Tender For annual maintenance contract Of Sub-Division Office Building Along With C Us Of Teesta Canal Sub-Division No Vi At Panjipara, Block Goalpokher I & P.S. Goalpokher, Dist-Uttar Dinajpur
Tender Value
7.15 Lakhs
Estimated cost
Bid Submission
07 Oct 2026
5 days left
EMD
14311
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dinajpur Uttar → West Bengal
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for annual maintenance contract Of Sub-Division Office Building Along With C Us Of Teesta Canal Sub-Division No Vi At Panjipara, Block Goalpokher I & P.S. Goalpokher, Dist-Uttar Dinajpur
BOQ
| Sl. No. | Item Description |
| 1 | Cutting and clearing jungles including shrubs, water weeds, bushes, trees, plants, upto 30 cm. girth including removing as directed by Engineer-in-charge. |
| 2 | Brick work with 1st class bricks in cement mortar (1:4) |
| 3 | 125 mm. thick brick work with 1st class bricks in cement mortar (1:4) in ground floor. |
| 4 | Ordinary Cement Concrete (mix 1:2:4) with graded stone chips (20 mm nominal size) excluding shuttering and reinforcement, if any, in ground floor as per relevant IS codes.(ii) River bazree |
| 5 | Stripping off worn out plaster and raking out joints of walls, celings etc. upto any height and in any floor including removing rubbish within a lead of 75m as directed. |
| 6 | Plaster (to wall, floor, ceiling etc.) with sand and cement mortar including rounding off or chamfering corners as directed and raking out joints including throating, nosing and drip course, scaffolding/staging where necessary (Ground floor).[Excluding cost of chipping over concrete surface](ii) With 1:4 cement mortar(c) 15 mm thick plaster |
| 7 | Neat cement punning about 1.5mm thick in wall, dado, window sill, floor etc. NOTE: Cement 0.152 cu.m per100 sq.m |
| 8 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary(a) On timber or plastered surfaceWith other than hi-gloss of approved quality-(iv) Two coats (with any shade except white) |
| 9 | Priming one coat on steel or other metal surface with synthetic oil bound primer of approved quality including smoothening surfaces by sand papering etc |
| 10 | Painting with best quality synthetic enamel paint of approved make and brand including smoothening surface by sand papering etc. including using of approved putty etc. on the surface, if necessary (b) On steel or other metal surfaceWith other than hi-gloss of approved quality(iv) Two coats (with any shade except white) |
| 11 | Applying Exterior grade Acrylic primer of approved quality and brand on plastered or cencrete surface old or new surface to receive decorative textured (matt finish) or smooth finish acrylic exterior emulsion paint including scraping and preparing the surface throughly, complete as per manufacturer's specification and as per direction of the EIC.In Ground Floor(b) Two Coats |
| 12 | Protective and Decorative Acrylic exterior emulsion paint of approved quality, as per manufacturer's specification and as per direction of Engineer-in-Charge to be applied over acrylic primer as required. The rate includes cost of material, labour, scaffolding and all incidental charges but excluding the cost of primer.In Ground floor (Two Coat)a) Normal Acrylic Emulsion |
| 13 | Supplying & laying 3mm thick pre-fabricated plastomericwater proofing membrane conforming to EN 12311-1 &ASTMD 5147, manufactured with atactic poly propylene (APP) modified premium grade asphalt , specially reinforcedwith non-woven polyester core with polyester reinforcement @160 gms per sqm & both faces covered with thermo-fusiblepolyethylene film /MineraL on top face over a coat of primer @ 0.40 lit/sqm of manufacturer's specification onsmooth,clean dry surface prepared wherever required.Lapjoint shall be provided of 75 mm in longitudinal & 100 mm intransverse direction and fused using LPG/ Propane torch employing extra care ensuring full bondage, completeremoval of entrapped air and sealing edges into grooves inappropriate manner as per direction of Engineer -in-charge all complete including materials,labour and applicabletaxes. (Payment shall be made on the basis of finished surface area.).Membrane Property: Softening Point > 150 deg C, Cold Flexibility < -6 deg C, Tensile Strength, N/cm : 600 (longitudinal), 450 (transverse), Tearing Strength, N: 300 (longitudinal), 200 (transverse) |
| 14 | Supplying, fitting and fixing bib cock or stop cock.(f) (i) Polythene Bib Cock / Stop Cock (HD) with metal inlet (EMCO /ATLAS or equivalent)15 mm. |
| 15 | Supplying, fitting and fixing UPVC pipes A - type and fittings conforming to IS 13592-1992 with all necessary clamps nails including making holes in walls, etc. and cutting trenches in any soil, through masonry concrete structure etc. if necessary and mending good damages including jointing with jointing materials ( Spun yarn, valamoid / bitumen / M. seal etc.) complete.B) UPVC Fittings: a) Plain Tee(ii)110 mm. Dia. |
| 16 | c) Bend 87.5 degree(ii)110 mm. Dia. |
| 17 | Supplying, fitting and fixing PVC pipes of approved make of Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I). with all necessary accessories, specials viz. socket, bend, tee, union, cross, elbo, nipple, longscrew, reducing socket, reducing tee, short piece etc. fitted with holder bats clamps, including cutting pipes, making threads, fitting, fixing etc. complete in all respect including cost of all necessary fittings as required, jointing materials and two coats of painting with approved paint in any positionabove ground. (Payment will be made on the centre line measurements of total pipe line including all specials. No separate payment will be made for accesories, specials. Payment for painting will be made seperately)(a) For Exposed WorkPVC pipes 25 mm |
| 18 | 40 mm |
| 19 | 50 mm |
| 20 | Supplying, fitting and fixing gunmetal wheel valve of approved brand and make tested to 21 kg per sq. cm. (for water lines only). 50 MM |
| 21 | 40 mm |
| 22 | 25 mm |
| 23 | Supply of PVC pipes & fittings Schedule 80 (medium duty) conforming to ASTMD - 1785 and threaded to match with GI Pipes as per IS : 1239 (Part - I).(B) Socket (Dia) 25 mm |
| 24 | 40 mm |
| 25 | 50 mm |
| 26 | Elbow (dia) |
| 27 | .40 mm |
| 28 | 50 mm |
| 29 | (E) Tee (dia) |
| 30 | 40 mm |
| 31 | 50 mm |
| 32 | (I) Union (dia) |
| 33 | 40 mm |
| 34 | 50 mm |
| 35 | (O) Solvent Cement 250gm |
| 36 | Supply of Mazdoor (Male Female) |
| 37 | Supply of Mathor Mazdoor / Tarmar. |
| 38 | Supply of Ordinary Carpenter |
| 39 | Supply of Helper for Carpenter |
| 40 | Supply of Plumber |
| 41 | Supply of Helper for Plumber |
| 42 | Cleaning and disinfecting upto 2000 litre Water Tank including masonry reservoir. |
| 43 | Cleaning urinal with channel with acid |
| 44 | Cleaning E.P. or Anglo-Indian W.C. with acid. |
| 45 | Cleaning I.P.W.C. with acid. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 07, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 5 daysOct 07, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 5 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender