Tender For Construction Of New Fire Station Building At Gsl
Tender Value
Ref. Documents
Estimated cost
Bid Submission
13 Oct 2026
11 days left
EMD
19.25 Lakhs
Bank guarantee accepted
Document Fee
1180
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
goa → Goa
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for Construction Of New Fire Station Building At Gsl
BOQ
| Sl. No. | Item Description |
| 1 | EARTHWORKSFelling trees of girth(measured at a height of 1. m. Above ground level) inluding cutting of trunks and branches removing the roots stacking the serviceable material and disposal of unserviceable material for all leads : Beyond 60 cm and upto 120 cm girth |
| 2 | Earthwork in excavation by mechanical means (hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sq.m on plan) for all leads & lifts in all types of strata comprising of any type of materials either in full or part as the case may be adopting any method/methods as may be convenient as permitted (excluding blasting) in all conditions such as dry, moist, foul, saturated, submerged etc. including dressing of sides, planking and strutting, timbering, ramming of bottom, pumping and bailing out water, barricading, danger lighting, guarding and carting away excess excavated earth at the site identified by the contractor and obtaining all statuatory approvals, as directed by engineer for all lead and all lifts etc complete. |
| 3 | Earthwork in excavation by mechanical means (hydraulic excavator)/ manual means in foundation/pipeline trenches drains for all leads & lifts in all types of strata comprising of any type of material either in full or part as the case may be adapting any method/methods as may be convenient as permitted (excluding blasting) in all conditions such as dry, moist, foul, saturated, submerged etc. including dressing of sides, planking and strutting, timbering, ramming of bottom, pumping and bailing out water, barricading, danger lighting, guarding and carting away excess excavated earth at the site indentified by the contractor and obtaining all statuatary approvals, as directed by engineer for 50m lead and all lifts etc complete. |
| 4 | Refilling the pipeline/foundation trenches, plinth sides, foundation, etc.with available excavated earth in layers not exceeding 20cm in depth consolidating each layer by ramming and watering lead upto 50m and all lifts and disposal of surplus earth as directed. |
| 5 | Supplying and filling in plinth under floors, trenches including watering ramming consolidating, dressing, complete. a) Moorum |
| 6 | Disposal of surplus earth & debris upto all leads including loading, unloading and stacking, The site should be identified by the contractor and obtain all statuatory approval. |
| 7 | 2 MASONRY WORKSProviding & laying rubble packing with hard laterite stone under floors including watering ramming and consolidating etc.in pipeline trenches and other foundations complete. |
| 8 | Providing & constructing laterite masonary in neatly dressed stones for 23 cms masonary walls in cm. 1:5 (1 cement : 5 coarse sand) in foundation upto plinth level |
| 9 | Providing and laying autoclaved aerated concrete (AAC) blocks masonry with 100mm/ 115mm/ 125mm thick with Grade-I AAC blocks of density confirming to IS:2185 (Parts-3) in super structure above plinth level up to floor V with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of engineer-in-charge. (The payment of RCC band and reinforcement shall be made for seperately) |
| 10 | Providing and laying autoclaved aerated concrete (AAC) blocks masonry with 150mm/ 200mm/ 230mm/ 300mm thick with Grade-I AAC blocks of density confirming to IS:2185 (Parts-3) in super structure above plinth level up to floor V with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of engineer-in-charge. (The payment of RCC band and reinforcement shall be made for seperately) |
| 11 | Providing & constructing laterite masonary in neatly dressed stones for 23 cms masonary walls in c.m 1:4 (1 cement : 4 coarse sand) in super structure from floor I upto floor V level |
| 12 | 3 PLAIN AND REINFORCED CONCRETE WORKS Providing & laying cement concrete 1:2:4 (1 cement: 2 coarse sand: 4 graded granitic or basaltic stone aggrt. 20 mm. nominal size) excluding cost of centering, shuttering and finishing in - all works upto plinth level |
| 13 | Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer’s specification. |
| 14 | Providing and laying upto floor V level cement concrete 1:11/2:3 (1 cement: 11/2 coarse sand: 3 graded granitic or basaltic stone aggregate 20 mm nominal size) including centering and shuttering etc. - a) Kerbs, Steps and the like at or near ground level |
| 15 | b) String Courses, copings, bed plates, anchor blocks, plain window sills and the like |
| 16 | c) Small lintels not exceeding 1.5 m clear span including coping and the like requiring formwork to the suspended portions |
| 17 | Centering and shuttering including strutting, propping etc. and removal of forms for a) foundation, footings, bases of columns etc. |
| 18 | b) Vertical surfaces such as retaining walls, return walls, Partitions, walls (any thickness) including attached Pilasters, Buttresses, Plinth and string courses, Fillets and the like |
| 19 | c) Columns, Piers, Pillars, Abutments, Posts and struts (square, rectangle polygon in plan) at all levels |
| 20 | d) Sides and Soffits of beams, Beam Haunchings, Cantilever, Girders, Bressumers and Lintels plinth beams not exceeding 1m in depth at all levels |
| 21 | e) Staircases (Except Spiral Staircases) excluding landings |
| 22 | f) suspended floors, roofs, landings, shelves and their supports, balconies and chajjas at all levels |
| 23 | g) Vertical or horizontal fins individually or forming box, louvers or projected bands at all levels |
| 24 | Extra to be added for additional height in centering, shuttering where ever required with centering, shuttering where ever required with adequate bracing, propping etc. including cost of de- shuttering and de-centering at all levels, over a height of 3.5m, for every additional height of 1m or part thereof. (Plan area to be measured) Suspended floors, roofs, landings, beams and balconies (plan area to be measured) |
| 25 | Providing TMT steel reinforcement bars of SAIL, TATA. VIZAG, JSW make only (Confirming to IS 1786 of 1986) for RCC work (conforming to I.S. 1786 of 1986) including bending, binding & placing in position in all the floors along with the factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member. |
| 26 | Extra for rendering smooth the top of the suspended floors, landing and staircase (treads and risers) with cement mortar 1:2 (1 cement: 2 coarse sand) including a floating coat of neat cement and protecting the surface with a layer if 7.5 cms of earth laid over 15mm layer of fine sand in case of suspended floor and bricks laid in mud mortar in landing of steps including subsequent removal and cleaning of the same |
| 27 | Providing and laying in position machine batched concrete (BMC), machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete work including pumping of concrete to the site of laying but excluding the cost of centering, shuttering, finishing and reinforcement including admixtures in recommended proportions as per IS 9103 to accelerate, retard setting of concrete, improve workability without impairing the strength and durability as per the direction of the Engineer. M30 grade of reinforced cement conrete by using 420 kg of cement per cu.m. of concrete. All works at all floor levels. NOTE:- 1.Use of RMC is permitted at no extra cost. 2.Only digital weigh batcher to be used in case of batching at site. |
| 28 | Deduct for using less cement than the quantity as provided in the item of batch mix concrete as arrived as per the mix design. Note- This qty is negative.ie, (-)133 Qunital. |
| 29 | Supplying and fixing Pre-cast cement concrete kerb-stones(factory made,the factory should be ISO certified and registered under Dirctorate of Industries, Govt. of India) of M-20 with 20 mm nominal size granitic/basaltic aggregate properly consolidated by mechanical plat-form and vibrators with smooth finish including fixing at site complete as per specification. - Size 60 cm L x45 cm H x 15 cm T |
| 30 | Supplying and fixing of Precast RCC slabs(factory made,the factory should be ISO certified and registered under Dirctorate of Industries, Govt. of India) at site in concrete Grade of M-25 with 20 mm nominal size Granitic or basaltic aggregate, consolidated by means of mechanical platform, vibration etc. with lifting hooks of M.s. 10mm bars and PVC cups including cost of reincforcement, Certificate from manufacturer shall be produced indicating grade of concret and minimum content of steel in the product along with 5 year free replacement warranty in case of breakage complete and as directed by Engineer -in -charge. - a) Size 900 x 400 x150 mm with steel reinforcement not less than 7.0 kg per unit - 30T Capacity |
| 31 | b) Size 750 x 400 x100 mm with steel reinforcement not less than 4.2 kg per unit |
| 32 | 4 WOOD WORKSProviding and fixing wood work in frames of doors, windows, clerestory windows, trusses & other frames wrought framed and fixed in position - Second class Indian Teak wood as per drawing |
| 33 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type (BWP), core of block board construction with frame of 1 st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters - 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 34 | Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type (BWP), core of block board construction with frame of 1 st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. - 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws |
| 35 | Extra for providing vision panel not exceeding 0.1 sq.m. in all types of flush doors (cost of glass included). Rectangular or square Unit: SQ.M. door area |
| 36 | Providing and fixing second class Indian Teak wood moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surfaces etc. - 50 x 12 mm |
| 37 | Providing and fixing MS grill of required pattern in wooden frames of windows, masonry etc with MS flats, square or round bars with round headed bolts and nuts or by screws - Plain grill |
| 38 | Providing and fixing SS 304 Tower bolts (Barrel type) with necessary screws etc complete - 250x10 mm |
| 39 | Providing and fixing SS 304 Tower bolts (Barrel type) with necessary screws etc complete - 100x10 mm |
| 40 | Providing and fixing bright finished SS 304 handles with necessary screws etc complete - 125mm |
| 41 | Providing and fixing bright finished SS 304 door latch with necessary screws etc complete - 250 x 16 x 5 mm |
| 42 | Providing & fixing Stainless Steel tubular lever D-Type mortise handles with round/Square nose, 24mm Mortise/sash lock body & Strike plate (all SS Finish), Pin cylinder 60mm with one side key and other side knob/thumb turn with necessary screws etc. complete |
| 43 | Providing and fixing 150 mm. SS 304 floor door stopper with rubber cushion screws etc. to suit shutter thickness complete. |
| 44 | Providing and fixing C. P. Brass/brass hydraulic door closer of approved make with necessary screws and fittings complete. |
| 45 | Providing & fixing Stainless Steel Cylindrical lock 60mm dia with pair of knob, keys etc. with necessary screws etc. for doors complete as approved by engineer. Entrance Function: Internal Push Button & External Key Operation |
| 46 | Providing and fixing Stainless steel D type handles with necessary screws etc complete a) L 300mm/325mm x 22 to 25mm dia |
| 47 | Providing and fixing 1.00mm high pressure decorative Laminates (glossy/ matt) on wooden surfaces like doors, windows. The laminate should comprise of layers of specially selected paper, impregnated with melamine and phenolic resins pressed and hardened under heat and high pressure and should ensure strong bonding, resistance to boiling water and chemical and increase dimensional stablilty. Including cost of adhesive, nails during fixing etc. complete |
| 48 | Providing and fixing carbon steel galvanised (minimum coating 5 micron) dash fastner of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter sunk head, comprising of 10 m dia polyamide PA6 grade sleeve, including drilling of hole in frame, concrete/ masonry, etc. as per direction of Engineer. - 10 x 120mm |
| 49 | Providing bright finished stainless steel parliamentary hinges 100x100x27mmx5mm with necessary screws etc complete instead of providing Stainless steel Butt Hinges 100x60x2.5 (Only difference in rate to be quoted) |
| 50 | Providing and fixing SS 304 Aldrop/ sliding door bolts with bolts, nuts and screws etc complete - 250 x 16 mm |
| 51 | Providing & fixing bright finished C. P. Brass/brass 100 mm. rim latch & lock & a pair of knob, with necessary screws etc. complete (Indian make of approved quality). |
| 52 | 5 STEEL AND ALUMINIUM WORKSSteel work in built up tubular (round, square or rectangular hollow tubes etc.) (Square Hollow Section (SHS) IS4923 /Rectangular Hollow Section (RHS) IS4923/ Circular Hollow Section (CHS) IS1161 closed Structural Steel of approved make (Min Yeild Stress 310 Mpa)) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. |
| 53 | Steel work welded (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only) in built up sections trusses and framed work including cutting, hoisting, fixing in position and applying priming coat of red lead paint. - In R.S. Joists |
| 54 | Steel work welded (SAIL, TATA. VIZAG & using electrodes of Ador or ES4B or Deh Secheron make only) in built up sections trusses and framed work including cutting, hoisting, fixing in position and applying priming coat of red lead paint. - In Tees, angles, flats and channels |
| 55 | Providing and Fixing M. S. round holding down bolts with nuts and washer plates complete. |
| 56 | Providing & fixing bolts with nuts & washer complete. (Hi Tensile black bolts & nuts as per approved make) |
| 57 | Providing and fixing stainless steel (Grade 304) railing made of Hollow tubes, channels, plates etc.with hairline finish, including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer, ( for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.). |
| 58 | Designing, Fabricating, Supplying and fixing of structural glazing (SEMI UNITISED SYSTEM) by using JINDAL or Equivalent Extruded Aluminium Sections as following, 22739 of size 131 X 38.5 X 2 mm as outer, 22843 of size 131 X 67 X 2 mm mullion & transom, 22841 of size 66.8 X 28 x 1.6 mm as sub frame. The Glazing will be SINGLE GLAZED UNIT Comprising 6 mm toughened ST 167 Glass of Saint Gobain / Equivalent make having properties as visible Light transmittance (VLT) of 65 to 69 %, Light reflection internal 15 to 20%, light reflection external 10 to 20%, shading coefficient (0.75- 0.82) and U value of 5.0 to 6.3W/m2 degree K etc. complete with transoms and mullions spaced appropriately to form grids, spacer tapes and Dow/ Wacker brand structural and weather sealants at site stuck to the Aluminium profile Surface using spacer tape, a structural bite of 15 mm is given in between glass panes and aluminium frames which is filled with Structural Silicone and finished with backer rod and weather sealant for water resistance. Aluminium members shall be Powder coated (PVDF) to minimum thickness of 50 microns as in colour as instructed by Engineer in Charge. |
| 59 | Ultra-high strength, high-precision, dual shrinkage compensated, free flow cementitious grout for machine , column base plates. Providing and Supplying Masterflow 928T of BASF make or equivalent approved which is dual shrinkage-compensated, cementitious grout shall be hydraulic-cement based free-flow, high strength grout that complies with ASTM C1107. The grout shall have compressive strength minimum of 35 MPa at 1 day and 75 MPa at 28 days; flexure strength minimum of 9 MPa at 28 days. The grout must exhibit positive volumetric expansion in plastic stage as well as hardening stage. Grout must be flowable at 0.15 w/c ratio and shall have fresh wet density in excess of 2200 Kg/m3. The grout must be accredited by reputed testing institute for dynamic load resistance test of 2 million cycles with no sign of cracking or strength loss. All scaffolding, ladders, supporting materials etc. complete. Rates shall be inclusive of all labour, materials, tools and plant etc. complete. |
| 60 | Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer (Door handle, lock and stopper etc.to be paid separately) |
| 61 | Providing and fixing special quality SS 304 Centre patch lock with cylinder for 12mm frameless toughened glass door shutter. The lock should have locking arrangements with keys on both side with necessary screws etc complete |
| 62 | Note;- Refer details at Annexure - IProviding & fixing Anodised Aluminium shutters in accordance with the specifications annexed with including all taxes, transportation, scaffolding and handling etc Complete as per direction of the engineer : Windows with two sliding shutters using 18mm series shutters sections with plain glass including powder coating with pure polyester of required shade and colour. All work between civil work and aluminium frames shall be sealed and made watertight by applying silicone sealant. 4 mm thk clear float glass, EPDM gaskets complete with accessories for locking, handles, stoppers, ball bearing etc. |
| 63 | Note;- Refer details at Annexure -IProviding & fixing Anodised Aluminium shutters in accordance with the specifications annexed with including all taxes, transportation, scaffolding and handling etc Complete as per direction of the engineer : Windows with three sliding shutters using 18mm series shutters sections with plain glass including powder coating with pure polyester of required shade and colour. All work between civil work and aluminium frames shall be sealed and made watertight by applying silicone sealant. 4 mm thk clear float glass, EPDM gaskets complete with accessories for locking, handles, stopppers, ball bearing etc. |
| 64 | Note;- Refer details at Annexure - IProviding and fixing Anodized Aluminium shutters in accordance with the specification annexed with II including all taxes, transportation, scaffolding and handling etc. complete as per direction of the Engineer : adjustable louvred windows (louvre blades of thickness 1.20mm) with figured glass including powder coating with pure polyester of required shade and colour. All work between civil work and aluminium frames shall be sealed and made watertight by applying silicone sealant. 4 mm thk figured glass, EPDM gaskets complete with accessories for locking, handles, stopppers etc. |
| 65 | Supplying and fixing rolling shutters of approved make, made of 80 x 1.25 mm G.M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5cm long wire springs grade No.2 and G.M.S. top cover of 1.25mm thick for folling shutterstop cover and spring. |
| 66 | Providing and fixing Ball bearings for rolling shutters |
| 67 | Extra for providing mechanical device, chain and crank operation for operating rolling shutters. a)Exceeding 16.80 sq.m. in area Chain & overhead operation |
| 68 | Supply & Fixing of Aluminium Plain Exterior Ventilated Facade of approved wood colour consisting of liniar roll formed aluminium panel 84 mm wide x 16 mm deep x 0.6 mm thick with round edges panel length upto 6 meter coil coated on a continuous paint line double baked and roll formed from enameled corrosion Resistance Aluminum Alloy AA3005 / AA5050 (Al.Mn.) for higher strength and good Roll forming characteristics. Panels shall be clipped at a distance of 146mm with a gap of 60mm between two panels to baked enameled Aluminium panel stringer 33mm wide and 48mm deep x 0.95 mm thick in a standard length of 5mtrs made of double baked enameled Aluminium Alloy AA5050 (Al.Mg.) white/black to hold the panel in a module of 146mm centre to centre. The prongs on stringers shall be to accommodate a gap of 60 mm between two panels as per enclosed profile details. Stringers shall be fixed at 150 mm from panel ends and at a distance of maximum 900 mm center to center across the panel span based on the wind load criteria. The Stringer shall be fixed to a suitable structure by means of rigid fixing details. All properties and specifications shall comply with ECCA directives and more specifically EN 1396:1996. Paint Finish: Panel shall be stove enamelled and finished with standard wood color, a special three layered coating system (consisting of first a conversion layer of thickness 800-2000mg/sqmtr, a polyurethane basecoat of 16-20 microns, and a special top coat of polyamide particles of 8-12 microns thick to provide excellent abrasion and damage resistance) in a continuous coil coating process of the approved colour on the exposed side and the reverse side with epoxy. Complete including Wall, corner profiles as per manufacturers’ specifications etc. (including MS Substructure, Rate to include all ridge, eaves, valley & joints flashing, verge & junction trims, facia, etc. of similar finish, making cut-outs for light fittings, diffusers, columns, etc. as required, complete as per approved shop drawings and as directed/ approved by Engineer.) |
| 69 | Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer. (The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). |
| 70 | Supply and installation of 6mm thick Exterior grade F- Quality panels of standard size of one of the following: 1.3 x 2.8 m /1.854 x 2.8 m / 1.3 x 4.1 m / 1.854 x 4.1 m, with both side décor of FunderMax make or equivalent .The panels must be duromer high-pressure laminates (HPL) as per EN 438-6 type EDF with norm conformity as per EN 438-7 manufactured using NT Technology (Non-fading high performance acrylic polyurethane surface technology) conforming to norms with CE Mark. Panels are double hardened including acrylic polyurethane resin which is thermally cured under high pressure. The panel should have passed salt spray test for 24 hours, possess performance sustainability certificate for more than 25 years and proof of experience in handling similar type of work in India for more than 10 years. Material should be class B / class 1 complying with NBC 2016, ASTM E 84, BS 476 - 7. Installation of these panels must be done by MBE Rivets(with Fixed and Sliding Points) with minimum recommended Aluminum T section of 75x37x2 mm thick and L section 40x37x2.8mm thick held by Wall Bracket with Wind load and Dead load slot as per design, anchored by standard Hilti/Fischer or equivalent make anchor fasteners along with Thermal Separator.Installation of the HPL Panels will be done using Rear Ventilated Principles only which is ensured by providing gaps of 20 mm at top and bottom(for free flow of air behind the façade) for the façade and using the framework with no horizontal section. Rate shall include supply of Main exterior panels, Aluminum MBE rivets,supply of Aluminum Substructure (bracket, sections), installation charges, wastages, scaffolding, fabrication. |
| 71 | 6 FLOORING AND FLOOR FINISHESProving & laying 25mm Cement concrete flooring 1:2:4 (1cement :2coarse sand:4 graded stone aggregate 12.5mm nominal size) finished with a floating coat of neat cement |
| 72 | Providing and laying antiskid floor tiles 12 x 12 upto 16 x 16 in of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) of 1st quality conforming to IS:15622 of approved make in shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including pointing the joints with white cement and matching pigment etc., complete - Light Shades (Quality of tile to be conforming to the price range between Rs. 375-450 per sq. mt exluding taxes) |
| 73 | Providing & laying 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacture of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-charge in skirting, risers of steps and dados jointing with cement based high polymer modified quick-set tile adhesive (water based) conforming to IS:15477, using 5 kg. adhesive per sq.m of tile area, in average 3 mm thickness, including pointing in white cement mixed with pigment of matching shade complete. - Wall Ceramic Glazed Tiles : 300 x 600 (Quality of tile to be conforming to the price range between Rs. 400-550 per sq. mt exluding taxes) |
| 74 | Kotah stone slab flooring over 20 mm (average) thick base laid over & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & complete with base of cement mortar 1:4 (1 cement : 4 coarse sand) - 20 mm thick.(Quality of tile to be conforming to the price range between Rs. 560-650 per sq. m exluding taxes) |
| 75 | Proving & laying Kotah stone slab flooring over 25 mm thick in risers of steps, skirtings, dado & pillars laid on12mm (average) thick cement mortor 1:3 (1 cement : 3 coarse sand) & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & polishing complete. (Quality of tile to be conforming to the price range between Rs. 560-650 per sq. mt exluding taxes) |
| 76 | Rounding of edges of marble/ Granite / Kotah slab to semi circular slope |
| 77 | Providing and laying factory made Shot blasted cement concrete interlocking paver block of minimum M35/M40 grade made by heavy duty block making machine with strong vibratory compaction and of aprpoved size and design / shape laid in 50 mm thick compacted bed of coarse sand, filling the joints with coarse sand, etc. all complete as per the direction of Engineer.- in I, Wave, Rectangular, Square etc. shapes. The products should comply to IS 15658:2006 and manfucatured by ISO9001: 2008 certified plant. The shot blasting should be done using 0.4-0.5mm dia steel shots with a speed of 3200 rpm. 60 mm thick in all colours except grey (M35 grade) (Quality of tile to be conforming to the price range between Rs. 735-850 per sq. mt exluding taxes) |
| 78 | Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade, area of slab over 0.50 sqm - Jet Black (Quality of stone to be conforming to the price range between Rs.1883-2000 per sq. m exluding taxes) |
| 79 | Providing and laying jet black mirror polish granite flooring and dado over 20mm thick base of cement mortar 1:4 laid over and jointed with cement slurry including rubbling complete Granitic slab (jet black with mirror polish) 20 mm thick add q0% wastage 1.00 (Quality of stone to be conforming to the price range between Rs.1883-2000 per sq. mt exluding taxes) |
| 80 | Providing and fixing rubbed stone slab table, edges rounded and polished, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer in-charge and finished smooth. - Jet black mirror polish 18mm thick. One side polished and joined together with two component epoxy adhesive to make 18+18mm = 36mm thk partition (Quality of stone to be conforming to the price range between Rs.1883-2000 per sq. mt) |
| 81 | Providing and laying 20mm thick cuddapah in shelves over 20 mm thick base of cement mortar 1:3 complete (Quality of tile to be conforming to the price range between Rs. 377-475 per sq. mt) |
| 82 | Providing and laying 20mm thick cuddapah in shelves complete |
| 83 | Providing & laying 25 mm thick cuddapah slabs machine cut and polished on either side in partitions including making necessary grooves in the wall and fixing with cement mortar, complete as directed by the engineer( Quality of tile to be conforming to the price range between Rs. 377-475 per sq. mt) |
| 84 | Providing and laying vitrified industrial floor tiles in different sizes of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete - 300 x 300 mm Light Shades - 10 mm thickQuality of tile to be conforming to the price range between Rs. 708-750 per sq. mt) |
| 85 | Providing and fixing Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps and dados, jointing with cement based high polymer modified quick-set tile adhesive (water based) conforming to IS:15477, using 5 kg. adhesive per sq.m of tile area, in average 3 mm thickness, including pointing/grouting in white cement mixed with pigment of matching shade complete. - 600x600 mm - light Shades (Quality of tile to be conforming to the price range between Rs. 400-550 per sq. mt exluding taxes) |
| 86 | Providing and laying vitrified floor in different sizes of (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete. - 600 x 600 mm light Shades (Quality of tile to be conforming to the price range between Rs. 400-550 per sq. mt exluding taxes) |
| 87 | Providing and fixing Granite stone slabs (mirror polished) 18mm thick in risers of steps, skirting, dado and pillars laid on cement paste and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete-Elite Brown (Quality of stone to be conforming to the price range between Rs.1291-1400 per sq. mt exluding taxes) |
| 88 | Providing and and laying vitrified unglazed porcelain tactile floor tiles in different sizes of Johnson, Somany, Kajaria (thickness to be specified by the manufacturer) and conforming to IS:15622 of approved make in colours and shades as specified laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand) including grouting the joints with white cement and matching pigment etc., complete - 300x300 Design - Liner/ Button(Quality of tile to be conforming to the price range between Rs. 440-550 per sq. mt exluding taxes) |
| 89 | Vaccum dewatering of laid concrete for roads/ areas using Tremix machinery including formwork with MS channel/ angle sections on sides of concrete with proper supporting system, surface/screed & needle vibrating & levelling of concrete. Vaccum dewatering should be done using suction mats (spread on surface) & suction pump, power floating/ troweling using screen floater, manual spreading of hardening compound (if any), smooth/rough/broom finish to the required slope, camber & level, groove cutting (upto 10mm wide x50mm deep) for contraction/expansion, construction & longitudinal hoints, Providing dowel bars with sleeve/tie bars, filling two component polysuphide sealant/joint filler (Bitumen hot sealing compound: Grade A), taping with masking tape etc complete. (Concrete, reinforcement, Dowel Bar with sleeve/tie bar Reinforcement, tarpaulin sheet to be paid separately) |
| 90 | 7 ROOFING AND CEILING WORKSProviding water proofing treatment over the new RCC roofs, terrace, sunken slabs, chajjas by spreading cement slurry over the RCC slab and laying of 100 mm average laterite stone ballast coba with the necessary gradient for easy flow of rain water and the coba should be covered with damp proof, joint less water proofing plaster of mix 1:3 (1 cement : 3 Fine sand), finish smooth with wooden trowel with false marking of 30cm squares. the Vertical surfaces of the adjoining walls are to be treated upto a height of 30cms including rounding of junctions (The rate includes for complete items including labour and materials and including the cost of initial treatment of roof slab as follows. The injection of damp proof or equivalent compound with cement solution will be given as and when found necessary for filling honey comb cracks etc. in the RCC slabs) Note: The cement consumption 25 kg /sq.m. |
| 91 | An Elastomeric, Cementitious, Waterproofing coat for concrete and masonry. Providing and applying on a well prepared vertical surface Masterseal 550EL of BASF make or equivalent elastomeric flexible, two component polymers modified cementitious composite system that requires no addition of water at the site. The product shall be applied in minimum two coats to achieve total DFT of 1mm. The material shall be mixed and applied fully in accordance with the manufacturer's instructions. The product shall exhibit at least 40% elongation at ambient & 30% elongation in under water condition with tensile strength greater then 20 Kg/cm2. The product shall resist 1.5 bars pressure when tested as per DIN 1048 at 2mm DFT. When applied at 2mm DFT, elastomeric coating shall be able to bridge crack up to 0.5mm width. All scaffolding, ladders, supporting materials etc. complete. Rates shall be inclusive of all labour, materials, tools and plant etc. complete. |
| 92 | Providing and fixing tiled false ceiling of approved materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections (galvanized @ 120 grams/ sqm, both side inclusive) consisting of main \\"T\\" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross \\"T\\" of size 24/15x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main \\"T\\" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross \\"T\\" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main \\"T\\" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25/15 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24/15 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer. - GI Metal Ceiling Lay in plain Tegular/ Bevelled edge Global white color tiles of size 595x595 mm, and 0.4-0.5 mm thick with 8 mm drop; made of G I sheet having galvanizing of 100 gms/sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending. |
| 93 | Providing and Fixing M/F suspended ceiling (Single Layer) which includes providing & fixing GI perimeter channels of size 0.55mm thk having one flange of 20mm and another flange of 30mm and a web of 27mm along with perimeter of ceiling, screw fixed to brickwall/partition with the help of nylon sleeves and screws, at 610mm centres. Then suspending GI intermediate channels of size 45mm, 0.9mm thk with two flanges of 15mm each from the soffit at 1220mm centres with ceiling angle of width 25mmx10mmx0.55mm fixed to soffit with GI cleat and steel expansion fastners. Ceiling section of 0.55mm thickness having knurled web of 51.5mm and two flanges of 26mm each with lips of 10.5mm are then fixed to the intermediate channel with the help of connecting clips and in direction perpendicular to the intermediate channel at 457 mm centres. 8mm tapered edge Calcium Silicate Board is then screw fixed to ceiling section with 25mm drywall screws at 230mm centres. Screw fixing is done mechanically either with screw driver or drilling machine with suitable attachment. Finally the boards are to be jointed and finished so as to have a flush look which includes filling and finishing the tapered and square edges of the boards with jointing compound, Joint paper tape and 2 coats of Drywall topcoat Suitable for Calcium Silicate board, complete in all respects. |
| 94 | Providing and fixing colour coated galvulium roofing sheets of 0.5mm thickness including all the accessories (TATA make) but excluding the cost of purlins, rafters, trusses, flashings etc. complete as per the directions of the Engineer in charge. |
| 95 | Providing & fixing in position Galvalume/Zincalume flashings, cappings, ridges, gutters upto 600mm/610mm girth and min 3.00m in length (cold Rolled Steel 550 MPa yeild Stress ASTM A 446 Grade E) with hot-dip metallic coating of aluminium-zinc alloy(AZ 150 galvalume) (150 gms/sqm total of both sides with Al-Zn Composition= 55% & 43.5% resp. & 1.5% Si conforming to ASTM 792/ AS 1397) 0.45 mm base metal thickness and 0.50mm total coated thickness, factory cut at all heights for roof, side & gable cladding complete in all respects with AZ 150 GSM SMP color Coated (20mic exterior coat of Silicon Modified Polyester paint system over 5 mic primer and 5 mic polyester back coat over 5 mic primer) incl. fixing to purlins with no 12x14x55mm mechanically galvanised hex head self drilling screws of the best quality as per AS-3566 class 3-4 approved, which should be compatible to be used with sheets. with integral washers and EPDM seals etc. Silicon sealant non-hardening neutral cure type shall be applied at all end laps, complete as directed. |
| 96 | Providing & Fixing in position Double Skin roof with Zincalume/ Galvalume colour coated & bare profile sheet with subtle square fluting factory cut at all heights for roof, side & Gable cladding complete in all respect. TOP SHEET-The end rib shall be designed for anti-capillary action. The feed material should be manufactured out of nominal 0.45 mm Base Metal Thickness (BMT), Hi-strength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 43.5% Zinc &1.5% Si) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides) with quality paint coat as per AS/NZS 2728 type 3-4. The paint shall have a total coating thickness of nominal 35 μm, comprising of nominal 20 μm exterior SMP coat on top surface and nominal 5 μm reverse backer coat on back surface over nominal 5 μm primer coat on both surfaces of approved colour shade. Total Coated Thickness (TCT) should be 0.50mm. Total Painted Thickness (TPT) should be in addition to 0.50mm. The steel sheet shall be fastened with nominal 40 μm zinc coated or nominal 25 μm zinc-tin alloy coated, Hex head, self-drilling screw as per AS 3566-2002 Class 3 fasteners of approved make with EPDM washer as per the requirement considering the profile shape and design load. The fastener size shall be calculated as per the design or manufacturers recommendations. The profile sheet, fastener size etc. shall be approved by the Engineer. The sheeting should be with minimum 200mm lap & waterproof with Silicon sealant non-hardening neutral cure type shall be applied at all end laps, complete as directed Z-Sub Girt - roll formed section 50x50x50x1.50 TCT, 120GSM Galvanised, High Strength (345 MPa), approximate Wt. 1.85 kg/r.m. fixed with self tapping screws Glass Wool Insulation with FSK facing 50mm with 24 kg/m3 density in between 2 sheets. LINER SHEET-bare galvalume/zincalume roofing sheet of same profile as top sheet. The feed material is of manufactured out of nominal 0.45 mm Base Metal Thickness (BMT) (0.47 mm TCT), Hi-strength steel with min. 550 MPa yield strength, metallic hot dip coated with Aluminium-Zinc alloy (55% Aluminium, 45% Zinc) as per AS 1397 - Zincalume AZ150 (Min. 150 gms/sq.mt total on both sides), passivated & resin coated. The feed material should have coil manufacturer’s product details marked at regular interval for confirming genuinity of the material. complete as per the directions of the engineer. The steel manufacturer's test certificate for the chemical & mechanical properties of steel must be submitted for approval prior to installation. |
| 97 | Providing and laying integral cement based treatment (Box type) for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer and consisting of : i) Ist layer of 20 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound. ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer using rough Shahbad/Kotah stone. |
| 98 | Providing and laying integral cement based treatment (Box type) for water proofing on the vertical surface by fixing specified stone slab 20 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer using rough Shahbad/Kotah stone. |
| 99 | 8 PLASTERING AND FINISHING WORKS12mm cement plaster of mix 1:4 (1cement: 4 fine sand) |
| 100 | 6mm cement plaster of mix 1:3 (1 cement : 3 fine sand) |
| 101 | neat cement punning |
| 102 | Extra for providing and mixing water proofing material proportion recommended by the manufacturers. a) 12mm cement plaster 1:4 (1 cement : 4 sand) |
| 103 | 18mm cement plaster in two coats under layer 12mm thick cement plaster 1:5 ( 1 cement : 5 coarse sand) and top layer 6mm thick with cement plaster 1: 3 (1 cement : 3 coarse sand) finished with sponge including providing and mixing water proofing material proportion recommended by the manufacturers. |
| 104 | 12mm thick plain cement mortar bands in cement mortar 1:4 (1 cement : 4 fine sand) a) raised band |
| 105 | White washing with lime on new work (three or more coats) to give an even shade including minimum one priming coat |
| 106 | Applying priming coat with ready mixed primer of approved brand and manufacture on wood work complete. |
| 107 | Applying priming coat with ready mixed primer of approved brand and manufacture on steel work. |
| 108 | Painting two or more coats (excluding priming coat) with superior quality ready mixed paint for wood work of approved brand & manufacture in all shades on new work to give an even shade. |
| 109 | Painting two or more coats (excluding priming coat ) with superior quality ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give a even shade |
| 110 | Painting three or more coats with acryllic exterior paint of approved brand and manufacture (such as Dulex/ Asian Paints/ Sherwin Willians) including applying one coat of cement primer and one coat of surface treatment etc. complete, At all heights from ground level |
| 111 | Painting(two or more coats) with synthetic enamel paint of approved brand and manufacture in all shades on new work over and under coat of suitable shade with ordinary paint of approved brand and manufacture to give an even shade |
| 112 | Wall painting (two or more coats) with plastic emulsion paint of approved brand and manufacture on new work to give an even shade (including min two priming coats and two layers of putty alternatively) |
| 113 | Varnishing (two or more coats) with copal varnish of approved brand and manufacture on new work including an under coat Bees waxing on wood work with local made wax polish in proportion of 2:1 5:1 0.5 (2 wax: 1.5 linseed oil - With transparent wood filler. |
| 114 | Providing and applying white cement based putty of average thickness 1.00mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. |
| 115 | Painting (one or more coats) with black japan paint of approved brand and manufacture to give an even shade. |
| 116 | Melamine polishing on wood work (one or more coat) - Matt |
| 117 | 9 LANDSCAPING AND HORTICULTURE WORKSPlanting of trees by the roadside (Avenue trees) in 0.60 m dia holes, 1 m deep dug in the ground mixing the soil with decayed farmyard/sludge manure, planting the saplings, backfilling the trench, watering, fixing the tree guard and maintaining the plants for one year as per MORTH Specification 307 |
| 118 | Supplying and stacking of good earth at site including royalty and carriage upto 1km (earth measured in stacks will be reduced by 20% for payment) including Spreading of Sludge Farm Yard Manure or/and good Earth (Spreading of sludge farm yard manure or/ and good earth in required thickness (cost of sludge, farmyard manure or/and good earth to be paid for separately) |
| 119 | Turfing lawns with fine grassing including ploughning, dressing including breaking of clods, removal of rubbish, dressing and supplying doob grass roots at 10 cm apart including supplying and spreading of farmyard manure at rate of 0.6 cum per 100 sqm as per MORT&H Specification 307 including Maintenance of lawns with fine grassing for three years including watering, etc.as per MORTH Specification 307 |
| 120 | Planting permanent hedges including digging of trenches, 60 cm wide and 45 cm deep, refilling the excavated earth mixed with farmyard manure, supplied at the rate of 4.65 cum per 100 metre and supplying and planting hedge plants at 30 cm apart as per MORT & H Specification 307 including maintenance of hedge for three years including watering etc. |
| 121 | Supply at site of work well decayed farmyard manure, from any available source approved by the engineer including screening and stacking as per MORT & H Specification 308.2 including Spreading of sludge farm yard manure in required thickness as per MORT & H Specification 307 |
| 122 | 10 ROAD WORKSProviding and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand ) including testing of joints, etc. complete.- a) 100 mm dia RCC pipe |
| 123 | Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand ) including testing of joints, etc. complete.- a) 250 mm dia RCC pipe |
| 124 | 11 WATER SUPPLY, SEWERAGE, PLUMBING AND SANITATION WORKSProviding and fixing Rigid PVC (SELFIT) pipes for public water supply including Railway freight, carting, loading and unloading, stacking, transit insurance etc, conforming to ASTM 2467 with ISO 14001, including all PVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of Engineer.conforming to IS 4985-2000 and bearing ISI mark, CLASS 6 KG/ SQ. CM a) Outer dia 63 mm |
| 125 | b) 75 mm |
| 126 | c) 110 mm |
| 127 | d) 140 mm |
| 128 | Proving and fixing white vitreous china extended Wall Hung type (European Type) water closet of approved shape with seat and lid with C.I. brass hinges and rubber fittings with white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/6 litre (adjustable to 4 litre/ 8 litre), etc. including chair bracket/rag bolts, cutting & making good the walls and floors where required and concealed seat support - W.C. Pan with white plastic seat and lid |
| 129 | Providing and fixing white vitreous china flat back Large lipped front urinal basin of 590x375x390mm size with Urinal Valve Auto closing system with built in control cock & wall flange with fittings, spreader, R.S. or C.I. brackets, standard size C.P. Brassl flush pipe and spreaders with C. P. brass unions & C. P. Brass clamps with waste fitting as per IS 2556, PVC trap with outlet grating and other couplings in CP Brass complete, including painting, fittings, cutting and making good the walls and floors where required. - Range of one urinal basin |
| 130 | Providing and fixing vitreous china under counter wash basin with RS or C.I. brackets painted white, NICKEL chrome plated copper alloy Fancy Pillar Cock rocket type Jaquar make or equivalent. Confirming to IS 8931;1993, 32 mm C.P. brass waste of pattern, 32 mm diameter M.I. Or C.P. brass trap and union complete, including cutting and making good the walls where required. - wash basin 550x400/Oval 560x410mm/ round 550x450mm |
| 131 | Providing & fixing bevelled edge mirror of superior glass (5mm thk) of approved Quality, shape & size complete with CP brass screws and washers, Cleats, CP studs etc Complete |
| 132 | Providing & fixing C.P. Brass towel rail complete with C.P. brass brackets fixed to wooden cleats with C.P. Brass Screws - 600x20mm size |
| 133 | Providing and fixing toilet paper holder - C.P. brass |
| 134 | Providing & fixing soap dish chromium plated with brackets fixed to wooden cleats with CP brass screw |
| 135 | Providing and fixing brass stop cock (heavy) of approved quality - 20mm nominal bore |
| 136 | 25mm nominal bore |
| 137 | 32mm nominal bore |
| 138 | 40mm nominal bore |
| 139 | 50mm nominal bore |
| 140 | Providing and fixing brass full way valve (heavy duty) with wheel of approved quality - 20mm nominal bore |
| 141 | 25mm nominal bore |
| 142 | 40mm nominal bore |
| 143 | 50mm nominal bore |
| 144 | Providing and fixing ball valve (brass) of approved quality High pressure with P.V.C. floats - 20mm nominal bore |
| 145 | Providing and fixing square-mouth S.W. gully trap grade ‘A’ complete with C.I grating brick masonry chamber and water tight C.I. cover with frame of 300 x 300 mm size (inside the weight of cover to be not less than 4.53 kg). And frame to be not less than 2.72 kg as per standard design - 150 x 100 mm size – P or S type |
| 146 | Constructing brick masonry manholes or inspection chamber with second class bricks in cement mortar 1:5 (1 Cement : 5 Fine Sand), RCC top slab 1:1.5:3 mix (1 Cement :1.5 Coarse Sand : 3 graded stone aggregate 20mm nominal size) Foundation concrete 1:1.5:3 (1 Cement :1.5 Coarse Sand : 3 graded stone aggregate 20mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 Cement : 3 Coarse Sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4mix (1 Cement :2 Coarse Sand : 4 graded stone aggregate 20mm nominal size) neatly finished complete as per standard design. a) Inside size 90x80 cm and 60 cm deep including Supplying and fixing at the site of work of Steel Fibre Reinforced Concrete (SFRC) manhole covers with frames made as per IS :12592 (part I and II) - 1991 in concrete M45grade. The covers and lapped in 2mm thick. steel plate and this plate & lifting hooks are duly painted in corrosion resistant epoxy paint etc. complete. Light Duty (2.50 Metric Tonne Capacity) a) 450x900 |
| 147 | Constructing brick masonry manholes or inspection chamber with second class bricks in cement mortar 1:5 (1 Cement : 5 Fine Sand), RCC top slab 1:1.5:3 mix (1 Cement :1.5 Coarse Sand : 3 graded stone aggregate 20mm nominal size) Foundation concrete 1:1.5:3 (1 Cement :1.5 Coarse Sand : 3 graded stone aggregate 20mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 Cement : 3 Coarse Sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4mix (1 Cement :2 Coarse Sand : 4 graded stone aggregate 20mm nominal size) neatly finished complete as per standard design. b) Inside size 60x60 cm and 60 cm deep including Supplying and fixing at the site of work of Steel Fibre Reinforced Concrete (SFRC) manhole covers with frames made as per IS :12592 (part I and II) - 1991 in concrete M45grade. The covers and lapped in 2mm thick. steel plate and this plate & lifting hooks are duly painted in corrosion resistant epoxy paint etc. complete. Light Duty (2.50 Metric Tonne Capacity) b) 450x600 |
| 148 | Providing & fixing rigid PVC SWR (soil, waste and rain water drainage pipes of approved make including lubricant etc. complete ( single/double socketed) - 110 mm dia |
| 149 | 75 mm dia |
| 150 | Providing & fixing rigid PVC bend (approved make) for SWR pipes including lubricating etc. complete bend with door - 110 mm dia |
| 151 | 75 mm dia |
| 152 | Providing & fixing single Tee of rigid PVC (approved make) for SWR pipes including lubricating etc. complete bend with door - 110 mm dia |
| 153 | 75 mm dia |
| 154 | Providing and fixing single “Y” of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with door - 110 mm dia |
| 155 | 75 mm dia |
| 156 | Providing and fixing double “Y” of rigid PVC (approved make ) for S.W.R. pipes including lubricating etc complete, with door - 110 mm dia |
| 157 | 75 mm dia |
| 158 | Providing & fixing Nahani trap of rigid PVC of (approved make) for SWR pipes including lubricating etc complete with SS door - 75mm dia |
| 159 | Providing & fixing U.P.V.C. pipe clips (approved make) for S.W.R pipe - 110mm |
| 160 | 75mm dia |
| 161 | Providing and fixing NICKEL chrome plated copper alloy Fancy BIB Cock Short Body Jaquar make or equivalent. Confirming to IS 8931;1993 - 15mm nominal bore |
| 162 | Providing and fixing NICKEL chrome plated copper alloy Fancy long body bib cock with wall flance Jaquar make or equivalent. Confirming to IS 8931;1993 - 15mm nominal bore |
| 163 | Providing and fixing NICKEL chrome plated copper alloy Fancy ANGULAR STOP COCK WITH SLINDING FLANCE 15MM Jaquar make or equivalent. Confirming to IS 8931;1993 - 15mm nominal bore |
| 164 | Providing and fixing P.V.C. connection pipe with brass unions 15 mm nominal bore - a) 30 cm (12\\") length |
| 165 | Providing and fixing NICKEL chrome plated copper alloy Fancy CONCEALED STOP COCK WITH sheet flance 20mm Jaquar make or equivalent. Confirming to IS 8931;1993 - 20mm nominal bore |
| 166 | Providing and fixing NICKEL chrome plated copper alloy Fancy wall mixer with 115mm long bend pipe for connection to over head shower Jaquar make or equivalent. Confirming to IS 8931;1993. Wall mixer with 115 mm long bend pipe for connection to over head shower. |
| 167 | Providing and fixing chlorinated ployvinyl chloride (CPVC) pipes confirming to IS:15778, having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipes with clamps at 1 mt. spacing. This includes jointing of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of the Engineer. Concealed work (medium duty SDR 13.5 pipe) including cutting chases and making good the walls etc. - 15 mm dia nominal outer dia pipes. |
| 168 | 20 mm dia nominal outer dia pipes. |
| 169 | 25 mm dia nominal outer dia pipes. |
| 170 | 32 mm dia nominal outer dia pipes. |
| 171 | Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS 13983 including cutting of stone and making good the walls wherever required. Kitchen sink without drain board. with coupling & all accessories complete with choke stop strainer, Plain type having flat borders for correct sandwithing between the plaform top and bottom slabs complete - Overall size 535mmx460mm (21\\"x18\\") bowl size 460mmx380mmx200mm (18\\"x 15\\"x 8\\") depth 200 mm. Glossy. 1.0mm thk, |
| 172 | Providing and fixing C.P. brass shower rose with 15 or 20mm inlet : 150 mm diameter |
| 173 | Providing and fixing Hand Shower (Health Faucet) with 8mm dia, ABS/brass body with double lock 1.00m long Flexible tube (Brass plated stainles steel flexible hose) and wall hook of approved quality confirming to IS standards. |
| 174 | Providing and fixing NICKEL chrome plated copper alloy Fancy Two Way Bib Cock with single knob and wall flange conforming to IS 8931:1993 15mm nominal bore. |
| 175 | Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/Granite/Cuddapah stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete. |
| 176 | Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step UPVC solvent cement and testing of joints complete as per direction of Engineer. Internal work - Exposed on wall. SCH-40 (blue)/(white) - 25mm outer dia. |
| 177 | 32mm outer dia |
| 178 | 40mm outer dia |
| 179 | 50mm outer dia. |
| 180 | Providing and fixing ASTM UPVC pipe, conforming to ASTM 2467 with ISO 14001, including all UPVC plain & brass threaded fittings, including jointing of pipes & fittings with one step UPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer. External work. SCH-40 (blue)/(White) - 20mm outer dia. |
| 181 | 25 mm dia nominal outer dia pipes. |
| 182 | 32 mm dia nominal outer dia pipes. |
| 183 | 40 mm dia nominal outer dia pipes. |
| 184 | 50 mm dia nominal outer dia pipes. |
| 185 | 12 MISCELLANEOUS ITEMSProviding anti termite treatment to the building conforming to IS:6313 (part II) 1971 adopted, including adopting the precautions for health hazards and safety measures as required therein with the cost of all materials, chemicals plants, equipments etc required for the treatment and furnishing a guarantee for a minimum period of 10 years from the date of completion including eradicating any infestation of termite free of cost during the guarantee period complete. The payment will be made on the Plinth of the building) a) Preconstruction |
| 186 | Providing & fixing in position fixed glass for shower partition with 10mm toughened clear glass on patch fittings in SS 316 grade, Reinforcement bar, silicone sealant Complete. |
| 187 | Providing & fixing in position traction matting antiskid clear tape 2 inch wide (50mm) for staircase having Granite Treads. The antiskid clear tape should be mineral coated slip resistant material with pressure sensitive adhesive including cleaning, degreasing, priming to mask the surface (if required), presssing using rubber roller etc. complete |
| 188 | Providing and fixing in position terracotta jallis as per specified size, pattern and colour, all complete. The jalli size of 200-220x200-220x60-63mm with size accuracy of +/-5% and should be suitable for exterior use with less than 6% water absorption capacity. The jalli should be fire resistant, with anti skid and scratch resistant properties. There should be uniformness in colour texture and colour should not fade after exposure to sunlight. The jallis are to be fixed like bricks stacked on each other with adhesives and stiffeners are to be embedded in the jalli to provide strength. The installation process should be as specified by the manufacturer with special tile adhesive approved by the Engineer incharge. Preparation of the surface should be as per manufacturers instructions and specifications. The surface of the jalli has to be cleaned of any residual adhesive soon after installations to give it a clean and neat look. MS plate 40mmx5mm has to be placed at every third layer and welded to MS Hollow section which has to be provided on sides, as per attached drawing. (MS will be paid separately) complete. |
| 189 | Providing and Fixing Aluminium AL CUSTOM PERFORATED FACADE 800 MM X 4000 X 3MM Thick PC RAL 9010 EXT. Single Skin Screen Panel – 3 mm – Custom Perforation – White Colour (PC RAL 9010 – EXT ) – Square / Rectangle perforation – Asymmetric Design -100 mmThe Screen cladding panels of various sizes maximum up to 800 mm X 4000 mm as per the design requirement shall be manufactured from high corrosion resistant Aluminium alloy of 3.0mm thickness which shall be fixed to a suitable and rigid substructure by others Screen panels shall have customized perforation as per consultant design and is to be provided to suite the design Panels. Panels shall be coated on visible side with Exterior Architectural Coating in approved color. The panels of required length and height shall be fixed to sub structure by means of screen panel guide clamps of 20 x 43x 2mm GI. Panels shall be bending from all four sides and shall have extended flanges to accommodate clamps. The Panels shall be fixed to a suitable structure by means of fixing side extrusion fixed to the panel at appropriate centers to metal clamp as per the manufacturer's design to a support system taking into account the relevant live loads and a dead load. There will be a provision for an expansion joint of 20mm between two adjacent panel ends. Installation shall be carried out as per manufacturer recommendation including Anchor fasteners and Nuts & Bolts. Complete including loading/Unloading, transportation, wastages, scafolding etc. (Only MS/AL/GI substructure will be paid separately) |
| 190 | Proving and laying 120 microns waterproof plastic film/sheet as per IS 14611-1998 as a separation/slip membrane laid flat without creases and with minimum overlap of 200mm at joints, nailed to underneath Plain Cement concrete, if required as directed. |
| 191 | Providing & Fixing Signage made of 6mm thick transperent/ coloured acrylic sheet base material. The graphic should be computer cut self adhesive vinyl covered with clear vinyl to protect from peeling. The signage should be fixed with 12mm dia S.S. studs or S. S. Mirror screws. |
| 192 | Providing and fixing signages made from aluminium composite panel 4mm thk. base material with computer cut self adhesive vinyl graphic covered with clear vinyl to protect from peeling. The signage shall be fixed with 12mm dia S.S. studs or S.S. mirror screws. |
| 193 | Providing & Fixing in position Autoglow photoluminescent Signage made of 1.5mm thick Rigid sheet as base material. The colour, text, size graphic symbol should be as specified by the Fire and Safety Department and IS code 12349(1988) (Reaffirmed 2002) . The signages should be approved by the engineer in charge. The signage should be fixed with 12mm dia S.S. studs or S. S. Mirror screws.. |
| 194 | Providing & Fixing Backlit LED (6500k, 2W), double sided Emergency Escape Signages showing directional arrow, text and size as directed by engineer in charge. It should contain powder coated steel/ Aluminium fabricated frame. It should have provision to Hang to ceiling with the help of SS chain at both ends. Operating voltage 230VAC/24VDC/ 12VDC with battery operated.IT should have rechargeable battery with back up time more than 90 minutes. IP20 rating. approx size 300-320x 170-180x35mm. |
| 195 | 13 PILE WORKBoring holes vertically true to line and form for R.C.C. bored piles (Bored cast-in-situ) of required diameter in all strata including removing slush, all kinds of soil and rock (including socketing upto 1-2 times diameter of pile in hard/soft rock), percolating water etc. complete from the above to keep ready for concrete (including the cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and leads) after placing reinforcement but excluding the cost of providing and laying concrete and reinforcement. a) 500mm dia bore upto 32.0m depth from ground (length of pile for payment shall be measured up to bottom of pile cap). All work to be done as per IS 2911 |
| 196 | Providing and laying reinforced cement concrete of grade M 40 (mix design) with coarse sand and graded granitic or basaltic aggregate 20mm nominal size as per mix design requirements in bored cast in situ piles of specified diameter at the required workability and compaction as per the direction of the Engineer-in-charge including all operation for placing the concrete, lifting the casing in stages etc. but excluding the cost of reinforcement. a) 500mm dia pile upto 32.0m depth from G. L. (including welding of reinforcement, lowering reinforcement cage, use of tremie, dressing the excess pile concrete upto to pile cutoff level). All work to be done as per IS 2911 |
| 197 | Cyclic vertical load testing of pile in accordance with IS Code of practice IS: 2911 (part IV) by Kentledge/ Anchor Pile method including preparation of pile head etc for. a) Single pile above 75 tonne and upto 125 tonne capacity |
| 198 | Lateral load testing of single pile in accordance with IS Code of practice IS : 2911 (Part IV) for determining safe allowable lateral load on pile : a) upto 40 tonne capacity pile |
| 199 | Integrity testing of Pile using Low Strain/ Sonic Integrity Test/ Sonic Echo Test method in accordance with IS 14893 including surface preparation of pile top by removing soil, mud, dust & chipping lean concrete lumps etc. and use of computerised equipment and high skill trained personal for conducting the test & submission of results, all complete as per direction of Engineer-in-charge. |
| 200 | High Strain Dynamic Pile Testing on r.c. bored piles using Pile Driving Analyzer. The equipment shall have ability to record both force and velocity. Both strain and acceleration sensors shall be used to collect data & atleast 2 pairs shall be connected at diametrically opposite sides of the pile. The test and equipment shall conform to ASTM D4945-2000 & include CAPWAP analysis. The CAPWAP match quality shall be preferably less than 5. The test shall be conducted by an experienced independent test agency that has demonstrated their capabilities by performing reliability studies in various conditions such as for friction piles, end bearing piles etc. and/or by publishing technical literature through the known forums. The testing agency should have atleast five years experience with testing of bored piles a) above 75 tonne and upto 125 tonne capacity pile |
| 201 | Providing, placing and driving in position 6 mm thick permanent M.S.Liner upto required depth with 12 mm thick M.S. cutting edge of 0.5 metre length of bottom including fabricating, cutting the M.S. sheet to required diametre and shape, welding the joints and driving with the help of required machineries including all materials, labour and lift etc. complete. (length of pile liner for payment shall be measured up to bottom of pile cap) |
| 202 | Providing and applying as per technical specification anticorrosive treatment consisting of 2 coats of coal tar epoxy with one coat of zinc rich epoxy primer (total dry film thickness 50 + 80 + 80 = 210 microns) for foundations, liner of pile and substructure in contact with soil / earth or water. |
| 203 | Providing corrosion resistant steel CRS-50 bars of (SAIL, TATA. VIZAG, JSW Steel Ltd.) (Confirming to IS 1786 if 1985) for RCC work including bending, binding & placing in position in all the floors along with factory made precast concrete cover blocks of specified sizes whose compressive strength is not less than that of surrounding concrete in the structural member . |
| 204 | (Note;- Please refer special condition of Vol -I, Pg no. 63 -64 for detail Item description)Lift WorksSupplying, Installing, Testing and Commissioning (SITC) of Electric Traction Passenger Lift with• Rated capacity :- 8 Passenger/544Kg • Floors :- G+3 floor (4Stops/4 Landings) • Travel :- 9.45 mtrs • Location of Lift Machine:- Machine Room Less (MRL) • Rated speed :- 1.0mps Variable speed (VS) • Car/Landing door clear opening of 800 mm wide x 2000 mm high • Clear Car size of 1100 mm wide x 1300 mm deep x 2250mm high • Lift shaft available having clear size of 1850 mm wide x1650 mm deep, 1600 mm Pit depth, 4100mm Overhead. • Doors type :- Centre Opening Power Operated (COPO)/ Telescopic Opening Power Operated (TOPO) Doors with frame made from SS 304 grade solid (non-cladded) sheet of 1.5mm thick in hairline finish for car and all landing doors with SS door architraves/frames The lift doors shall have minimum 1 hour fire rating (with submission of necessary valid test certificate issued by NABL accredited or Independent test laboratory). • Lift car enclosure made from SS 304 grade solid (non-cladded) sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. The lift car interior design shall be done as per the directions of engineer in charge. • Car Operating Panel (COP) with SS face plate having metallic push buttons with Braille Code & luminous indicator around button with Floor Position Indicator (FPI), scrolling UP/DN LED indicator & with/without attendant key switch, Overload warning Device (OWD) with audio-visual alarm, Voice annunciation system (VAS) in Konkani/Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor.• Landing Operating Panel (LOP) with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille Code & luminous indicator around button with Car Position Indicator (CPI), Lift car arrival & next travel direction audio-visual indication at all landings. • Lift controller based on microprocessor/ Programmable Logic Control (PLC) with Variable Voltage Variable Frequency (VVVF) Drive having closed loop control system, with Intelligent Building Management System (IBMS) compatible having necessary port. The controller shall have necessary protections such as over current, over voltage, over speed, overheat for all devices including lift motor and travel direction protection, protection for phase loss at input or output etc. various operation modes such as maintenance, change direction by attendant, full load bypass, VIP call operation, self levelling operation, call cancel facility, auto return to home landing, fireman evacuation operation, earthquake operation, door open/close operation from COP etc. The system can record information for minimum 30 latest faults, with real-time clock management and handheld keypad with LCD screen for view and setting of parameters. The control panel duly wired with proper size & strength, copper wire for power & control circuit, with provision for addition of floor/control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class. • Automatic Rescue Device (ARD) complete with necessary Sealed maintenance free (SMF) Valve-Regulated Lead-Acid (VRLA) batteries shall be suchthat minimum three consecutive rescue operations can be performed without recharging for the maximum travel distance between two consecutive served stops. ARD have a suitable audio alarm with visual indication or voice annunciation in the lift car or lift controller to indicate“Low battery”. • Fireman controller having fireman switch at fire Landing, • Closed Circuit Television (CCTV) surveillance system comprises of 2 nos minimum 2.0MP FHD IP (Internet Protocol) based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with Network Video Recorder (NVR) kept in LMR/Fire Command Centre (FCC) with High Definition Recording (HDR) data backup for 90 days with 20\\" Full High Definition (FHD) TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge.• Lift Machine of Gearless Permanent Magnet Synchronous AC Machine (PMSM) of suitable kW with duty cycle of minimum 120 starts per hour (with submission of necessary test certificate issued by NABL accredited or Independent test laboratory), with Traction pulley, Over speed safety governor (OSG), electromagnetic brakes, entire assembly mounted on adequate size girders duly fixed on Lift machine room (LMR) floor/ shaft walls complete with main/diverter traction sheaves, suspension wire ropes/belts of adequate size & strength. • Other mechanical parts such as 'T' section adequate size guide rails for car & counter weight with brackets fasteners, counter weight frame with necessary blocks, buffers with necessary support arrangement, MS pit ladder etc. erected with necessary steel work. • Minor civil work such as alteration work if any necessary for erection of landing door frames and its accessories eg. sill, header, hole pass etc complete with plaster finish, civil work for erection buffers, erection of lift machinery, adequate size core cuts if required & scaffolding for erecting guide rails, providing & fixing steel girders/RCC work having adequete strength for mounting & Hosting lift machine etc. complete as per specification no. LFT. Including For Lift having 800mm wide x 2000mm high clear entrance in 1.5mm thick SS 304 grade landing door [Two panel], this includes all necessary accessories like LOP's with UP/DN buttons-arrows indicators, extension of guide rails, shaft wiring with trunking, travelling cables, main hoisting ropes/belts, & OSG rope landing doors with all accessories, door operator mechanism with drive, required aluminium sill, infrared curtain & necessary wiring with interlocking arrangement etc. necessary for the normal safe functioning of lift installation complete. • Full Collective Control System 1) General: - Job includes entire procedure of obtaining all necessary erection permissions & \\"License to Work the Lift\\" from Electrical Inspector(Lifts) with submission to the Engineer In Charge.· The above rate includes Fully Comprehensive AMC for one year from the date of commissioning |
| 205 | 15 ELECTRICAL WORKA : Point WiringWiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit (heavy) with modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (a) Group C -- with Cat B Modular Accessories |
| 206 | Wiring for group controlled light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit (heavy) and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. |
| 207 | Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in recessed PVC conduit(heavy) with 2 way modular switch, modular plates, suitable size modular GI box of specified Category and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required. (a) with Cat B Modular accessories |
| 208 | Supplying and fixing stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required (a) Cat B |
| 209 | Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin 5/6 A modular socket outlet and 5/ 6 A modular switch connection painting etc. as required. - Cat B |
| 210 | Supplying and fixing suitable size modular GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 15/16 A and 5/6 A modular socket outlet modular socket outlet and 15/16 A modular switch connection painting etc. as required. - Cat B |
| 211 | Supplying and fixing modular blanking plate on the existing modular plate switch box excluding modular plate etc. as required - Cat B |
| 212 | Supply and erecting fan hook box (100 mm diameter or equivalent square size, 75mm deep) fabricated out of 16 SWG sheet steel with 10 m round bar hook bounded to RCC steel upto 50 mm length protruding on each side of the box, including painting with 2 coats of red oxide, complete as required. |
| 213 | Supply and erecting 'J' type Mild Steel fan hook fabricated out of 35 X 6 mm flat strip suitable for rafters complete with coach screws etc as required. (a) For 6 inches rafter size |
| 214 | Supplying and erecting ‘B’ grade G.I .pipe / M.S. pipe down rod duly painted for fan complete erected with PVC three core flexible cable 1 sq. mm copper PVC wire. |
| 215 | B : Fixtures, FansSupply and erecting of 9 inch (225 mm sweep) exhaust fan with double ball bearings, 1400 rpm, complete with all accessories. a) Cat A |
| 216 | Supplying and erecting Energy Saving BLDC Ceiling fan 230 V A.C. 50 cycles 1200 mm, max. energy consumption of 28W having service ratio (CMM/W) of Min. 8 , PF>0.9, THD<10% Temperature Rise of Max. 40 deg. C, having external mounted control PCB completely erected in position as per specification no. FG-FN/CF |
| 217 | Providing and erecting air circulator 450 mm. sweep oscillating type, wall mounting 1440 RPM without speed regulator, overheat protection unit, totally enclosed, flame proof motor suitable for230/250 Volts single phase, 50 cycles A.C. supply, with one metre of 3core lead wire and with moisture proof treatment to winding and with ‘E’ class insulation. |
| 218 | Supplying and erecting LED square / circular Max. 18 W down lighter / Panel Light having pressure die-cast aluminium housing, polystyrene diffuser having system lumens output of Min. 2000 Lumens, min. efficacy of 110 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs at L70B0 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG-IDF/LED. |
| 219 | Supplying and erecting anodized aluminium light LED fitting (4 feet) Max. 22W with high transitivity diffuser with system lumens output of Min.2200 lumens , min. efficacy of 100 lumen/W, CRI>80, CCT upto 6000K, Beam Angle of 110 deg., Ripple<5%, THD<20%, p.f. >0.95, operating range of 200-270V, surge protection of 2 kV, Life class of 50,000 Hrs at L70B50 including driver with end caps on provided PVC Block/wooded board with minimum 2 years warranty as per specification No. FG-IDF/LED. |
| 220 | Supplying and fixing brass batten/ angle holder including connections etc as required. |
| 221 | Supplying & erecting 5W-7W, 230V integral type LED Lamp suitable for B-22/E-27 base as per specification no. FG-LP. |
| 222 | Supplying and erecting integrated LED Highbay Fitting 70W IP65 & IK08 class having die cast aluminium housing with polycarbonate diffuser with integrated optics, having system lumens output of Min.10000 Lumens, min. efficacy of 145 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.90, operating range of 140-240V, inbuilt surge protection of 4 kV, Life class of 50,000 Hrs at L50B50, including driver complete with 2 Year warranty as per specification No FG-ODF/LED. |
| 223 | Supplying and erecting LED Panel Light (600mm X 600mm) Max. 35 W having CRCA powder coated housing, polystyrene diffuser having system lumens output of Min 4200 Lumens, min. efficacy of 120 lumen/W, CRI>80, CCT upto 6500K, Beam Angle of 120 deg., max. ripple of 5%, THD<10%, p.f. >0.95, operating range of 120-270V, surge protection of 2.5 kV, Life class of 50,000 Hrs. at L70B50 including driver, having mounting arrangement with board for surface type or spring loaded mounting clips complete with minimum 2 years warranty as per specification No. FG-IDF/LED. |
| 224 | C : Circuit WiringWiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in the independent recessed PVC conduit (heavy) of appropriate size as required.(a) 2 x 2.5 sq.mm + 1 x 2.5 sq.mm earthwire (20mm Conduit) |
| 225 | (b) 2 x 4 sq.mm + 1 x 4 sq.mm earthwire (20mm Conduit) |
| 226 | (c) 2 x 6 sq.mm + 1 x 6 sq.mm earthwire (25mm Conduit) |
| 227 | (d) 4 x 6 sq.mm + 2 x 6 sq.mm earthwire (32mm Conduit) |
| 228 | (e) 4 x 10 sq.mm + 2 x 10 sq.mm earthwire (32mm Conduit) |
| 229 | (f) 4 x 16 sq.mm + 2 x 16 sq.mm earthwire (40mm Conduit) |
| 230 | D : Mcb Distribution Boards & Mcb's & Accessories.Supplying & erecting CRCA sheet metal one way enclosures of 1.2mm thickness suitable for DP MCB/TP MCB/FP MCB/RCCB/RCBO complete erected on provided angle iron/GI frame. |
| 231 | Supplying and fixing following way SPN sheet steel MCB distribution board 240 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required (but without MCB/RCCB/Isolator) : a) 12 way double door Cat B |
| 232 | Supplying and fixing following way TPN sheet steel, double door, Horizontal type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required ( but without MCB/RCCB/Isolator)(a) 4 way (4+12), double door, Horizontal type Cat B |
| 233 | (b) 6 way (4+18), double door, Horizontal type Cat B |
| 234 | (c) 8 way (8+24), double door, Horizontal type Cat B |
| 235 | (d) 12 way (8+36), double door, Horizontal type Cat B |
| 236 | Supplying and fixing following way TPN sheet steel, double door, Verticle type MCB distribution board 415 V on surface/ recess complete with tinned copper busbar neutral busbar earth bar dinnbar detachable gland plate interconnections phosphotized and powder painted including earthing etc. as required (but without MCB/ RCCB/ Isolator)interconnection between incomer MCB and busbars of following ways (but without MCBs as required) (a) 4 way (8+12), double door, Vertical type, Cat B |
| 237 | Supplying and fixing 6 A to 32 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required.(a) SP, Cat B |
| 238 | (b) DP, Cat B |
| 239 | (c) TPN, Cat B |
| 240 | Supplying and fixing 40 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. - TPN, Cat B |
| 241 | Supplying and fixing 63 A, C series MCB suitable for lighting and other loads of following poles in the existing MCB DB complete with connections testing and commissioning etc as required. TPN, Cat B |
| 242 | Supplying and fixing SP blanking plate in the existing MCB DB complete as required |
| 243 | E : EarthingEarthing with GI earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonry enclosure with CI/RCC cover having locking/Lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 3.0 mtrs(min) and disposal of excavated soil. c)Watering GI pipe, 20mm, Class B, with funnel as per specs. d) Charcoal/salt as per specs ( paid seperately). e) Refilling the pit of size 1.0x1.0x 3.0 mtrs(min) with soft black agriculture soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. Aluminium tag with embossed earthing value to be attached to the pipe.g)watering arrangement(plumbing will be paid seperately). (a) In Soily Strata |
| 244 | Earthing with copper earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonry enclosure with CI/RCC cover having locking/lifting arrangement and watering pipe etc. (but without charcoal or coke and salt) as required as per the Earthing Drawing provided by the Engineer-Incharge.The scope of work includes the following: a) Excavation of pit of size 1.0x1.0x 3.0 mtrs(min) and disposal of excavated soil. c)Watering GI pipe, 20 mm Class B, with funnel as per specs. d) Charcoal/salt as per specs ( paid seperately). e) Refilling the pit of size 1.0x1.0x 3.0 mtrs(min) with soft black agriculture soil of minimum resistivity i/c transportation. e)Masonary chamber with proper foundation, cover plate and locking arrangement. f) Testing of earth value with earth megger and certifications of its value. g)watering arrangement (plumbing will be paid seperately). (a) In soily strata |
| 245 | Extra for using salt and charcoal for GI or copper plate earth electrode as required( 96 Kgs of Charcoal and 5 Kgs of Salt) |
| 246 | Supplying and laying 25 mm x 5 mm GI strip at 0.5 m below ground as strip earth electrode including soldering etc. as required |
| 247 | Providing and fixing 25 mm x 5 mm GI strip on surface or in recess for connections etc. as required |
| 248 | Supplying and laying 25 mm x 5 mm Copper strip at 0.5 m below ground as strip earth electrode including soldering etc. as required |
| 249 | Providing and fixing 25 mm x 5 mm copper strip on surface r in recess for coneections etc. as required |
| 250 | Providing and fixing 4 mm dia copper wire on surface or in recess for loop arthing . as required |
| 251 | Providing and fixing of lightning conductor finial made of 25 mm dia 300 mm long copper tube having single prong at top with 85 mm dia 3 mm thick GI base plate including holes etc. complete as required |
| 252 | Reverting sweating and soldering of copper/ GI tape (with another copper/ GI tape base of the finial or any other metallic object) as required |
| 253 | Providing and fixing GI tape 20 mm x 3 mm thick on parapet or surface of all for lightning conductor complete as required ( for verticle run) |
| 254 | F : Cables, Terminations & Cable trench, Cable Tray etc.Supply of 3 1/2 core armoured PVC/XLPE insulated, PVC sheathed aluminium conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) ,IS:7098(Part I) with latest amendments of following size. a) 3 1/2 Core 300 sq.mmF : Cables, Terminations & Cable trench, Cable Tray etc. |
| 255 | b) 3 1/2 Core 35 sq.mm |
| 256 | Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) , IS:7098(Part I) with latest amendments of following size. - 4 Core 6 sq.mm |
| 257 | Supply of 4 core armoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) , IS:7098(Part I) with latest amendments of following size. - 4 Core 2.5 sq.mm |
| 258 | Supply of 3 core unarmoured PVC/XLPE insulated, PVC sheathed copper conductor cable of 1.1 KV grade with ISI mark conforming to IS:1554(Part I) , IS:7098(Part I) with latest amendments of following size. 3 Core 1.5 sq.mm |
| 259 | Supplying and making cable end terminations with brass compression gland and aluminium lugs for folowing sizes of 3 1/2 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. a) 3 1/2 Core 300 sq.mm |
| 260 | b) 3 1/2 Core 35 sq.mm |
| 261 | Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. - 4 x 6 Sq. mm. |
| 262 | Supplying and making cable end terminations with brass compression gland and copper lugs for folowing sizes of 4 Core PVC insulated PVC sheathed/XLPE aluminium conductor cable of 1.1 KV grade, complete as required. - 4 x 1.5/2.5 Sq. mm. |
| 263 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 120 sq.mm but not exceeding 400 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable)and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. - In Soily Strata |
| 264 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 120 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. - In soily strata |
| 265 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm direct in ground including excavation in the form of a trench as per Cable Trench Drawing provided by the Engineer-Incharge,sand cushioning with screened sand bed of 20mm thick , protective covering with bricks placed breadth-wise on top of cable all over the run( the brick protection shall cover the cable and project atleast 5 cms over the sides of the cable) and backfilling the excavated earth without stones or hard material and making the surface proper with 15 cm crown on the top complete as required. - In Soily Strata |
| 266 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm but not exceeding 400 sq.mm in the existing masonry open duct, etc. complete as required |
| 267 | Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm in the existing masonry open duct, etc. complete as required |
| 268 | Supply and fixing of cable route marker 15 cms diameter of GI plate 6mm thick with inscription theron bolted or welded to 25mm x 25mmx 5mm angle iron 60 cms long and fixing the same in ground with PCC etc complete as required. |
| 269 | G: TELEPHONE, DATA & CCTVSupplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required. a) 20 mm |
| 270 | Supplying, installation and testing of suitable size modular GI box , modular plate and cover complete with RJ-11 connector(modular telephone socket) including concealed metal box/surface GI/PVC Box, modular plate, punching, identifying, complete as required. a) CAT B |
| 271 | Supplying and drawing/fixing indoor type 0.5 sq.mm FR PVC insulated copper conductor unarmoured telephone cable ITD/DOT approved, with GI saddles on wal or in the existing surface/recesed steel/PVC conduit having folowing pair(s), complete as required. a) 2 Pair |
| 272 | Supplying, installation and testing of suitable size modular GI box , modular plate and cover complete with RJ-45 connector (modular LAN socket TX1000/ CAT6) including concealed metal box/surface GI/PVC Box, modular plate, punching, identifying, complete as required. a) Cat B |
| 273 | Supplying and fixing 1 m 24 AWG multi stranded UTP patch cord with RJ-45 factory crimped connector of Cat 6 type, compliant ANSI/TIA-568.2-D standards in position as per specification no. WG-ELVC/PC |
| 274 | Supplying, fixing, and configuring 24 ports, PoE switch compliant with IEEE 802.3 standards with min. 193W PoE capacity with 4GE SFP uplink in provided rack as per specification no. WG-NWC/ENS |
| 275 | Supplying and fixing Cat 6, 24 port patch panel with keystone jacks compliant with ANSI/TIA/EIA 568.C.2 & ISO/IEC 11810 complete as per specification no. WG-NAS/PP |
| 276 | Supplying and drawing of Cat - 6 UTP, 4 pair annealed tinned copper conductor PVC insulated, PVC sheathed, unarmoured data cable in existing surface/recessed steel/PVC conduit of appropriate size including connection, etc. complete as required (a) Cat 6 |
| 277 | Supplying and erecting 6 fibers LSZH armoured multimode optical fiber cable with, core dia 50/125 μm (OM3), suitable upto 10 GBPS, compliant to IEC 60793/IEC 60794 standards, on wall/ceiling or laid in provided pipe/trench as per specification no. WG-ELVC/OFC |
| 278 | Supplying and installing 3 m fiber patch cord LC-LC duplex single mode for OS1/OS2 compliant to IEC 60793/IEC 60794 standards complete as per specification no. WG-ELVC/FPC |
| 279 | Supplying and fixing IP66 ABS enclosure for fiber splicing with raised hinged splice trays to house upto 48 fibers with multiple galnd entry points including heat shrink splice protectors complete. |
| 280 | Supplying, installation and testing of suitable size modular GI box , modular plate and cover complete with modular TV socket including concealed metal box/surface GI/PVC Box, modular plate, punching, identifying, complete as required. (a) CAT B |
| 281 | Supplying and drawing of Co-axial TV cable of required grade, solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in existing surface/recessed steel/PVC conduit of appropriate size including connection, etc. complete as required (a) RG - 6 |
| 282 | Supplying, installing, testing & commissioning of 32/40 Ch Network Video Recorder (NVR), suitable connect Min. 32 IP Cameras, up to 5 Megapixel Resolution, with HDMI1/VGA1 outputs, provided Atleast one HDMI outputof 4K resolution, atleast one VGA output with output up to 1920x1080, Support H.265 or higher, H.264, MJPEG, Supports Redundant Dual Power, Incoming Bandwidth 320 Mbps with minimum 8 SATA ports, ANR Technology,8 SATA interfaces for 8 HDDs and capacity of each HDD up to 8TB, minimum 02 USB port, Alarm I/O 16/4, RJ-45 10/100/ 1000 Mbps selfadaptive Ethernet interface, support multibrand network Cameras, ONVIF conformance, Multiple network monitoring: Web viewer . support protocol TCP/IP, DHCP, DNS, DDNS, NTP, SADP, SMTP, NFS, iSCSI, UPnP™, HTTPS. RoHS, UL, CE, FCC certified.duly erected in provided U Rack with wiring connections, tagging and programming etc. complete as per specifications no. CCTV-NVR |
| 283 | Supplying & erecting of High definition 4/5 Megapixel IP IR Bullet Camera with following features Image Sensor : minimum 1/2.8\\" Progressive Scan CMOS, Video Resolution : minimum 2592 x 1520 Video Compression : H.264, H.265 or higher, at least Three individually configurable stream, Frame rate : minimum 25 fps at all resolutions, WDR : minimum 120 dB Wide Dynamic Range, ONVIF profile conformant, minimum IR distance : 50m, Lens Type : 2.8/4/6 mm Lens, fixed focal, Field of View : 2.8 mm, horizontal FOV 107°, vertical FOV 57°, diagonal FOV 129° 4 mm, horizontal FOV 86°, vertical FOV 47°, diagonal FOV 102° 6 mm, horizontal FOV 55°, vertical FOV 29°, diagonal FOV 65° Lux sensitivity - minimum 0.2 Lux at color, minimum 0.05 Lux at Black & White, 0.0 Lux (IR) Night Vision Distance minimum IR - 50m. Camera minimum Adjustment Angles - Pan : 350°, Tilt : 72°, Rotate : 350°. Power Supply : Support 12VDC & PoE, IP67, IK10 - Vandal Resistant. Built in micro SD/SDHC/SDXC card slot of minimum 128 GB, Built in microphone. minimum Input/Output - Audio in × 1, Audio Out × 1, Alarm in × 1, Alarm Out × 1.Image Settings : Rotate mode, saturation, brightness, contrast, sharpness, gain, white balance. Image Enhancements : Day/Night-Auto (ICR)/Color/Black & White, 3D Digital Noise Reduction, Automatic White Balance, Automatic Gain Control, Backlight Compensation, Highlight Compensation. Events : Privacy Masking, Motion detection, Scene change detection, Face capture, Video tampering, audio exception detection, Region entrance detection, Region exiting detection. Operating temperature ( -30 to 60° C ) . Security - User account and password protection, HTTPS, IP filter, IEEE 802.1X, digest authentication, user access log, TLS1.2, AES - 256, SSH/Telnet closed, FTP disabled. Protocol - DHCP, UDP, HTTP, HTTPS, NTP, DNS, RTP, RTSP, SMTP, SSL/TLS, TCP/IP, Secure Real-Time Transport Protocol (SRTP), Bonjour, SNMP and Secure shell (SSH) supported protocol. RoHS, WEEE, ISO-14001 and REACH compliant, UL/EN OR equivalent BIS/TECH/STQC or any indian standards as applicable, CE, FCC certified. duly erected in position on wall/ceiling/false ceiling/provided pole (mounting height not more than 5 meter) etc with all accessories etc complete as per specification no. CCTV-CAM |
| 284 | Supplying & erecting of High definition 4/5 Megapixel IP IR Dome Camera with following features Image Sensor : minimum 1/2.8\\" Progressive Scan CMOS, Video Resolution : minimum 2592 x 1520 Video Compression : H.264, H.265 or higher, at least Three individually configurable stream, Frame rate : minimum 25 fps at all resolutions, WDR : minimum 120 dB Wide Dynamic Range, ONVIF profile conformant, minimum IR distance : 50m, Lens Type : 2.8/4/6 mm Lens, fixed focal, Field of View : 2.8 mm, horizontal FOV 107°, vertical FOV 57°, diagonal FOV 129° 4 mm, horizontal FOV 86°, vertical FOV 47°, diagonal FOV 102° 6 mm, horizontal FOV 55°, vertical FOV 29°, diagonal FOV 65° Lux sensitivity - minimum 0.2 Lux at color, minimum 0.05 Lux at Black & White, 0.0 Lux (IR) Night Vision Distance minimum IR - 50m. Camera minimum Adjustment Angles - Pan : 350°, Tilt : 72°, Rotate : 350°. Power Supply : Support 12VDC & PoE, IP67, IK10 - Vandal Resistant. Built in micro SD/SDHC/SDXC card slot of minimum 128 GB, Built in microphone. minimum Input/Output - Audio in × 1, Audio Out × 1, Alarm in × 1, Alarm Out × 1. Image Settings : Rotate mode, saturation, brightness, contrast, sharpness, gain, white balance. Image Enhancements : Day/Night-Auto (ICR)/Color/Black & White, 3D Digital Noise Reduction, Automatic White Balance, Automatic Gain Control, Backlight Compensation, Highlight Compensation. Events : Privacy Masking, Motion detection, Scene change detection, Face capture, Video tampering, audio exception detection, Region entrance detection, Region exiting detection. Operating temperature ( -30 to 60° C ) . Security - User account and password protection, HTTPS, IP filter, IEEE 802.1X, digest authentication, user access log, TLS1.2, AES - 256, SSH/Telnet closed, FTP disabled. Protocol - DHCP, UDP, HTTP, HTTPS, NTP, DNS, RTP, RTSP, SMTP, SSL/TLS, TCP/IP, Secure Real-Time Transport Protocol (SRTP), Bonjour, SNMP and Secure shell (SSH) supported protocol. RoHS, WEEE, ISO-14001 and REACH compliant, UL/EN OR equivalent BIS/TECH/STQC or any indian standards as applicable, CE, FCC certified. duly erected in position on wall/ceiling/false ceiling/provided pole (mounting height not more than 5 meter) etc with all accessories etc complete as per specification no. CCTV-CAM. |
| 285 | Supplying & erecting 32\\" professional LED Monitor with 1920*1080 (Full HD) Display, suitable for 16 channel NVR and following features Brightness: minimum 250 Cd/m2 Contrast Ratio: minimum 1000:1 Viewing angle: 178/178 deg. Response time: maximum 8 ms Inputs: HDMI, VGA, BNC, USB, Audio In, Built-in speakers maximum 2 W, Suitable to operate on 100-240 V 50 Hz AC supply and 24/7 Duty Cycle duly erected on wall or table top with standard accessories like wall mount stand and wiring connections etc. complete as per specifications no. CCTV-MON |
| 286 | Supplying & erecting 8 TB internal Surveillance HDD suitable for SATA Port of NVR, interface transfer rate 6 GB/S, maximum sustained transfer rate 210 MB/Sec to 213 MB/S. Drive bay supported 08+, Cameras supported up to 64, Cache (MB) 256, Load/Unload Cycle -3000000, Work Load Rating per Year 180TB, MTBF 1000000 Hrs. HTTPS. RoHS, UL, CE certified, duly erected in position in provided NVR as per specification no. CCTV-HDD |
| 287 | Supplying and drawing/fixing jelly filled outdoor type armoured telephone cable with 0.5 sq.mm dia. tinned copper conductor, ITD/DOT approved, with GI saddles on wal or in the existing surface/recesed steel/PVC conduit having folowing pair(s), complete as required.a) 10 Pair |
| 288 | b) 20 Pair |
| 289 | c) 50 Pair |
| 290 | Supplying, installing, testing and commissioning of Junction Box, ITD/DOT approved, indoor type with wall mounting/concealed facility having front door with lock along with aluminium frame for mounting disconnection type Krone modules, complete cabinet fabricated from 18 SWG CRCA sheet with powder coating in appropriate manner and suitable for following capacity of pairs, including Krone makemodules, crimping and terminations, etc. complete as required.a) 10 Pair |
| 291 | b) 20 Pair |
| 292 | c) 50 Pair |
| 293 | Supplying and fixing 6U wall mount rack (Dimension-DxWxH – 500x550x347 mm) as per specification No. WG-NAS/RAK |
| 294 | Supplying, installing, testing & commissioning push button telephone instrument desk top unit as per specification complete |
| 295 | H : Area LightingMaking M- 20 grade reinforced cement concrete foundation by considering the safe soil bearing capacity at site as 10 T/sq.m at 1.5m depth including supply of steel, concrete, excavation and fixing provided nut bolts with the help of template, duly plastered as per design complete (for 6m to 8m high octagonal /conical GI pole). |
| 296 | Providing & erecting 5 m high (clear height) galvanised octagonal pole with foundation bolts having bottom of 130 mm A/F, top 70 mm A/F on provided foundation as per specification no. OH-PL/OPL. |
| 297 | Supplying and erecting GI pipe 50 mm dia.‘B’ class at position with accessories complete as per specification no. CW-PLB/GP |
| 298 | Supplying and erecting Street light bracket made from 25 mm. dia ‘B’ class G.I. Pipe, 0.6 m in length along with pole cap of 300mm length and 80 mm dia duly welded with provided leads as per specification no. FG-BKT/BPC |
| 299 | Supplying and erecting integrated LED street light fitting 26 to 30W IP65 & IK08 class having single piece pressure die-cast aluminium housing , having system lumens output of Min. 2600 Lumens, min. efficacy of 100 lumen/W, CRI>70, CCT upto 6500K, THD<10%, p.f. >0.95, operating range of 140-270V, inbuilt surge protection of 10 kV, Life class of 50,000 Hrs at L70B50 including driver complete with minimum 2 Years warranty as per specification No. FG-ODF/SL. |
| 300 | I : UPSSupplying, erecting, testing & commissioning of 2 kVA capacity on line pure sine wave,PWM,IGBT based UPS with 0.8 to unity output pf, single phase input & 1 phase output complete with all protections as per specification no. APUPS(Without batteries) |
| 301 | Supplying and erecting 12V/26Ah SMF battery with battery terminal wire, duly charged with 24 months warranty complete |
| 302 | I : LT PanelsSupply, Fabrication, Erection, Testing & Commissioning of Main Panel floor mounted with frame of suitable M.S. channel dully painted, fabricated of 14/16 swg CRCA sheets completely derusted, chemically treated and powder coated with shade suggested by client and having following items as per single line diagram:- 250 A Adjustible 35/40 KA - 1 no. wiring for ammeter having Three & half digit LED display, external C.T. operated, calibrated for suitable to operate on 500V, 0 to1000A AC supply, L.T. Current Transformer with bar primary 50/5 to 1000/5 ratio with 15VA, 3 pilot lamps all Bakelite with colour glasses with miniature lamps 230 V/250V from GED connected to 315A, 4P ATS having DG Supply which consist of 250 A Adjustible 35/40 KA - 1 no. wiring for ammeter having Three & half digit LED display, external C.T. operated, calibrated for suitable to operate on 500V, 0 to1000A AC supply, L.T. Current Transformer with bar primary 50/5 to 1000/5 ratio with 15VA, 3 pilot lamps all Bakelite with colour glasses with miniature lamps 230 V/250V & outgoing of 8 nos 63A, 4P, MCB, 8 nos 40A, 4P, MCB, 1 no 25A, DP, RCBO and 1 no 63A, 4P, RCBO as per single line drawing of MLTP |
| 303 | Providing pair of duly tested rubber hand gloves as per IS :47705 suitable for working upto 22 kV supply complete. |
| 304 | Supplying and fixing PVC synthetic elastomer electrically insulating mat with class B insulation conforming to IS: 15652 – 2006 having 2.5 mm thickness upto 11 kV |
| 305 | J: PumpsSupplying & erecting, testing and commissioning of Minimum three & above star rated Centrifugal water pump (Monoblock), 230V, Single phase 50 cycles A.C. supply of 1.5 kW/2 HP with discharge 600/140 Litres per Minute (LPM) for head of 8/22 m & 50 mm suction/ 50 mm delivery pipe on provided C.C. foundation as per specification No. WP-CGP |
| 306 | Supplying & erecting,testing and commissioning of automatic control panel for 1 Ph, 230 volt, A.C. Submersible/centrifugal pump set up to 3 HP consisting of DOL starter Of suitable relay range S.P.P., Combined ammeter/ voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. |
| 307 | K: SolarSupplying, installing, testing and commissioning of 25 kWp ON-GRID Solar pV System / Plant consisting Solar PV Poly Crystalline Panel (335 Wp X 75 Nos.) and Solar ON-GRID Inverter of similar capacity (THD<3%) with interconnecting wires / cables up to solar ON GRID inverter, proper base plate, canopy box to house Inverter and necessary accessories i.e. ACDB/ DCDB, MCB etc. wiring up to solar Inverter in casing and capping, display board, sign board, two distinct earthing, lightning arrester, liasoning charges, remote monitoring system with maintaining card / chip for 5 years including net charges for RMS System, complete upto net meter installation and export to the grid with 5 year ON-SITE warranty and 5 Years fully comprehensive maintenance contract as per Specification no. ESD-RT-ONG. (25 meter length of aluminium conductor armoured cable of appropriate size to be considered) |
| 308 | Supplying and installation of solar PV module cleaning unit consisting of nozzles spray, necessary pipes, valves, post, electronic panel board concealed with weather proof cabinet, spreading water periodically for removal of dust, related motor pump, controller, timer and nozzles set suitable for covering 25 kWp Solar PV Module. (Approx. 175 Sq. Mtr. PV Module area) |
| 309 | 16 FIRE DETECTION AND PROTECTION WORKSPumps and other accessories For Hydrant SystemSupplying, installation, testing and commissioning of booster fire pump [BP] suitable for water discharge of 900 LPM at 35 m head driven by electric motor 415 volts, 3 phase 50 Hz, AC supply of 7.5 kW or of suitable kW capacity for manual/automatic operation and consisting of following :(a) Horizontal/vertical type, single/multi stage, centrifugal casing pump of cast iron body & bronze/CI impeller with stainless steel shaft (SS410 grade), mechanical seal conforming to IS 1520.(b) Squirrel cage induction motor, TEFC, synchronous speed 3000 RPM, suitable for operation on with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325.(c) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required.(d) Erected on provided suitable size cement concrete foundation duly plastered with anti vibration pads with perfect aligning, proper levelling complete pump set with accessories duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete, as per specification no. FF-MFP/BP |
| 310 | Supplying, erecting, testing and commissioning of automatic control panel for three phase , 415 V, A.C. supply, submersible/centrifugal pump set upto 7.5 HP consisting of D.O.L. starter having relay range 9-14 A, S.P.P., combined ammeter/voltmeter, phase indicating lamp enclosed in CRCA powder coated vibration proof enclosure with IP54 protection with single phasing, phase reversal, phase imbalance, etc. |
| 311 | Supplying and erecting 75/80mm mm dia Cast Iron end line strainer of Y-type flanged end pattern, PN16 pressure rating, SS screen, end connection with Flanged / Screwed / Socket Weld / Butt Weld End etc with standard OAR (open area Ratio) for positive suction complete as per specification no. FF-VL/ELS |
| 312 | Supplying and erecting 75/80 mm dia. cast iron double flange sluice valve complete with PN16 pressure rating, as per specification no. FF-VL/SV |
| 313 | Supplying and erecting 100 mm dia. cast iron double flange sluice valve complete with PN16 pressure rating, as per specification no. FF-VL/SV |
| 314 | Supplying and erecting 75/80 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV |
| 315 | Supplying and erecting 100 mm dia. cast iron double flange butterfly valve of size complete with PN16 pressure rating, as per specification no. FF-VL/BFV |
| 316 | Supplying and erecting 75/80 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV |
| 317 | Supplying and erecting 100 mm dia cast iron double flange NRV complete with PN16 pressure rating, as per specification no. FF-VL/NRV |
| 318 | Supplying and erecting 25 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV |
| 319 | Supplying and erecting 50 mm dia gun metal gate valve complete with PN16 pressure rating, as per specification no. FF-VL/GV |
| 320 | Supplying and erecting 25 mm Ball Valve complete with PN16 pressure rating, as per specification no. FF-VL/BV |
| 321 | Supplying and erecting 50 mm Ball Valve complete with PN16 pressure rating, as per specification no. FF-VL/BV |
| 322 | Landing valve, Hose Reel & Other accessories for Hydrant System etc.Supplying and erecting Stainless Steel single outlet hydrant valve fitted with necessary accessories complete as per specification no. FF-VL/HV. |
| 323 | Supplying and installing wall mounting swinging Hose reel drum fitted with 19 mm dia. 30 meter long high pressure polypropylene (Polyhose) along with necessary accessories complete. As per specification no. FF-FFA/HV |
| 324 | Supplying and erecting 63mm dia,Reinforced Rubber lined (R.R.L.) Hose pipe, 15 m in length, fitted with necessary accessories complete as pre specification no. FF-FFA/RRL |
| 325 | Supplying & erecting Stainless steel branch pipe of 63 mm dia. Fitted with 20mm dia detachable hexagonal nozzle complete as per specification no. FF-FFA/NZ |
| 326 | Supplying and erecting 150 mm dia fire brigade header suitable for supplying water in fire tank complete as per specification no. FF-FA/FBC |
| 327 | Supplying and erecting 20/25mm dia gun metal air release cock, with necessary G.I. coupling to be fitted on top of air vessel or on wet riser complete as per specification no. FF-FFA/ARV |
| 328 | Supplying and erecting 100 mm dia pressure gauge , 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, erected with provided G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG |
| 329 | Supplying and erecting 12/15 mm dia. pressure switch with provided Isolation valve, G.I. nipple, elbow, etc. complete as per specification no. FF-FFA/PS |
| 330 | Supplying and erecting M.S./CRCA cabinet for housing Fire Brigade/ SIEMESE connections (size 1250 x 400 x 300 mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4 mm. having front doors with viewing glass (8\\"x6\\") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003). |
| 331 | Supplying and erecting M.S./CRCA cabinet for housing double hose pipe with nozzle (size 750 x 600x 250 mm.) made from 16 SWG sheet and angle iron 25 x 25 x 4 mm. having front doors with viewing glass (8\\"x6\\") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour( Code 538 of IS 5) |
| 332 | Piping Hydrant/ Sprinkler/ Pump roomSupplying and erecting G.I. pipe 'C' class ERW (Electrical Resistance Welding) 25 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification no. FF-PP |
| 333 | Supplying and erecting G.I. pipe ‘C’ class ERW 50 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification No. FF-PP |
| 334 | Supplying and erecting G.I. pipe ‘C’ class ERW 65 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification No. FF-PP |
| 335 | Supplying and erecting G.I. pipe ‘C’ class ERW 75/80 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification No. FF-PP |
| 336 | Supplying and erecting G.I. pipe ‘C’ class ERW 100 mm dia with necessary fittings duly painted with two coats of synthetic enamel paint of fire red colour over a coat of primer (ISC code 536 as per IS 2932 of 2003) complete as per specification No. FF-PP |
| 337 | Providing coating of Bitumen Paint & pipeline corrosion resistant Pypkote tape conforming to IS 10221 Appendix B specification having 4mm thick Wrapping for underground 100 mm Ring Main of Fire Fighting System.(Pypkote tape comprises of a Tar based Polymeric mix supported on a fabric ofhigh tensile strength Fibreglass). |
| 338 | Fire Detection SystemSupplying, installing, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central processing unit with the 2 loop capacity and capable of supporting upto 250 devices and detectors per loop, with on-board LCD alphanumeric backlit display suitable for minimum 80 characters operating at 230 V 50 HZ - AC with inbuilt Battery Backup of a minimum 24 hours in normal condition and 30 min in alarm condition, The panel shall have suitable provision for network connectivity & compatible for third party integration(Open Protocol to communicate) via a MODBUS/BACNET interface etc. conforming to IS 15908:2021, IS 2189: 2008, NFPA-72,EN 54 & VDS / FM/ UL 864 (10th edition) with 3 years replacement warranty and inclusive of lifetime software license validity , as per specification no FF-AFAS/CP. |
| 339 | Supplying, installing, testing and commissioning of Addressable Optical Photo Smoke Detector. The detector shall have multi co-operative sensing technology for faster response & avoid false alarms. The detector shall have single/twin bicolour LED for 360 deg viewing. The detector is conforming to IS 2189: 2008, 11360_1985_Reff2020_EN 54 /VdS / UL & FM approved with 3 years equipment replacement warranty, Designed to meet UL268, 7th Edition. FFAFAS/SD. |
| 340 | Supplying, installing, testing and commissioning of intelligent addressable thermal/heat detector with rate of rise cum fixed temperature thermistor complete with 0°C to 58°C temperature range, with base as required, single/twin LED’s with 360 degree view, in-built locking mechanism to check the removal and pilferage of the detector, Detector Shall conforming to IS : 2175 - 1988 reaffirmed 2000, IS 15908:2021 / EN 54 / VdS / UL & FM approved with 3 years equipment replacement warranty, Designed to meet UL268, 7th Edition. FF-AFAS/HD - ROR. |
| 341 | Supplying, installing, testing and commissioning of addressable manual call points ( break glass type/pull station type), made of addressable break glass plastic square in shape surface/flush mounted with \\"Break Glass\\" massage embedded on the glass, complete erected with mounting base and required accessories conforming to EN 54 /VdS or UL & FM approved with 3 years equipment replacement warranty as per specification no FF-AFAS/MCP. |
| 342 | Supplying, installing, testing and commissioning of addressable Sounder cum strobe rated at minimum 75 dB @ 3m for Audible annunciation and minimum 75cd flashing at 1 Hz for visual indication.Module shall conforming to IS 2189: 2008, IS 15908:2021 / EN 54/VdS / UL & FM approved with 3 years equipment replacement warranty as per specification no FF-AFAS/S-ST. |
| 343 | Fire Extinguishers Supplying and fixing of self expanding, ready to use polyurethane(PU) foam sealant of minimum 750ml bottle, suitable to seal the openings of all kinds of cables, pipes and cable support system in steel, aluminium and plastic profiles (except hollow core conductors). Sealant shall have minimum 2 hour fire rating, conforming to EN 1366-4:2021 as per specification no FF-FRS. |
| 344 | Supplying and fixing standard first aid box with necessary antiseptic cream, medicine for use on wounds due burn, crepe bandage, gauge bandage, medicated ready to use bandage (Band-Aid) adhesive tape for medicinal use, scissors, anti-septic solution, etc. (All above contents shall be of standard makes) |
| 345 | Supplying and fixing PVC synthetic elastomer electrically insulating mat with class A insulation conforming to IS: 15652 –2006 having 2 mm thickness upto 3.3 kV |
| 346 | Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. Capacity Cartridge type conform To IS 2878/ 15683 Complete erected with necessary clamp made front 50 x 6 mm. M. S. flat with nut & bolts grouted in wall complete. |
| 347 | CablingSupplying, installing, testing and commissioning FR, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CB-LT/CU |
| 348 | Supplying and fixing of following sizes of rigid PVC conduit alongwith accessories in surface(medium)/ recess(heavy) including cutting the wall and making good the same in case of recessed conduit as required. - 25 mm |
| 349 | 17 BUILDING STRUCTURE DEMOLITIONS AND DISMANTLINGNote 1 : The Sums entered shall be disbursed in proportion to the percentage of work carried out as assessed monthly by the Contractor and agreed or modified by the Engineer based on progress relative to the Contractors Contract Programme or subsequent modifications to the Programme.Note 2 : The Sums entered shall include for the provision, operation, upkeep and maintenance of all necessary transport plant and equipmentNOTE 3: The area of structures as listed below for demolition are approximate and contractor may actually verify the same at site prior to quoting.Demolition of entire structure above floor level including removal and stacking of structural steelwork, Asbestos Cement / G.I sheets from roofing and cladding including ridges, hips, valleys and gutters , downtake pipes, reinforced and mass concrete,RCC grills, brickwork, laterite work,staircases, doors, windows, clerestory windows, ventilators, shutters (steel,aluminium or wood),M.S. grills,Rolling Shutters,M.S. sliding doors, , ceiling or partition hard board, electrical wiring, switch boards, distribution panels, fittings and fixtures and other appliances. Rate to include removal of all accessories, transportation, handling, and temporary stacking of dismantled debris, and all other serviceable materials at location on site as specified and directed by GSL and disposal of all unsuitable material to an approved landfill site outside GSL premises. The demolition/ dismantalling as above for the following workshops.(The Contractor to access the quantum of work by conducting site visit as required) Including to Allow for demolition of concrete foundations (plain / reinforced concrete), masonry walls of the building/structures as listed above for the portion below floor level. Rate to include providing and removing shoring, dressing of sides, temporary works, dewatering wherever required, ramming of bottoms, backfilling and compaction of suitable excavated material and disposal of unsuitable material outside GSL premises at approved landfill sites. -Powerhouse (15m x 24.55m) & Fire Station (8.5m x 16.55m) |
| 350 | Removal of all the debris, waste, rubbish, etc from the construction site including cutting of vegetation, trees, if any, dismantling of fencing along the shoreline, light poles, fixtures, loose water tanks, other materials, small structures, drains, existing tanks,any other structures, trenches, etc as required for undertaking the works defined in the scope of the present contract. The rate to include stacking of serviceable materails and disposal of unsuitable material outside GSL premises at approved landfill sites. |
| 351 | Demolition of roads and pavement (light duty and heavy duty) including plain or reinforced concrete, asphalt concrete, underground trenches, concrete hardstanding/paving to roads, including foundations of existing structures as required. The exact extent of all demolition shall be agreed with the Engineer before demolition of any structure commences. Rate to include removal of all accessories, re-transportation, handling, and stacking of dismantled debris and all other serviceable materials at location on Site as specified and directed by GSL and disposal of unserviceable material to an approved landfill site. Sum to include for the provision, operation, upkeep and maintenance of all necessary transport equipment. |
| 352 | Note:- qty of this Item is (-)1, Each18 SCHEDULE OF CREDIT Allow for the full and inclusive cost of the removal of existing EOT cranes in existing Workshops. Rate to include removal of all accessories, re-transportation, handling, and stacking of dismantled materials, accesories, rails, etc and all other serviceable materials at location on Site as specified and directed by GSL and disposal of unserviceable material to an approved landfill site. All plant, equipment, labour and materials etc.complete. -Powerhouse (5 Ton) |
| 353 | Note:- qty of this Item is (-)181.72 cumRebate for taking laterite stones including carting away, loading, unloading etc. complete |
| 354 | Note:- qty of this Item is (-) 356.41 QunitalRebate for taking all types of steel items including carting away, loading, unloading etc. complete |
| 355 | 19 CRANE AND LIFTING EQUIPMENTSSupplying, Installation, Testing and Commissioning of 5 Ton EOT crane including design, manufacturing, assembly, testing & inspection at manufacturer's works, packing, dispatch, transportation, safe delivery at site, required fabrication at site, installation, testing & commissioning, performance testing, final painting at site, statutory approvals and handing over as per detail specification attached. |
| 356 | 20 AIR CONDITIONING WORKSupplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.0TR to 1.2TR capacity having ISEER minimum 3.8 to maximum 4.39 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. AP-AC/ SAC. |
| 357 | Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.3TR to 1.6TR capacity having ISEER minimum 3.8 to maximum 4.39 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. AP-AC/SAC. |
| 358 | Supplying, installing, testing & commissioning split type variable speed inverter technology with minimum 3 to 1 convertible mode for compressor, room air conditioning unit 1.7TR to 2.0TR capacity having ISEER minimum 3.8 to maximum 4.39 suitable to operate on 250V, 50 Hz, A.C. supply having 1 no of air handling unit hi-wall/floor mounting type complete with refrigerant R32 having copper condenser, minimum 2.5PM filter, self diagnosis feature, stabilizer free operation & temperature display on indoor unit, noise level maximum 50dBA at position as per specification no. AP-AC/ SAC. |
| 359 | Supplying and erecting fully automatic line Voltage stabilizer buck and boost type for operation on input voltage 160 to 270 V and output voltage 230 V + 1% rated for 3 kVA maximum load and with voltmeter, selector switch, 6A/16A flush type 3 pin socket for output and with 3 core flexible cord and 3 pin 6/16 A plug top complete with overload & short circuit protection. |
| 360 | Supplying and erecting fully automatic line Voltage stabilizer buck and boost type for operation on input voltage 160 to 270 V and output voltage 230 V + 1% rated for 4 kVA maximum load and with voltmeter, selector switch, 6A/16A flush type 3 pin socket for output and with 3 core flexible cord and 3 pin 6/16 A plug top complete with overload & short circuit protection. |
| 361 | Supplying and erecting fully automatic line Voltage stabilizer buck and boost type for operation on input voltage 160 to 270 V and output voltage 230 V + 1% rated for 5 kVA maximum load and with voltmeter, selector switch, 6A/16A flush type 3 pin socket for output and with 3 core flexible cord and 3 pin 6/16 A plug top complete with overload & short circuit protection. |
| 362 | Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 12mm complete as per specification no. AP/AC-CP. |
| 363 | Supplying & erecting seamless outside & inside, smooth, dry and clean copper pipe with ROHS compliant suitable for refrigerant having 22SWG thickness and inner dia/size 16mm complete as per specification no. AP/AC-CP. |
| 364 | Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 12 mm for solar water heater/AC system. |
| 365 | Supplying and erecting elastomeric nitrile rubber / foam tube type sleeves for coating and insulating on provided PC / copper pipes having 9 mm thickness and inner diameter / sizes 16 mm for solar water heater/AC System. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 30, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 13, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 11 daysOct 13, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 11 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender