Tender For Special Repair To Other Rank Md Accn Bldg No P-238 (09 X Qtrs) At Rt Lines Of 11 Csr Under Ge (West) Jrc
Tender Value
44.73 Lakhs
Estimated cost
Bid Submission
20 Oct 2026
17 days left
EMD
89460
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Jalandhar → Punjab
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Special Repair To Other Rank Md Accn Bldg No P-238 (09 X Qtrs) At Rt Lines Of 11 Csr Under Ge (West) Jrc
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete(unreinforced) in ground floor and paving n.exc 15 cm thick (below or above ground level complete . |
| 2 | Demolition of brick or stone masonary built in cement mortar complete |
| 3 | Taking down cement plastering on stone wall/brick wall etc including racking out of joints hacking for key scrubbing down with water etc |
| 4 | M&L brick work with sub-class 'B' bricks, straight or curved on plan exceeding 6 M mean radius built in CM 1:6. |
| 5 | M&L brick work with sub class B bricks, straight or curved on plan to any radius in half brick thick wall built in CM 1:4 complete all as spd and directed |
| 6 | M&L Cement concrete type D 2, 1:4:8 (using 40 mm graded stone aggregate) in sub base of flooring, hard standing,Manhole, drain etc. |
| 7 | M&L 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggr) as in plinth protection/path finishing the surface even and smooth without using extra cement complete all as spd and directed. Note : Plinth protection shall be laid in (1:20) slope. The concrete shall be laid at a stretch not exceeding 3metre in length. Joint gap between adjoining slab, at corners and at junctions of walls shall not exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen 85/ 25 grade mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3 metre interval at corner and as junction of walls. |
| 8 | M&L for 25mm thick Sand coushening under paver block complete all as specified and directed. |
| 9 | M&L machine pressed precast coloured concrete coloured interlocking paver blocks any shape and size confirming of IS 15658 : 2006 of 60mm thick , M-35 laid and jointed with grey cement and pigment. |
| 10 | M&L Chequered cement concrete tiles 30cmx30cmx25mm thick as in path etc. set and jointed with grey cement and pigments as in floors and over and incl screed bed or bedding layer of mortar 15mm thick laying floor finished in CM 1:6 complete all as specified and directed |
| 11 | M&L for Plain Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) cast in situ in kerbs or mud stops, rounded or chamfered on edges of paving blocks as directed including use and waste of form work. |
| 12 | M&L 10mm thick rendering in CM 1:3 on brick/concrete surface as in ceiling and finishing the surface even and smooth with out using extra cement. |
| 13 | M&L 15mm thick rendering with water proofing liquid as per manufacturere instruction of approved make : Like : Sica/Dr Fixit/Fosroc or equivalent to approved make on wall in CM 1:4 on brick/concrete surface and finishing the surface even and smooth with out using extra cement. |
| 14 | M&L 15mm thick rendering on wall in CM 1:6 on brick/concrete surface and finishing the surface even and smooth with out using extra cement. |
| 15 | Demolition of floor hearth or wall tiling including cement mortar bedding (not backing ) removing serviceable tiles to store and rubbish of the premises |
| 16 | M&L coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over 10 mm thick cement plaster in CM 1:4. |
| 17 | M&L Non skid Coloured ceramic tiles 7 to 8 mm thick (squre or rectangle) area of each tile exce 0.11 SqM but not exceeding 0.18 SqM in floors etc, set and jointed in neat cement slurry and pinted in white or coloured cement to match with including 15mm thick screed bed in CM 1:6. |
| 18 | Non - skid Ceramic tiles 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match in floors etc, set and jointed in neat cement slurry and pinted in white or coloured cement to match with including 15mm thick screed bed in CM 1:6. |
| 19 | All as per above 18 but in skirting over 10 mm thick cement plaster in CM 1:4. |
| 20 | M&L Machine cut kota stone slab flooring 18 - 20mm thick over 20mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing upto mirror finished complete. |
| 21 | M&L Machine cut kota stone slab flooring 18 - 20mm thick as in skiritng, riser of steps etc laid over 10mm thick cement plaster in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing upto mirror finished complete. |
| 22 | Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for |
| 23 | Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces of concrete |
| 24 | M&L mild steel deformed bars 8mm dia and over cut to length bent to shape required including cranking bending and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips confomring to Gd I IS-432 |
| 25 | Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any morter. |
| 26 | M&L 20mm Granite (of any type) work(table rubbed and polished) in steps, jambs , pillars, window cills, cooking platforms, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over 15mm thick cement screed bed in CM 1:4 complete all as spd and directed. |
| 27 | Rounding/moulding to edges of Kota stone slabs, marble stone, granite stone slabs one edge, such as in steps, cooking platform , and other similar situations etc |
| 28 | Demolition of cement concrete above ground floor and paving exc 15 cm thick (below or above ground level complete . |
| 29 | M&L Plain Cement Concrete Type A0 1:1.5:3 (using 12.5 mm graded stone aggregate) |
| 30 | M&L for 15mm thick rendering in 1:3 CM with water proofing liquid as per manufacturere instruction of approved make : Like : Sica/Dr Fixit/Fosroc or equivalent to approved make as in sunken portion complete all as directed. |
| 31 | M&L for applying evenly a tack coat of industrial bituminous 85/25 @ 1.20 Kg per squqre mtr including cleaning surfaces. |
| 32 | M&L APP based polymeric membrance minimum weight not less than 3.0kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150gms/sqm) land on primed surface by forced application(complete area sealed by gas flame) with over lap of 15 cm complete all as specified and directed complete all as spd and directed. |
| 33 | M&L Cement concrete type E-2, 1:5:10 using 40mm graded brick aggregate in foundations filling and mass concrete as in sunken floor. |
| 34 | Cutting holes into or through brick walls built, in cement mortar Superficial area N.exc 150 sq. cm upto 23cm of depth of wall, |
| 35 | M&L for 50mm dia GI pipe,med grade beveled cut at both ends by making hole in walls sunken portion aprox above the RCC slab and ceiling finished the hole with cement plaster 1:2 to match with existing surface complete etc.(Measured for cutting holes shall be paid in concerned sch item) |
| 36 | Taking down chowkats or frames with shutters (without taking of shutter from the frame)of any description alongwith fittings n.exc 1.5sqm each |
| 37 | Taking down chowkats or frames with shutters (with out taking of shutter from the frame) of any description alongwith fittings exc 1.5sqm n.exc 4 sqm each |
| 38 | S&F pressed steel door frame with one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 105 x60mm |
| 39 | S&F pressed steel door frame with one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 125 x60mm |
| 40 | M&L for PCC Type B0-1:2:4 using 12.5mm graded aggregate as in filling of pressed steel frame, hold fasts and similars articles |
| 41 | Cutting holes in brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required built in cement motar in brick wall depth of embedded portion of holdfast exc half brick but n exc one brick |
| 42 | S&F 2nd class hardwood rail and style, factoy made plain,framed,panelled shutters (two panel) 35mm thick, with lock rails and panel of 9mm B. W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rails and stile as per IS : 1003 (Part-I), kiln seasoned and chamically pressure treated. |
| 43 | S&F 2nd class hardwood glazed and skelton door shutters 35 mm thick divided into squares open rebated and prepared to receive glass, gauge etc edges of framing plain, chamfered, rounded tfitted with mltred beads for securing glass etc, size of members as specified in SSR Pt 1 section 8 clause 8.20 (b) supplied and fitted to chowkats with plain, chamfered or rounded mitred and rebated bars any numbers. |
| 44 | Material and labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc.including welding grinding,buffing,polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete including fixing the railing with necessary accessories and stainless steel dash fasteners,stainless steel bolts etc,of required size, on the top of floor or the side of waist slab with suitable arrangement. |
| 45 | Dismantling of unframed timber scantlings in fillets, rails, posts, rafters, purlins,etc. under 40 sq. cm in section in any position |
| 46 | Dismantling boarding, any description, fixed in any position with nails |
| 47 | S&F Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/Ceosetory windows & other Frames/ Chowkhat of size Frame size 50 x 100 mm for wardrobe, one or more rebates comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum comp- ressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made |
| 48 | S&F Factory Made Solid PVC Moulded Door Shutter With Core free EPS, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on the front face & 2mm prelam PVC Sheet on back face, supplying & fixing in frame at site as per specification & drawing. |
| 49 | Providing and fixing factory made 18mm thick solid, decorative, WPC(Wood Polymer Composite) laminated board of required size as in wordrobe shelf comprising of virgin polymer of K value 57-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives made from extrusion process WPC foam sheet single extruded (inner with having minimum density not less than 650 kg/cum and screw withdrawal strength of 2000 N (Face) & 1100 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of board and fixing with solid, WPC(Wood Polymer Composite) batten as required size and fixed with necessary full body threaded star headed counter sunk S.S screws, all as per direction . |
| 50 | Solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube |
| 51 | S&F factory made solid panel pvc door shutter 30mm thick (style) consisiting of frame made out of M.S. Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at the site as per specification & drawing. |
| 52 | M&L Powder coated aluminium (Thickness of main aluminium section not less than 1.60mm and minimum thickness of powder coating 50 micron) for sliding window shutters including providing and fixing roller, three track system, locking arrangement fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws where necessary all complete as per architectural drawings and the directions. |
| 53 | Steel window/ventilator 1.25 mm thick Box type ERW hollow P section of size 60mm x 25 mm single rebated comprises skelton shutter ERW Sec 50 MM x 20 mm and 1 mm thick and two openable leaf consisting two Nos sash bar of T-section 20 mm x 3mm complete welded to frame with one vertical mullion of ERW box type T section of size 60mm x 25 mm and 1.25 mm thick including cuttings holes and making good dismantled portion in PCC (1:2:4) type B-1, including shop coat primer and following fittings welded to shutters:-i) Hold fasts 150 mm long,12mm x 3mm made to shape -04 No’s, (ii) Handle of Z sec 20mm x 25mm , 100mm long per leaf -1 No’s (iii) MS tower bolt 150 mm long per leaf -2 No’s (iv) Z sec 20mm x 25 mm , 100 mm long stopper per leaf -1 No (v) Cleat 55 mm long of hollow square 15mm x 20mm x 63 mm welded to hinges per leaf -01 No (vi) MS pintal hinges of size 75mm x 12 mm per leaf -02 Nos (vii) Fabrication and fixing arrangement complete |
| 54 | All as per item No 53 above but glazed shutter. |
| 55 | S&F framed work such as grills & gates, gratings with ends of bars shouldered on forged in spickes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, rallings, framework of water tanks and similar work conforming to Fe-290 Gde-E-165 |
| 56 | S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and avg erage with aperature 1.18 mm fixed with tinned tacks, or galvanised wire staples. |
| 57 | M&L for 4.80mm thick sheet glass ordinary quality glazing with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed. |
| 58 | S&F Butt hinges, medium weight cold rolled 100 mm size ISI marked. |
| 59 | S&F aluminium anodised barrel tower bolts of extruded section 150mm long all as specified/ |
| 60 | S&F Extruded aluminium alloy handles fabricated type anodised 150mm size |
| 61 | S&F aluminium alloy anodised sliding door bolts 250 mm long with hasp, staple (bolt type)and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections as specified. |
| 62 | S&F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete. |
| 63 | S&F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor 150 mm |
| 64 | S&F in repair for mild steel pipe 25 mm dia Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc as approved complete all as specified. |
| 65 | S&F in replacement 100 mm hasp and staple aluminium anodised including bolt to hinge plate and fixed with screw complete all as specified. |
| 66 | Providing and fixing solid PVC Kitchen Cabinet of size 1845 x 770 x 620mm at site made out of 18mm thick one side decorative lamination and other side balancing lamination sheet consisting of car case 18mm thick pvc sheet and provision of shutter made out of 18mm thick one side decorative laminated PVC sheet all required brackets SS screw etc. the panel shall be febricated using adhessive and screws where ever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bend finish as per make and specification mentioned as per drawing and specification. |
| 67 | Taking up or down 15 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed. |
| 68 | Taking up or down 20 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed. |
| 69 | S&F 15mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed. |
| 70 | S&F 20 mm bore GI tubing medium grade fitting complete to wall and ceiling or laid in floor complete all as specifed and directed. |
| 71 | Cutting chases, pinning in making good to facings where reqd and pointing in cement mortar 1:3 to ends or edges of shelves , for water tubing etc and making good, cutting exc 10cm girth but not exc 20cm girth in stone walls |
| 72 | Dismantiling of water tanks of capacity exc 250 & n exc 500 ltrs incl all necessary fittings complete. |
| 73 | S&F 500 ltrs PVC rotational moulded polyethylene water storage tanks double layer made (cylindrical vertical with closed top ) hoisted and fixed in position all as spd in SSR part-I |
| 74 | S&F 20mm Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair |
| 75 | S&F ball float valve brass with epoxy coated aluminimum rod for 20 mm bore pipe high pressure with polythelene high density float and complete screwed for iron pipe. |
| 76 | S&F in repair 15mm dia long body Bib taps cast copper alloywith fancy type chromium lated crutch or butterfly handle screwed down, scewed for iron pipes or for brass ferrule |
| 77 | S&F in repair 15mm brass CP bath mixer for mixing hot & cold water screwed down for iron pipe and fixed. |
| 78 | S&F in repair 15mm brass CP WHB/Sink mixer swan neck for mixing hot & cold water screwed down for iron pipe and fixed. |
| 79 | S&F 15mm dia Brass stop valves chromium plated, fancy type with long shank and cup concealed type screwed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlori as specified and fixed in repairs. |
| 80 | S&F 15mm dia Brass stop valves chromium plated, fancy type with cup screwed down, highpressure with crutch or butterfly handle, screwed both ends for iron pipe or for unlons as specified and fixed in repairs. |
| 81 | S&F 600x450 bevelled edged looking mirror 2mm thick of selected quality glass, mounted on 4 mm thick PVC sheet and with aluminnium frame work fitted with chromium plated brass screws and cup washers including taking old one. |
| 82 | S&F in repair Vitreous china wash hand basin (550X400mm) white, flat back excluding taps, including brackets &32mm waste cuppling complete all as specifed and directed. |
| 83 | S&F Vitreous China Water closet (Squatting pattern) \\"Orissa Pattern\\" size 580x 440 mm white with 'P' or 'S' trap, front or back inlet and foots rests any pattern (excluding flusing cistern and flush pipe) in repairs complete. |
| 84 | S&F 10 Litre PVC valveless syphonic action flushing cistern low level white with inlet ball valve, float and handle including brackets and flush pipe of polyethylene of low or high density or PVC 32 mm dis for low level cistern in repairs |
| 85 | S&F 15mm PVC connection 450mm long with PTMT nuts of superior quality as specified |
| 86 | Supply and fixed CP Soap dish, any type fixed to walls with plugs with chromium plated brass screws |
| 87 | Supply and fixing for glass Shelf with stainless steel railing and 8mm premium quality black glass shelf of size 450mm x 150mm complete all as specified and directed. |
| 88 | S&F for brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges etc complete all as spd and directed. |
| 89 | M&L 75mm PVC (SWR) floor trap , plain with CP grating including jointing with solvent cement complete all as spd and directed |
| 90 | S&F in repair brass chromium plated shower rose 125mm size complete all as spd and directed. |
| 91 | Supply in fixing in repairs sink with drainage board made Stainless steel 1mm thick kitchen or laboratory with plugs, washer and wastes pipe , including bedding in cement mortar on dwraf wall or including fixing cantilever brackets and connecting union pipe, over all size 915mm x 460mm bowl size 410mm x330mm x160mm. |
| 92 | S&F in replacement stainless steel kitchen plate rack, made out of 1mm thick stainless steel size 36\\" x 30\\" x 10\\" (Miinimum weight 7 Kg) with shelves and plate position as approved complete all as specified and directed. |
| 93 | Dismantling of brick tiles single layer as in roof covering complete all as specified |
| 94 | Demolition of mud in roofs any thickness including plastering and leeping(whether full thickness removed or only a part thereof) all as specified. |
| 95 | Cleaning/Roughening surfaces of old concerete floor/roof by picking , sweeping clean and washing down with water to romove the dust etc complete all as spd. |
| 96 | M&L PCC 1:2:4 type B0 using 12.5mm graded stone agg in padding Complete all as specified and directed. |
| 97 | M&L 10mm thick rendering on top of roof slab in cement mortar 1:4 with using appropriate WPC as per manufacturer's information from SIKA Plastocrete Plus/FOSROC/ DR Fixit/ STP/CICO on brick/concrete surface, finishing the surface even and fair without using extra cement. |
| 98 | Providing and applying liquid Polyurea-PU based hybrid elastomeric water proofing membrane at existing/newly constructed roofs, RCC structure like basement raft, retaining wall, water retaining structure, tunnels/subways and bridge deck etc. in two or more coats. The product must have pot life of >90 mins., tensile strength > 12.6 Mpa, elongation of > 500% conforming to ASTM D 2370 & puncture resistance of >200 N as per ASTME 154 with min. consumption of 1.5 Kg per sqm for 1.2mm DFT in two- three coats. The surface needs to be primed with water soluble self impregnated epoxy primer in two coats to be applied @ 200-250 gms/sqm/coat prior to Polyurea -PU application. Furthermor, (in case the substrate is not suitable) 15mm plaster is advisable for surface prepration before application of the water proofing membrane to avoid pinholes or functional difficulties of the system (Make - Asian Paints, BASF & SIKA or equivalent to approved make) Note:- The application shall be done by the authorised applicator of the manufacture with a letter of proof stating the authenticity of the applicator firm. |
| 99 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) |
| 100 | Dismantling of cast iron or reinforced concrete drain pipes of size 75-100mm dia, jointed in cement mortar and taking out of trenches, if required. |
| 101 | S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints,fixed to walls complete |
| 102 | S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls |
| 103 | S&F110mm PVC (SWR) bends |
| 104 | S&F75 mm PVC (SWR) bends |
| 105 | S&F for PVC 110mm (SWR) vent cowl |
| 106 | M&L for repairing of R.C.C projections, chajjias, roof slab, facia etc in patches not exceeding 3 Sqm in each patch by necessary preparation. Scarpping, cutting, chiseling derusting and cleaning exposed reinforcement, surfaces of damaged, loose R.,C.C surfaces and applying one coat of rust stop solution of approved make and filling the surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggreagates and reinforced with welded TMT bars/mesh (If Reqd) of weight exc 2 kg per sqm but n.exc 3kg/sqm with or without facia and finished with cement and sand motar (1:3) using coarse sand and thickness of R.C.C member n.exc 100mm including necessary form work and applying two coats of finishes to match with the existing surfaces in at any height complete all as specified and directed(Note : Cost of form work and welded mesh shall be deemed to be included in unit rate quoted by the contractor complete all as specified and as directed. |
| 107 | Excavation in trenches not exc 1.5m wide and not exc 1.5m deep for foundation etc for shafts, wells, cesspits , manholes pier holes, etc n exc 10 sqm on plan and n exc 1.5m in depth and getting out in soft/loose soil complete all as specified and directed. |
| 108 | Returing, filling including spreading, leveling, watering and well ramming in layers not exceeding 25 cms in soft /loose soil. |
| 109 | Removing excavated material n exc 50 m depositing where directed at a level n exc 1.5m above the starting point complete all as spd. |
| 110 | Demolition and breaking up drain pipes 150mm bore (salt glazed ware, AC or Reinforced) set in cement mortar all as spd and directed |
| 111 | M&L for 150mm bore SGSW drain pipe (Grade-A) laid in trenches and jointed in CM 1:1 and tested complete all as spd and directed |
| 112 | M&L for concrete bed for 150mm in PCC 1:3:6 type C-2 (using 40 mm graded stone aggregate) to drain pipes including packing under,haunching against the sides of pipes after they are laid and tested complete all as specified and directed. |
| 113 | Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for |
| 114 | M&L RCC 1:2:4 type B-1 (using 20 mm graded stone aggregate) as in precast RCC manhole / septic tanks ,drain,covers including all form work and setting in CM 1:4 all as specified and shown on drgs. |
| 115 | M&L mild steel deformed bars 8mm dia and over cut to length bent to shape required including cranking bending and binding with and including mild steel wire annealed not less than 0.9 mm dia or securing with clips confomring to Gd I IS-432 |
| 116 | Material and labour for cement concrete 1:2:4 Type B-1using 20 mm graded stone aggregate as in copings, weathering, slightly rounded or chamfered angles and throating, complete all as specified and as directed. |
| 117 | M&L for applying two coat of synthetic enamelled paint over one coat of pink primer including preparation of new wood surfaces of any description not otherwise described over 10 CM girth or width all as directed. |
| 118 | M&L for applying two coat of synthetic enamelled paint over one coat of red oxide primer including preparation of new steel surfaces of any description not otherwise described over 10 CM girth or width all as directed. |
| 119 | M&L for applying white wash of 3 coats on ceiling incl preparation newly plastered surfaces as specified and directed. |
| 120 | Complete removal of existing treatment and applying Two coat of white wash on ceiling incl preparation old plastered surfaces as specified and directed. |
| 121 | M&L for applying white wash of 3 coats on walls incl preparation newly plastered surfaces as specified and directed. |
| 122 | Complete removal of existing treatment on wall and applying Two coat of white wash incl preparation old plastered surfaces as specified and directed. |
| 123 | Material and labour for preparation of new plastered surfaces on walls and applying two coats of oil distemper over one coat of chalk whitening complete all as specified. |
| 124 | Complete removal of existing treatment on wall and applying Two coat of Oil distemper (white or tinted) on old plastred surfaces including preparatory to distempering on walls etc (Surface finished even and smooth) complete all as specified and as directed. |
| 125 | Material and labour for preparation of new plastered surfaces on walls and applying two coats of cement base paint over one coat of cement primer complete all as specified. |
| 126 | M&L for Complete removal of existing treatment on wall and applying Two coat of of cement base paint on old plastred surfaces including preparatory to distempering on walls etc (Surface finished even and smooth) complete all as specified and as directed. |
| 127 | Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete including fitting such as switches, ceiling roses, socket, light fittings, regulators etc complete and making good disturbed surfaces of walls, floors and floors and one coat of putty and two coat of distemper as per existing colour complete all as directed . |
| 128 | Taking down sub main wiring of two single core PVC cable PVC insulated 4 / 6/10 sqmm including conduit or wooden batten and remove from the site of work and making good the disturbed surfaces of wall or floor etc. and one coat of putty and two coat of distemper as per existing colour complete all as directed. |
| 129 | Taking down main switch / DB and making good the disturbed surface and one coat of putty and two coat of distemper as per existing colour complete all as directed. |
| 130 | M&L for point wiring with 1.5 sqmm, PVC insulated but sheathed, stranded copper conductor single core FRLSH cable, IS-694 marked, drawn through and including non metallic rigid PVC concealed conduit medium grade 20mm dia (minimum) or higher size as specified and cutting chasing on wall complete with all PVC conduit accessories such as socket, elbow, junction box, bell mouth, reducer, bend and flexible conduit etc/ fittings ISI marked for modular fittings and brass screws and cup washers including 1.5 sqmm stranded copper conductor PVC insulated FRLSH cable green in colour as continuous earth conductor connected to common earth and earth dolly with all accessories complete all as specified and directed. Note : Cost of Metal boxes and modular accessories like cover plates will be paid seprately in respective items)(a) One light / fan/bell point controlled by one, one way switch complete all as specified.. |
| 131 | (b) One 3 pin socket out let 5 Amps on same board with other switches complete all as specified.. |
| 132 | (c)One 3 pin socket out let 5 Amps on the independent board complete all as specified.. |
| 133 | All as per item No.130 above but with 2.5 sqmm multistranded copper multistranded conductor FRLSH cable with 2.5 sqmm earth wire for one 6 pin socket outlet 15 amps on independent board complete all as specified. |
| 134 | Supply and fixing modular metal flush box 1/2 module complete all as specified and directed. |
| 135 | Supply and fixing modular metal flush box 3 module complete all as specified and directed. |
| 136 | Supply and fixing modular metal flush box 4 module complete all as specified and directed. |
| 137 | Supply and fixing modular metal flush box 6 module complete all as specified and directed. |
| 138 | Supply and fixing modular metal flush box 12 module complete all as specified and directed. |
| 139 | Supply and fixing modular white cover plate with frame, 1 module complete all as specified and directed. |
| 140 | Supply and fixing modular white cover plate with frame, 3 module complete all as specified and directed. |
| 141 | Supply and fixing modular white cover plate with frame, 4 module complete all as specified and directed. |
| 142 | Supply and fixing modular white cover plate with frame, 6 module complete all as specified and directed. |
| 143 | Supply and fixing modular white cover plate with frame,12 module complete all as specified and directed. |
| 144 | Supply and fixing modular Dummy plate complete all as specified and directed. |
| 145 | Supply and fix in replacement Modular switch 6 Amps single pole one way as per existing make & model/ as per sample. |
| 146 | Supply and fix in repair Modular switch 16 Amps single pole one way as per existing make & model/ as per sample. |
| 147 | Supply and fix Modular multi socket 3 pin and 2 pin 6 Amps round and flat as per existing make & model/ as per sample. |
| 148 | Supply and fix in repair Modular socket 6A /16 A Twin socket heavy duty as per existing make & model/ as per sample. |
| 149 | Supply and fix bell push flash Modular type 5 amps complete all as specified. |
| 150 | Supply and fix bell ding dong 230 Volts AC single pole complete all as specified. |
| 151 | M&L ceiling rose surface bakelite 65 x 50 mm three terminals complete all as specified. |
| 152 | Supply and fix MCB DB, TPN 6 way double door Vertical type suitable for mounting of MCCB as incomer with suitable 200 amps rated bus bars , Neutral links , blanking plates Distribution boards should be Double Door design with IP-43 and IK-08 rating as per IEC 61439-3 with 200 Amp fully insulated copper busbars, insulated neutral bar, earth bar and cable ties for cable management. Distribution board should be supplied with door earthing, prefitted masking sheet, reversible doors and pan assembly for easy installation. Must have possibility of converting lock to panel lock complete all as specified and directed by EIC . complete all as specified and directed. All 3 Phase horizontal distribution boards should have the provision to convert the distribution boards to Per Phase Isolation Distribution Board at site. All MCCB incomer distribution boards should be supplied with 250 Amp rated fully shrouded busbars. |
| 153 | Supply & fixing MCCB 4 pole of capacity 100 Amps with breaking capacity 16 Kilo Amps including all electrical connections and fixing arrangment complete all as specified and directed by EIC . Note- MCCB Should have reverse load and line termination, rotary handles – direct and variable depth and common auxiliaries for entire range. Should be CE marked and conform to IEC 60947-2. MCCB should have the maximum operational voltage ( Ue ) of 550 Volts (AC 50/60 Hz), Insulation Voltage ( Ui ) of 800 Volts and Rated Impulse Withstand Voltage (Uimp) not less than 8000 volts. The MCCB should have been designed at an ambient temperature of 50 degree centigrade. MCCBs shall be actuated by a rotary-handle that clearly indicates the three distinctive positions: ON, OFF and TRIPPED.For 16 – 125 A: Should have breaking capacity of min. 16 kA with thermal release adjustable from 80 to 100 % & fixed magnetic release and with Ics = 100% Icu. |
| 154 | Supply and fix MCB DB, TPN 4 way double door Vertical type suitable for mounting of MCCB as incomer with suitable 200 amps rated bus bars , Neutral links , blanking plates Distribution boards should be Double Door design with IP-43 and IK-08 rating as per IEC 61439-3 with 200 Amp fully insulated copper busbars, insulated neutral bar, earth bar and cable ties for cable management. Distribution board should be supplied with door earthing, prefitted masking sheet, reversible doors and pan assembly for easy installation. Must have possibility of converting lock to panel lock complete all as specified and directed by EIC complete all as specified and directed. All 3 Phase horizontal distribution boards should have the provision to convert the distribution boards to Per Phase Isolation Distribution Board at site. All MCCB incomer distribution boards should be supplied with 250 Amp rated fully shrouded busbars. |
| 155 | Supply & fixing MCCB 4 pole of capacity 63 Amps with breaking capacity 16 Kilo Amps including all electrical connections and fixing arrangment complete all as specified and directed by EIC . Note- MCCB Should have reverse load and line termination, rotary handles – direct and variable depth and common auxiliaries for entire range. Should be CE marked and conform to IEC 60947-2. MCCB should have the maximum operational voltage ( Ue ) of 550 Volts (AC 50/60 Hz), Insulation Voltage ( Ui ) of 800 Volts and Rated Impulse Withstand Voltage (Uimp) not less than 8000 volts. The MCCB should have been designed at an ambient temperature of 50 degree centigrade. MCCBs shall be actuated by a rotary-handle that clearly indicates the three distinctive positions: ON, OFF and TRIPPED.For 16 – 125 A: Should have breaking capacity of min. 16 kA with thermal release adjustable from 80 to 100 % & fixed magnetic release and with Ics = 100% Icu. |
| 156 | Supply and fix Sheet metal DB,double door, SPN 8 way for MCB, 240 volt with 200 amps rated bus bar , neutral bar / connectors suitable copper thimbles , lugs etc. Distribution boards should be Double Door design with IP-43 and IK-08 rating as per IEC 61439-3 with 100 Amp fully insulated copper busbars, insulated neutral bar, earth bar and cable ties for cable management. Distribution board should be supplied with door earthing, prefitted masking sheet, reversible doors and pan assembly for easy installation. Must have possibility of converting lock to panel lock complete all as specified and directed by EIC . |
| 157 | S&F MCB SPN, 240 volts, 40 to 63 Ampere, rupturing capacity 10 KA, ‘B’ curve type ,MCB should be having the Breaking Capacity of 10 kA and should be ISI marked as per IS/IEC 60898-1 2002 with “B” Curve Characteristics. Should have bi-connect terminals on the bottom terminals for looping and should have 35 sq mm termination capacity on both terminals with insulated sliding shutters for making it IP-20 protected & with two position DIN Rail Clamp for easy mounting. complete all as specified and directed by EIC. |
| 158 | Supply & Fixing MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type ,MCB should be having the Breaking Capacity of 10 kA and should be ISI marked as per IS/IEC 60898-1 2002 with “B” Curve Characteristics. Should have bi-connect terminals on the bottom terminals for looping and should have 35 sq mm termination capacity on both terminals with insulated sliding shutters for making it IP-20 protected & with two position DIN Rail Clamp for easy mounting. complete all as specified and directed by EIC. |
| 159 | Supply and Fixed single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of cap 20A complete all as specified and directed. |
| 160 | M&L for sub main wiring with four single core PVC insulated and unsheathed cable 10 sqmm with multi stranded copper conductor , FRLSH type cable drawn through and including PVC concealed conduit of suitable size complete with all accessories alongwith provn of 2 run of 10 sqmm PVC insulated and unsheathed ,multi stranded copper conductor , FRLSH type cable as earth wire. (Six runs of cable and one run of conduit shall be measured as one length) |
| 161 | M&L for sub main wiring with two single core PVC insulated and unsheathed cable 6 sqmm with multi stranded copper conductor , FRLSH type cable drawn through and including PVC concealed conduit of not less than 25mm in size complete with all accessories alongwith provn of 6 sqmm PVC insulated and unsheathed ,multi stranded copper conductor , FRLSH type cable as earth wire.(Three runs of cable and one run of conduit shall be measured as one length) |
| 162 | M&L for submain wiring with two RUNS of single core 4 sqmm for main wire and one run of single core 4 sqmm as earth wire of stranded FRLSH copper conductor PVC insulated unsheathed cables drawn through and including concealed conduits in wall and necessary cutting and chassing for rigid PVC conduit ISI marked not less than 20 mm dia and all accessories complete all as specified & directed. (Three runs of cable and one run of conduit shall be measured as one length) |
| 163 | Supplying and fixing 1100 volts grade heavy duty cable for Connection to Security lights directly through Panels, PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers/Clips not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular of size 6 Sqmm 2 Core complete. |
| 164 | M&L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings all as specified and directed. |
| 165 | S&F LED bulb 12 Watt White(6000K-6500 K)/Warm(2700K-3200K) with BEE Energy star rating of FIVE star and emission of minimum 100 lm/W complete all as specified. |
| 166 | S& F in replacement LED tube set (fitting) 20 W use and through type with internal surge protection device of 4 KV with voltage band 140-280V with LED rod with fixture box type and making electrical connection to ceiling rose all as directed |
| 167 | S&F SITC of high-quality integrated LED Street Light with a minimum system lumen of4750 Lm and system wattage not exceeding 45W with a nominal efficiency 105 lumen/watt. CCT of 5700K with SDCM of < 5 and CRI >70. The housing should be of non-corrosive high-pressure die-cast aluminum with high efficiency LEDs as lighting source and lens embedded PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 with PF > 0.95. Lifetime of 50K hours @L70. The Luminaire should have Powered by integral, Isolated LED electronic driver (SMPS based constant current supply) with lower THD, Output Open / Short Circuit protection, Phase to Phase protection (Operation at 440 V AC), Over Voltage protection, Surge Voltage protection upto 4 kV.Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/ULaccredited lab to verify above parameters complete all as specified and directed.. |
| 168 | Supply and fix of hexagon shaped LED bulkhead industrial luminaire with Pressure die cast housing and Polycarbonate diffuser and silicon gasket. The luminaire should have a color CRI > 80, and CCT of 5700K. The luminaire shall be compliant with IP66 & IK 10 classification. Luminaire shall be designed to emit at least 1000 nominal lumens at a system efficacy of at least 100 lumen/watt with a maximum system wattage of 10 Watts. The electronic driver used shall have a power factor >0.95 and THD <15% and suitable for an operating voltage range of 180-270V AC and 4 Kv inbuilt surge protection. Manufacturer shall have in house lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/UL accredited lab to verify above parameters. |
| 169 | Taking down existing electric/electronic energy meter any capacity/type carefully all electric wire/submain complete and refixing the same, incl electric connection with new gutties/anchor fastener if required complete all as specified and directed. |
| 170 | Supply & fIX Water Heater storage type, five star rated, electric operated, 25 Ltr capacity 230Volt AC Supply with PVC Connection pipe Superior quality (HOT & Cold water ) including Plug top 15 Amp, NRV complete with necessary water connection and electrical connection complete all as specified and directed. |
| 171 | Supply and fixing ceiliing fans Copper winding in replacement complete with blades, down rod , electronic regulator switch type 5 step and accessories 230V, 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE, Five star rated with brushless direct current motor (BLDC) complete all as specified and directed. |
| 172 | M&L for earthing complete with GI steel earth plate electrod 60x60cmx6.00mm thick bouried directly in ground /earth pit not less than 2.25m deep below the ground level with top edge of the plate not less than 1.5 m below the normal ground level connected to test point by using GI wire of dia 4 mm as earthing lead soldering/revated to earth plate at one end and connected DB by means of nut, bolts etc complete with PCC pit (1:3:6) type GI cover with handle funnel with watering pipe wire mess GI protection pipe for earthing lead all complete as specified and as per electric plate No.5 of SSR Part I |
| 173 | Taking down carefully old unsv cable of any make/type all as directed. |
| 174 | Supply and laying XLPE insulated , armoured electric cable heavy duty with aluminium conductor , 1100 volts UG cable of size 4 Core 50 Sqmmm, |
| 175 | Supply and lay burnt bricks sub class 'B' standard size laid across the cable in trenches as protection to the cable all as specified and directed. |
| 176 | Supply and laying GI Tube Med grade 100 mm dia all as specified and directed. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Oct 01, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 20, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 17 daysOct 27, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 24 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender