size range 5-10 mm (atleast 0.50mm). (payment should be made for successfull boring only for the length of casing pipe & Strainer pipe) etc complete as specified and as directed by the Engineer-in-Charge. |
| 141 | Supply and installing 1HP 15 Stage 3\\" 1Phase Water Filled Borewell Submersible Pump (KS3D-1015, Kirloskar or equivalent ) including Control panel and necessary 2.5sqmm pvc insulated three core flat copper wire including fitting fixing and lowering etc complete as specified and as directed by the Engineer-in-Charge. |
| 142 | Providing and fixing sports arena HDPE Blow Moulded Plastic Chair or equivalent , Aluminum Pressure die casting stand or metal stand with powder coated finish Plastic Material will be UV resisted.Fitting with anchor fastener of Size M8 x 75 MM. all complete as specified and as directed by the Engineer-in-Charge |
| 143 | Construction of International size Swimming Pool at Bholagiri Ground, near TUDA Housing Complex,Agartala, West Tripura. |
| 144 | Clearing grass and removal of the rubbish upto a distance of 50 m outside the periphery of the area cleared |
| 145 | Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep anddisposal of rubbish, lead upto 50 m and lift upto 1.5 m. |
| 146 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed. for all kind of Soil |
| 147 | Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan) including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kind of soil |
| 148 | In or under water and/ or liquid mud, including pumping out water as required. |
| 149 | Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m. All kind of soil |
| 150 | Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. |
| 151 | Supplying and filling in plinth, under floor, foundations etc. with sand (fine) from local quarry with all lifts including spreading in horizontal layers, watering, grading to required slope, ramming, consolidating and compacting each layer by using plate compactor or by any suitable method complete |
| 152 | Supplying chemical emulsion in sealed containers including delivery as specified. |
| 153 | Chlorpyriphos/Lindane emulsifiable concentrate of 20% |
| 154 | Treatment of soil under plinth filling using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with sand filling: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration |
| 155 | Providing and laying in position cement concrete of specified grade excluding the cost of centring andshuttering --All work upto plinth level:1:3:6 ( 1 Cement: 3 fine sand : 6 graded well burnt brick aggregate 40 mm nominal size) |
| 156 | Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to site of laying but excluding the cost of centring, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per the direction of Engineer-in-Charge. (Note :- Cement content considered in this item is @ 418 kg/cum. Excess/ less cement used as per design mix is payable/recoverable separately). All works upto plinth level Reinforced cement concrete grade M-25 using 418 kg of cement per cum |
| 157 | Reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more |
| 158 | Centering shuttering including struttings, propping etc. and removal of form work for: Suspended floors, roofs, landings, balconies and access platform with 12 mm thick shuttering ply. For all floors |
| 159 | First class brick work in superstructure above plinth level & upto floor-five level including cost of all materials as required complete:- In cement mortar 1:5 ( 1 cement : 5 fine sand ). |
| 160 | Providing and laying Polished Granite stone flooring and sill jambs in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 fine sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18 mm thick stone slab |
| 161 | Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framedand fixed in position : Local Teak Wood |
| 162 | Providing and fixing Fiber Glass Reinforced plastic (FRP) Door Frames of cross-section 90mm x 45mm having single rebate of 32mm x 15mm to receive shutter of 30mm thickness .The laminate shall be molded with fire resistant grade unsaturated polyester resin and chopped mat .Doorframe laminate shall be 2mm thick and shall be filled with suitable wooden block in all the three legs. The frame shall be covered with fibreglass from all sides. MS stay shall be provided at the bottom to steady the frame |
| 163 | Providing and fixing ISI marked flush door shutters conforming to IS: 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 164 | Providing and fixing ISI marked oxidised M.S. door latches conforming to IS:5930 with screws etc. complete :300 x 20 x 6 mm |
| 165 | Providing and fixing to existing door frames 30 mm thick Glass Fibre Reinforced Plastic (FRP) panelled door shutter of required colour and approved brand and manufacture, made with fire - retardant grade unsaturated polyester resin, moulded to 3 mm thick FRP laminate for forming hollow rails and styles, with wooden frame and suitable blocks of seasoned wood inside at required places for fixing of fittings, cast monolithically with 5mm thick FRP laminate for panels confirming to TADS 6: 1993 and / or IS: 14856 - 2000 including fixing to frames |
| 166 | Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete. 125 mm |
| 167 | Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square orround bars etc. all complete. |
| 168 | Providing structural steel work in single section fixed with or without connecting plate including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete as required. For all floors |
| 169 | Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes Kg. |
| 170 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 171 | Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm at 100 mm centre to centre and braced with flat iron diagonals 20x5mm sizewith top and bottom rail of T-iron 40x40x6mm with 40mm dia. steel pulleys & with riveted bolts, nuts, locking arrangement, stoppers, handles, hold fast /anchor bolt including embedding in cement concrete of required grade for fixing in position, all necessary fittings, including applying a priming coat of approvedsteel primer etc. complete as required. |
| 172 | Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour,design, fixing in customize design etc. all complete as per direction of Engineer-in- Charge. The glass mosaic tiles tobe fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm andgrouting of the same. The rate is inclusive of all operation, material and required pattern approved byEngineer-in-Charge |
| 173 | Providing and laying 1st class quality ceramic floor tiles in different sizes (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 - 2017 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid over 20 mm thick cement mortar 1:4 (1 cement : 4 fine sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc. all complete as per direction of the Engineer in-charge. Antiskid Tiles. Mat Finish Tiles/ Anti-skid Tiles/ Glossy Tiles. 300 mm x 300 mm in all shades and designs. |
| 174 | 6 mm cement plaster of mix : Cement mortar 1:3 (1 cement : 3 fine sand). For all floor |
| 175 | Neat Cement punning |
| 176 | 12 mm cement plaster in single coats Cement mortar 1:3 (1 cement : 3 fine sand). For all floor |
| 177 | 15 mm cement plaster on the rough side of single or half brick wall of mix: Cement mortar 1:3 (1 cement : 3 fine sand) |
| 178 | Providing and applying white cement based putty ofaverage thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 179 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @ 0.75 ltr /10 sqm |
| 180 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture |
| 181 | Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications [Payment shall be made after submission of Test Certificate issued by the Manufacturer]: Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture |
| 182 | Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixing with dash fasteners of required dia and size, including necessary filling up of gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawing and the direction of Engineer incharge. (Glazing and paneling and dash fasteners to be paid for separately) :- Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 183 | For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing fittings wherever required including the cost of EPDM rubber / neoprene gasket required. Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15). |
| 184 | Providing and fixing glazing of approved quality in aluminium doors, windows, ventilator, shutters and partition etc. with EPDM rubber / neoprene gasket etc. complete as per architectural drawing and the direction of Engineer-in-charge (Cost of snap beading shall be paid in basic item) With float glass panes of 4.0 mm thickness ( weight not less than 10.0 kg / sqm ) |
| 185 | Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete including cutting and making good the walls and floors wherever required : White Vitreous china Orrisa pattern W.C. pan of size 580x440 mm with integral type foot rests. |
| 186 | Providing and fixingwhite viterous china pedestal type water closet (Europena type WC pan) with seat & lid, 10 ltr. low level white PVC fklushing cistern & CP flush bend with fittings & CI brackets, 40 mm flush bend, overflow arrangement with special of standard make & mosquito proof coupling of approved municipal design complete including painting of fittings & brackets, cutting & making good the walls & floors wherever required. WC pan with ISI marked white solid plastic seat & lid |
| 187 | Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: White Vitreous China Flat back wash basin size 550x400 mm with single 15mm C.P. brass pillar tap. |
| 188 | Providing and fixing PTMT Waste Coupling for washbasin and sink, of approved quality and colour. Waste coupling 38mm of 83mm length and 77mm breadth, weighing not less than 60gms. |
| 189 | Providing and fixing PTMT Bottle Trap for Wash basin and sink. Bottle trap 38mm single piece moulded with height of 270mm, effective length of tail pipe 260mm from the centre of the waste coupling 77mm breadth with 25mm minimum water seal, weighing not less than 263gms. |
| 190 | Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Flexible pipe 40 mm dia |
| 191 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: (a) 100 mm inlet and 100 mm outlet. Sand Cast Iron S&S as per IS: 1729. |
| 192 | Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: (b) 100 mm inlet and 75 mm outlet. Sand Cast Iron S&S as per IS- 1729. |
| 193 | Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. |
| 194 | Providing and fixing G.I. inlet connection for flush pipe connecting with W.C. pan. |
| 195 | Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge |
| 196 | Providing and fixing on wall face unplasticised Rigid PVC soil, waste & vent pipes (working pressure 4 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: Single socketed pipe - 75 mm OD |
| 197 | Providing and fixing on wall face unplasticised Rigid PVC soil, waste & vent pipes (working pressure 4 kg / cm2) conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion: Single socketed pipe - 110 mm OD |
| 198 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Single unequal junction of required degree with door. 110x110x75 mm |
| 199 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Plain Shoe. 75 mm |
| 200 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Coupler. 110 mm |
| 201 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Terminal Guard. 75mm |
| 202 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion. Terminal Guard. 110mm |
| 203 | Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC soil, waste & vent pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion:. Double equal junction of required degree with door. 110x110x110 x110 mm |
| 204 | Providing and fixing 25mm x 1.40 mm clips made out of aluminium strip of approved design to unplasticised - PVC soil, waste & vent pipes by means of Plastic Wall Plugs fitted in the brick work/R.C.C work by drilling with the help of mechaine and screwed with M.S. screws of required length and making good the wall etc.complete. 75mm |
| 205 | Providing and fixing 25mm x 1.40 mm clips made out of aluminium strip of approved design to unplasticised - PVC soil, waste & vent pipes by means of Plastic Wall Plugs fitted in the brick work/R.C.C work by drilling with the help of mechaine and screwed with M.S. screws of required length and making good the wall etc.complete. 110mm |
| 206 | Providing and fixing to the inlet mouth of soil, waste & vent pipes pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. complete. 75mm |
| 207 | Providing and fixing to the inlet mouth of soil, waste & vent pipes pipe PTMT grating with thickness of 8mm and weighing not less than 100gm. complete. 110mm |
| 208 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 15 mm nominal outer dia .Pipes. |
| 209 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 20 mm nominal outer dia .Pipes. |
| 210 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 25 mm nominal outer dia .Pipes. |
| 211 | Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cementand testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall. 40 mm nominal outer dia .Pipes. |
| 212 | Providing and fixing brass bib cock of approved quality : 15mm Nominal Bore |
| 213 | Providing and fixing brass stop cock of approved quality : (a) 15mm Nominal Bore |
| 214 | Providing and fixing brass stop cock of approved quality : (b) 20mm Nominal Bore |
| 215 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 25 mm nominal bore |
| 216 | Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 40 mm nominal bore |
| 217 | Providing and Fixing C.P. brass shower rose with 15mm or 20mm inlet. (A) 100mm dia. Each |
| 218 | Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. (a) 15mm Nominal Bore |
| 219 | Providing and fixing PTMT stop cock of approvedquality and colour. 15 mm nominal bore, 86mm long, weighing not less than 88 grams. |
| 220 | Providing and placing on terrace (at all floor levels)polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. |
| 221 | Constructing brick masonry chamber for underground C.I. inspection chamber and bends with 1st class bricks in cement mortar 1:4 (1 cement : 4 fine sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) R.C.C. top slab with 1:2:4 mix (1 cement :2 fine sand : 4 graded stone aggregate 20 mm nominal size) foundation concrete 1:5:10 (1 cement: 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement: 3 fine sand) finished smooth with a floating coat of neat cement on walls and bed concrete etc.complete as per standard design :Inside dimensions 455x610 mm and 45 cm deepfor single pipe line : |
| 222 | Extra for depth beyond 450 mm of brick masonry chamber for underground C.I. inspection chamber with same specification as mentioned in item no 20.330 complete as per standard design :For 500x700 mm size. |
| 223 | Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with well burnt 2nd class bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. |
| 224 | Compacting Original Ground (i) Compacting original ground supporting subgrade Loosening of the ground upto a level of 500 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of Tables 300.2 for subgrade construction as per MoRT&H Technical Specification clauses of section 300. |
| 225 | 80 mm thick factory made c.c. interlocking paver block of M-35 Grade Providing and laying factory made chamfered edge Cement Concrete paver blocks of required strength, thickness & size/ shape, made by table vibratory method to attain superior smooth finish using PU or equivalent moulds, laid in required grey colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand in footpath, parks, lawns, drive ways or light traffic parking etc. all complete as per specifications & approval/ direction of the Engineer -in-Charge: (a) 80 mm thick c.c. paver block of M-35 grade with approved colour, design and pattern. |
| 226 | Providing and laying flat brick soling layer on prepared subgrade according to lines, grades and cross-sectionshown on the drawing, filling joints with Earth, free from clay with a Plasticity Index not exceeding 6, watering androlling the same with three wheeled road roller 80-100 kN as per MoRD Technical Specification Clause 412. |
| 227 | Supplying and laying Polythene Sheet (150 gm / sq.m.) over damp proof course or below flooring or roof terracing or in foundation or in foundation trenches. all complete as per specification and direction of the Engineer - in - charge. |
| 228 | Construction of Single-Storeyed RCC Framed Pump House (50 HP Capacity) on Turnkey BasisConstruction of a single-storeyed RCC framed Pump House (50 HP Capacity) on a turnkey basis, including survey, planning, structural design, preparation of detailed working drawings, obtaining approval of drawings from the Engineer-in-Charge before commencement of work, excavation, all foundations, RCC substructure, superstructure, RCC floor and roof slab, brick masonry, plastering, flooring, stell doors & windows, painting, waterproofing, attached toilet, internal water supply, sanitary installation, septic tank with soak pit, internal electrification, earthing, drainage arrangements, testing, commissioning, and all other allied civil, sanitary and Internal & External electrical works complete in all respects as per approved drawings, relevant IS Codes, technical specifications, and the directions of the Engineer-in-Charge. Mode of Payment : 25% = On completion of foundation works,15% = On completion of substructure works, 25% = On completion of superstructure works,35% = On completion of finishing works, internal electrification, water supply, sanitary installation, septic tank, testing & commissioning, and successful handing over of the completed Pump House.) all complete as per specification and direction of the Engineer - in - charge. |
| 229 | Drilling and boring pilot hole in any soil strata by manualmeans, collection of soil samples of different strata met withduring drilling at various suitable levels, preservation ofsamples in polythene bags / sample boxes and disposal ofexcess soil or mud, including the cost for water etc. asrequired to maintain the pilot hole properly as perspecification and direction of the Engineer - in - charge.i ) 100 mm dia |
| 230 | Reaming of pilot hole to an enlarged bore hole in any soilstrata by manual means, disposal of excess soil or mud,including the cost for water etc. as required to maintain thebore hole properly as per specification and direction of theEngineer - in - charge i ) from 100 mm dia pilot hole to 250 mm bore hole |
| 231 | Providing & lowering of UPVC pipe as per IS:12818 after washing of the bore hole by manual means as per specification and direction of the Engineer - in - charge. |
| 232 | 1) UPVC 'CM' casing pipes |
| 233 | ii)150 mm dia |
| 234 | iii) 100 mm dia |
| 235 | 2) UPVC 'RS' pipes |
| 236 | ii) 100 mm dia |
| 237 | Providing and fixing of UPVC end cap / well cap suitable for UPVC 'CM' casing or 'CS' casing or 'RS' pipes as per specification and direction of the Engineer - in - charge. i) 100 mm dia |
| 238 | Providing and fixing of UPVC reducer suitable for UPVC 'CM' casing or 'CS' casing or 'RS' pipes as per specification and direction of the Engineer - in - charge.i)150 mm x 100 mm dia |
| 239 | Providing and fixing of housing clamp (made with 12 mm thick MS sheet) along with well cap (made with 10 mm thick MS sheet) with necessary arrangements for SBDTW as per specification and direction of the Engineer - in - charge. i) 150 mm dia |
| 240 | Providing and shrouding of the deep tube well assembly with washed pea gravels ( 2.0 - 4.75 mm effective size ) as per specification ( IS : 4097) and direction of the Engineer - in - charge.A. with contractor's rigi) with pea gravels obtained from Durgapur, West Bengal. |
| 241 | Washing and development of tube well by using hand pump or by any suitable method and testing of the well as per specification and direction of the Engineer - in - charge. |
| 242 | Providing and fitting fixing of 6 feet x 4 feet x 1 inch (thickness) Gamair wood / plywood pannel board for fitting fixing of electrical items, in/c 2 nos MS angle post ( size 2 inch x 2 inch x 9 feet ), nuts & bolts etc. for irrection of the same by 1:1.5:3 cement concrete casting ( 1 feet x 1 feet x 2 feet) below the ground level and painting two or more coats & plastic paint as per specification and direction of theEngineer-in-charge. |
| 243 | Supplying and installation of water lubricated submersible pump having ISI marked of capacity 150 LPM at Maximum head up to 78mtr, couple with submersible motor 3HP suitable for 240 volts (+10%) variation single phase 50 HP AC supply DOL starting method to run at 2880 RPM along with 35 mtr 2.5sqm PVC insulated 3 (Three) core flat copper cables including fittings fixing and lowering if with 50mm dia GI pipe upto 100ft (30.00mtr) etc, complete as per direction of the engineering in charge (50 mm dia GI and fitting and copper cable will be paid separately) all complete as per specification and direction of the Engineer - in - charge. |
| 244 | Supplying and installation of Openwell submersible pump having ISI marked of Max. capacity 280 LPM at Max. head up to 21 mtr, couple with submersible motor 2HP suitable for 240 volts (+10%) variation single phase 50 HP AC supply DOL starting method to run at 2880 RPM including fittings fixing with 50mm x 50mm dia pipe upto 100ft (30.00mtr) etc, complete as per direction of the engineering in charge (50 mm x 50mm pipe and fitting will be paid separately) all complete as per specification and direction of the Engineer - in - charge. |
| 245 | Providing and fitting fixing with PVC insulated 3 core flat Copper cable conforming to relevant IS code for submerssible motor with all necessary equipments and fittings as required as per specification and direction of the Engineer-in-charge.i) 2.50 sqmm |
| 246 | Providing, fixing and laying rigid UPVC pipes conforming to IS : 4985 jointing with couplers, of same class conforming to IS : 10124 ( Pt-II ) with solvent cement conforming to IS : 14182 including testing of joints complete ( but excluding the cost of specials like bend, tees etc. which will be paid separately ) as per CPWD specification and direction of the Engineer - in - charge. A) Class - 3 ( working pressure 6.0 kg / cm2)i) 50 mm OD |
| 247 | Providing and fixing G.I. pipes of medim class as per IS :1239 with latest amendment complete with G.I. fittings and clamps, including cutting and making good the walls etc. complete as per CPWD specification and direction of the Engineer - in - charge. |
| 248 | i)15mm Dia |
| 249 | ii)25mm Dia |
| 250 | iii) 40 mm Dia |
| 251 | iv) 50mm Dia |
| 252 | Providing and fixing G.I. Bend /elbow in the pipe line including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge. |
| 253 | i)15 mm dia |
| 254 | ii)25 mm dia |
| 255 | iii)40 mm dia |
| 256 | iv) 50mm Dia |
| 257 | Providing and fixing G.I. equal Tee with the pipe line including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge. |
| 258 | i)15x15x15 mm dia |
| 259 | ii)25x25x25 mm dia |
| 260 | iii)40X40X40 mm dia |
| 261 | iv)50X50X50 mm dia |
| 262 | Providing and fixing G.I. Reducer with the pipe line including testing of joints complete as per CPWD specification and direction of the Engineer - in - charge. |
| 263 | i)40X25mm dia |
| 264 | ii)40x15mm dia |
| 265 | iii)25x15mm dia |
| 266 | Providing and fixing G.I. socket as per CPWD specification and direction of the Engineer - in - charge. |
| 267 | i)15 mm dia |
| 268 | ii)25 mm dia |
| 269 | iii)40 mm dia |
| 270 | iv) 50mm Dia |
| 271 | Providing and fixing G.I. union as per CPWD specification and direction of the Engineer - in - charge. |
| 272 | i)15 mm dia |
| 273 | ii)25 mm dia |
| 274 | iii)40 mm dia |
| 275 | iv) 50mm Dia |
| 276 | Providing and fitting fixing of brass fullway valve with handle in the GI pipe line including cutting, threading etc. complete as per specification and direction of the Engineer - in - charge. |
| 277 | i)50mm Dia |
| 278 | ii)40mm dia |
| 279 | iii)25mm dia |
| 280 | iv) 15mm dia |
| 281 | Supply, Installation, Testing & Commissioning of Totally Non-Corrosive Pressure Sand Filter made of Fiber glass reinforced with Bobbin Wound Polyester Yarn, complete with uPVC/Polypropylene collector arms, Stainless Steel hub, 2000 mm diameter, 1000 mm media bed depth, 500 mm manhole, 140 mm flanged inlet & outlet, pressure gauge, manual air purge arrangement, complete as specified.(Make: Pentair or equivalent company)Working Pressure: 2.5kg/cm2, (37.5 PSI),Test Pressure: 3.75 kg/cm2 (56.25 PSI). Max. Temperature : 43° C / 109° F Flow Rate: 124 m³/hour ,Filtration Velocity : 40 m3/hr/m2,Make: Pentair or equivalent complete as per specification and direction of the Engineer - in - charge. |
| 282 | Supply, Installation, Testing & Commissioning of Valve Battery Manifold made of PVC with PN-10 flanges for connecting to filters, comprising 5 Nos. Butterfly Valves for filtration, backwashing, rinsing and shut-down operations, mounted on 140 mm dia PN-10 PVC pipe, complete with PVC flanges, screws, nuts, washers in zinc-plated steel, zinc-plated steel supports and clamps, including all fittings, erection, testing and commissioning, complete as per CPWD specification and direction of the Engineer - in - charge. |
| 283 | Supply, Installation, Testing & Commissioning of Silica sand media for filter with granulometry between 1.0 and 2.0 mm . complete as per CPWD specification and direction of the Engineer - in - charge.Make: Aqua Planner India_BARAKAR / Global_LOCAL or equivalent |
| 284 | Supply, Installation, Testing & Commissioning of Gravel for filter with granulometry between 12-25 mm. complete as per CPWD specification and direction of the Engineer - in - charge.Make: Aqua Planner India_BARAKAR / Global_LOCAL or equivalent Approved Brand |
| 285 | Supply, Installation, Testing & Commissioning of Self-Priming Monoblock Recirculation Pump with pre-filter, complete with heavy-duty TEFC motor, Cam & Ramp™ lid strainer, suitable for swimming pool filtration system, conforming to the following specifications:(Protection: IP-55 ,Insulation : Class-F ,Speed : 2900 RPM ,Discharge : 35 m³/hr at 10 m head, Voltage : 220–240 V ,Frequency : 50–60 Hz ,Phase : Single Phase ,Motor Rating : 10 HP (7.50 kW), Motor Protection : Heavy-duty TEFC ,Pump Strainer : Cam & Ramp™ Lid and Make: Pentair),Flowrate - 123 m3 / hr @ 12 m.headProtection Class - IP 55,Insulation Class - F,RPM - 2900,Voltage - 230/400V. 50 Hz,Phase - 3 Phase,HP/kW - 10 / 7.5 kW, All complete as per CPWD specification and direction of the Engineer - in - charge.Make: Pentair or equivalent Approved Brand |
| 286 | Supply, Installation, Testing & Commissioning of Chemical Feeder having 11 kg capacity, complete with all accessories, mounting arrangement, PVC connection fittings, valves, clamps, testing and commissioning, as required. All complete as per CPWD specification and direction of the Engineer - in - charge.Make: Aqvastar or Equivalent Capacity: 11 kg |
| 287 | Supply, Installation, Testing & Commissioning of Stainless Steel Square Main Drain Cover & Frame, size 500 × 500 mm, fabricated from corrosion-resistant Stainless Steel, complete with frame, fixing accessories, anchor fasteners, alignment, testing and commissioning, as required.(Make: Pentair or equivalent , Size: 500 × 500 mm and Material: Stainless Steel ) All complete as per specification and direction of the Engineer - in - charge |
| 288 | Supply, Installation, Testing & Commissioning of White ABS Plastic Bottom Inlet for concrete swimming pool, complete with Stainless Steel screws, adjustable flow arrangement, suitable for maximum flow of 11 m³/hr, with 2\\" outside threaded connection and 50 mm inside diameter, including all accessories, fixing, testing and commissioning, All complete as per specification and direction of the Engineer - in - charge |
| 289 | Supply, Installation, Testing & Commissioning of Suction Fitting for swimming pool circulation system, manufactured from high-grade UV-resistant ABS Plastic, complete with fixing accessories, sealing compound, testing and commissioning, conforming to the following specifications:(Size: 50 mm Inner Diameter ,Material: Better Grade ABS Plastic ,Surface: UV Resistant ,Colour: White and Make: Pentair or equivalent ) All complete as per specification and direction of the Engineer - in - charge |
| 290 | Supply, Installation, Testing & Commissioning of Float Line Anchor Cap, manufactured from Electro-Polished Stainless Steel (SS-316), complete with 80 × 80 mm Square Flange, fixing accessories, anchor bolts, alignment, testing and commissioning, as specified. (Material: SS-316 (Electro-Polished) ,Flange Size: 80 × 80 mm and Make: Aqvastar or equivalent ) All complete as per specification and direction of the Engineer - in - charge |
| 291 | Supply, Installation, Testing & Commissioning of Float Line anchors cup made in electropolished SS-316, supllied with Square Flange 80 x 80mm. All complete as per specification and direction of the Engineer - in - charge |
| 292 | Supply, Installation, Testing & Commissioning of Swimming Pool Stainless Steel Ladder, complete with 5 Nos. Anti-slip Treads, anchor sockets, fixing accessories, testing and commissioning, conforming to the following specifications:All complete as per CPWD specification and direction of the Engineer - in - charge(Material (MOC): AISI 304 Stainless Steel,Surface Finish: Bright Polished,No. of Treads: 5 Nos. ,Model: Mixed ,Property: Corrosion Resistant and Make: Pentair or equivalent ) |
| 293 | Supply, Installation, Testing & Commissioning of Swimming Pool Stainless Steel Ladder, complete with 4 Nos. Anti-slip Treads, anchor sockets, fixing accessories, testing and commissioning, conforming to the following specifications:All complete as per CPWD specification and direction of the Engineer - in - charge(Material (MOC): AISI 304 Stainless Steel,Surface Finish: Bright Polished ,No. of Treads: 4 Nos. ,Model: Mixed ,Property: Corrosion Resistant and Make: Pentair or equivalent All complete as per specification and direction of the Engineer - in - charge |
| 294 | Supply, Installation, Testing & Commissioning of Overflow Channel Grating of 295 mm width, manufactured from UV Protected Weatherproof Polypropylene, having heavy-duty non-slip surface with single spine construction, complete with all fixing accessories, supports, cutting to required length, testing and commissioning, as specified.(Width: 295 mm,Material (MOC): UV Protected Weatherproof Polypropylene,Surface: Heavy Duty Non-Slip, Colour: White Spine: Single Spine and Make: Pentair or equivalent ):All complete as per specification and direction of the Engineer - in - charge |
| 295 | Supply, Installation, Testing & Commissioning of Swimming Pool Vacuum Head (Pool Cleaner), fabricated from Stainless Steel, complete with Wishbone Fixing, 750 mm wide cleaning head, clip connection, all accessories, testing and commissioning, suitable for manual swimming pool cleaning operations.(Type: SS Pool Cleaner Vacuum Head ,Head Width: 750 mm ,Fixing: Wishbone Type, Connection: Clip Connection and Material: Stainless Steel )All complete as per CPWD specification and direction of the Engineer - in - charge |
| 296 | Supply of Swimming Pool Trailing Cable, suitable for manual swimming pool cleaning equipment/vacuum system, heavy-duty flexible, waterproof, UV-resistant, complete as specified.(Approved Make: Pentair / Emaux / Aqvastar or approved equivalent)All complete as per CPWD specification and direction of the Engineer - in - charge |
| 297 | Supply, Installation, Testing & Commissioning of Extensible Handle for swimming pool cleaning attachments, manufactured from high-strength anodized aluminium, telescopic type, extendable up to 9.0 metres, compatible with the complete range of standard pool cleaning accessories, including assembly, testing and commissioning.(Material: Anodized Aluminium ,Length: Extendable up to 9.0 m ,Application: Suitable for vacuum head, brush, leaf skimmer and other cleaning attachments and Make: Pentair or approved equivalent) All complete as per specification and direction of the Engineer - in - charge |
| 298 | Supply, Installation, Testing & Commissioning of Blue Colour Floating Vacuum Hose, 38 mm diameter, 30 metres long, complete with hose cuffs/connectors for connection to suction inlet, suitable for swimming pool cleaning system, including all accessories, testing and commissioning.(Type: Floating Vacuum Hose,Diameter:38 mm, Length: 30 metres ,Colour: Blue ,Accessories: Hose Cuffs/Connectors Make: Pentair or approved equivalent) All complete as per specification and direction of the Engineer - in - charge |
| 299 | Supply, Installation, Testing & Commissioning of Deep Leaf Net for swimming pool cleaning, heavy-duty UV-resistant frame with deep mesh net, suitable for attachment with telescopic handle, complete with fixing arrangement and accessories.Make:(Pentair or approved equivalent) All complete as per CPWD specification and direction of the Engineer - in - charge |
| 300 | Supply, Installation, Testing & Commissioning of Curved Swimming Pool Brush, 450 mm wide, manufactured from heavy-duty Polypropylene, suitable for cleaning pool basin, walls and scum line, complete with handle clip, fixing accessories, testing and commissioning.(Type: Curved Pool Cleaning Brush ,Width: 450 mm,Material: Polypropylene ,Application: Pool Basin & Scum Line Cleaning and Make: Pentair or approved equivalent) All complete as per specification and direction of the Engineer - in - charge |
| 301 | Supply, Installation, Testing & Commissioning of Reinforced Aluminium Telescopic Pole/Handle, 4.8 m long, manufactured from high-strength anodized aluminium, suitable for attachment with vacuum head, leaf skimmer, curved brush and other swimming pool cleaning accessories, complete with locking mechanism, accessories, testing and commissioning.(Type: Telescopic Pole ,Material: Reinforced Anodized Aluminium ,Length: 4.8 metres ,Application: Swimming Pool Cleaning Accessories and Make:( Pentair or approved equivalent) All complete as per specification and direction of the Engineer - in - charge |
| 302 | Supply, Installation, Testing & Commissioning of 18\\" Algae Brush with Aluminum Back and Stainless-Steel Bristles (Make: Pentair or approved equivalent), complete with all accessories, including transportation, loading, unloading, installation, testing and commissioning, complete in all respects. All complete as per specification and direction of the Engineer - in - charge |
| 303 | Supply, Installation, Testing & Commissioning of Swimming Pool Water Test Kit for measurement of Free Chlorine and pH, complete with comparator, reagent bottles, testing accessories, carrying case, instruction manual, initial calibration/checking and commissioning.(Type: Water Quality Test Kit,Parameters: Free Chlorine & pH,Make: Pentair (or Approved Equivalent brand) All complete as per specification and |
| 304 | Supply & Commissioning of Trichloroisocyanuric Acid (TCCA) Granules containing 90% Free Available Chlorine, suitable for swimming pool water disinfection, complete with handling, initial dosing, testing and commissioning, as specified.(Chemical: Trichloroisocyanuric Acid (TCCA) Granules,Available Chlorine: 90% and Make: China / Local (Approved Equivalent)) All complete as per CPWD specification and direction of the Engineer - in - charge |
| 305 | Supply & Commissioning of Ammonium Alum (Coagulant) for swimming pool water treatment, complete with transportation, handling, initial dosing, testing and commissioning, as specified.(Chemical: Ammonium Alum and Make: Local (Approved Equivalent)) All complete as per CPWD specification and direction of the Engineer - in - charge |
| 306 | Supply & Commissioning of Sodium Carbonate (Soda Ash) for swimming pool water treatment and pH adjustment, complete with transportation, handling, initial dosing, testing and commissioning, as specified.(Chemical: Sodium Carbonate (Soda Ash) ,Grade: Technical Grade and Make: API / Local (Approved Equivalent)) All complete as per CPWD specification and direction of the Engineer - in - charge |
| 307 | Supply, Installation, Testing & Commissioning of Horizontal Centrifugal Suction Pump with inbuilt strainer, complete with motor, base frame, accessories, foundation bolts, electrical connections, testing and commissioning, conforming to the following specifications:(Type: Horizontal Centrifugal Pump with Inbuilt Strainer ,Protection Class: IP-55 ,Insulation Class: Class-F, Speed: 2900 RPM,Discharge: 24 m³/hr at 12 m Head ,Voltage: 220–240 V, 50 Hz ,Phase: Single Phase ,Motor Rating: 2 HP (1.5 kW) and Make: Aqvastar .Protection Class - IP 55,Insulation Class - F,RPM - 2900Flowrate - 24 m3 / hr @ 12 m.head,Voltage - 220/240V. 50 Hz,Phase - I Phase,HP / kW - 2 /1.5 All complete as per CPWD specification and direction of the Engineer - in - charge |
| 308 | Supply, Installation, Testing & Commissioning of Electrical Control Panel for complete swimming pool operation, including control and protection of re-circulation pumps (05 Nos.), underwater pool lights (40 Nos.), chemical dosing pumps, and all other electrically operated pool equipment. The scope shall include supply, installation, internal wiring, MCCBs/MCBs, contactors, overload relays, timers, selector switches, indicating lamps, voltmeter, ammeter, busbars, cable terminations, earthing, testing and commissioning, complete as specified.The contractor's scope shall also include all electrical connections/electrification of:(Re-circulation Pumps:05 Nos.,Underwater Pool Lights:40 Nos.,Chemical Dosing Pumps,Other Pool Equipment,Electrical Control Panel with all protection devices,Necessary circuit breakers of approved make,Internal wiring, gland, lugs and accessories) All complete as per CPWD specification and direction of the Engineer - in - charge |
| 309 | Supply, Installation, Testing & Commissioning of Electrical Flexible Copper Cable for swimming pool pumps, 6.0 sq.mm × 6 Core, PVC insulated, PVC sheathed, FRLS, suitable for power connection to pool pumps, complete with cable glands, lugs, ferrules, terminations, testing and commissioning.(Type: Flexible Copper Cable,Size: 6.0 sq.mm × 6 Core,Conductor: Electrolytic Copper,Insulation: PVC / FRLS ,Make: KEI (or approved equivalent) ) All complete as per CPWD specification and direction of the Engineer - in - charge |
| 310 | Supply, Installation, Testing & Commissioning of Electrical Flexible Copper Cable for Vacuum Pump, 2.5 sq.mm × 3 Core, PVC insulated, PVC sheathed, FRLS, complete with cable glands, lugs, ferrules, terminations, testing and commissioning.(Type: Flexible Copper Cable,Size: 2.5 sq.mm × 3 Core,Conductor: Electrolytic Copper,Insulation: PVC / FRLS ,Make: KEI (or approved equivalent) ) All complete as per CPWD specification and direction of the Engineer - in - charge |
| 311 | Supply, Installation, Testing & Commissioning of Swimming Pool Starting Block, manufactured with Electropolished AISI 316 Stainless Steel Stand and 50 cm × 50 cm FRP Anti-Slip Platform, complete with stainless steel hand grips for backstroke start, anchor fasteners, base plate, fixing accessories, testing and commissioning, conforming to FINA specifications.(Type: Starting Block,Platform Size: 500 mm × 500 mm ,Platform Material: FRP with Anti-Slip Surface,Stand Material: Electropolished AISI 316 Stainless Steel,Height: 750 mm,Accessories: Stainless Steel Hand Grips for Backstroke,Specification: FINA Compliant and Make: Aqvastar (or approved equivalent)) All complete as per CPWD specification and direction of the Engineer - in - charge |
| 312 | Supply, Installation, Testing & Commissioning of High Quality \\"Anti-Wave MAXI\\" Float Lane, complete with chemical-resistant floats, 50 m length, 150 mm diameter discs, assembled on 5 mm dia SS-316 wire rope, complete with SS-316 tension spring, tensioner, end fittings and accessories, in Blue, Red, Yellow and Green colours as per FINA Rules, including installation, testing and commissioning.(Type: Anti-Wave MAXI Float Lane,Length: 50 m,Disc Diameter: 150 mm,Wire Rope: 5 mm dia SS-316,Accessories: SS Spring, Tensioner, End Fittings,Colour: Blue / Red / Yellow / Green (As per FINA Rules) andMake: Aqvastar (or approved equivalent) All complete as per CPWD specification and direction of the Engineer - in - charge |
| 313 | Supply, Installation, Testing & Commissioning of Stainless Steel Float Lane Storage Caddy / Roller, suitable for storage of 4 Nos. × 50 m Swimming Pool Float Lanes, fabricated from heavy-duty corrosion-resistant Stainless Steel frame complete with roller assembly, swivel castor wheels, supports, fasteners and accessories, including installation, testing and commissioning.(Type: Float Lane Storage Caddy / Roller,Capacity: 4 × 50 m Float Lanes, Material: Stainless Steel,Application: Storage and transportation of swimming pool float lanes, Make: Aqvastar (or approved equivalent) All complete as per CPWD specification and direction of the Engineer - in - charge |
| 314 | Supply, Installation, Testing & Commissioning of uPVC/PP pipes of minimum PN-10 pressure rating, including all standard fittings such as bends, elbows, tees, reducers, couplers, unions, sockets, end caps, solvent cement, clamps, supports and all other accessories required for complete installation. Where special fittings are required and are not available in the Indian market, the same shall be fabricated from high-grade chopped PVC fibre/rovings capable of withstanding a minimum working pressure of 10 kg/cm².All complete as per CPWD specification and direction of the Engineer - in - charge |
| 315 | The item shall include laying, alignment, jointing, fixing with suitable supports/clamps, pressure testing at 10 kg/cm² for 24 hours, flushing, testing and commissioning, complete in all respects as directed by the Engineer-in-Charge. |
| 316 | (a) 315 mm dia. |
| 317 | (b) 200 mm dia. |
| 318 | ( c ) 150 mm dia. |
| 319 | (d) 110 mm dia. |
| 320 | ( e ) 90 mm dia. |
| 321 | (f) 75 mm dia. |
| 322 | (g) 63 mm dia. |
| 323 | (h) 50 mm dia. |
| 324 | Supply, Installation, Testing & Commissioning of 200 mm dia uPVC/PP Pipe (PN-6 / 6 kg/cm² Pressure Rating), including all standard fittings such as bends, elbows, tees, reducers, couplers, unions, sockets, solvent cement, clamps, supports and all other accessories required for complete installation. The item shall include laying, alignment, jointing, fixing with suitable supports/clamps, pressure testing at 6 kg/cm², flushing, testing and commissioning, complete in all respects as directed by the Engineer-in-Charge. |
| 325 | Supply, Installation, Testing & Commissioning of PVC-U Ball Valve, 160 mm diameter, complete with solvent socket metric connections, EPDM \\"O\\" rings, HDPE ball seats, testing and commissioning, conforming to the following specifications:(Diameter: 160 mm,Working Pressure: PN-10 (150 psi),Maximum Operating Temperature: 20°C (73°F) ,Body Material: PVC-U,O-Ring: EPDM,Ball Seats: HDPE ,Standard: ASTM / British Standard,Connection: Solvent Socket (Metric) and Make: Cepex or Approved equivalent Brand ) complete in all respects as directed by the Engineer-in-Charge. |
| 326 | Supply, Installation, Testing & Commissioning of PVC-U Ball Valve, 110 mm diameter, complete with solvent socket metric connections, EPDM \\"O\\" rings, HDPE ball seats, testing and commissioning, conforming to the following specifications (Diameter: 110 mm,Working Pressure: PN-10 (150 psi),Maximum Operating Temperature: 20°C (73°F) ,Body Material: PVC-U,O-Ring: EPDM,Ball Seats: HDPE,Standard: ASTM / British Standard,Connection: Solvent Socket (Metric), Make: Cepex or Approved equivalent Brand ) complete in all respects as directed by the Engineer-in-Charge. |
| 327 | Supply, Installation, Testing & Commissioning of PVC-U Ball Valve, 75 mm diameter, complete with solvent socket metric connections, EPDM \\"O\\" rings, HDPE ball seats, testing and commissioning, conforming to the following specifications (Diameter: 75 mm,Working Pressure: PN-10 (150 psi),Maximum Operating Temperature: 20°C (73°F),Body Material: PVC-U,O-Ring: EPDM,Ball Seats: HDPE,Standard: ASTM / British Standard,Connection: Solvent Socket (Metric) and Make: Cepex or Approved equivalent Brand ) complete in all respects as directed by the Engineer-in-Charge. |
| 328 | Supply, Installation, Testing & Commissioning of PVC-U Ball Valve, 63 mm diameter, complete with solvent socket metric connections, EPDM \\"O\\" rings, HDPE ball seats, testing and commissioning, conforming to the following specifications (Diameter: 63 mm,Working Pressure: PN-10 (150 psi),Maximum Operating Temperature: 20°C (73°F) ,Body Material: PVC-U,O-Ring: EPDM,Ball Seats: HDPE,Standard: ASTM / British Standard,Connection: Solvent Socket (Metric) and Make: (Cepex or Approved equivalent Brand ) complete in all respects as directed by the Engineer-in-Charge. |
| 329 | Supply, Installation, Testing & Commissioning of EPDM Wafer Type / Dual Plate Type Check Valve, 160 mm diameter, complete with EPDM seat, dual stainless steel plates, fasteners, gaskets, installation, testing and commissioning, suitable for water circulation systems (Type: Wafer Type / Dual Plate Check Valve,Size: 160 mm,Seat Material: EPDM,Body: Cast Iron / Ductile Iron (Epoxy Coated),Disc: Stainless Steel,Pressure Rating: PN-10 / PN-16 nd Application: Swimming Pool Filtration System. complete in all respects as directed by the Engineer-in-Charge. |
| 330 | Supply, Installation, Testing & Commissioning of Non-Return Valve (NRV) – EPDM Wafer Type / Dual Plate Type Check Valve, 75 mm diameter, complete with EPDM seat, stainless steel dual plates, gaskets, fasteners, installation, testing and commissioning, suitable for swimming pool filtration and circulation system (Type: Wafer Type / Dual Plate Check Valve (Non-Return Valve),Size: 75 mm,Seat Material: EPDM,Body: Cast Iron / Ductile Iron (Epoxy Coated),Disc: Stainless Steel,Pressure Rating: PN-10 / PN-16 and Application: Swimming Pool Filtration & Water Circulation System) complete in all respects as directed by the Engineer-in-Charge. |
| 331 | Supply, Installation, Testing & Commissioning of EPDM Flange Adaptor Set, complete with 160 mm dia PVC/UPVC Flange Adaptor, EPDM gasket, galvanized/stainless steel bolts, nuts, washers and all necessary accessories, including installation, testing and commissioning, complete as specified.(Size: 160 mm dia ,Components: Flange Adaptor, EPDM Gasket, Bolts, Nuts & Washers and Make: Cepex / Aqvastar / Pimtas (or approved equivalent)) complete in all respects as directed by the Engineer-in-Charge. |
| 332 | Supply, Installation, Testing & Commissioning of EPDM Flange Adaptor Set, complete with 110 mm dia PVC/UPVC Flange Adaptor, EPDM gasket, galvanized/stainless steel bolts, nuts, washers and all necessary accessories, including installation, testing and commissioning, complete as specified (Size: 110 mm dia,Components: Flange Adaptor, EPDM Gasket, Bolts, Nuts & Washers,Make: Cepex / Aqvastar / Pimtas (or approved equivalent)) complete in all respects as directed by the Engineer-in-Charge. |
| 333 | Supply, Installation, Testing & Commissioning of Fabricated FRP Suction & Delivery Header for pumps, 315 mm diameter and approximately 6000 mm length, complete with FRP flanged ends, supports, fastening arrangements, gaskets, bolts, nuts, alignment, testing and commissioning, as specified (Type: FRP Suction & Delivery Header,Diameter: 315 mm ,Length: Approx. 6000 mm,Ends: FRP Flanged Ends and Make: Posh / Fabricated (Approved Equivalent)) complete in all respects as directed by the Engineer-in-Charge. |
| 334 | Internal Electrification Work |
| 335 | Wiring for light / fan / exhaust fan / call bell point with 2 x1.5 sq. mm pvc insulated Copper conductor cable (FR) in pvc casing and capping complete with 6/10 amps modular type switch, cover plate, surface modular switch board including connection etc as required:- |
| 336 | Short Point :- |
| 337 | Medium Point :- |
| 338 | Long Point :- |
| 339 | Wiring for 2 way controlling light point with 3 x1.5 sq. mm pvc insulated Copperconductor cable (FR) in pvc casing and capping complete with 6/10 amps modulartype 2 way switch, cover plate, surface modular switch board including connection etc as required:- |
| 340 | Long Point :- |
| 341 | Providing and fixing of 3 pin 6/10 amps plug point with modular type 6/10 amps switch and socket including connection with 2x1.5 sq. mm PVC insulated Copper conductor cable (FR) on surface modular switch board, earthing the 3rd pin etc. as required:- |
| 342 | Providing and fixing of 3/6 pin 16/20 amps plug point with modular type 16/20 amps switch and socket including connection with 2x2.5 sq. mm PVC insulated Copper conductor cable(FR) on surface modular switch board, earthing the 3rd pin etc. as required:- |
| 343 | CIRCUITS / SUB- MAINS & CABLES |
| 344 | Wiring for circuit /Sub-main with following sizes PVC insulated copper conductor cable (FR) in PVC casing and capping etc. as required. |
| 345 | 2 X 1.5 sq mm |
| 346 | 2 X 2.5 sq mm |
| 347 | 2 X 4 sq mm |
| 348 | 4 X 10 sq mm |
| 349 | 4 X 25 sq mm |
| 350 | Wiring for Circuit/Sub-main with the following sizes of PVC insulated Copper conductor cable (FR) in existing PVC casing capping/ conduit in recess/surface including connection etc. as required:- (As per TSR 2021, sl.503) |
| 351 | 1 X 1.5 sq mm |
| 352 | 1 X 2.5 sq mm |
| 353 | 2 X 4 sq mm |
| 354 | 2 X 10 sq mm |
| 355 | Supplying and fixing of the following PVC casing capping with all accessories etc. as required. |
| 356 | 32mm x 12mm |
| 357 | 38mm x 16mm |
| 358 | Supplying and fixing of the following sizes PVC conduit (medium gauge) on surface with all accessories etc. as required |
| 359 | 25 mm dia |
| 360 | 40 mm dia |
| 361 | Supplying and fixing of the following electrical accessories including necessary connection etc. as required. |
| 362 | Electronic fancy type 5 step fan regulator with cover plate |
| 363 | Angle/batten holder |
| 364 | 32 amps DP kit kat switch:- |
| 365 | Supplying and fixing of the following modular accessories including necessary connection etc. as required. |
| 366 | Buzzer call bell (1M):- |
| 367 | Remote controlled call bell |
| 368 | Supplying and fixing of following surface/recess mounted LED luminaries in powder coated die cast housing complete with high efficiency polycarbonate diffuser and necessary connection etc. as required (with 50000 burning hours and minimum lumen output of 100 lm/watt):- |
| 369 | Surface mounted integrated 20 watt LED batten with polycarbonate diffuser:- |
| 370 | Surface mounted round/Square shaped 18/20 watt LED downlight with integral driver and high quality polycarbonate diffuser: |
| 371 | Supplying and fixing of following outdoor LED luminaries in powder coated die cast housing complete with heat resistant tempered glass/diffuser including necessary connection etc. as required (50000 burning hours and minimum lumen output of 100 lm/watt):-45 watt LED street light fixture with integral driver and secondary lens (IP 66): |
| 372 | Supplying and fixing of following LED Tubes, retrofit bulbs/lamps for LED luminaries including necessary connection etc. as required:-12 watt LED retrofit lamp with polycarbonate body and aluminium heatsink : |
| 373 | Supplying & fixing of G.I. pipe (medium gauge) bracket fabricated at suitable angle for fixing of outdoor light on wall/ RCC base with necessary MS clamp, nut, bolt etc as required:- Make: Astral, Bhagyalaxmi, Precision, Nihir, Polycab, Mihir |
| 374 | 25 mm dia |
| 375 | 40 mm dia |
| 376 | Supplying & fixing of 1200 mm sweep white color AC ceiling fan capacitor type double ball bearing complete with 300 mm down rod,canopies,shackles, 3nos blades, including wiring the down rod with 2x1.5 sqmm PVC insulated Copper conductor cable(FR) (ISI marked, BEE 1 star/minimum service value 4.0 m3/min/W) : - |
| 377 | Supplying & fixing of 1400 mm sweep white color AC ceiling fan capacitor typedouble ball bearing complete with 300 mm down rod,canopies,shackles, 3nos blades,including wiring the down rod with 2x1.5 sqmm PVC insulated Copper conductor cable(FR) (ISI marked) : - |
| 378 | Supplying and fixing of 20 mm dia extra down rod (GI Pipe Medium Guage) with necessary hole for installation of ceiling fan as required. |
| 379 | Supplying & installation of 600 mm sweep AC wall mounting air circulator including connection etc as required:- |
| 380 | Supplying of 400 mm sweep AC wall mounting fan with metal blade etc as required:- |
| 381 | Supplying & installation of 300 mm sweep 900 rpm metalic body exhaust fan including connection etc as required (ISI marked) :- |
| 382 | Supplying & installation of 450 mm sweep 1400 rpm metalic body exhaust fan including connection etc as required (ISI marked) :- |
| 383 | Supplying & installation of shutter for 380/450 mm sweep metalic body exhaust fan in the existing hole as required:- |
| 384 | Supplying and fixing of MS frame made of (25mm x 25mm x 5mm) MS angle with necessary support by (40mm x 6mm) MS flat and 12 mm thick marine plywood on top, grouted on wall with 4 nos legs (25mmx25mmx5mm MS angle 20 cm long) finished with red oxide and 2 coat synthetic enamel paint including necessary cc work, mending the damages & painting etc as required:- |
| 385 | Supplying and installation of Bus bar chamber of the following ratings and sizes made of steel sheet enclosure with all accessories including necessary connection etc. as required:- |
| 386 | 63 amps 415 volts four strip Copper busbar chamber 6 ways of size(455mmx330mmx120mm):- |
| 387 | 100 amps 415 volts four strip Copper busbar chamber 6 ways of size (610mmx410mmx120mm):- |
| 388 | 200 amps 415 volts four strip Copper busbar chamber 6 ways of size (610mmx410mmx150mm):- |
| 389 | Supplying and installation of powder coated steel sheet enclosure (MCB DB) suitable for 240/415 volts MCB/Isolator/RCCB (SP/SPN/DP/TP/TPN/FP) complete with necessary bus bar, neutral link, din rail, earth bar etc i/c connection as required. |
| 390 | 4 way SPN MCB DB (single door):- |
| 391 | (2+10) way SPN MCB DB (Double door):- |
| 392 | 6 way horizontal TPN MCB DB (Double door):- |
| 393 | 8 way horizontal TPN MCB DB (Double door):- |
| 394 | Supplying and installation of powder coated steel sheet enclosure for 415 volts MCCB (TP/FP) complete with necessary connection etc as required:-Enclosure suitable for MCCB above 100 amps upto 250 amps:- |
| 395 | Supplying & installation of 10 KA breaking capacity, B/C curve MCB of following ratings in the existing MCB DB including connection as required:- |
| 396 | 6 to 32 amps SP MCB:- |
| 397 | 40 amps DP MCB:- |
| 398 | 40/50/63 amps FP MCB:- |
| 399 | MCB Module RYB indicator light:- |
| 400 | the existing MCB DB including connection etc as required:- |
| 401 | 16 to 40 amps DP RCCB:- |
| 402 | 63 amps FP RCCB:- |
| 403 | Supplying & installation of TP/FP MCCB of following ratings in the existing MCCB enclosure/ panel board including connection etc as required (Ics=100% of Icu with adjustable settings):- |
| 404 | 16 to 100 amps FP MCCB, Breaking capacity 16/18KA (Thermal Magnetic):- |
| 405 | 160 amps FP MCCB, Breaking capacity 25KA (Thermal Magnetic) :- |
| 406 | Supplying and installation of Switch disconnector fuse unit (main switch) of the following ratings with all accessories including necessary connection etc. as required:- |
| 407 | 100 amps TPN 415 volts front handle cubical main switch (HRC):- |
| 408 | 63 amps TPN 415 volts front handle cubical main switch (HRC):- |
| 409 | 32 amps 240 volts DP main switch (rewireable):- |
| 410 | Supplying & installation of following switchgear accessories including connection etc as required:- |
| 411 | Copper Spreader links/terminals (Set of 8) for 16A-125A FP MCCB:- |
| 412 | Copper Spreader links/terminals (Set of 8) for 160A-250A FP MCCB:- |
| 413 | Copper Spreader links/terminals (Set of 8) for 500A-630A FP MCCB:- |
| 414 | conductor armoured cable with necessary connection etc as required. |
| 415 | 4 core 35 Sq mm |
| 416 | 4 core 95 Sq mm |
| 417 | 4 core 240 Sq mm |
| 418 | Supplying and fixing of aluminium terminal ends (LUGS) - long barrel of following sizes : - |
| 419 | 35 sq mm |
| 420 | 95 sq mm |
| 421 | 240 sq mm |
| 422 | Supplying and fixing of Copper terminal ends (LUGS) - long barrel of following sizes: - |
| 423 | 2.5 Sqmm |
| 424 | 4 sq mm |
| 425 | Supplying and fixing of heat shrinkable cable end termination kits of following sizes : |
| 426 | 3.5 core or 4 core 70/95/120/150 sqmm size:-each 1606.00 |
| 427 | 3.5 core or 4 core 240/300 sqmm size:- |
| 428 | Excavation of earth for cable trench of 800mm depth & 300mm width in all kinds of soil including back filling of cable trench with the excavated soil with 20cm layer of sand, 3.5 nos bricks per metre for protection including ramming, consolidating to the original shape as per dirrection of Site Engineer :- |
| 429 | Supplying, installation, testing and commissioning of following ratings inverter with Square/ sine wave technology, noiseless operation, inbuilt advance PCB programming, microprocessorwith all accessories including necessary connections etc. as required:-1500VA, 24V DC, 1 Ph input/1 Ph output inverter(Sine wave technology):- |
| 430 | Supplying, installation, testing and commissioning of following ratings Valve regulated lead acid(VRLA) battery with all accessories including necessary connections etc. as required:-12 V/ 180AH tall tubular/ flat plate Battery:- |
| 431 | Supply and fixing of 25mm x 3mm Copper on walls/ floor of the building for horizontal/ vertical network including necessary spacers and porcelain insulators at regular intervals. |
| 432 | Supply and fixing of the following sizes GI prong with necessary nuts & bolts etc as required grouted on roof for Lightning protection.Copper. Prong 1000 mm long |
| 433 | Providing earthing system with maintenance free earthing electrode of 50 mm dia &3 mtr long of dual electrode technology filled with highly conductive compound andback fill compound of 2 nos. 25 kg bag, terminal size 32mmx 6mm includingaccessories with masonry enclosure of CI cover plate size 12\\"x 12\\" having lockingarrangement including CC works etc as required:- |
| 434 | Earthing with Copper earth plate 600 mm x 600 mm x 3 mm thick i/c accessories and providing masonry enclosure with CI cover plate Size 12\\"x 12\\" having locking arrangement, along with 20 mm dia (medium gauge) watering pipe including CC work etc as required:- |
| 435 | Extra for using salt (12 kg) and charcoal (96kg) for plate earth electrode as required. |
| 436 | Supplying and drawing 4 sq. mm Copper conductor wire along with other wire for loop earthing including connection etc. as required. |
| 437 | Proving and fixing / Drawing 4.06 mm dia (8 SWG) Copper wire on surface or inexisting G.I / PVC / Polythene pipe for loop earthing as required. (As per TSR 2021,sl.707)/mtr 137.00 |
| 438 | SUBSTATION SAFETY EQUIPMENTS Providing and fixing printed instruction chart both in Eng English and Gujarati and duly framed with front glasses, for treatment of person suffering from Electric shock with minimum 50\\" diagonally size. All complete as per specification and direction of the Engineer - in - charge |
| 439 | SUBSTATION SAFETY EQUIPMENTS Supplying stand first AID box with antiseptic cream, medicine for use on wounds due burn, crepe bandage, gauge bandage, medicated ready to use bandage (Band-aid) adhesive tape for medicinal user, Scissors, anti-septic solution (Savion or similar) etc. (All above contents shall be of standard makes) All complete as per CPWD specification and direction of the Engineer - in - charge |
| 440 | SUBSTATION SAFETY EQUIPMENTS Supplying & erecting carbon dioxide (CO2) fire extinguisher user of following capacity with necessary clamps made from 50 x 6 mm M.S. Flat with nut & bolts grouted in wall complete. For 4.5 Kg Capacity All complete as per CPWD specification and direction of the Engineer - in - charge |
| 441 | SUBSTATION SAFETY EQUIPMENTS Supplying rubber matting of 12 mm thickness as per IS 5424 and of required length and breadth with good insulation property for 22 KV All complete as per specification and direction of the Engineer - in - charge |
| 442 | SUBSTATION SAFETY EQUIPMENTS Supply of 2 x 20 W FI. TA. self contained emergency light with dry type maintenance free battery. All complete as per specification and direction of the Engineer - in - charge |
| 443 | LIASON CHARGES Approval Charges for obtaining approval from S.E.B/Authority and Electrical Inspector. SEB Liason charges to obtain LT services, 1X125 KVA DG. The job involves submission of application, test report & other relevant documents as may be required to SUB/statutory authority/Electrical inspector, follow up, collection of FQ, making necessary application payment (All statutory fees will be paid by Client), coordnation with EB project team & getting the relevent workdone from EB at site for obtaining power supply, Arrange visit of Electrical Inspector, Getting necessary approvals from Electrical Inspector.Scopecovers: 1) Preparation of documents, drawings. Documents. pertaining to SEB approval shall be provided by client/consulta2) Necessary hardcopy submission is in scope of contractor.3) Follow-up with SEB approval authority officials, electrical inspector purt of job4) All statutory fees shall be paid by Client. 5) Document submission and handing over approved documents to client.All complete as per specification and direction of the Engineer - in - charge |
| 444 | Supplying, installation, testing and commissioning of of 500W LED Flood Light. (Make: Havells/ Philips/ Penasonic/ Bajaj or Approved eqaivalent Brand) All complete as per specification and direction of the Engineer - in - charge |
| 445 | Supplying, installation, testing and commissioning of 500w flood light, For Outdoor, Pure White (Make: Havells/ Philips/ Penasonic/ Bajaj or a Approved eqaivalent brand ) All complete as per CPWD specification and direction of the Engineer - in - charge |
| 446 | Wiring for 1000 watt & 500 watt flood-light, fittings using 2x2.5 sq. mm PVC insulated Copper conductor cable(FR), inclouding supply & fixing of terminal junction Box casing and capping/ conduit (Long Point) complete with nut bolts, testing and commissioning complete etc as required:-All complete as per specification and direction of the Engineer - in - charge |
| 447 | Supplying, installation, testing and commissioning of Terminal Junction Box With 12 Terminal - Up To 10 Sqmm -All complete as per specification and direction of the Engineer - in - charge |
| 448 | Supplying, installation, testing and commissioning of 2-Tier Metal UPS Stand/Trolley for Two Batteries and Inverter for Home and Office I Load Capacity 150 kg I Double Battery Metal Inverter Trolley/Stand (Goldy) with 2 Inch Wheels. All complete as per specification and direction of the Engineer - in - charge |
| 449 | Supplying, installation, testing and commissioning of MAIN DISTRIBUTION BOARD - (INDOOR) All complete as per specification and direction of the Engineer - in - charge |
| 450 | Supplying,installation and testing commisioning FOS LED High Bay Light 200W - 20000 LUMENS (Cool White 6500k, IP65 Waterproof)High brightness 25000 lumens output Energy efficient 200W LED Narrow beam uniform illumination IP65 IK08 industrial protection (Make: Havells/ Philips/ Penasonic/ Bajaj or Approved equivalent eqaivalent) All complete as per specification and direction of the Engineer - in - charge |
| 451 | Supplying of: Outdoor type 500 KVA, 11/0.433-0.250, \\"ΟΝΑΝ\\" type transformer. Standard (a) system voltage 12 KV, (b) Rated voltage (HV) 11 kv. (c) Rated voltage (LV))0.433-0.250, (d) Phase-3 phase, (e) Frequency 50HZ subjected to fluctuation of +-5% (f) Rated short circuit level- 13.1KV Fw 3 sec at 11 Kv. (g) Vector group- Dyn-11. The transformer materials shall confirming in all respect to the relevant Indian/ International standard specification with all latest amendments thereof. All complete as per specification and direction of the Engineer - in - charge |
| 452 | 11 kv, 200 amps, single brake G.O.S(one set of 3 units) |
| 453 | 12 kv, D.O. fuse unit with fuse carrier system (one set of 3 units) |
| 454 | 11 kv lightning arrester. |
| 455 | 11 kv, 45 KM Disc isolator (ball & socket type) |
| 456 | Fittings for 11 kv, 45 kn Dise isolator (ball & socket type) |
| 457 | 11 kv pin isolator |
| 458 | G.I. pin for 11 kv pin isolator |
| 459 | 75x40x6mm M.S. channel |
| 460 | 65x65x6mm M.S. angle |
| 461 | M.S. clamp for fixing of cross arm made of 50x6mm M.S. flat |
| 462 | 11mtrs. Long S.T. pole |
| 463 | Stay set complete with straining screw, stay isolater, stay road, stay plate etc. |
| 464 | Nuts and bolts 16 mm dia, 90 mm long |
| 465 | 1.1kv, 240sq mm pvc isolater and pvc sheathed aluminium conductor cable |
| 466 | 1.1kv. 70 sqmm pvc isolated and pvc sheathed aluminium conductor cable |
| 467 | G.I standard wire 7/2.5mm Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 28, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 24 daysOct 28, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 24 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender