Tender For Provn Of 01 X Guard Room (Approx Area 40 Sqm) For Canal Guard And Certain Other Sanctioned Work At Faridkot Mil Stn
Tender Value
14.14 Lakhs
Estimated cost
Bid Submission
21 Oct 2026
18 days left
EMD
28280
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Faridkot → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Provn Of 01 X Guard Room (Approx Area 40 Sqm) For Canal Guard And Certain Other Sanctioned Work At Faridkot Mil Stn
BOQ
| Sl. No. | Item Description |
| 1 | Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/ loose soil |
| 2 | M&L PCC 1:4:8 type D2 (using 40mm graded aggregate) in foundation, filling and mass concrete |
| 3 | M&L RCC M-30 (20mm graded aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete |
| 4 | M&L RCC M-30 (20mm graded aggregate) in Columns, pillars, piers, posts and struts |
| 5 | M&L RCC M-30 (20mm graded aggregate) in Beams, cantilevers, bressummers, lintels over 1.5m span |
| 6 | M&L for RCC M-30 in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified |
| 7 | Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter, flat, rough finished surfaces of concrete |
| 8 | Formwork to sides of pillars, posts, struts, piers, columnn and stanchions, Square, rectangular or polygonal rough finished surfaces of concrete |
| 9 | Form work to sides and soffits of floor or roof beam, beam, hauchings, girders, bressum-emers, lintels, cantilevers, shelves incl supports overhangs etc also splays between floors and beams, flat, rough finished surfaces of concrete |
| 10 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) |
| 11 | S&F MS TMT Bars of 10 mm dia and over,cut to length,bent to shape required including cranking, binding spirally for hooping for columns hooking ends and biniding with and including MS wire (annealed) not less than 0.9 mm dia or securining with clip all as specified. |
| 12 | S&F MS TMT Bars of 5 mm dia and over up to 10 mm dia in stirrups, spacers and binders,cut to length bent to shape required including cranking, binding spirally for hooping for columns hooking ends and biniding with and including MS wire annealed not less than 0.9 mm dia or securining with clip all as specified. |
| 13 | M&L for brick work with fly ash bricks (old size bricks) straight or curved on plan exceeding 6m mean radius with old size bricks in wall built in cement mortar (1:6) complete all as specified. |
| 14 | M&L Cement concrete 50mm thick type C2, 1:3:6 using 20mm graded aggregate as in plinth protection/path finishing surfaces even and fair (without using extra cement) all as specified |
| 15 | Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm |
| 16 | Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the starting point. |
| 17 | M&L 100mm thick PCC 1:4:8 type D-2 (Using 40 mm graded aggregate), as in flooring, sub base etc complete all as specified. |
| 18 | S&F Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) (coloured tiles) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors set and jointed in neat cement slurry and pointed in coloured cement to match the coloured tiles15mm thick screed bed or bedding layer CM 1:4 for laying finishes,complete all as specified as directed by Engr-in- Charge |
| 19 | M&L Rendering 10 mm thick in cement plaster 1:6 on stone masonry surfaces or surface other than fair face of brickwork or on one side of lathing, finished even and smooth without using extra cement |
| 20 | M&L Rendering 5mm thick in cement plaster 1:3 on ceiling finished even and smooth without using extra cement |
| 21 | M&L Rendering 15 mm thick in cement plaster 1:4 on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement |
| 22 | M&L preparation of newly plastered or unplastered surfaces of wall and applying two coat of distemper oil emulsion white/tinted with a wall care putty finished surface complete all as specified and directed by Engr -in - charge. |
| 23 | M&L Preparation of new ceiling surfaces plastered or unplastered and applying two coat of white wash complete all as specified and directed by Engr -in - charge. |
| 24 | M&L for preparation of new surfaces of wall and applying two coat of cement base paint complete all as specified.Note :- Curing of surface will be carried out as per Para 15.15.3 of SSR Part-I |
| 25 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size 65 x 125 mm comprising of virgin PVC polymer, calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. |
| 26 | M & L For 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides. |
| 27 | S&F 2nd class hardwood factory made glazed skeleton shutters 35 mm thick open rebated and prepared to receive guage etc but divided into squares, with plain chamfered or rounded, metered and riveted sash bars any numbers . |
| 28 | S&F Aluminium frame for doors, window with one or more rebates including joining cleat for fixing etc complete with powder coating on Aluminium minium thickness of powder coating 50 micron as per the specification the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawal plug and screw or with fixing clip or with expansion hold plate fasteners including making arrangements to fix guard bars and S&F of PVC sleeves for guard bars. Aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required all complete as per the direction of Engineer-in-charge.Note: Guard Bars shall be measured and paid for separetely. |
| 29 | M&L for providing and fixing stainless steel (Grade 304) in Window Grill made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the Grill with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size as Specified and Directed by Engr-in -Charge |
| 30 | S&F Aluminium window (glazed and gauzed both),side hung type without sash bars, aluminum section weighing 0.55 Kg/m including necessary joining cleats, glazing, clips, rubber packing, anodised aluminium snap beading screws,aluminium fitting such as peg stays 150mm long (01 nos) for each shutter, hinges type B-21 100mm long (02 Nos) suitable handle (01 No) with powder coating of any colour (thickness of powder coating not less than 50micron) etc complete all as specified and directed.Note: Only Glass and wiremesh will be measured and paid seperately. |
| 31 | M & L sheet glass ordinary quality 4 mm thick and glazing with Beading in square n exc 0.50 Sqm in each panes fixed to steel, metal or wooden window frames complete all as specified. |
| 32 | S&F Stainless steel wire cloth 0.40 mm nominal dia of wire and avarage width of aparture 1.40mm and fixed etc., complete all as specified |
| 33 | S&F 100 mm long SS butt hinges, medium weight, cold rolled, mild steel and fixed |
| 34 | S&F 150 mm long Aluminium handles cast type anodised |
| 35 | S&F 200 mm long Aluminium anodised barrel tower bolts of extruded section and fixed |
| 36 | S&F 250 mm long aluminium alloy, anodised, sliding door bolt with hasps staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolt and sliding bolts of extuded sections or cast aluminium alloy and fixed |
| 37 | S&F 140 mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor |
| 38 | S&F Making kebs with PCC (1:2:4) type B0 using WPC along side wall adjoining to roof in concave shape complete all as specified. |
| 39 | M&L for Roof Treatment as specified below and as directed :(a) Cleaning, washing of surface and removing all existing bitumen coatings/ APP membrane completely with intense wire brushing or high speed water jet. Surface should be free from any loose paint, dust or grease. (b) Rendering 10 mm thick in cement plaster 1:4 with WPC on roof, fair faces of brick work or concrete surfaces all as specified (c) All cracks upto 3mm at corner joints, channels and parapets should be treated with crack seal and bigger cracks, damaged portions and hollow areas must be repaired with polymer modified cement mortars.(d) Applying one coat of PrimeSeal/ Epoxy Primer/ShaliUrethane BTD White diluted with potable water in the ratio of 1:1 and apply @ 0.40 kg/ sqm (0.20 kg BTD+0.20 Kg water)(e) Laying polyster reinforced fiber net/50 gsm Geotextile mesh, upto 300 mm on walls.(f) Applying three coat of HydroShield PUD microfibre reinforced UV resistent polyurethane (solid content 68% ) / Damp Proof ultra UV Stable fibre reinforced elastomeric liquid waterproofing membrane formulated with PU hybrid polymers (Solid content 55%)/ SmartCare PU Magnum elastomeric waterproofing coating based on hydrophobic polyurethane (solid content 85%)/Single Component Elastomeric Liquid Membrane ShaliUrethane BTD White/coloured (Elongation 400% ± 50, Solid Contents > 80% & Specific Gravity @ 30 OC 1.5 ± 0.03) @ total 2.00 Kg per sqm in two coats for maintaining thickness of 1.5mm, with paint brush/ roller upto 300 mm on walls.(g) The complete treatment to be carried out by authorised applicator of waterproofing manufacturer.Make : DrFixit/ Asian/STPNote : (i) The treatment shall be carried out as per the manufacturers instructions, and as directed by Engineer in Charge. (ii) The plan area of floor shall be considered for payment . |
| 40 | M&L for Soil Filling under floor including well ramming with watering, spreading and levelling in layers n exc. 25 cm thick |
| 41 | M & L modular point wiring complete with ISI marked 1.5 sqmm single core PVC insulated unsheathed cable 1100V grade FRLS with multistranded copper conductor drawn through concealed in wall/ceiling with PVC rigid concealed conduit suitable size with all accessories such as bend, reducers, MS hooks,ceiling rose, galvanised steel pressed modular terminal boxes of suitable sizes for mounting of switchs, sockets, fan regulator etc covered with plastic laminated modular top cover sheet of required color fixed with brass screws and cup washers painting terminal boxes inside and outside with one coat red oxide primer including fixing and 1.5 sqmm copper conductor as earth continuity to connect common earth dolly and including taking down old unserviceable wire any type and making good disturbed surfaces of walls as necessaty completed for the following all as specified and directed.(a) One light point/Fan point/Exhaust point controlled by one way switch |
| 42 | (b) One three pin socket out let 5 amps on the same board with other switches |
| 43 | (c) One 3 pin, 5A switch socket outlet point on independent board |
| 44 | All as per item no. 41 here-in-before but with 2.5 sqmm cable for 1No 16 amps socket outlet point on independent board including 2.5 sqmm PVC insulated unsheathed cable multistranded with copper conductor green in colour as earth continuity conductor. |
| 45 | Supply and fixing Modular switch 1 way 6 amps one module incl taking down unsv switch any type all as specified and directed |
| 46 | Supply and fixing Modular socket 6A 2/3 pin combined 2 module incl taking down unsv socket any type all as specified and directed |
| 47 | Supply and fixing Modular switch 1 way 16 amps 1 module incl taking down unsv switch any type all as specified and directed |
| 48 | Supply and fixing Modular socket 6A / 16A - 2/3 pin combined 2 module incl taking down unsv socket any type all as specified and directed |
| 49 | S & F Modular fan regulater step type 120watt single module size complete all as directed |
| 50 | Supply and fixing ceiling rose 3 terminal 240 volt 5 Amprs complete all as specified and directed .. |
| 51 | Supply and fixing of LED tube light fiting 20W, (4 feet long) 230 V, surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver and including connections up with copper conductor wire with suitable size as per specification and directed. |
| 52 | Supply and fixing of LED tube light fiting 10W, (2 feet long) 230 V, surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver and including connections up with copper conductor wire with suitable size as per specification and directed. |
| 53 | Supply and fixing LED street light 25 watt luminaries comprising of epoxy powder coated housing, enclosed with glass cover including 40mm GI Bracket and fixing arrangement in road light, security light etc complete with all accessories and including connecting up with twin core twisted flexible copper conductor cable 1.5 sqmm with suitable size. all as.specified and directed |
| 54 | Supply & fixing Energy efficient Ceiling fan complete with blades, down rods, electronic type regulator & accessories, 230 V,1200mm sweep, BEE, 5 star rated with brushless direct current motor (BLDC) including writing of MES number (Black, Roman, Italic or Indian) n. exc 30cm height complete all as specified and directed . |
| 55 | Supply and fixing Exhaust fan steel body AC single Phase 230 Voltof size 300 mm Sweep with blades and frame and Louvers as diected .. |
| 56 | Supplying and fixing of water heater (Gyser) of capacity 25 ltrs, BEE appreoved 5 star rating, 230V,single Phase complete including fastners for hanging on wall and cP and PVC Connection for inlet and outlet upto stop cock complete all as specified and directed. |
| 57 | Supply and Fixing Modular Ac socket enclosure (3/4 module ) complete with Mini MCB SP 25 Amp C curve complete all as specified and directed . |
| 58 | S&F sheet metal enclosure for DB's SPN 230 volts 8 way double door complete all as specified and directed .. |
| 59 | Supply and fixing amp rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) 6 to 32 Ampr with over load and short circuit prote complete al as specified and as directed.. |
| 60 | Supply and fixing 10 KA 'B' curve miniature circuit breaker (MCB) SPN and current carrying capacity 40 AMP, in the MCB DB Complete with connection complete all as specified and directed by Engr-in-Charge. |
| 61 | M & L for earthing complete with GI earth plate elctrode 600mmX600 mm X6mm thick buried directly in ground not less than 2.25 mtrs below ground level with top edge of plate not less than 1.5 mtrs deep below normal ground level connected to galvanised earth wire 4 mm by means of nuts bolts and check nut to earth plate and to main board of DB including nessary PCC 1:2:4 type B-1 Pit cover Fraame .GI Pipe 15 mm diavLight grade for protection and GI pipe 20 mm Dia Medium Grade for watering with funnel wire mesh,salt and charcoal dust all over the plate all as specified and directed. |
| 62 | M&L for Roof trusses (framed),tubular vertical post, trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections,tubular pole) including distance pieces, cleats etc. |
| 63 | S&F Rolled Mild steel Plates (plain or Chequred) channels, square cut or notched, forming holes, with riveted, bolted or welded attachment confirming to Fe 410 - O or Fe 310 - O. |
| 64 | S&F Pre painted galvalume aluminium zinc coating GI based corrugated steel sheet (ISI Marked) 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering fixed with self tapping screw all as specified and directed. |
| 65 | M&L for Preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed by Engr-in-Charge. |
| 66 | S&F hangers 6mm dia GI (up to 1200 mm length ) adjusting level fixed to roof slabs by means of ceiling long complete all as specified and directed |
| 67 | S&F Gl frame work for seamless ceiling comprising of Gl perimeter channnel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylon sleeves and screws at 450 mm centre to centre/intermediate channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with Gl cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kurled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the ntermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre. complete all as specified and directed |
| 68 | S&F Exposed metal frame ceiling with calcium silicate board 8 mm thick of siliceous and calcareous material reinforced with cellulose fibre for fixing in 600mm x 600mm grid (Frame work for ceiling shall be measured and paid separately) |
| 69 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), terrazo dado/wall tiling and skirting. etc on brick or stone walls etc including racking out joints hacking for key and scrubbing and removing rubbish off the premises complete all as specified. |
| 70 | M&L Vitrified ceramic tiles 10mm thick (Square/rectangular) light shade polislhed area of each tiles not exceeding 0.36 Sqm in floors set and jointed with adhisive and pointed in epoxy to match the coloured tiles over 15mm thick screed bed or bedding layer CM 1:4 for laying finishes, complete all as specified as directed by Engr-in- ChargeNote :- (i) Adhisive measured and paid separatly. (ii) Cost of epoxy included in items. |
| 71 | S&F Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) (coloured tiles) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in floors set and jointed with adhisive and pointed in epoxy to match the coloured tiles over 15mm thick screed bed or bedding layer CM 1:4 for laying finishes, complete all as specified as directed by Engr-in- ChargeNote :- (i) Adhisive measured and paid separatly. (ii) Cost of epoxy included in items. |
| 72 | S&F Glazed ceramic coloured tiles with highlighter in vertical surface 450x300x7mm thick set and jointed with adhisive and pointed in epoxy to match the coloured tiles over 15mm thick screed bed or bedding layer CM 1:4 for laying finishes, complete all as specified as directed by Engr-in- ChargeNote :- (i) Adhisive measured and paid separatly. (ii) Cost of epoxy included in items. |
| 73 | M&L ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 but not exceeding 0.36 sqm, cut to reqd size and shape as in skirtings etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match |
| 74 | S&F Aluminium frame for doors, window with one or more rebates including joining cleat for fixing etc complete with powder coating on Aluminium minium thickness of powder coating 50 micron as per the specification the top and bottom horizontal members and vertical members adjacent walls shall be fixed with floor, ceiling walls and cills where required and fixing with the help of rawal plug and screw or with fixing clip or with expansion hold plate fasteners including making arrangements to fix guard bars and S&F of PVC sleeves for guard bars. Aluminium section shall be smooth, rust free, straight mitred and jointed mechanically where ever required all complete as per the direction of Engineer-in-charge. |
| 75 | S&F 100 mm long, Stainless Steel hinges with stainless steel steel screws complete. |
| 76 | S&F Aluminium anodised barrel tower bolts, 150 mm long of extruded section complete all as specified and directed. |
| 77 | S&F sheet glass of 5.5 mm, ordinary quality in area n.exc 0.5 Sqm in each pane in aluminium Section glazing incl necessary rubber beading complete all as specified. |
| 78 | S&F Stainless steel wire cloth 0.36 mm nominal dia of wire and avarage width of aparture 1.40mm and fixed etc., complete all as specified |
| 79 | S&F Aluminium window (glazed and gauzed both),side hung type without sash bars, aluminum section weighing 0.55 Kg/m including necessary joining cleats, glazing, clips, rubber packing, anodised aluminium snap beading screws,aluminium fitting such as peg stays 150mm long (01 nos) for each shutter, hinges type B-21 100mm long (02 Nos) suitable handle (01 No) with powder coating of any colour (thickness of powder coating not less than 50micron) etc complete all as specified and directed.Note: Only Glass and wiremesh will be measured and paid seperately. Please Enable Macros to View BoQ information |
| 80 | S&F Aluminium window (glazed and gauzed both),side hung type without sash bars, aluminum section weighing 0.55 Kg/m including necessary joining cleats, glazing, clips, rubber packing, anodised aluminium snap beading screws,aluminium fitting such as peg stays 150mm long (01 nos) for each shutter, hinges type B-21 100mm long (02 Nos) suitable handle (01 No) with powder coating of any colour (thickness of powder coating not less than 50micron) etc complete all as specified and directed.Note: Only Glass and wiremesh will be measured and paid seperately. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 21, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 18 daysOct 23, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 20 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender