Tender For Augmentation Of Mobile Yard Utility Services At Nsry (Pbr) Under Ge(P) North Sri Vijaya Puram.
Tender Value
75.60 Lakhs
Estimated cost
Bid Submission
27 Oct 2026
23 days left
EMD
1.38 Lakhs
Bank guarantee accepted
Document Fee
1000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
South Andamans → Andaman And Nicobar Islands
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Augmentation Of Mobile Yard Utility Services At Nsry (Pbr) Under Ge(P) North Sri Vijaya Puram.
BOQ
| Sl. No. | Item Description |
| 1 | M&L for RCC (design mix) M-30 (using 20mm graded stone aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed. |
| 2 | M&L for formwork for rough finish to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed. |
| 3 | M&L for mild steel TMT bars as in reinforcement, 10mm dia and over cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed. |
| 4 | M&L for mild steel TMT bars 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming complete and all as specified and directed. |
| 5 | M&L for drilling 12mm dia x 200mm deep in various structrural elements such as columns, beams and slabs etc. to insert the steel bars for sunshed and fixing with epoxy acrylate based anchoring adhesive complete all as specified and directed.Make :- Sika Anchor Fix + 2 Tropical or equivalent of approved make. |
| 6 | M&L for 15mm thick plastering on fair faces of brick wall in CM (1:4) surface finished even and fair complete all as specified and directed. |
| 7 | M&L for preparing newly plastered surfaces of wall and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489: 2004, alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10sqm over new surfaces as per manufacturer instruction complete all as specified and directed. |
| 8 | M&L for two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or grith complete all as specified and directed. |
| 9 | S&F 0.56mm thick plain aluminium sheeting alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing complete all as specified and directed. |
| 10 | S&F rolled mild steel section for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W(Gde-E-250) quality-A complete all as specified and as directed.Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete. |
| 11 | S&F mild steel work as in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS-1161-1979 grade St-240 with and including one shop coat of zinc chrominium primer paint complete all as specified and as directed.Note : The rates quoted deemed included for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete. |
| 12 | S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa, AZ-150 as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed. |
| 13 | S&F PVC (SWR) pipes single socketed in any length with rubber ring joints and fixed to wall of following size complete all as specified and as directed :- |
| 14 | 110 mm bore |
| 15 | S&F PVC (SWR) bends any radius with and including rubber ring joints and laid in trenched or cutting in brick wall and making good to match with existing surface of following size complete all as specified and as directed :- |
| 16 | 110 mm bore |
| 17 | M&L for mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes,without any attachment Fe-410-W Gde-E-250 quality-A complete all as specified and directed. |
| 18 | M&L for power point wiring with 1100 volts grade single core conforming to (IS:694 /1990) PVC insulated unsheathed 4.0 Sqmm multi stranded copper conductor cable (FRLSH) with continious earth wire of 4.0 Sqmm stranded copper conductor cable (FRLSH) PVC insulated unsheathed, drawn in and including surface rigid PVC conduit (Color coding of wires shall be phase, neutral and earth wire all as specified) sunk metal flush box with and including decorative polycarbonate frame for housing modular switches, sockets, fan regulators etc including white cover plate complete all as specified and directed for following:- |
| 19 | One 5 pin socket out let 5/6 Amp on independent board. |
| 20 | S&F switch socket combination 2 in 1, 5 pin, 5 and 15 Amp flush type confirming to IS : 3854 and ISI marked complete all as specified and directed. Make : Anchor, Cat Part No- 14615 / 95615 or equivalent of makes as specified. |
| 21 | S&F ceiling rose surface bakelite 65 x 50mm dia three terminals (ISI Marked) complete all as specified and directed. Make – Anchor Jumbo Code-39050 / 3224 or equivalent of make as specified. |
| 22 | S&F sub main wiring alongwith earth wire (green colour) with single core FRLS PVC insulated, unsheathed stranded copper conductor cable of voltage rating upto and including 1100 Volts drawn with and including PVC conduit (medium grade) with standard accessories, of the following sizes of cable & dia of conduit complete all as specified and directed:-NOTE :- (i) Two/four run of single core FRLS PVC cable with one/two run of earth conductor and conduit shall be measured as one unit. |
| 23 | 2x1.5 Sqmm + 1x1.5 Sqmm earth wire with PVC conduit 20mm dia |
| 24 | S&F including laying, commisioning and testing of 1.1 KV grade XLPE insulated, PVC sheathed, steel armoured, aluminum stranded conductor LT UG cable (Conforming to IS:7098), ISI marked, in trenches / ducts / through GI pipes under roads of following size complete all as specified and directed:-Note:- 1. The earth work, GI pipe shall be measured and paid sepretely.2. Cable may fixing/ passing through pipe laid in trenches or fixed to pole/ wall or fixed to LT panel etc. |
| 25 | 50 Sqmm, 3½ core. |
| 26 | 16 Sqmm, 4 core. |
| 27 | 16 Sqmm, 2 core. |
| 28 | S&F including laying in trenches or in cable ducts or clamping on wall DWC HDPE pipe of following size along with connected accessories like couplers, bends, end caps etc for LT cable protection complete all as specified and directed :- |
| 29 | Size 63mm (OD) x 50mm (ID) |
| 30 | Size 40mm (OD) x 32mm (ID) |
| 31 | M&L for earthing complete with galvanised steel earth plate electrode 600x600x6mm thick burried directly in ground, earth pit not less than 2.25 mtr depth below ground level at any type of strata with top edge of the earth plate not less than 1.5mtr below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15cm all around the plate, connected by 4 mm GI wire as earth lead by means of brass nuts and bolt, thimbles check nuts, washers including concrete chamber of PCC (1:3:6) type C-1 using 20mm graded stone aggregate with fair finish, internal surface of concrete chamber shall be given internal dia 300mm x300mm, 15mm thick plaster in CM (1:4) funnel with wire mesh, RCC pit cover of 320 x 320 x 80mm size PCC (1:2:4) Type B1 using 20mm graded stone aggregate rainforced with XPM all as shown in electrical plate No 3 of MES SSR Part-1(2009) and specified including and provision of GI wire upto 7.5 mtrs long with 15 mm dia light grade GI pipe protection and watering pipe of GI 20 mm bore, medium grade, including all exavation and earth work and connecting the earthing wire to panel, including testing on completion complete all as specified and directed. |
| 32 | Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick reinforced with XPM weighing not less than 4kg/sqm in lieu of CI cover.(ii) Cost of additional GI wire more than 7.5 mtrs will be measured and paid seperately under relevant items. |
| 33 | M&L for earthing complete with galvanised steel earth plate electrode 600mm X 600mm X 6mm thick buried directly in ground vertically earth pit not less than 2.25 meter deep below normal ground level (with top edge of earth plate not less than 1.5 meter below ground level) connected to GI earth strip of size 32x6 mm as earthing lead by means of bolts, nuts and washers all as shown in electrical plate No 3 of MES Scedule part I (2009) with conected to eath test point including adequate quantity of charcoal dust and comman salt, PCC (1:3:6) type C-1 chamber and for earth pit with 40x40x6mm mild steel angle iron frame for cover. precast RCC cover 40mm thick (1:2:4) type B1 using 20 mm graded stone aggregate reinforced with 8 mm dia round bars both ways with MS handle 8 mm dia. PGI funnel and wire mesh 20 mm dia GI pipe medium grade for watering and 40mm dia medium grade GI pipe as earth lead protection pipe complete all as specified and directed.Note:- (i) RCC pit cover shall be precast of RCC(1:2:4) type B1, 80mm thick reinforced with XPM weighing not less than 4kg/sqm in lieu of CI cover.(ii) GI earth strip and protection pipe upto and including 7.5m is deemed included in unit rate quoted by contractor. |
| 34 | S&F earth continuity conductor or main earthing lead 32x 6 mm GI strip laid in pipe / fixed to poles or any other indicated situation including jointing using by GI nuts, bolts and washer in addition to welding complete all as specified and directed . |
| 35 | S&F connecting & testing distribution board of sheet metal enclosures single door, 240V, for using MCBs / MCB isolators with having tinted copper bus bars suitable for 200 Amps rating having following capacity complete all as specified and directed:- |
| 36 | DB SPN, 2 way |
| 37 | S&F connecting & testing distribution board of sheet metal enclosures double door, IP-43, 240V, for using MCBs / MCB isolators with having tinted copper bus bars suitable for 200 Amps rating having following capacity complete all as specified and directed:- |
| 38 | DB SPN, 12 way Make :-Legrand Cat Part No- 5076 12 or equivalent others make as specified. |
| 39 | S&F MCCB 50 Hz, 415 V, adjustable type, having thermal magnetic release of following capacity complete all as specified and directed :- |
| 40 | 63Amp, 3 Pole, Icu= 25 KA,Make : Legrand, Cat Part No. 4200 43 or equivalent make as specified. |
| 41 | 40Amp, 3 Pole, Icu= 25 KA,Make : Legrand, Cat Part No. 4200 42 or equivalent make as specified. |
| 42 | S&F connecting & testing MCB, 230V/ 415V with rupturing capacity 10 KA of following capacity complete all as specified and directed:- |
| 43 | MCB 6 to 32 Amp, SP, 'C' series/ curve, Make :- Legrand, Cat Part No 4085 87 to 4085 95 or equivalent others make as specified. |
| 44 | MCB 40 to 63 Amp, SPN, 'C' series/ curve,Make :- Legrand, Cat Part No 4086 18 to 4086 20 or equivalent others make as specified. |
| 45 | Supplying, fixing, connecting and testing Mediumbay/ Highbay LED 100w luminaire, energy saving, environment friendly & robust with high efficacy (100 lm/W) with toughened glass with IP66 protection complete all as specified & directed. Make :- Havells, Cat part No PARABELLOHBP100WLED857PBOTG or equivalent others make as specified. |
| 46 | Supply, installation, commissioning and testing of outdoor type, cubical LT panel board, CPRI approved factory made, powder coated (Siemens grey structural RAL 7032 shade) having minimum thickness 100 micron, suitable for 3 phase 4 wire 415 v, 50 Hz and provided with suitable 'U' type gasket to make it dust/vermin proof & general construction confirming to IS : 8623/93, floor block mounting type made out of 3.15 mm thick CRCA sheet with using 50mm x 50mm x 6mm angle iron frame, factory fabricated duly compartmentalized for each control gear with front & back openable, lockable/ operable by keys from both sides having brass chromium plated 19mm dia fancy locks, louvers & air vent gasket for natural flow of air and to accommodate incommer/ outgoing MCCBs and TPN aluminium bus bar of rating not less than the 1.5 times the rated capacity of the incommer MCCB. The TPN bus bar shall be insulated with colour coded heat shrinkable sleeve and shall be mounted on suitable size 'F' class insulator made of non hygroscopic, non combustile, track resistant, high strength FRP/SMC/DMC material at an interval not less than 500mm through out the length of the TPN bus bar and extension links shall not be less than 300mm long supported on same type insulators and having provision for termination of incomer and outgoing cables. All inter connections between the main bus bar as well as outgoing feeders shall be carried out with TPN aluminium bus bar of rating not less than 1.5 times rated capacity of individual outgoing feeders & should be insulated with heat shrinkable PVC sleeves. All control wires shall be with FRLS PVC insulated, unsheathed 2.5 sqmm multistranded copper conductor and shall be properly bunched, tied, ferrulated for proper identification and crimped with aequate size of lugs. The cubicle shall have a bottom channel of size 75x40mm duly coated with zinc metal coating having thickness not less than 100 microns. A detachable predrilled gland plate of thickness 2 mm powder coated should be used at the bottom with and including necessary earth work and PCC work for fixing panel legs. The degree of protection for inner shell shall be IP-42 & carry the following items :- |
| 47 | (i) INCOMING :-(a) Digital multifunction meter -Qty- 01 No. (b) LED Indicator 22.5mm for 12 volts AC/DC supply -Qty- 01 set of 3 Nos. (c) MCCB, 200Amps, 4 pole, breaking capacity Icu = 36 KA, 415 Volts, AC supply, with adjustable load setting, having thermal magnetic release -Qty- 01 No (ii) OUT GOING :-(a) MCCB, 63 Amps, 4 pole, breaking capacity Icu = 25 KA, 415 Volts, AC supply, with adjustable load setting, having thermal magnetic release -Qty- 02 No (b) MCCB, 40 Amps, 4 pole, breaking capacity Icu = 25 KA, 415 Volts, AC supply, with adjustable load setting, having thermal magnetic release -Qty- 02 No (c) MCB, 63 Amps, double pole, breaking capacity Icu = 10 KA, 230 Volts, 'C' curve/ series -Qty- 03 No |
| 48 | Notes :-1. Panel manufacturers should have in house powder coating plant with minimum 8 tank pretreatment of MS sheet facilities, dust free spray paint booth. (8 tanks pretreatment process includes: degreasing/ water rinsing/ de-rusting/water rinsing/activation/phosphating water rinsing/passivation).2. Thickness of powder coating shall not be less than 80 microns and test certificate for powder coating shall be furnished along with LT panel.3. The panel manufacturer should have following certification:(i) CPRI certification degree of protection IP-54 ( should have IEC:61439-1-2 & IEC:60529 tests).(ii) CPRI certification short circuit with stand strength should be 50 KA RMS for 1 sec with initial peak of 105 KA(iii) CPRI certification rated current for short circuit not less than 5000A.4. All the electricals switch gear like MCCBs, MCB should be of same make.5. Drawing of panel board should be got approved from GE/AGE (I) before fabrication.6. Panel board should be fully compartmentalized in accordance to form 4 b of IEC 61439-1-2. |
| 49 | S&F air termination rod single pointed, aluminium rod 12mm dia and 300mm long as specified in SSR Part-I (2009) complete all as specified and as directed |
| 50 | S&F test point terminal box made of gun metal or phosphorous bronze of size 75 x 75 x 25 mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as specified and as directed. |
| 51 | S&F aluminium strip 25 x 3.15mm with saddles and fixing screws etc. for roof conductors and down conductors above ground complete all as specified and as directed. |
| 52 | S&F galvanised steel water tubing (GI pipe), medium grade with all fittings (ISI Marked) and fixed to wall, floor and ceiling or laid in trenches of following bore complete all as specified and as directed :-Note :- 80mm and 100mm bore pipe will be jointed by welding as directed at site |
| 53 | 40mm bore Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 27, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 23 daysNov 03, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 30 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender