Tender For repair renovation Of Lwss Kirri-Shawalla In G.P.Kirri Tehsil Nerwa Distt. Shimla (H.P). (Sh:-Replacement Of 20 Hp Submersible Pumps Sets And Construction of Reinforced Cement Concrete S/Well 1,00,000 Cap. At Stage Ist Etc.) Under Pdna
Tender Value
12.48 Lakhs
Estimated cost
Bid Submission
09 Oct 2026
6 days left
EMD
31223
Bank guarantee accepted
Document Fee
500
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Shimla → Himachal Pradesh
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender for repair renovation Of Lwss Kirri-Shawalla In G.P.Kirri Tehsil Nerwa Distt. Shimla (H.P). (Sh:-Replacement Of 20 Hp Submersible Pumps Sets And Construction of Reinforced Cement Concrete S/Well 1,00,000 Cap. At Stage Ist Etc.) Under Pdna
BOQ
| Sl. No. | Item Description |
| 1 | Providing and installation of submersible pump confirming to ISS9034-1976 along with a directy coupled submersible type squrrile cage electric induction motor suitable for operation on 415-+10% volts 3 phase 50 cycles AC supply water lubericated bearing i/c Supply and fixing of control panel complete with sheet and angle iron fabricvated dully painted and complete with intermal wiring and comprising of air break star delta starter complete with GPSM system to operate through mobiles main switch of suitable amperage T.P. Volt meter an meter phase indicate , Supply and fixing of submersible cable sets 6mmsqmt( 50m length ) Providing and fixing of reputed make of 65mm cast Steel double flanged cast steel reflux valve 1 no of various dia. with req. accessaries in 65 mm dia,rope wire 4mm dia suitable to bear the wight of submersible motor pump set and GI pipe etc . suitable for operation on the data given below i/c the cost all accessoreis in all lead lift & carriage of material at site as per direction of Engineer-Incharge. complete with pannel, ( Stage 1st 1X20 HP) |
| 2 | Excavation in foundations , trenches etc., in earth work , lift up to 1.50 metres. Stacking the eacavated soil not more than 3 metres clear from the edge of the excavation and then returning the stacked soil in 15 cm. (fifteen centimetres) layers , when required in to plinth and sides of foundations etc., conslolidating each of the disposited layer by ramming and watering and then disposing off all excavated soil as directed with in the load of 20 mtrs. Pick and Jumper work etc. complete as per the direction of the Engineer - in - Charge. |
| 3 | Providing and laying cement concrete 1:4:8 (1cement:4sand:8graded stone agg. 40mm nominal size)and curing complete excluding cost of form work in :- a) Foundation and plinth. |
| 4 | Providing and laying cement concrete 1:11/2 :3 ( 1cement: 1 1/2 sand: 3graded stone aggregate 20 mm nominal size )and curing complete excluding the cost of form work and reinforcement in:- |
| 5 | foundation footing and bases of columns & like mass concrete. |
| 6 | Walls(any thickness but ot less than 0.1 mtr thickness) attached pilasters, buttresses, plinth and string courses etc. from top of foundation level up to floor two level. |
| 7 | Providing & laying CC 1:2:4 1cement:2 sand 4 graded aggregates 20mm nominal size curing complete excluding cost of form work & reinforcement for RCC work in:- with in all leads and lifts as per the directions of the Engineer in charge. |
| 8 | In suspended floor roofs landing shalves & their support balconies,beams, girders bressumers cantilevers upto floor two level |
| 9 | Providing form work with steel plates 3.15mm thick so as to give fair finish I/c centering shuttering propping etc. height of propping below supporting floor to ceiling not exceeding 4mt. Height & removal of same in situ reinforce ment concrete and plain concrete work in :- |
| 10 | Vertical surface such as walls(any thickness) partitions and the like including attached pillasters, butteresses, plinth and string courses and the like. |
| 11 | Flat surfaces such as soffits of suspended floor roofs landing & like floor etc.,upto 200mm thickness. |
| 12 | Edge of slab and break in floor 20 cm wide |
| 13 | Providing mild steel/tor steel reinforcement I/c bending binding and placing in position complete |
| 14 | Steel work welded in built up sections, trusses and framed work including cutting hoisting Fixing in position and applying a priming coat of red lead paint :- |
| 15 | In trusses and trussed purlings in buildings. |
| 16 | White washing with lime on undecorated wall surfaces (two coats) to give an even shade including thoroughly brooming the surface to remove all dirt dust mortor drops and other foreign matter. |
| 17 | Prov. and fixing GMS tubes from S/well to Pump House etc. including providing and fixing Cast iron Reflux Valve 300mm dia of Class PN 1 (80mm) dia.make includind MS Falnges conforming to IS:6392-1971 of table 5 & welding of MS Flanges in two Layers on both faces including carriage complete in all respect as per entire satisfaction of Engineer in Charge. etc. Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedOct 09, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 6 daysOct 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 6 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender