Tender For Construction Of Two Classroom Building At Gundur Pues In Gundur Panchayat
Tender Value
34.60 Lakhs
Estimated cost
Bid Submission
16 Oct 2026
12 days left
EMD
34600
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Tiruchirappalli → Tamil Nadu
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Construction Of Two Classroom Building At Gundur Pues In Gundur Panchayat
BOQ
| Sl. No. | Item Description |
| 1 | Construction of Two Class Room Building at Gundur PUES in Gundur Panchayat. Earthwork excavation for foundation (for narrow excavation) to full Depth as per designed in all soils and sub soils except soft disintigraded rock not requiring blasting and hard rock requiring blasting and Balling water wherever neceesary. Refilling the sides of foundation with excavated with other than sand in layers of well rammed and compacted and depositing the surplus earth in places shown by the departmental officers with an initial lead of 10m and initial lift of 2m and clearing and levelling the site etc complete and complying with standard specification. |
| 2 | Supplying and Filling in foundations and basement with filling M-Sand in layers not exceeding 15cm thick well watered rammed and consolidated etc.complete complying with standard specifications. |
| 3 | Plain Cement Concrete 1:4:8 (one part of cement four parts of sand and eight parts of hard broken stone) using 40mm gauge hand broken hard broken granite stone jelly complying with standard specifications in foundations and basement. |
| 4 | Refilling the approved good quality earth in plinths, area development etc. wherever specified in layers is not exceeding 200mm thick with avilable earth at site. |
| 5 | Collection and supply of gritty gravel from appd quarry including cost and conveyance of all materials to site including all labour charges for filling etc complete. |
| 6 | Supplying and erecting Centering and Shuttering for soffits including necessary supports and strutting up to 3m height for with all cross bracings using Mild Steel sheets of size 90 X 60 cm and 10 BG stiffened with welded Mild Steel angle of size 25mm X 25mm X 3mm for boarding laid over silver oak Joists of size 10cm X 6.50 cm spaced at about 90 cm centre to centre and supported by casunna props of 10cm to 13cm dia spaced at not more than 75 cm centre to centre etc complete complying with the standard specification (Payment for centering shall be given after the concrete is laid Footing Plinth Beam etc. |
| 7 | Plain surfaces such as roof slab, beams lintels loft still slab staircase waist portico slab similar works |
| 8 | Square and rectangular columns and small quantities such as sunshades, parapet cum drops, window boxing, fin projections and other similar works. |
| 9 | Providing and laying in position, M-20 Grade in accordance with IS 456-2000, using 20mm and down grade hard broken grganite stone jelly for all RCC items of works with minimum cement content of 350 kg/m3 and maximum water cement ration of 0.50 including admixture (Plasticiser / super Plasticiser) in recommended proportions as per IS 9130 to accelerate, rated setting of concrete, improve workability without impairing strength and durability with about (5.0 cum) 7730kg of 20mm machine crushed stone jelly and with about (3.3 cum) 5156 kg of 10-12 mm machine crused stone jelly and with about (4.79 cum) 7670 kg of sand but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with Mechanical vibrators, finishing curing etc., and providing fixtures like fan clamps in the RCC Floor / roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS Standards (No Separate payment will be made by the Department for |
| 10 | Ground Floor |
| 11 | Steel - Fe 500 D: Supply, Fabrication and placing of reinforcement steel of high yield strength ribbed bars of various diameters and grade conforming to IS 1786 for reinforced concrete work. The work includes recoiling, straightening, cutting, bending, fabricating, and placing in position, at all levels including lead and lift according to drawings, specifications etc, complete and supply & use of 18G black annealed binding wire double fold to tie the bars in position and providing precast cement / PVC cover blocks for main reinforcement to ensure specified cover and complete including all labour charges etc as directed by departmental officers |
| 12 | Brick work in following Cement Mortar 1:5 using best quality II class table moulded Fly ASK Bricks 8\\"3/4 X 41/4\\"x23/4\\" for foundation and basement including curing etc.,complete complying with standard specification including scaffolding curing cost of reinforcement etc all complete as per specifications and drawings as directed by the Engineer in-charge . Foundation basement |
| 13 | Ground Floor |
| 14 | Providing and applying 3mm Wall putty,to finishing the exposed surfaces of R.C.C items of works such as Roof (or) floor slabs,beams,and sun shades etc, to correct plane and level including scaffolding, hacking of surface,chiselling the undulated surface whenever necessary and curing etc., all materials and labour complete in all respects including all lead ,lift and decent and as directed by the Enineer incharge.This rate includes the cost of providing Cement Mortor beadings for sun shades ,steps,landing slabs,elevation etc.complete complying with standard specifications |
| 15 | Providing & applying 12mm thick Cement Plaster in CM1:5 (1part of cement 5parts of sand) to walls internally in single coat at all levels to correct line and level including chicken wire mesh at all joints of bricks and concrete surfaces with minimum overlap of 150mm in all directions, scaffolding ,rounding off or chambering of corners offsets , fin/bands,projections,etc.,.and cleaning of surface ,raking out joints ,roughening of surface,chiseling the undulated surface wherever necessary and curing etc., all materials and labor complete in all respects including all lead ,lift and descent and as directed. |
| 16 | Paving the floor with best approved quality fine polished Kota stone slabs of size 600x600 of 18/20mm with machine cut edges and matching marble slab not less than 100mm width other than Adanga Marbles as border laid over a cement mortar bed of 20mm thick using cement mortar 1:3 (one cement and three M.sand )fixing the slabs in true right angles with minimum possible width of joints and pointing the joints with matching colouring pigments and polishing with floor polisher to a high degree of finish etc., The Kota stone slabs and other materials to be used shall be got approved by the Executive Engineer concerned before use on work,etc.,complete as per standard specification |
| 17 | Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4(One cement,Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl , thread lining,curing etc.,complete complying with standard specification and as directed by the departmental officers(The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers). |
| 18 | Supplying and fixing in position steel balustrades using 20mm square rods spaced at 150mm centre to centre so that the two balustrades in each step shall be placed centrally and the top of balustrades connected with the hand rails (cost of hand rail shall be measured and paid separately) by means of MS flats of size 40mmx6mm in the groove 40mmx6mm provided at the bottom of hand rail,the bottom of balustrades connecting all square rods to the entire length including cost of square rods,flat and applying one coat of red oxide primer to the iron surfaces etc., completee complying with standard specification and as directed by the departmental officers |
| 19 | Supply and fixing 40mm dia GI pipe for staircase hand rail including labour charges for cutting,weiding and fixing with MS flats (excluding cost of flat)etc., as directed by the departmental officers |
| 20 | Providing, fabricating and fixing M.S. grills Windows, and ventilator,gates, ladders, rail pipes, nosing angles, with M.S.lugs in staircase steps etc., made out of M.S rods, flats, angles, pipes, channels etc. including necessary fixtures complete as per drawings and specifications and as directed by the Engineer. |
| 21 | UPVC Window supplying and fixing UPVC ( Un-PLASTICIZED Polyvinyl chloride) windows of casement type (open) from the profile the size of outer frame 60mmx58mm and shutter profile are reinforceement with gi/1mm 125GSM and 100% corrosion free, the profiles are mlulti chamberedcv section with wall thick of 2mm.The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power points locks and also it operates as handle.The corners and joints should be welded and cleaned.Radiations free pin headed plain or brownclour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action,security protective hinges,strong locking systems and as per size for arresting noise and energy loss. The connecting mechanisim between sah and outer frame that enables opening of the window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames The window should be got approved from the Executive Engineer before use on work. |
| 22 | Manufacturing, supplying and fixing of Steel doors with following specification.MS angle of size 40x40x6mm at 3.5 kg/m used for outer frame and MS Angle of size 35x35x5mm at 2.6 Kg/m for the shutter frame. Stiffeners with 32x6mm at 1.5 Kg/m MS Flat is provided as the lock rail of the door and welded intact on both ends to the shutter frame.18 G CR Sheets of best quality is laid as panel in the shutter frames. 18x5mm at 0.70 kg/m MS flat is welded over the 32x6mm at 1.50kg/m MS Flat on the rear side of the door, sandwiching the CR Sheet for rigidity. Additional stiffeners with 18x5mm at 0.7 Kg/m MS flats are provided diagonally on the rear side of the shutter. 300mm length of hinges 2Nos, for shutter is provided. 6 Nos. of 250mm length hold fasts 200mm length specified at the ends are welded to the outer frame of the door. Tower bolt 2 Nos. at the top provided. |
| 23 | Supplying and Painting new ceiling plastered surface with two coats of distempering one coat of distemper primer |
| 24 | Supplying and painting the walls with one coat of wall primer and two coats of Exterior emulsion (apex or equivalent) as instructed by the departmental officers including preparation of surface curing, etc., complete in all floors complying with standard specifications (The colour and shade of the cement paint shall be got approved by the Executive Engineer before use of work). |
| 25 | Paving the Top of roof with solar reflective ceramic tiles of size 305x305x7mm thick of approved quality and colour laid in cement mortar 1:3 (one cement and three M.Sand )12mm thick and pointed with tile grout (Nitotile Grout or equipment)and cement in the ratio of 1:3 for joint,curing etc.,complete complying with standard specification and as directed by the departmental officers.(The make and brand of the tiles should be got approved by the Executive Engineer before use on works) |
| 26 | Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER) |
| 27 | Supplying and fixing cuddapah slab for cupboard shelf |
| 28 | Supplying and fixing 160mm Dia PVC Rain water down fall pipes of following dia meter etc., complete. |
| 29 | Providing Cup-board Shutter with frame using termite / water proof plywood of 19mm thick over which laminated sheet of 0.8mm thick fixed inside the shutter and 1mm thick fixed in the outside of the shutter using fevicol along with necessary furniture fittings, such as, hydralic hinges, tower bolt, handles, multi purpose locks etc., as directed by the Departmental Officers. The design pattern, water proof plywood, laminate sheet and other materials should be gotapproved from the Executive Engineer befoe use on wor |
| 30 | Magnetic Green fibre Board including GST |
| 31 | BaLa painting including GST |
| 32 | Provision for Soil Test charges |
| 33 | Quality control |
| 34 | Display Notice board |
| 35 | Drinking Water Pedestal with PVC Tank including GST |
| 36 | Provision for Nameboard charges |
| 37 | GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column \\"BB\\" for all works in this package} Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 16, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 12 daysOct 16, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 12 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender