Tender For Addition/Alteration And Special Repair To Certain Md Accn At Dinjan Mil Stn Under Ge Dinjan
Tender Value
8.64 Crore
Estimated cost
Bid Submission
02 Nov 2026
29 days left
EMD
7.57 Lakhs
Bank guarantee accepted
Document Fee
3000
Non-refundable
Tender Type
Online
Tender Overview
Organization
Tender ID
Competition Type
NCB
Bidding Type
Tender
Location / State
Tinsukia → Assam
EMD Exemption
Available
Quantity
Not Available
Website
Contact Person
Address
Project Description
Tender For Addition/Alteration And Special Repair To Certain Md Accn At Dinjan Mil Stn Under Ge Dinjan
BOQ
| Sl. No. | Item Description |
| 1 | Demolition of cement concrete in ground floor n exc 15 cm thick (un reinforced) complete all as specified and directed. |
| 2 | M&L for PCC 1:2:4 type B0 (using 12.5 mm graded crushed stone aggregate) as in chajjas top, laid to a minimum consolidated thickness of 25 mm as leveling course, laid and compacted in min slope 1:30 over top of chajja complete all as specified& directed by Engr-in-Charge. |
| 3 | Dismantling of plain or corrugated sheeting all as specified. |
| 4 | Dismantling Asbestos cement (corrugated, semi corrugated, etc.) sheets in roof coverings. |
| 5 | S & F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified. |
| 6 | S&F Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified. |
| 7 | Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets as directed. |
| 8 | S&F for aluminium anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with screws and with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain) pre painted, HSPC fixed to frame complete all as specified and as directed by Engr in charge. |
| 9 | Dismantling timber scantlings unframed work 40 sqcm and over in section in any position complete all as specified and directed. |
| 10 | Dismantling timber in unframed, fillets, rails, posts, rafters,purlins, etc. under 40 sq. cm in section |
| 11 | S/F 2nd class hard wood scantling as in purlins rafters ,& timber fixed work etc wrought complete all as specified and directed. |
| 12 | All as per item No. 11 above but except timber complete all as specified and directed. |
| 13 | S/F 2nd class hard wood scantling as in purlins rafters ,& framed work etc clean sawn complete all as specified and directed. |
| 14 | All as per item No. 13 above but except timber complete all as specified and directed. |
| 15 | M&L II nd class hard wood plain fillets square or rectangular in section cleansawn sectional area exc13sqcm and nexc 25 sqcm secured in nails complete all as specified and directed |
| 16 | Demolition of reed, lathing single or double, including battens and plaster or chicken wire lathing complete all as specified and directed. |
| 17 | M&L GI wire netting 0.71 mm dia and 12 mm mesh lathing in to reed in walls incl all laps cutting and waste complete all as specified and directed. |
| 18 | M&L 15 mm thick plastering in CM 1:4 on one side of lathing in two separate layers even and smooth without using extra cement incl WPC complete all as specified and directed. (Note: WPC shall be measured seprately) |
| 19 | M&L 15 mm thick plastering in CM 1:6 the other side of lathing finished even and smooth without using extra cement complete all as specified and directed. |
| 20 | M &L for Preparing surfaces of wood and wood based materials,new or old, of any description and girth, not otherwise described and treated with Creosote complete all as specified and as directed |
| 21 | M&L for preparation of old wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coats of synthetic enamel paint all as directed by Engr in charge |
| 22 | M & L for two coats of synthetic enamel paint over a coat of pink primer,to new wooden surface of any description notexc 10 cm girth or width including prepration of new/old wooden surfaces complete all as specified and directed. |
| 23 | M&L for preparation of old painted steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and as directed. |
| 24 | Taking down chowkats or frame, n. exc 1.5 sqm each with shutters (without taking off shutter from the frame) as directed. |
| 25 | Taking down chowkhats or frames with shutter (without taking off shutter from the frame) exe 1.50 & n.exc. 4 sqm in each complete all as specified & directed. |
| 26 | Dismantling wrought iron or mild steel work of any description not otherwise provided for. |
| 27 | S&F solid PVC moulded door frame of size 50mmx47mm made out of 5mm, single side prelam PVC sheet used and edges will be painted to match with printed to match with prelam sheet, reinforced with MS square tube & fixing in opening including hold fast. |
| 28 | S&F factory made solid PVC Moulded door shutter 28 to 30mm thick (Stiles) with 2,4 or 6 raised panel design with 2mm thick Moulded Prelam PVC Sheet on front face & 2 mm plain colour PVC sheet on back face, supplying and fixing in frame at site as per specification and directed. |
| 29 | S&F 75 mmx47mmx1.80mm size stainless steel SS 304 grade butt hinges with stainless steel screws as per IS- 12817 complete all as specified and as directed. |
| 30 | Supply and fix in for 150mm long stainless steel SS 304 gde barrel tower bolts of extruded section complete all as specified and as directed. |
| 31 | M & L MS flat iron work as in hold fast and similar small articles, cut to length, bent to shape, drilled hole and fixed with screw etc conforming to Fe-290 Gde-E-165 complete as specified and directed. |
| 32 | S & F pressed steel frames for door 105mm X 60mm with revates including necessary fittings lugs, hings, lock strike plate, etc complete as specifieds, supplied and fixed complete all as specified and directed by Engr in charge |
| 33 | S&F pressed steell door frame 125x60 mm for doors with one or more rebates including necessary fixing lugs hinges lock strike plates comlete as specified and directed by engr in charge(pcc filling of holloow section measured and paid seprately) |
| 34 | M&L Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 or E-165 |
| 35 | S&F 30mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides Ditto, but with particle board core |
| 36 | S & F 35mm thick, 2nd class hard wood, glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete as specified and directed . Sizes of members of shutters as specified in SSR Part I, Section -8, clause 8.24 (a). |
| 37 | S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/ Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2 , modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made. |
| 38 | Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid decorative type flush door shutter of size 18mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer In- Charge. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately) |
| 39 | S & F stainless steel soft close hydraulic clip concealed cabinet hinges fixed with stainless steel screws complete all as specified |
| 40 | S & F Width of flaps (when open) 40mm Continuous (piano) hinges,stainless steel, bright finish or electrogalvanised complete all as specified & directed by Engr-in-Charge. |
| 41 | S & F 75 mm size stainless steel Hasp and staple, safety type with stainless steel hinge pin including bolt to hinge plate and fixed with screw. |
| 42 | S & F 50mm dia polished hard wood knobs fixed with thread screw and nut complete. |
| 43 | S & F stainless steel magnetic door catched magnet of size 50 X 15mm fixed with stainless steel screw on shelf/sides wall and shutter complete all as specified and as directed |
| 44 | S & F galvanised stainless steel wire cloth, 12 mm nominal dia of mesh and average width of aperture 1.4 mm and fixed with tinned tacks or galvanised wire staples complete. |
| 45 | S&F 100mmx58mmx1.90mm size stainless steel SS 304 grade butt hinges with stainless steel screws as per IS- 12817 complete all as specified and as directed. |
| 46 | Supply and fix for 150mm long stainless steel handles, with stainless steel screws complete all as specified and as directed. |
| 47 | Supply and fix 250mm long stainless steel, sliding door bolt with hasp,staple (bolt type) and fixing clips and fixing bolts and sliding bolts of stainless steel and fixed complete all as specified and as directed. |
| 48 | S&F Floor door stopper of Stainless steel 304 Gde, with hard drawn steel spring overall length of cover plate 140mm, fixed in floor complete all as specified and directed |
| 49 | M & L preparation of new untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of Synthetic enamel paint over a coat of pink primer complete as specified and directed. |
| 50 | S & F in repairs curtain rails, harrison rail, aluminium alloy chromium plated with fixing brackets, stops, rollers etc. |
| 51 | S&F Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors,windows, ventilators andpartitions (Fixed portions) withextruded built up standardtubular sections/ appropriate Z sections and other sections of approved make conforming to IS:733 and IS:1285, fixing with dash fasteners of required dia and size,including necessary filling up the gaps at junctions, i.e. at top,bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle,Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge. |
| 52 | S&F Powder coated aluminium (minimum thickness of powdercoating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and makingprovision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snapbeading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-charge. |
| 53 | S&F Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Windowprofile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of wateretc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed tothe wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. (Note: The unit rate quoted by contractor excludes cost of glass and includes all other connectedaccessories. Net Opening will be measured lor payment purpose.)(A) Area not exceeding 2.00 sqm each |
| 54 | Supply and fixing factory made uPVC white colour fixed glazed window/ventilator made of (small series) frame 47 x 50 mm mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area upto 0.75 sqm.)comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process ofrequired length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I. fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of ngineer-in-Charge. (Glass shall be paid separately).Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. |
| 55 | Material and labour for providing and injecting chemical emulsion for post constructional anti termite treatment along the external wall below concrete or masonry apron using chemical emulsion at the rate of 2.25 litre peri linear metre including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 Cement : 2 Coarse sand) to match the existing floors drilling and plugging holes etc complete all as specified and as directed. |
| 56 | M & L for Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors |
| 57 | Material and labour for providing and injecting chemical emulsion for post constructional anti termite treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre / hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same with cement mortar (1:3) & painted with white or coloured paint complete all as specified and as directed |
| 58 | Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove, dust etc. as directed. |
| 59 | Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises as directed. |
| 60 | M & L 25 mm thick PCC type B0 1:2:4 (using 12.5 mm graded stone aggregate) as in sub base to maintain level all as specified and directed. |
| 61 | M&L for ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement morter (1:4) for laying of floor finishes complete all as specified and directed. |
| 62 | M&L for ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18sqm but not exceeding 0.38 sqm, on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10mm thick backing coat in cement & sand mortar 1:3 complete all as specified and as directed. |
| 63 | M&L Non skid ceramic tiles 7 to 8mm thick area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm 7mm thick coloured tiles in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over screed bedding 15mm thick in CM 1:4 as specified and as directed. |
| 64 | M&L Non skid ceramic tiles 7 to 8mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm 7mm thick coloured tiles in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match, over screed bedding 15mm thick in CM 1:4 as specified and as directed. |
| 65 | M&L for glazed ceramic tiles in vertical surface 300x450x7mm thick in dado over 10mm thick rendering in CM 1:4 on walls set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade as specified and as directed |
| 66 | Dismantling of stone slabs or tiles of any description or thickness as in floors, pavings, aprons, pathway etc laid dry or laid dry and pointed complete all as specified & directed. |
| 67 | M & L 75 mm thick PCC type D-2 1:4:8 ( using 40mm graded stone aggregate) as in sub base all as specified and directed. |
| 68 | M&L for prepolished, chequered cement concrete tiles of size 20cmx20cmx25mm thick, as in floors etc, including 15 mm thick screed bed or bedding in cement mortar (1:6) and set and jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and as directed. |
| 69 | M&L Pre-cast (Factory casted) cement concrete Kerb stone casted in PCC (1:2:4) Type B-1 using 20mm graded stone aggregates with plan or interlocking joints (as directed) with solid blocks, exc. 10 cm in width and setting and jointed in cement mortar 1:6, complete all as specified & directed. |
| 70 | M & L for preparation of kerb stone, new un-treated concrete or plastered surfaces of any description over 10cm girth or width, not otherwise described and applying two coats of synthetic enamel paint in black and white colour over a coat of primer complete all as specified and directed. |
| 71 | Material and labour for Machine cut kota stone slab flooring 20 to 25mm thick size not less than 22\\" x 22\\" laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 20mm thick cement screed bed in cement mortar 1:3 including rubbing and mirror polishing complete all as specified and as directed. |
| 72 | Material and labour for pre polished kota stone slab 20 to 25mm thick in riser of steps, skirting, dado and pillars laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10mm thick rendering in cement mortar 1:4 including cutting, moulding outer edges, rubbing and mirror polishing complete all as specified and as directed. |
| 73 | Demolition of Brickwork or stone/boulder masonry, built in lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles. |
| 74 | Material & Labour for Brick work with sub class ‘B’ old size bricks, straight or curved on plan exc 6m mean radius built in CM(1:6) complete all as specified. |
| 75 | M&L for half thick brick work with sub class \\"B\\" bricks straight or curved on plan exceeding 6m mean radius with old size bricks locaaly available built in cement mortar 1:4 complete. |
| 76 | Taking down cement plaster on brick walls/ concrete surface, etc. including raking out joints, hacking for key, scrubbing down with water, etc till brick surfaces all as specified and directed by engr in charge. |
| 77 | M&L 15 mm thick cement plaster on wall in CM (1:6) on fair faces of brick work incl finished even and smooth without using extra cement. |
| 78 | M&L 15 mm thick cement plaster in CM (1:4) on wall ( with approved water proofing compound) on fair faces of brick work incl finished even and smooth without using extra cement.Note: 1. WPC @ 2% of cement, will be paid separately.2. The rate quoted by contractor is deemed to be included necessary scaffolding and formwork as required upto 7.00 Mtr height building. |
| 79 | M&L 5 mm thick cement plaster in CM (1:3) on ceiling surfaces incl finished the surface even and smooth without using extra cement.[Note: By using mechanical device for racking out/ taking down ceiling plaster and NDT and structural repair as specified and as directed by Engr in charge] |
| 80 | M&L for applyiing 15mm plaster with polymer modified mortar fortified with SBR(Nito Bond SBR 45) in proportion 1:3 by weight 5 litr Nitobond SBR 45 added to 50kg cement with 13 litr water and finished surfaces to existing adjoining surface of ceiling, columns, beam and like etc complete all as specified and directed [note : Before repair structural test and repair required] |
| 81 | Supply only Integral water proofing compound |
| 82 | M&L for complete removal of exisiting treatment of wall and applying two coat of oil bound distemper over 1mm thick wall care putty complete all as specified and as directed by engr in charge |
| 83 | M&L for preparation of newly plastered surfaces of walls & applying two coat of distemper oil emulsion over 1mm thick wall care putty complete all as specified and as directed by engr in charge |
| 84 | M&L for preparation of new plastered surface of wall Material & Labour for applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over 1mm thick plaster of paris putty on new surfaces complete all as directed |
| 85 | M&L for complete removal of existing treatment incl preparation of old surfaces, scrubing down, washing etc from walls by scrapping with mechanical wall sander (having mechanical vaccum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7\\"/9\\" to make the surface free from dust, loose paint etc. and applying two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistant as per IS-15489:2004 alkali and fungal resistant exterior paint of required shed (company depot tinted) with silicon additives 1.43 litrs/ 10 Sqm over and including primer coat of exterior primer applied 0.90 litre/10 Sqm over new surfacesincl 1mm thick plaster of paris putty, using Airless spray technology with maximum working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and will execute the same work by authorised applicator as mentioned in PS and acessories complete all as specified and directed. |
| 86 | M&L preapring old plastered surfaces incl washing rubbing down and stopping of distempered and painted surface of ceiling and applying two coat of white wash complete as specified. |
| 87 | M&L for Preparation of new plastered surfaces and applying three coat of white wash on ceiling complete all as specified. |
| 88 | M&L for applying two coat of Synthetic enamal paint over a coat of red oxide primer on new steel based surfaces exc.10cm width or girth including preparation all as specified and directed. |
| 89 | M&L for 75 mm thick plain cement concrete (1:3:6) Type C2 using 40 mm graded aggregates as in plinth protection/paving including finishing surface even and fair without using extra cement complete all as specified and directed |
| 90 | Forming Construction joint 30mm deep x 10mm wide filled with sealing compound, Grade ‘A’ |
| 91 | Providing precast cement concrete Type C0 (1:3:6) 12.50 mm graded aggregate as in louvres and jallies, 25mm thick (measured solid), including all mould- ings but excluding frame complete all as specified and directed. |
| 92 | Material and labour rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive or steel sheeting or other covering, running rails and guides) and hanging; also fastening etc. confirming to Fe 410-W (gde-E-250) quality-A and fixing complete all as specified and as directed. |
| 93 | Supply and fix as in repair rolled mild steel as in joist, channel, angle or tee section/hold fast/wind ties fixed independently with connecting base plate etc conforming to Fe 410W Gde E 250 quality A including dismantling complete all as specified and as directed. |
| 94 | M&L PCC 1:3:6, C-1 (using 20 mm graded stone aggregate) as in bed blocks for inserting holdfast/ filling of steel frame, etc including necessary form work complete as specified and directed. |
| 95 | Taking up or down 15mm dia steel tubing & connection including cleaning for refixing or removal to store complete all as specified & directed. |
| 96 | Taking up or down 20mm dia steel tubing & connection including cleaning for refixing or removal to store complete all as specified & directed. |
| 97 | Supplying and laying of CPVC pipes 20mm outer dia, SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings complete all as specified and directed. |
| 98 | Supplying and laying of CPVC pipes 25mm outer dia, SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including all fittings complete all as specified and directed. |
| 99 | Cutting chases, pinning in brick work, making good to facings where required and pointing in cement mortar 1:3 for concealed water tubing and making good , cutting not exc 10cm girth complete all as directed. |
| 100 | S&F in repairs for MS grating CP 75/100mm dia, without hole and with hole for waste pipe of approved make including fixing with CM to floor/nahani traps etc complete all as directed. |
| 101 | S&F in repairs Mirror cabinet PVC frame of size 400 x 500 mm fixed to wall with rawl plug & stainless steel suitable size screws complete all as specified and direceted. |
| 102 | S & F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes coupling; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 485mm x 420mm bowl size 410mm x 330mm x 160mm |
| 103 | S&F wall mixer with L bend with provision for over head shower complete all as specified and as directed |
| 104 | S&F 15 mm wall mounted sink mixer regular spout with long neck complete all as specified and as directed |
| 105 | S & F in repairs 15 mm bore Bip taps, Chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed. |
| 106 | S & F in repairs, stop valves/Angle valves, 15 mm bore cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions as specified and directed. |
| 107 | S & F in repairs, 15mm bore, PVC connection pipe 450mm long with PTMT nuts at both ends. |
| 108 | S&F in repair Brass chromium plated Tubular towel rail 20mm dia, D type, 60cm long between flanges all as specified and as directed. |
| 109 | S& F as repairs brass chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union 125 mm size complete all as specified and directed. |
| 110 | S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified. |
| 111 | S&F in repairs stainless steel peg set of 6 peg, 45 cm long, complete all as specified. |
| 112 | S&F in repair soap dish of stainless steel fixed to wall with chromium plated brass screws complete all as specified and as directed |
| 113 | S & F in repairs, 10 litres capacity PVC valveless syphonic action type, flushing cistern (ISI marked), low level with inlet, ball valve, float bracket & flush pipe complete all as specified & directed. |
| 114 | S & F in repairs Vitreous china wash basin, white,flat back, size 550 x 400 mm with brackets,excluding pillar cock 15 mm bore CP, PVC connection of 450 mm long including PVC (HDPE) 32 mm bore waste pipe, brass couplings 32 mm CP etc complete all as specified and directed. |
| 115 | S & F 15 mm bore pillar taps, cast copper alloy, chromium plated, fancy type with capstan heads, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe as specified. |
| 116 | S & F vitreous china Semi pedestal pattern (Anglo Indian type) white connection to trap 'P' or 'S' and flush pipe etc including seat cover and making good to disturbed surfaces of floor by filling with PCC 1:4:8 type D-2 to match with existing including taking down the existing old one all as specified and as directed. |
| 117 | S & F mild steel 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete. |
| 118 | Supply and fixing 500 Litre capacity Rotational moulded polyethylene water storage tanks double layered (cylindrical vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. including taking down existing water tanks complete as specified in SSR Part-I |
| 119 | S & F 20 mm bore, Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high-density plastic bal screwed for iron pipe and fixed. (Minimum weight 15mm-142 gms/ 20mm-210 gms/25mm-455gms/ 40mm- 690 gms) |
| 120 | S&F for Gun metal gate valves with iron wheel headscrewed both ends for iron pipes or for unions for 20 mm bore pipes, complete all as specified. |
| 121 | Material & Labour for providing and fixing stainless steel (Grade 304) railing made of hollow tubes,channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, includingfixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement and similar work complete all as specified and as directed. |
| 122 | S & F Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete. |
| 123 | S&F 0.71 mm thick Plain Aluminium sheeting alloy 31000H4 in ridges, hip, valley gutter, crumple joint etc. complete all as specified and directed. |
| 124 | S&F wall mounted Modern kitchen Utensils Dish Rack Stainless steel (31X10X30 inches) t all as specified and directed. |
| 125 | M& L for PVC (SWR) floor trap 100 dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified. |
| 126 | M& L for PVC (SWR) floor trap 75 dia, with grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4) complete all as specified. |
| 127 | Taking down mud plaster on brick or stone wall/APP membrane on roof top etc. including racking out joints, hacking for keys scrubbing down with water etc but lime plaster any description. |
| 128 | M & L for screed bed 15 mm thick in CM 1:4 complete all as specified and directed |
| 129 | M&L for water proofing treatment on RCC roof and parapet wall etc. comprising with the following operation & as specified herein below:- (a)Open the existing surface cracks 6 mm × 6 mm by using the cutter machine and wash & clean the gap with wire brush & clean water. Fill the gaps with (PU Hybrid sealant) of Asian Paints /Dr. Fixit Pidicrete / SmartCare Repair polymer / URP slurry.Substrate must be dry, clean and free from grease, loose particles and dust. Includes checking substrate compressive strength (min. 20 MPa) and cohesive bond strength (min. 1.5 MPa). Repair of damaged / hollow portions with epoxy or polymer-modified mortar, and opening, cleaning & filling of cracks, joints, pipe penetrations and corners with epoxy/polymer mortar or suitable sealant system. Application of Asian Paints SmartCare Two Component Water-based Epoxy Primer @ 100–150 g/sq.m. Second coat of primer to be applied if surface is highly porous (dry patches visible after first coat). (b) Application of 1st coat of SmartCare PU Magnum US, single component PU liquid applied membrane, applied min. 16 hrs after primer application (primer fully cured, surface moisture <4%) @ 700–800 g/sq.m.(c)Providing & placing separation layer of 120–160 GSM geotextile fabric over cured PU Magnum US coating prior to laying protective screed. Carrying out a 48-hour ponding test after completion and rectifying any defects.The rate shall include all materials, labour, T&P, scaffolding, surface preparation, transportation, loading, unloading and all incidental charges complete.Note: Rates for removal of APP and screed be including WPC shall be measured and paid seperately |
| 130 | M&L for special treatment for sunken portion of WCs/Bath & toilet executed in following stage:- Stage1:- Demolition of wc including lime concrete and cemennt concrete etc and preparing of surfaces of existing sunken portion of wc`s or bath etc with wire brush to removed all loose dirts, oil grease etc including removing debries from site of work etc. Stage 2:- Providing 10mm thick plaster in CM 1:3 mixed with integral water proofing chemical of Dr Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantity all as per manufacturere`s instructions. Stage 3:- Apply Dr. Fixit Premeseal primer or equivelent of STP Ltd (and allow to dry for 8 hrs) all as per manufacturer`s instructions. Stage 4:- Apply two coats of water proofing elastomeric coating system of Dr Fixit Raincoats with DFT 100 micron or shilicry 215 of STP (The surfaces after painting one coats shall be allowed to dry for 6 hrs before next coats) Stage 5:- Rendering 10mm thick in CM 1:3 mixed with integral water proofing chemical of Dr Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantity all as per manufacturere`s instructions. Stage 6:- All CI joints shall be filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr. Fixit pidicrete URP all as per manufacturer`s instructions. Stage 7:- Making holes in walls and fixing 600mm long 40mm dia medium grade GI spouts for draining of excess water if any. Stage 8:- Carryout ponding testfor 48 hrs to ensure water tighteness of repaired sunken portion and filling of sunken portion for cement concrete Type E2, 1:5:10 using 40mm graded stone aggregate as in lean concrete complete all as specified and directed. Note:- only plan area shall be measured for payment under this items. (b) Depth of suken portion of WC`s/ bath shall be upto 35 CM which is to be taken into account while coating the rate against this item. (c) The rate shall be quoted by contractor shall be deemed to be included for all the horizontal and verticl treated surface of sunken portion of WC`s/baths. |
| 131 | M&L for 20mm thick granite (of any type) (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform, and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixure of pigment to match the shade of granite complete all as specified and directed. |
| 132 | M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and directed. |
| 133 | M&L for cutting holes in stone /RCC/granite slab for inserting coocking gas cylinder pipe and making good complete all as directed |
| 134 | Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and as directed. |
| 135 | Material and labour for RCC (1:2:4) type B-1 (using 20 mm graded broken stone aggregate) as in slab supported on walls, beams and column in floors, roof landings, balconies, canopies, deck slabs and in shelves complete all as specified and as directed. (Note : Reinforcement shall be measured and paid seperately under relevant) |
| 136 | Material and labour TMT bar 10 mm and over cut to length bent to shape required including cranking bending spirally for hooping for columns, hooking ends and binding with and including MS wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and as directed. |
| 137 | Use and waste formwork to soffits of suspended slabs such as roof slab, floor slabs, landing covers, and similar works, for rough finished flat surfaces of concrete, thickness of slab not exc 200 mm, complete all as specified and directed. |
| 138 | Use and waste of formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizon tal or sloping and similar work exc 5cm but n exc 10cm wide complete all as specified and directed. |
| 139 | Demolition and breaking up 150 mm bore drain pipes, salt glazed stone ware set in cement mortar including PCC haunching and bedding, complete. |
| 140 | S&F salt glazed stone ware drain pipes of 150mm bore, grade `A’, ISI marked, laid to slope in trenches, jointed in CM (1:1) and tested complete all as specified. |
| 141 | M&L for PCC 1:4:8 type D-2 using 40 mm graded crushed stone aggregate in bedding to SGSW/NP2 drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested complete for 150 mm bore pipe all as specified and as directed. |
| 142 | M&L for cutting into existing manholes / Septic tank for connecting new drains making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1 smooth finished and reforming benching as required for 150mm bore pipe. |
| 143 | S&F forCast iron work grade FG 150, unmachined, in brackets, gully traps, gratings, railing, frames, manhole covers, fire and soot doors, dampers, stop valve boxes, gate stops, parts of ranges, balusters and similar articles complete all as specified & as directed. |
| 144 | Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as directed. |
| 145 | S & F Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges of thickness 1.25mm of dia 150mm complete all as specified & as directed. |
| 146 | S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints / solvent cement joints laid in trenches or in floors complete all as specified including dismantling of PCC & taking out old unserviceable 110mm bore PVC pipe with fittings & making good disturbed area complete all as specified & directed. |
| 147 | S &F for PVC (SWR) pipes single soketed, in any length with rubber ring joints, fixed to walls, 110mm bore pipes complete all as specified and directed. |
| 148 | S &F for PVC (SWR) pipes single soketed, in any length with rubber ring joints, fixed to walls, 75mm bore pipes complete all as specified and directed. |
| 149 | S & F for PVC (SWR) bends any radius with access door, 110mm bore complete all as specified and directed. |
| 150 | S & F for PVC (SWR) bends any radius, 110mm bore complete all as specified and directed. |
| 151 | S & F for PVC (SWR) vent cowl, 75mm bore complete all as specified and directed. |
| 152 | S & F for PVC (SWR) bends any radius, 75mm bore complete all as specified and directed. |
| 153 | S & F for PVC (SWR) bends any radius with access door, 75mm bore complete all as specified and directed. |
| 154 | S&F PVC(SWR) Vent cowl 110mm dia. |
| 155 | S&F PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified & directed by Engr-in-Charge. |
| 156 | S &F Sheet glass, 4mm thick frosted glass ordinary quality and glazing with oil putty in Square n exc 0.5 sq. m in each pane |
| 157 | S &F Sheet glass, 4mm thick frosted glass ordinary quality and glazing with oil putty in Square exc 0.5 sq. m in each pane |
| 158 | Dismantling of old cabinet, cupboard/ wardrobe complete all as specified and as directed |
| 159 | M&L for Modular kitchen & Wardrobe / cupboard with 18 mm thick Denacity more than 850 kg/cum one side decorative and other side balancing lamination factory pressed HDHMR Board levies of action Tesa and equivalent including thick PVC edge banding tape with hot alue by edge bending machine etc with auto insing spring loaded hinges (hydraulic type) etc or sliding with track arrangement as directed including necessary accessories like stainless steel handle, Magnetic catch etc and steel baskets of required size mounted on suitable channels with ball bearing to moving of baskets smoothly including all necessary fittings and fixture and 8mm thick both sides Prelaminated BSB (Both side balancing proper) HDHMR of Action Tesa and equivalent as per IS 14587 1998 fixed. Note: Kitchen accessones e baskets. cutlery baskets will be measured and paid separately as supply only |
| 160 | Stainless steel Cutlary basket of size 370mmx485mmx100mm made of min 4mm dia stainless steel wire and bottom of S S perforated sheet approved quality as approved by Engr-in-Charge |
| 161 | Stainless steel thali basket of size 370mmx485mmx200mm made of min 4mm dia stainless steel wire of approved quality as approved by Engr-in-Charge |
| 162 | Stainless steel basket (plain) of size 370mmx485mmx150mm made of min 4mm dia stainless steel wire of approved quality as approved by Engr-in-Charge |
| 163 | S&F in repair soft closing hinges L Bihari complete all as specified and as directed by Engr-in-Charge. |
| 164 | S&F in repair Telescopic channels 300mm long of chromium plated steel, superior quality with stainless steel ball rollers for fixing to cabinets drawers, complete all as specified and as directed |
| 165 | M&L for Coloured Glazed ceramic tiles in vertical surface of size 450X 300X 7 mm thick over 10 mm thick back coat of cement mortar in 1:4 set and jointed in neat cement slurry and pointed in white or colour cement to match over complete all as specified and as directed |
| 166 | M&L for 20 mm thick Granite (of any type) work (table rubbled and polished in steps, Jambs. Pillars, window-cills, cooking platforms and like in cement mortar (1:4) match with shade of granite over 15 mm sceed complete all as specified and directed including painting in white cement (1:2) using marble dust with admixture pigment to match with shade of granite over 15mm screed complete all as specified and directed. |
| 167 | Demolition of Stone slabs and tiles of anydescription or thickness in floors, aprons 22.00 etc, laid bedded and pointed in any mortar complete all as specified and directed |
| 168 | Taking down carefully old unsv copper/aluminium point wiring (light, fan, socket or power) complete,including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets,sunken type box, DBs etc.and removing materials to store for keeping in safe custody for reuse at site or for taking credit and making good to disturbed surfaces of walls, floors etc with its original specification complete all as specified and directed by Engr-in-Charge. |
| 169 | Taking down fan, sealing cable end, dismantling blades and removing ceiling fan any sweep and keeping it in MES store for safe custody and refixing it after minor repair including painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc and hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan Please Enable Macros to View BoQ information |
| 170 | Taking down fan, sealing cable end, dismantling blades and removing ceiling fan any sweep and keeping it in MES store for safe custody and refixing it after minor repair including painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc and hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan Please Enable Macros to View BoQ information |
AI Tender Summary
Tender Timeline
Sep 29, 2026
11:30 IST
Tender Published
Tender notice published.
CompletedNov 02, 2026
17:00 IST
Bid Submission Deadline
Online submission via eProcurement portal.
Upcoming · 29 daysNov 09, 2026
Bid Opening Date
Technical bids will be opened and evaluated.
Upcoming · 36 daysTender Documents
Download All (ZIP) ↓
Disclaimer
We takes all possible care for accurate & authentic tender information. However users are requested to refer Original source of Tender Notice / Tender Document published by Tender Issuing Agency before taking any call regarding this tender