Tender For Repair To Floor, Sanitary Fittings, Internal Water Supply, Plinth Protection, Wall & Other Allied Works In Labs, Mt, Admin Bldg, Other Area, Technical Area And Adjoining Area Of 13 Brd And 16 Brd At Af Stn Palam Under Ge (Af) Gurgaon No 1.
Tender Value
35 Lakhs
Estimated cost
Bid Submission
22 Oct 2026
19 days left
EMD
70000
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Gurgaon → Haryana
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Repair To Floor, Sanitary Fittings, Internal Water Supply, Plinth Protection, Wall & Other Allied Works In Labs, Mt, Admin Bldg, Other Area, Technical Area And Adjoining Area Of 13 Brd And 16 Brd At Af Stn Palam Under Ge (Af) Gurgaon No 1.
BOQ
| Sl. No. | Item Description |
| 1 | Schedule-A |
| 2 | Dismantling floor, stone, hearth or wall tiling including cement mortar bedding but not backing, removing rubbish off the premises complete all as specified and directed by Engr-in-charge. |
| 3 | Demolition of Cement Concrete (un-reinforced) of any description, not exc. 150mm thickness (above or below Ground Level) and removing the same from Site(s), complete all as specified and as directed. |
| 4 | M&L for 25 mm thick PCC 1:2:4, Type B-0 (12.5mm Graded Stone Aggregate) as in sub floor etc., including rough top surface to receive floor finish complete all as specified and as directed. |
| 5 | M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed or bedding layer of cement mortar 1:6 complete including all as specified and directed by Engr-in-charge. |
| 6 | M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (Square/ rectangular ) in floors area of each tile exc 0.11 sqm but n.exc. 0.18 sqm set and jointed in neat cement slurry and pointed in white or colour cement to match, over and including 15 mm thick screed plaster in CM 1:6 complete all as specified and directed by Engr-in-charge. |
| 7 | M&L for Non skid ceramic coloured tiles 7 to 8 mm thick (squares/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed in CM (1:6) complete all as specified and directed |
| 8 | M&L for glazed ceramic colour tiles of of 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm set and jointed in neat cement slurry and pointed in coloured cement on vertical surfaces such as in dado/skirting etc over and including 10 mm thick backing coat in CM 1:4, complete all as specified and directed by Engr-in-charge. |
| 9 | M&L for 10 mm thick Vitrified light shade Coloured tiles, square/ rectangular double polished, area of each tile n.exc. 0.36 sqm, in floor including 15 mm thick screed bed in CM 1:6 etc.,set and jointed in neat cement slurry and pointed in white with pigment to match for laying floor finishes all as specified and as directed by Engr-in-Charge. |
| 10 | M&L for 10 mm thick vitrified light shade coloured tiles (square/ rectangular) double polished, area of each tile not exc 0.36 sqm set and jointed in neat cement slurry and pointed in coloured cement on vertical surface such as Skirting/ dado etc over and including 10mm thick backing coat in CM 1:4, complete all as specified and as directed by Engr-in-charge. |
| 11 | S&F for 10 mm thick Vitrified light shade Coloured tiles, square/ rectangular double polished, area of each tile exc. 0.42 sqm but not exc 1.00 sqm, in floor including 15 mm thick screed bed in CM 1:6 etc.,set and jointed in neat cement slurry and pointed in white or coloured cement with pigment to match for laying floor finishes all as specified and as directed by Engr-in-Charge. |
| 12 | M&L for self embosed grooves, bull nose finished, anti skid, full body homogeneous vitrified tiles for steps (Tread) of stairs of size 300x 1200x 13 to 16 mm or 300x 1000x 13 to 16 mm or 250x 1000x 13 to 16 mm set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed in CM 1:6 complete all as specified and directed. |
| 13 | M&L for anti skid, full body homogeneous vitrified Tiles for Risers of Stairs of size 150x1000x 13 to 16 mm/ 200x 1000x 13 to 16 mm or 200x1000x 13 to 16 mm/ 200x 1200x 13, jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade over and including 10mm thick rendering in CM 1:4 on stone/brick/ concrete surfaces complete all as directed |
| 14 | Providing and laying heavy duty non-skid coloured digital printed parking tiles of size 400mmx400mm X 8-10mm thick set and jointed in neat cement slurry and pointed with white cement with pigment to match the tile colour over and including 15mm thick screed bedding in CM 1:6, complete in all respect as specified and directed. |
| 15 | Demolition of Stone slabs and tiles of any description or thickness in floor or wall, aprons and laid badded and pointed in any mortar, complete all as specified and directed by Engr-in-Charge. |
| 16 | M&L for Pre Polished Machine cut Green/ black Marble stone 18 - 20mm thick slab in flooring/ Cills over 15mm thick screed in CM 1:4, laid and jointed with grey cement slurry mixed with pigment to the shade of the slab including rubbing and polishing complete all as specified and as directed. |
| 17 | M&L for 18-20 mm thick machine cut kota stone slab flooring of size not less than 500 x 500 mm over 20 mm thick cement mortar (CM) 1:6 screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete in all respect as specified and directed. |
| 18 | M&L for 18-20 mm thick machine cut kota stone slab of size not less than 500 x 500 mm in riser of steps, skirting, dado and pillar over 15 mm thick rendering in cement mortar (CM) 1:4, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing, complete in all respect as specified and directed. |
| 19 | Cutting and grinding mirror polishing old kota stone/ green marble flooring including applyign cement slurry to fill the existing joints, complete all as specified and directed by Engr-in-Charge. |
| 20 | M&L Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite over 15 mm thick screed bed in CM 1:4 including grinding, moulding rounnding and polishing bedding as in, window Cill, kichen shelf plateform etc complete all as specified and directed by Engr-in-Charge. |
| 21 | M & L for rounding edges of stone slabs one edge, such as steps,cooking platforms and other similar situations, complete all as specified and as directed. |
| 22 | M&L for 75 mm thick PCC 1:3:6 Type C2 (using 40 mm graded stone aggregate) as in plinth protection and courtyard, finished even and smooth/fair with out using extra cement complete all as specified |
| 23 | M & L for 100 mm thick cement concrete 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in floor & surfaces finished even and fair using extra cement, complete all as specified. |
| 24 | M & L for 100 mm thick PCC (1:4:8) type D-2 (using 40 mm graded stone agg) as sub base surface finished even & fair with using extra cement complete all as specified and directed. |
| 25 | M&L in repair for 25mm thick Chequered Cement Concrete Tiles 30 cm x 30 Cm pre printed coloured, Set and Jointed in Neat Cement Slurry with Grey Cement and Pigment over and including 15mm thick Screed Bed in CM (1:4) as in Path, complete all as specified and as directed. |
| 26 | M&L 60 mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footparth, parks, lawns, drive ways or light traffic parking etc.,of required strength, thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over and including 40mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand, complete all as specified and directed by Engr-in-Charge. |
| 27 | M&L for PCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in coping, benching, levelling course, bed block for flooring, rungs, window cills etc complete all as specified and directed by Engr-in-charge |
| 28 | Taking down Cement Plaster from wall and ceiling of any description from Brick/concrete surfaces including raking out Joints, hacking for Key, scrubbing down with Water, etc., and removing same from the Site(s), complete all as specified and as directed. (Note :- Rate included for four storey building including scaffolding and all safety measures) |
| 29 | M&L for 15mm thick rendering in CM 1:4 on fair faces of brick or concrete surfaces including finishing even and smooth without extra cement all as specified and as directed by Engineer in Charge. |
| 30 | M&L for 15mm thick rendering on brick or concrete surfaces in internal surfaces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge. |
| 31 | M&L for 5mm thick rendering in CM 1:3 on concrete/gunniting surface as in ceiling finished even and smooth w/o using extra complete all as specified and directed by Engr-in-charge |
| 32 | M&L for Washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand mixed with Liquid WPC) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 white cement: 1/2 coarse sand: 2 stone chipping 6mm t0 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified (Payment for providing grooves shall be made separately) |
| 33 | M&L for forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using Aluminium Channel, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as specified and directed by Engineer-in-charge. |
| 34 | M&L for applying two coat of exterior Acrylic emulsion paint (100% acrylic) of approved colour and shade over a coat of primer and over 1 to 2 mm thick birla putty punning including preparation of new plastered surface complete all as specified and as directed by Engineer-in-charge. (Whether coat long life) including necessary scaffolding upto 4th floor. |
| 35 | M&L for applying two coat of Distemper oil emulsion by Auto Roller over a coat of primer over 1 to 2 mm thick birla putty punning including finishing by Sanding Machine and Auto Roller new surface complete all as specified or as directed by Engineer-in-charge. |
| 36 | M&L for preparation of newely plastered ceiling surface and applying three coats of white wash complete and all as specified and as directed |
| 37 | M&L for preparing old plastered surface of walls and applying two coats distemper oil emulsion over a coat of primer complete all as specified |
| 38 | Demolition of brick work or stone/boulders masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etac but excluding ashlars facings, dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge. |
| 39 | M&L for brick work with sub class 'B' bricks straight or curved on plan exceeding 6m mena radius built in cement mortar 1:4 complete all as specified and directed by Engr-in-charge. |
| 40 | S&F 500 Litre capacity three layered rotational moulded polyethylene water storage tank (Cylindrical vertical with closed tap) hoisted and fixed in position including 20 mm dia GI pipe medium grade washout pipe of 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe of 600 mm long with all fittings including dismantling/ taking down of the existing tank, complete all as specified and directed by Engr-in-charge. |
| 41 | S&F 1000 Litre capacity three layered rotational moulded polyethylene water storage tank (Cylindrical vertical with closed tap) hoisted and fixed in position including 20 mm dia GI pipe medium grade washout pipe of 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe of 600 mm long with all fittings including dismantling/ taking down of the existing tank, complete all as specified and directed by Engr-in-charge. |
| 42 | S&F in repairs ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed 20 mm bore complete, all as specified and directed by Engineer in charge. |
| 43 | S&F in repairs, 20 mm Bore gun metal Gate/Globe half turn valves with iron wheel/Lever fixed-in-repairs complete all as specified and directed by Engineer in charge. |
| 44 | S&F, jointing and testing galvanized steel water tubing 15 mm bore (dia) (ISI Marked), medium grade with all fittings such as bends, elbow, socket, reducer etc and fixed to concealed or on wall, ceiling or laid in floors or any other situation including taking up or down existing steel tubing/ PPR pipe of any grade and connection includings making good the disturbed surfaces, complete all as specified and directed by Engr-in-charge. |
| 45 | S&F, jointing and testing galvanized steel water tubing 20 mm bore (dia) (ISI Marked), medium grade with all fittings such as bends, elbow, socket, reducer etc and fixed to concealed or on wall, ceiling or laid in floors or any other situation including taking up or down existing steel tubing/ CPVC pipe of any grade and connection includings making good the disturbed surfaces, complete all as specified and directed by Engr-in-charge. |
| 46 | S&F, jointing and testing galvanized steel water tubing 25 mm bore (dia) (ISI Marked), medium grade with all fittings such as bends, elbow, socket, reducer etc and fixed to concealed or on wall, ceiling or laid in floors or any other situation including taking up or down existing steel tubing/ CPVC pipe of any grade and connection includings making good the disturbed surfaces, complete all as specified and directed by Engr-in-charge. |
| 47 | S&F for 20mm dia CPVC SDR 11 pipe fixed to concealed/wall, ceilling,laid in floor etc incl all fittings with solvant anf brass threaded fittings for fixing taps etc including Taking down unserviceable 15mm Steel Water Tubing with Fittings and Connections, including wtar tighteness test etc., complete all as specified and as directed. |
| 48 | S&F for 25mm dia CPVC SDR 11 pipe fixed to concealed/wall, ceilling, laid in floor etc incl all fittings with solvant and brass threaded fittings for fixing taps etc including Taking down unserviceable Steel Water Tubing with Fittings and Connections, etc., including water tightness test complete all as specified and as directed. |
| 49 | S&F in repair Angle Stop Valves 15mm Bore (dia) cast copper alloy, screw down, high pressure, with crutch or butterfly handle, screwed down, screwed for Iron Pipe or for Brass Ferrule complete all as specified and as directed |
| 50 | S&F in repair Brass CP fancy type Bib taps 15mm Bore (dia) Chromium plated Long Body, screwed down, screwed for Iron pipe or for Brass Ferrule; complete all as specified and as directed. |
| 51 | S&F in repair Fancy type Two Way Bib Tap 15mm bore, chromium plated, screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and Fly Nuts, screwed for Iron pipe and fixed in repairs, complete all as specified and as directed. |
| 52 | S&F Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.00 to 1.50 metre long flexible tube and ABS wall hook including making connections and fixed in position, complete as all specified and directed. |
| 53 | S&F in repairs wall mixer 3-in-1 system with provision for both hand shower and overhead shower complete with 115 mm long bend pipe, connection legs & wall flange, all as directed and specified. |
| 54 | S & F in repairs Hand shower (health faucet) with 8 mm dia, 1 m long flexible tube and wall hook with back flow preventer in repairs all as specified and as directed |
| 55 | S & F in repairs over head shower rose 200 mm X 200 mm square shape Sigle flow ( Body and Face Plate Stainless Steel with chrome finish ) with rubbit cleaning system complete all as specified and as directed. |
| 56 | S & F in repairs Chromium Plated shower arm Square shape 600 mm Long complete all as specified and as directed. |
| 57 | S & F in repairs Hand shower 140 mm dia round shape Single flow with air effects with rubit cleaning system complete all as specified and as directed. |
| 58 | S & F in repairs Hand shower flexible tubes 12 mm dia & 1.5 meter long with nuts complete all as specified and as directed. |
| 59 | S & F in repairs Premium wall bracket for hand shower 35 mm dia and 100 mm long round shape complete all as specified and as directed. |
| 60 | S&F in repairs Single Lever Basin mixer without pop up waste system & 450 mm long braided hoses complete all as specified and as directed. |
| 61 | S&F in repairs Sink Cock with Regular Swinging Spout ( Wall Mounted Model) with wall flange 15 mm dia chroumium plated fancy type complete all as specified and as directed. |
| 62 | S & F in repiars soap dish complete all as specified and as directed. |
| 63 | S & F in repairs soap dispenser with mettalic bottle complete all as specified and as directed. |
| 64 | S & F in repairs towel rack 600 mm long with lower hangers as in bathrooms complete all as specified and as directed. |
| 65 | S & F in repairs Single Towel Rail 600 mm long complete all as specified and as directed. |
| 66 | S & F in repairs CP toilet paper roll holder with flap complete all as specified and as directed. |
| 67 | S & F in repairs towel ring square/rectangular with round flange complete all as specified and as directed. |
| 68 | S & F in repairs shower basket small complete all as specified and as directed. |
| 69 | S & F in repairs Corner shower basket complete all as specified and as directed. |
| 70 | S&F in repairs Floor Mounted Coupled Water Closet of size 380x660x 765 mm with flushing cistern, with UV Soft Close Seat Cover , Hinges, Fixing Accessories Set including S Trap complete all as specified and as directed. |
| 71 | S&F in repairs table Top basin of size 485x395x150 mm including waste coupling and waste pipe complete all as specified and as directed. |
| 72 | S & F in repair double coat hook complete all as specified and as directed. |
| 73 | S&F in repair 15 mm dia bore CP Bib cock, cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipes or for union and fixed complete all as specified and directed by Engr-in-charge. |
| 74 | S&F in repair 15 mm dia bore CP two in one bib cock, cast copper alloy, screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipes or for union and fixed complete all as specified and directed by Engr-in-charge. |
| 75 | S&F in repair of Wall mixture of telephonic 15mm bore dia cast copper alloy with chromium plated screwed down high pressure with or without lettered \\"Hot\\" or \\"Cold\\" with long screwed shanks and fly buts screwed for iron pipe complete all as specified and directed by Engr-in-charge. |
| 76 | S&F in repair basin mixer of 15mm dia cast copper alloy fancy type chromium plated crutch and butter fly handle screwed down complete all as specified and directed by Engr-in-Charge. |
| 77 | S&F in repair sink mixer of 15mm dia telephonic type mixer cast copper alloy fancy type chromium plated crutch and butter fly handle screwed down complete all as specified and directed by Engr-in-Charge. |
| 78 | S&F in repair, 15 mm dia bore swan neck pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or “cold’ with long screwed shank and fly nuts, screwed for iron pipe and fixed complete all as specified and directed by Engr-in-charge. |
| 79 | S&F in repair 120 mm to 150 mm dia square size fancy type shower rose brass chromium plated with CP arms of 30 to 60 cm long for 15mm bore GI pipe complete all as specified and directed by Engr-in-charge. |
| 80 | S&F in repair of 15mm dia telephonic hand shower of long 200 mm to 300 mm cast copper alloy fancy type screwed down complete all as specified and directed by Engr-in-Charge. |
| 81 | S&F in repairs 15 mm dia bore dia angle stop valves, fancy type chromium plated, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pope or for unions and fixed, complete all as specified and directed by Engr-in-charge. |
| 82 | S&F concealed stop valve CP 15mm bore, cast copper alloy, screwed down, high pressure with long shank or butterfly handle screwed both ends for iron pipe or union and fixed in repairs complete all as specified and as directed |
| 83 | S&F in repair Health Faucet with 1.00 mtr long SS tube and stand/ hook, complete all as specified and directed by Engr-in-charge. |
| 84 | S&F in repair vitreous china wash down water closet pan (pedestal pattern)or white (excluding flushing cistern and flush pipe) including connection to drain or outgoing pipe and flush pipe anti syphonage pipe etc and making good the disturbed surfaces of floor complete all as specified and directed by Engr-in-charge. |
| 85 | S&F PVC Flushing Cistern 10 LITRE capacity, Low Level Valve Less, Symphonic Action type, White, with Inlet, Ball Valve, Float and Handle including a Pair of Cast Iron Brackets duly Painted/Erecting Stand and PVC connection pipe 15mm size, PVC Flush Pipe of polythene 32mm dia for Low Level Flushing Cistern including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and fixed including Taking down/out Unserviceable Flushing Cistern and connected Items, complete all as specified and as directed. |
| 86 | S&F in repair water closet seat cover white colour closed pattern with flat bottom covered and mild steel chromium plated hinging device complete all as specified and directed by Engr-in-charge. |
| 87 | S&F in repair of floor /wall mounted western toilet/commode S/P trap square type seat in built in single pices white water closet (EWC) including complete all fittings cmplete all as spd and directed by Engr-in-Charge. |
| 88 | S&F in repairs Vitreous China Squatting Pan ‘ORISSA’ Pattern, size 580X440 mm White, with ‘P’ or ‘S’ Trap, Integral Foot Rest, providing Joints between Flush Pipe and Socket of WC Pan excluding Flushing Cistern and Flush Pipe), fixing with and including provision of 150mm thick Lime Concrete Bedding including Taking down/ out unserviceable WC Pan and connected Items, complete all as specified and as directed. |
| 89 | S&F in repair for high pressure PVC connection pipe 15mm dia with Brass CP Check nut and rubber washer complete with 600 mm length complete all as specified and as directed by Engr-in-Charge. |
| 90 | S&F for Gratings 125mm dia with/ without waste hole, fixed in repairs complete all as specified and as directed. |
| 91 | S&F Vitreous China Wash Hand Basin 630X450mm in size, White (Flat Back Type) with 32mm dia Brass Chromium Plated Waste Fitting,UPVC Bottle trap, UPVC’ 32mm bore Waste Pipe, a Pair of Cast Iron Brackets duly Painted/ Erecting Stand including Cutting and Pinning in Ends, Making Good Disturbed Surfaces in Cement Mortar 1:3 and fixed including Taking down Unserviceable Wash Hand Basin and connected Items, complete all as specified and as directed. |
| 92 | S&F in repair vitreous china urinals flat back large type, complete including providng and fixing waste coupling 32/40 mm, plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement, fixing automatic flushign cistern with brackets, flush pipe, grating and union for discharge pipe, complete all as specified and directed by Engr-in-charge. |
| 93 | S&F in repair Urinal spreader of brass male thread with chrome finish for fixing with 15 mm dia pipe, complete all as specified and directed by Engr-in-charge. |
| 94 | S&F in repair HDHMR board luxury bathroom vanity washbasin cabinet with mirror floor/ wall mounted, mouveable or fixed with drayers as per site requirement with 32 mm dia brass chromium plated waste fitting including granite stone thickness 18-20 mm of desired colour and fancy type CP WHB mixer and all fittings as required at site for smooth functioning, making good disturbed surfaces in cement mortar 1:3 and fixed, complete all as specified and directed by Engr-in-Charge. |
| 95 | S&F in repairs Looking Mirror selected quality of size 900 mm x 600 mm x 6 mm thick, having four holes on corners fixed to walls with CP Brass screws with fancy type head top complete all as specified and directed by Engr-in-Charge. |
| 96 | S&F in repair 6 to 8 mm thick electrical looking mirror of rectangular/ square/ oval/ circular shape of size exc 0.27 sqm but not exc 0.45 sqm with three light mode as required including all fittings and make good of all surface, complete all as specified and directed by Engr-in-Charge. |
| 97 | S&F in repair toilet paper holder of size 13 cm x 13 cm x 7 cm chromium plated of glossy finish fixed to wall with chromium plated brass screw complete all as specified and directed by Engr-in-charge. |
| 98 | S&F Vitreous China Soap Dish, Single, as Approved, fixing with Brass Chromium Plated Screws including Taking down unserviceable Soap Dish of any description, complete as all specified and directed. |
| 99 | S&F Brass CP Towel Rail 600mm Long, as Approved, fixed including Taking down unservice-able Towel Rail of any description, complete as all specified and directed. |
| 100 | S&F in repairs PVC Cabinet 350x550x100mm with Mirror of selected quality glass mounted on wall and fixed to wooden plugs with CP brass stud 25 mm, complete all as specified and directed by Engr-in-Charge. |
| 101 | S&F in repairs corner glass shelf of 300 mm long fixed on the wall with nuts & washers, complete all as specified and directed by Engr-in-charge. |
| 102 | S&F in repairs glass shelf 450 mm long on wall with screws and making good surface of wall, complete all as specified and directed by Engr-in-charge. |
| 103 | S&F in repairs ABS 350 ml wall mounted liquid soap dispenser with all fittings, complete all as specifed and directed by Engr-in-charge. |
| 104 | Dismantling of old existing PVC/CI/concrete pipes of any description, jointed in cement mortar up to 100 mm dia, complete all as specified and directed by Engr-in-Charge. |
| 105 | S&F PVC (SWR) Pipes 75mm in Bore (dia), Single Socketed, in any length with Rubber Ring Joints fixed to Walls or Laid in Floors, etc, complete all as specified and as directed. |
| 106 | S&F PVC (SWR) Bend suitable for PVC (SWR) Pipes 75mm in Bore (dia) with access door, jointing with Solvent Cement and fixed-in-repairs, complete all as specified and as directed. |
| 107 | S&F 75 mm dia PVC (SWR) Tee with access door suitable for PVC (SWR) Pipes 75mm in Bore (dia), jointing with Solvent Cement and fixed-in-repairs, complete all as specified and as directed. |
| 108 | S&F 75mm dia sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints fixed to walls, complete all as specified and directed by Engr-in-charge. |
| 109 | S&F in repair 75mm dia CI bends with oval access door, diminishing pieces or tapers, complete all as specified and directed by Engr-in-Charge. |
| 110 | S&F in repair 75mm dia CI branch pieces, single (equal or unequal) ordinary or inverted (Spigot or socket type) or with paralled branches with ovel access door, complete all as specified and directed by Engr-in-Charge. |
| 111 | S&F 100mm dia sand cast iron soil, waste and vent pipes in any length with or without ears with cement joints fixed to walls with oval access door, complete all as specified and directed by Engr-in-Charge. |
| 112 | S&F in repair 100mm dia CI bends, diminishing pieces or tapers, complete all as specified and directed by Engr-in-Charge. |
| 113 | S&F in repair 100mm dia CI branch pieces, single (equal or unequal) ordinary or inverted (Spigot or socket type) or with paralled branches with ovel access door |
| 114 | M&L for replacement of 75mm outlet CI floor/nahani trap with steel grating including jointing and breaking/ dismantling any type of floor and making good cement concrete to the B-1 (1:2:4) and testing after repairs and taking down existing trap etc complete all as specified and directed by Engr-in-Charge |
| 115 | S&F in repair stack clamp made out of GI angle and 10mm dia U bolt and nut with washer for 75/ 100 mm dia pipe, complete all as specified and directed by Engr-in-Charge. |
| 116 | S&F Stainless Steel Kitchen Sink with Drainage Board of Overall Size 915X460mm and Bowl Size 410X330X160mm, made of Stainless Steel 1.0mm thick Sheet with Plugs, Chromium Plated Waste Coupling and Washer including Bedding in Cement Mortar 1:4 to Dwarf Wall or fixing Cantilever Brackets and Connection to Pipe including Taking down unserviceable Sink and Connected Items complete all as specified and as directed by Engr-in-Charge. |
| 117 | S&F in repair, 4 mm thick sheet glass for window/ ventilators ordinary quality and glazing with rubber beading/oil putty in square exc 0.50 Sqm in each pane, complete all as specified and as directed by Engr-in-Charge. |
| 118 | S&F in repair, 4 mm thick figured glass for window/ ventilators ordinary quality and glazing with rubber beading/oil putty in square exc 0.50 Sqm in each pane, complete all as specified and as directed by Engr-in-Charge. |
| 119 | S&F in repair, 6-8 mm thick tinted glass fixed with rubber beadig and bushes, complete all as specified and directed by Engr-in-Charge. |
| 120 | S&Fin repair stainless Steel Wire Cloth, 0.36mm nominal dia of Wire and average width of aperture 1.4 mm and fixed with Tinned Tacks of Mild Steel Wire Stapes, complete all as specified and as directed. |
| 121 | M&L for Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall where the apron is not provided using chemical emulsion at the rate of 7.5 litres per sq.m of the vertical surface of the sub-structure to a depth of 300mm including excavating channel along the wall and rodding etc. complete. |
| 122 | M&L for along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron. |
| 123 | Taking down chowkat or frame with shutter (without taking out shutter from the frame) not exc 1.50 Sqm each as doors, windows & ventilators etc. and removal from site, complete all as specified and directed by Engr-in-charge. |
| 124 | All as per Srl Item No. 101 above Ditto but exceeding 1.50 sqm each and n.exc. 4 Sqm each |
| 125 | Taking down shutters only exc 1 Sqm and n.exc. 2 Sqm each |
| 126 | S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube in opening as per specification & drawing mentioned in SSR, complete all as specified and directed by Engr-in-charge. |
| 127 | S&F for 30 mm thick factory made solid panel PVC door shutter confirming to criteria of testing as per IS : 4020, consisting of frame made out of MS tube of 19 gauge thickness & size 19x19mm for stiles and 15x15mm for top & bottom rails MS frames shall have a coat of red oxide primer of approved make and shall be covered with 5mm thick heat moulded PVC `C' channel of size 30x50mm forming styles and 5mm thick 75mm wide PVC sheets for top rail lock rail and bottom rail on either side and 10mm (5mmx2) thick 20mm wide cross PVC sheet as gap insert for top rail and bottom rail paneling of 5 mm thick PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rail with 30 mm wide x 5 mm thick PVC sheet beading on either side and joined together with solvent cement, adhesive and an additional 5 mm thick PVC strip of 20 mm width is to be struck on the interior side of 'C' channel using PVC solvent adhesive complete as per manufacturers specifications & drawings and complete all as specified and directed by Engr-in-charge. |
| 128 | S&F Mild Steel Butt Hinges 100 mm, Medium Weight, Cold Rolled ISI Marked and fixed, complete all as specified and as directed. |
| 129 | S&F 200 mm long aluminium anodized barrel tower bolt of extruded section complete. |
| 130 | S&F 150 mm long Aluminium anodised handles, cast type, complete in all respect as speicfied and directed by Engr-in-Charge. |
| 131 | S&F SS sliding door bolt, length 250 mm including a minimum of 6 bolts, nuts and washers all as specified |
| 132 | S&F in repair Floor door stopper of SS with hard drawn steel spring. Fixed in floor overall length of cover plate 150 mm complete |
| 133 | M&L for demolition of sunken filling concrete, removal of loose concrete and cleaning the surface and after proper cleaning filling the cracks with polymer modified mortar using Dr fixit pidicrete URP and providing 50mmx50mm angle fillets on the vertical upstands, parapet wall junction corners, service units and properly dressed by preparing polymer modified mortar with DR Fixit pidicrete URP in the ratio of 1:3 by adding polymer 10% by weight of the cement, add the water little little unit the required consistency is achieved and thereafter providing and applying two coats of acrylic polymer modified cementitious coating Dr Fixit pidifin 2K of M/s Pidilite Industrieshaving elongation at break 50% 5 bar resistance to positive water pressure, Adhesive strength ASTM D 7234-1 N/mm sq, water vapour transmission as per ASTM E96 of 030 perms and crack bridging ability as per EN 1062-7 upto 1 mm. Apply two coats of Dr Fixit pidifin 2K slurry “ coverage of 0.55-0.58 Sqm/kg of mix slurry. Provide and lay 45 gsm glass fibre mesh over the angle fillet when the first coat is still wet. Allow the first coat to dry for 6-8 hours, then apply the second coat at a direction perpendicular to first coat. Allow the coating to air cure for 5 days before conducting water ponding test for 24 hrs etc or other equivalent product as approved by GE in sunken area complete all as per the manfactures instruction, including removing rubbish material from building and thrown in low lying empty area at any distance out side MD land complete all as specified and as directed by Engineer-in-Charge |
| 134 | M&L rendering 10 mm thick in cement plaster (1:3) using coarse sand finished even and smooth without using extra cement with steel trowel on sunken surfaces using integral water proofing compound.( WPC shall be measured and paid separately) |
| 135 | S&F aluminium colour powder coated door Frame and shutter single or double leaf glazed/pre laminated particle board interior panels fabricated including aluminium powder coated beading rubber Gasket and packing materials and shall be drilling in existing wall and thrust bolt suitable size complete comprising the following:- (a) Door frame section 101.60x44.45x1.93 mm fixed as per spd (b) Door Shutter Vertical Style of Size 85x44.45x2 mm as per spd. (c) Door Shutter Top style section 95.25x44.45x2.00 mm as per spd. (d) Aluminium coloured powder coated middle lock rail/bottom rail section 150x44.45x1.93mm cat No.20002. (e) Aluminium coloured powder coated Tower Bolt 02 Nos in each shutter 200 mm long as spd. (f) Aluminium coloured powder coated handle 02 Nos in each shutter 150 mm long as per spd. (g) Door Floor spring ISI Marked (h) Six lever mortice lock brass on in each door.(j) 12 mm thick partical board (pre laminated both face) exterior grade ISI Marked (k) Tinted glass/Plain glass(Colour) 5mm thick. |
| 136 | S&F aluminium coloured power coated (shade or tint as directed by GE) Side Hung window/ventilator frame and Shutter with section as per TD-109/2012 sheet (1/4 to 4/4) comprising the following:- (a) Al coloured powder coated window frame section 101.60x44.45x1.93 mm fixed as per spd(b) Aluminium coloured power coated double shutter (Glass and Wire Mesh shutter) 44x44x1.50mm top/bottom/sides style. (c) Aluminium coloured power coated butt hinges 8 Nos in each window 100 mm sizes as per spd. (d) Aluminium coloured power coated tower bolt 3 Nos in each window 150 mm long as per spd.(e) Aluminium coloured power coated handle 2 Nos in each window 100 mm long as per spd.(f) Tinted/coloured glass 5 mm thick fixed to window with rubber gasket & Al Powder coated beading. (g) Aluminium coloured power coated grill make deco grill DG-104 fixed with \\"H\\" Section. Note : If ground requirement for sliding window/AC window contractor should provide as per direction of Engineer-in-Charge without any price adjustment. |
| 137 | S&F in repairs aluminium powder coated Ventilator with Top Hung shutters /fixed type with section of 16 guage including necessary jointing cleats, glazing clips, rubbers gasket, anodised aluminium snap beading, screw, powder coated aluminium anodised fittings complete all as specified and directed by Engineer-in-Charge. |
| 138 | S&F in repair 12mm thick Toughned glass with or without logo as required in doors, partitions automatic doors and similar work including cutting to shape, drilling holes required, with 02 Nos fancy handle of size 300 mm long, locking arrangement, floor springs and complete fixing arrangements as in doors/ partitions complete all as specified and directed by Engr-in-Charge (Note:- Rate of etched logo is inclusive of rate quoted by the contractor). |
| 139 | S&F for factory made single extruded WPC ( Wood polymer composite) solid door /window/ceosetory windows& other Frames/Chowkhat of size 65x100 mm compraising of virgin PVC polymer of K value 58-60 ( Suspension grade),calcium carbonate and natural fibers (wood powder/rice husk/wheat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum,screw withdrawal strength of 2200 N(face) & 1100 N ( Edge),minimum compressive strength of 58 N/mm2,modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof,water/moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fastners of required dia and length complete as per direction of Eng In charge .( MS holdfast / lugs dash fastners shall be included in unit rate of item). Note:- For WPC solid door/window frames,minus 5 mm toletance in dimension i.e. depth and width of profile shall be acceptable .Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 140 | S&F for factory made single extruded WPC ( Wood polymer composite) solid decorative type flush door shutter of size 35 mm thick compraising of virgin PVC polymer of K value 58-60 ( Suspension grade),calcium carbonate and natural fibers (wood powder/rice husk/wheat husk ) and non toxic additives ( maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 650 kg/cum,screw withdrawal strength of 1800 N(face) & 900 N ( Edge),minimum compressive strength of 50 N/mm2,modules of elasticity 850 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof,water/moisture proof and fire retardant and fixing with Stainless Steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws ,complete as per direction of Eng In charge . Note:- SS butt hinges and SS screws shall be included in unit rate of item. |
| 141 | Supply and fixing factory made uPVC white colour Three track three panels sliding window or Two track two panels sliding window with fly proof S.S wire mesh /Glazed (Thickness of pane , made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension, comprising of uPVC multichambered frame, with inbuilt roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners of suitable size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, complete all as specified and directed by Engineer-in-Charge. Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 142 | Supply and fixing factory made uPVC white colour fixed /openable glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 1.50 sqm.) comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners of suitable size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Glass shall be paid separately).Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 143 | S&F in repair, Hollow PVC wall lining consisting of 05 to 10 mm thick plain colour PVC sheet inclusive of solvent cement & foxing on wall surfces L & U channel including dismantling of pvc sheet as per specification and drawing, complete all as & fixing on L& U channel, specified and as directed by Engr-in-Charge. |
| 144 | S&F in repair, Solid charcoal panel/Louver panel for wall interiour consisting of 5 to 10 mm thick, decorative type inclusive of solvent cement, PVC fillet if required & fixing at site as per specification & drawing complete all as specified and as directed by Engineer- in- Charge. |
| 145 | S&F in repair, Solid PVC Wall Lining consisting of 5 mm thick Plain colour PVC sheet inclusive of solvent cement, PVC fillet & fixing at site on PVC frame as per specification & drawing complete all as specified and as directed by Engineer- in- Charge. |
| 146 | S&F in reppair stain lesssteel curtain rod of 20/ 25 mm dia fancy type including MS bracket, decorative side knob, corner bracket etc complete all as specified and directed. |
| 147 | S&F vanishing roller/ vertical blinds as required for windows/ door/ ventilator of any colour and pattern with exc 1.5 sqm but not exc 4.00 sqm each, as approved by Engr-in-Charge including connected items i.e. rod, hooks etc with complete fittings, complete all as specified and directed by Engr-in-charge. |
| 148 | Removal, collection, loading, transportation and disposal of debris/malwa from each and every building, shafts, common areas and all connected/approach area, including lifting from scattered locations, stacking, loading into tractor trolley, conveying and unloading at approved dumping site for all leads up to 10 km , each trolley shall be of minimum size 3.0 m × 1.5 m × 0.90 m (L × B × H) or equivalent complete cleaning of site and making good of disturbed surfaces.complete all as specified and as directed by Engr-in-charge. Note: No Lifts shall be use for transportation of materials in Buildings. Please Enable Macros to View BoQ information |
| 149 | Removal, collection, loading, transportation and disposal of debris/malwa from each and every building, shafts, common areas and all connected/approach area, including lifting from scattered locations, stacking, loading into tractor trolley, conveying and unloading at approved dumping site for all leads up to 10 km , each trolley shall be of minimum size 3.0 m × 1.5 m × 0.90 m (L × B × H) or equivalent complete cleaning of site and making good of disturbed surfaces.complete all as specified and as directed by Engr-in-charge. Note: No Lifts shall be use for transportation of materials in Buildings. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 22, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 19 daysOct 24, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 21 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender