Tender For Construction Of Anganwadi Building Works Under C.S.R Fund 2026-27 - Nilakkottai Block - Tn-05-01
Tender Value
12.50 Lakhs
Estimated cost
Bid Submission
08 Oct 2026
7 days left
EMD
12500
Bank guarantee accepted
Document Fee
Ref. Documents
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Dindigul → Tamil Nadu
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of Anganwadi Building Works Under C.S.R Fund 2026-27 - Nilakkottai Block - Tn-05-01
BOQ
| Sl. No. | Item Description |
| 1 | Name of the Work : Construction of Anganwadi building at Uchanampatty H/O Nariyuthu Est Amount Rs : 12.50 Lakhs |
| 2 | Earth work excavation for foundation in all soils and sub soils to full depth etc., ordinary soil complete |
| 3 | Supplying and filling in foundation, basement, etc with filling M.Sand in layers of not more than 15 cm thick well watered, rammed and consolidated etc. complete complying with standard specification and as directed by the departmental officers. |
| 4 | Refilling in foundation and basement with excavated earth in layer of not more than 15cm thick |
| 5 | Cement Concrete 1:4:8 (One Cement, Four M.Sand and eight hard broken stone jelly) using 40 mm gauge hard broken granite stone jelly for foundation including dewatering wherever necessary and laid in layers of not more than 15 cm thick, well rammed, consolidated and curing etc. complete complying with standard specification |
| 6 | Brick work in cement mortar 1:5 mix using country bricks 83/4\\"x41/4\\"x23/4\\" including cost and conveyance of all materials to site and all labour charges etc complete (Below Basement) |
| 7 | Brick work in cement mortar 1:5 mix using country bricks 83/4\\"x41/4\\"x23/4\\" including cost and conveyance of all materials to site and all labour charges etc complete (Above Basement) |
| 8 | Supplying & Erecting centering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists(Country wood) of size 10 x 6.5cm spaced @ about 90cm c/c and supported by casurina props of 10 - 13cm dia. spaced @ 75cm c/c etc., complete complying with standard specifications and as directed by the departmental officers. Rate for 10m2.for the following items.(RCC floor slab, roof slab, Rectangular/ square, Tee/ Ell beams, Lintels, staircase waist slabs, Landing slabs, Landing beam, Portico beam etc., ). (Below Basement ) |
| 9 | Supplying & Erecting centering for sides & soffiots including necessary supports & strutting upto 3.29m height for plane surfaces in all floors with all cross bracings using mild steel sheets of size 90 x 60cm & 10 gauge stiffened, welded with steel angle of size 25 x 25 x 3mm for boarding laid over silver oak joists(Country wood) of size 10 x 6.5cm spaced @ about 90cm c/c and supported by casurina props of 10 - 13cm dia. spaced @ 75cm c/c etc., complete complying with standard specifications and as directed by the departmental officers. Rate for 10m2.for the following items.(RCC floor slab, roof slab, Rectangular/ square, Tee/ Ell beams, Lintels, staircase waist slabs, Landing slabs, Landing beam, Portico beam etc., ).(Above Basement) |
| 10 | Supplying & Erecting centering for sides & soffiots including necessary supports & strutting Sunshade |
| 11 | Supplying, fabricating and placing in position Mild Steel / Ribbed Tor Steel grills for all RCC works as per design given including cost of steel and G.I. binding wire in all floors etc. complete complying with standard specification. (Contractor has to make his own arrangements for the supply of steel and binding wire) |
| 12 | Cement Concrete 1:1-1/2:3 (One Cement, One and a half crushed stone M.Sand and Three hard broken stone jelly) using 20 mm gauge hard broken granite stone jelly for all RCC items of works excluding cost of reinforcement grill and fabricating charges centering and shuttering but including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor / roof slabs wherever necessary and bearing surfaces of walls, beams etc. shall be finished smooth with Cement Mortar 1:3 (One Cement and Three M.Sand) and kraft paper laid over it without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers |
| 13 | Providing granolithic floor finish of the following thickness with plain cement concrete 1:2:4 (One Cement, Two crushed stone M.Sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers. (The rate is inclusive of necessary planking for panelling wherever necessary and as directed by the departmental officers) |
| 14 | Paving the floor with best quality Vertified Tiles of size 600 x 600 x 8mm of approved colour, shade and quality laid in cement mortar 1:3 (one cement and three crushed stone M.Sand) 20mm thick in all floors and the top pointed with the white cement mixed same colour pigments etc., complete complying with standard specification. (The make and brand of the tiles should be got approved by Executive Engineer before use on works) |
| 15 | Paving the floor with pre-polished concrete anti-skid tiles (Required shape and design) of 20mm thick of approved quality and colour laid in Cement Mortar 1:3 (One Cement and Three crushed stone M.Sand) 20mm thick and pointed with white cement mixed with colouring pigment at the rate of 0.40 Kg. / sq.m., curing, etc., complete complying with standard specification and as directed by the departmental officers. (The make and brand of the tiles should be got approved by Executive Engineer before use on works) Using anti-skid tiles (Observed Data) |
| 16 | Dadooing walls with following best approved quality, white / colour glazed tiles of following sizes set in Cement Mortar 1:2 (One Cement and Two crushed stone M.Sand) 10mm thick and pointing the joints with white cement mixed with colouring pigments at the rate of 0.40 Kg. / sq.m. neatly in all floors, curing, etc., complying with standard specification and as directed by the departmental officers. |
| 17 | Weathering course in brick jelly lime concrete using broken brick jelly of size 20mm uniform gauge in pure slaked lime (no crushed stone M.Sand to be used) to the proportion of brick jelly to lime being 32:12.5 by volume and laid over the RCC roof slab in a single layer of required slope and finished by beating the concrete with wooden beaters of approved pattern, keeping the surface constantly wet by sprinkling lime jaggery water, etc., complete as per standard specification and as directed by the deparmental officers. |
| 18 | Finishing the top of roof with one course of machine pressed tiles of size 230mm x 230mm x 20mm of approved quality set in Cement Mortar 1:3 (One Cement and Three Crushed stone M.Sand) 12mm thick mixed with water proofing compound conforming to ISS at 2% by weight of cement used and the joints pointed neatly to full depth of tiles with the same cement mortar mixed with red oxide and water proofing compound including curing etc., complete complying with standard specification and as directed by the departmental officers |
| 19 | Supplying and applying of two coats of putty of 3mm thick over the exposed RCC surface of ceiling including finishing the joints smoothy with grinding machine and the surface shall be thoroughly cleaned out of dust and scrubbing. The Surface shall then be allowed to dry for atleast 48 hours. It shall then be sand papered (waterproof abrasive sheet) to give a smooth and even surface. Any unevenness shall be made good by applying 1st coat of putty mixed with water on the entire surface including filling up the undulations and applying 2nd coat of putty after 6 hours of 1st coat of putty and then sand papering (waterproof abrasive sheet) the same after it is dry and finishing the surface smoothly, etc., complete complying with standard specifications and as directed by the Departmental Officers. [ The rates are inclusive of hire charges for grinding machine with wheel, cost of sand paper (waterproof abrasive sheet), cost of putty blade, labour charges for grinding the joints and sand papering, two coat of putty, scrapping the putty area to level the surface smooth, etc., complete]. The Putty shoule be got approved by the Executive Engineer before use on work. |
| 20 | Special ceiling plastering and finishing the exposed surface of all RCC items of work such as slabs, beams, sunshades, facia, canopy slab, staircase waist slab, landing slab etc., with Cement Mortar 1:3 (One Cement and Three P.Sand) 10mm thick including hacking the surfaces, providing cement mortar nosing, beading for sunshades, staircases, steps, landing slabs and curing, etc., in all floors complying with standard specification and as directed by the departmental officers |
| 21 | Plastering with Cement Mortar 1:5 (One cement and Five P.Sand), 12mm thick in all floors including curing etc. complete complying with standard specification and as directed by the departmental officers. |
| 22 | Supplying and painting the walls with two coats of oil bound distemper over one coat of water based cement primer including cost for distemper, primer, cleaning and scrapping the walls, rendering the walls smooth with necessary putty, brushes, scaffolding arrangements, labour charges, etc., as per standard specification. (The colour and shade of the distemper shall be got approved by the Executive Engineer before use of work). |
| 23 | Painting two coats of newly plastered wall surface with ready mixed plastic emulsion paint of first class quality and of approved colour over a priming coat including thorough scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification. |
| 24 | Supplying and painting two coats new iron work such as steel doors ventilators, window bars etc., (WITHOUT PRIMER) |
| 25 | Supply and fixing of mild Steel Doors of any size with standard specification including cost and conveyance of all materials and all labour charges etc complete. |
| 26 | Steel Door (0.90 x 2.10m) |
| 27 | Supply and fixing of mild Steel Doors of any size with standard specification including cost and conveyance of all materials and all labour charges etc complete. |
| 28 | Steel Door (0.75 x 1.50 m) |
| 29 | Supply and fixing of mild Steel Doors of any size with standard specification including cost and conveyance of all materials and all labour charges etc complete. |
| 30 | Steel Door (1.10 x 2.10 m) |
| 31 | Supply and fixing of mild Steel Windows of any size with standard specification including cost and conveyance of all materials and all labour charges etc complete. |
| 32 | Steel window (1.20 x 1.30m) |
| 33 | UPVC Window Specification: Supplying and fixing UPVC (Un- Plasticized Polyvinyl Chloride) Windows of casement type (open) from the profile the size of outer frame 60mm x 58mm and shutter profile are reinforcement with GI/1mm 125GSM and 100% corrosion free, the profiles are multi chambered sections with wall thick of 2mm. The EPDM rubber (black colour) covered with over all the edges of frame and shutter the shutter will be provided with Espag multi power point locks and also it operates as handle. The corners and joints should be welded and cleaned. Radiations free pin headed plain or brown colour glass 4mm thick should be provided to the shutter and it should not allow leakage of water even at most ranging storms and should have key lockable action, security protective hinges, strong locking systems and as per size for arresting noise and energy loss. The connecting mechanism between sash and outer frame that enables opening of the window. The window should be fixed to the wall with 100% packing with screws and silicon packing all round the frames. The window should be got approved from the Executive Engineer before use on work (PWD SOR 2024-2025, P.No 109 ) (M-0674 ) |
| 34 | UPVC window (1.20 x 1.30m) |
| 35 | Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding,grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification. |
| 36 | Supply and fixing of mild Steel Ventilator of any size with standard specification including cost and conveyance of all materials and all labour charges etc complete.(Steel ventilator (0.60 x 0.45m)& 0.90 X0.45 M) |
| 37 | Steel ventilator (0.60 x 0.45m) &(0.90 x 0.45m) |
| 38 | Cost, supply and fixing of Cuddappah slab 38/40mm thick for Shelf, Cupboard and Kitchen top including cost and conveyance of all materials and labour charges etc., complete |
| 39 | Providing and fixing of PVC rain water down fall pipe 110mm dia with necessary T W Clamps, Plug, Shoes, bend, Screws, nails etc., complete |
| 40 | Provision for Electrification |
| 41 | Fan point & Light point (SD 18) |
| 42 | Ceiling fan (SD 110) |
| 43 | Supply and fixing of 4' 40W flu fitting complete with copper choke and condensor SD 88 |
| 44 | Supply and fixing of 4' 18 W LED tube light PWD SOR -M1211 |
| 45 | Exhaust fan (SD 114) |
| 46 | Plug point (SD 38) |
| 47 | Service wire (SD 66) |
| 48 | EB Metre board (SD 125) |
| 49 | Provision for Sanitary arrangements |
| 50 | Supplying & Fixing in position of baby friendly Water closet of approved quality including cost and conveance of all etc., complete |
| 51 | Supplying & Fixing in position of European Water closet of approved quality including cost and conveance of all etc., complete |
| 52 | Provision for Water supply arrangements ( pipeline & sanitary fittings arrangements) |
| 53 | 20 mm dia PVC items Finolex (or) Equivalent (with ISI Monogram) 10 kg / cm 2 |
| 54 | 20 mm dia PVC Coupler |
| 55 | 20 mm dia PVC Bend |
| 56 | 20 mm dia PVC TEE |
| 57 | PVC Screw Down Tap Heavy Type 15 mm dia |
| 58 | 110 mm PVC Pipe 6Kg /cm2 |
| 59 | 110 mm PVC TEE |
| 60 | 110 mm PVC Elbow |
| 61 | Provision for 500 litres HDPE water tank |
| 62 | Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for Ramp using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete (M-0651) |
| 63 | Provision for painting cartoons / BaLA in hall |
| 64 | Manufacturing, Supplying and Fixing of S.Steel Handrails for EWC Toilet |
| 65 | Provision for EB deposit |
| 66 | Provision for Name board Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 08, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 7 daysOct 08, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 7 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender